Commtech Wireless 6120 Alphanumeric Pager Turn the pager on by holding the Read Button down for two seconds (oval black button with green stripe). The unit will activate the power on chime, and display Varitronics. This screen will then display the time and date. Eventually the screen will go blank except for the power on symbol, a circle in the left corner of the display. NOTE: Refer to the Commtech Wireless 6120 pamphlet for complete feature and programming capabilities. To scroll through stored messages, press the Read Button to display the last received message. Now press the Left Arrow Key to scroll back through past messages. Use the Right Arrow Key to scroll forward. To clear messages, press the Read Button to display a message. While the message is displayed, hold the Escape Key for 2 seconds to display the Delete Menu. Use the Right Arrow Key to select X (delete the current message) or ALL (delete all the read messages). Press Read Button to confirm. CAUTION: The above procedure will not delete unread messages. To turn the pager off, press the Read Button to display the date screen, then hold the Escape Key (black button with red dot) down until the Settings Menu is displayed. Use the Right Arrow Key to highlight the Off symbol, and press the Read Button twice. The Commtech Wireless 6120 Alphanumeric Pager operates off of a standard AAA battery. Turn unit off when not in use to prolong battery life. further detail on operation and maintenance of your pagers.
Pager System: How To Send Messages How To Send A Page 1) To send a page using the keypad, enter the number of the pager to be paged and then press the PAGE key. The pager unit will vibrate or sound an alert depending on the mode that you have chosen. 2) Press the Read Button. The display will show the room number from which the message was sent. See Diagram 1. Room 10 has sent a Page. 10 Diagram 1 3) Press the Read Button and the message s time stamp will display. See Diagram 2. Page received at 11:01 AM 11:01AM Diagram 2 will display. See Diagram 3. 11:02 AM FRI Diagram 3
How To Send A Page An Accompanying Numerical Message 1) To send a page plus a message using the keypad, enter the number of the pager to be paged. Now press the MESSAGE key, a numerical message (up to four digits) and finally the PAGE key. 2) The pager unit will vibrate or sound an alert depending on the mode that you have chosen. Press the Read Button. The display will show the room number and *alphanumeric or numerical message. See Diagram 4. Room 10 has sent a message code 99. 10 EMERGENCY! Diagram 4 *Alphanumeric messages are factory preset. Up to 20 canned messages can be assigned to any message numbers 0-9999. 3) Press the Read Button again and the message s time stamp will display. See Diagram 5. Page received at 1:01 PM 1:01 PM Diagram 5 will display. See Diagram 6. 1:02 PM FRI Diagram 6
How To Send An All Page 1) To send an All Page using the keypad, enter the number 0 or an assigned common address number. Then press the PAGE key. All pager units or pagers of an assigned common address number will vibrate or sound an alert depending on the mode that you have chosen. 2) Press the Read Button on the front of the pager. The display will show the room number from which the All Page was sent. See Diagram 7. Room 10 has sent an All Page. 10 Diagram 7 3) Press the Read Button again and the message s time stamp will display. See Diagram 8. Page received at 2:05 PM Diagram 8 2:05 PM will display. See Diagram 9. 2:05 PM FRI Diagram 9 further detail on protecting, selective deleting, and erasing messages.
How To Set Timer with Call Back Feature 1) To set the timer using the keypad, enter the number of minutes you would like the timer to count down. Then press the "Message" key and enter the pager number you would like to Call Back to the room you are timing down in. Now press the "Timer" key. 2) After the timer has timed down the selected pager will vibrate or sound an alert depending on the mode that you have chosen. 3) Press the Read Button on the front of the pager. The display will show the room number that the time down procedure occurred in. See Diagram 10. Room 6 has sent a Call Back Page. 6 Diagram 10 4) Press the Read Button again and message s time stamp will display. See Diagram 11. Page received at 3:10 PM 3:10 PM Diagram 11 5) Press the Escape Button and the current time and date will display. See Diagram 12. 2:05 PM FRI Diagram 12 further detail on protecting, selective deleting, and erasing messages.