Juniper Networks EX2500 Ethernet Switch Web Device Manager Guide Release 3.0 Juniper Networks, Inc. 1194 North Mathilda Avenue Sunnyvale, CA 94089 USA 408-745-2000 www.juniper.net Part Number: 530-029704-01, Revision 1
Juniper Networks, the Juniper Networks logo, JUNOS, NetScreen, ScreenOS, and Steel-Belted Radius are registered trademarks of Juniper Networks, Inc. in the United States and other countries. JUNOSe is a trademark of Juniper Networks, Inc. All other trademarks, service marks, registered trademarks, or registered service marks are the property of their respective owners. Juniper Networks assumes no responsibility for any inaccuracies in this document. Juniper Networks reserves the right to change, modify, transfer, or otherwise revise this publication without notice. Products made or sold by Juniper Networks or components thereof might be covered by one or more of the following patents that are owned by or licensed to Juniper Networks: U.S. Patent Nos. 5,473,599, 5,905,725, 5,909,440, 6,192,051, 6,333,650, 6,359,479, 6,406,312, 6,429,706, 6,459,579, 6,493,347, 6,538,518, 6,538,899, 6,552,918, 6,567,902, 6,578,186, and 6,590,785. Juniper Networks EX2500 Ethernet Switch Web Device Manager Guide, Release 3.0 Copyright 2009 Juniper Networks, Inc. All rights reserved. Writing: William Rogers Editing: Taffy Everts Illustration: William Rogers Revision History 11 April 2009 Revision 1 The information in this document is current as of the date listed in the revision history. SOFTWARE LICENSE The terms and conditions for using this software are described in the software license contained in the acknowledgment to your purchase order or, to the extent applicable, to any reseller agreement or end-user purchase agreement executed between you and Juniper Networks. By using this software, you indicate that you understand and agree to be bound by those terms and conditions. Generally speaking, the software license restricts the manner in which you are permitted to use the software and may contain prohibitions against certain uses. The software license may state conditions under which the license is automatically terminated. You should consult the license for further details. For complete product documentation, see the Juniper Networks Web site at http://www.juniper.net/techpubs. ii
Table of Contents About This Guide v Objectives... v Audience... v Supported Platforms... vi Documentation Conventions... vi List of Technical Publications... vii Documentation Feedback... vii Requesting Technical Support... vii Self-Help Online Tools and Resources... viii Opening a Case with JTAC... viii Chapter 1 Getting Started 1 EX2500 Web Device Manager Features...1 EX2500 Web Device Manager Requirements...2 Switch Setup...2 IP Interfaces...2 Enabling and Disabling EX2500 Web Device Manager Access...2 Web Browser Setup...2 Starting the EX2500 Web Device Manager...3 Chapter 2 EX2500 Web Device Manager Basics 7 Window Layout...8 Toolbar...9 Context Tabs...9 Commands...9 Navigation Window...10 Forms Window...10 Message Window...11 Chapter 3 Using the Dashboard 13 Dashboard Overview...13 Displaying Dashboard Forms...13 Chapter 4 Configuring the Switch and Loading Software 15 Web Device Manager Configuration Overview...15 Viewing or Configuring Switch Parameters...15 Loading Switch Software...17 Chapter 5 Viewing Monitor Statistics 19 Web Device Manager Monitor Overview...19 Displaying Statistics...19 Table of Contents iii
EX2500 Ethernet Switch Web Device Manager Guide iv Table of Contents
About This Guide This preface provides the following guidelines for using the Juniper Networks EX2500 Ethernet Switch Web Device Manager Guide: Objectives on page v Audience on page v Supported Platforms on page vi Documentation Conventions on page vi List of Technical Publications on page vii Documentation Feedback on page vii Requesting Technical Support on page vii Objectives EX2500 Web Device Manager software, included with the Juniper Networks EX2500 Ethernet Switch, lets you use your Web browser to access switch information and statistics, and to perform switch configuration via the Internet. This guide provides an overview of how to access and use the EX2500 Web Device Manager. For details about the switch information, statistics, and configuration parameters available from the EX2500 Web Device Manager, see the EX2500 Ethernet Switch Command Reference and EX2500 Ethernet Switch Configuration Guide. NOTE: This guide documents Release 3.0 of the EX2500 Ethernet Switch. For additional information either corrections to or information that might have been omitted from this manual see the EX2500 Ethernet Switch Release 3.0 Release Notes at http://www.juniper.net/. Audience This guide is intended for network installers and system administrators engaged in configuring and maintaining a network. Administrators must be familiar with the EX2500 switch, a Web browser, Ethernet concepts, IP addressing, the IEEE 802.1D Spanning Tree Protocol, and SNMP configuration parameters. Objectives v
EX2500 Ethernet Switch Web Device Manager Guide Supported Platforms The features described in this guide are supported by only the EX2500 software running on EX2500 Ethernet Switches only. Documentation Conventions Table 1 describes the notice icons used in this manual. Table 2 describes the EX2500 text and syntax conventions. Table 1: Notice Icons Icon Meaning Description Informational note Indicates important features or instructions. Caution Indicates a situation that might result in loss of data or hardware damage. Warning Alerts you to the risk of personal injury or death. Laser warning Alerts you to the risk of personal injury from a laser. Table 2: EX2500 Text and Syntax Conventions (1 of 2) Convention Usage Examples Bold text like this Bold text like this Braces { } Brackets [ ] Fixed-width text like this Italic text like this <Italic text like this in angle brackets> Plain text like this Names of windows, dialog boxes, buttons, tabs, and other objects in a user interface that you click or select In syntax descriptions and set-off command examples, text you must type exactly as shown Required elements in syntax that has more than one option. You must choose one of the options. Do not type the braces. Optional elements in syntax descriptions. Do not type the brackets. Onscreen computer output Book titles, special terms, and words to be emphasized Variables in command syntax. Replace the italic text with the appropriate real name or value when entering the command. Do not type the brackets. Names of commands, files, and directories used within the text Click the Submit button on the bottom of the form. Main# sys show portchannel {<1-12> hash information} (For example, you can enter either show portchannel 3, show portchannel hash, or show portchannel information.) copy running config tftp [data-port mgt-port] (You enter either copy running config tftp data-port, copy running config tftp mgt-port, or copy running config tftp.) ex2500(config)# reload Reset will use software image2... See the EX2500 Ethernet Switch Command Reference. To establish a Telnet session, enter host# telnet <IP address> (For example, you can enter telnet 192.32.10.12.) View the readme.txt file. vi Supported Platforms
About This Guide Table 2: EX2500 Text and Syntax Conventions (2 of 2) Convention Usage Examples Vertical line Separates choices for command keywords and arguments. Enter only one choice. Do not type the vertical line. copy running config tftp [data-port mgt-port] (You enter either copy running config tftp data-port, copy running config tftp mgt-port, or copy running config tftp.) List of Technical Publications Table 3: EX2500 Ethernet Switch Documentation Table 3 lists the documentation supporting the EX2500 Ethernet Switch. All documentation for EX Series Ethernet Switches is available at http://www.juniper.net/techpubs/. Document EX2500 Ethernet Switch Quick Start EX2500 Ethernet Switch Hardware Guide EX2500 Ethernet Switch Web Device Manager Guide EX2500 Ethernet Switch Configuration Guide Description Provides brief installation and initial configuration instructions. Provides information and instructions for installing an EX2500 Ethernet Switch. Provides an overview of how to access and use the EX2500 Web Device Manager. Describes how to configure and use the software on the EX2500 Ethernet Switch. EX2500 Ethernet Switch Command Reference Describes how to configure and use the software with your EX2500 Ethernet Switch. The reference lists each command and includes the complete syntax and a functional description, using the EX2500 command-line interface (CLI) EX2500 Ethernet Switch Release 3.0 Release Notes Summarize EX2500 switch features and known problems, provide information that might have been omitted from the manuals, and provide upgrade and downgrade instructions. Documentation Feedback We encourage you to provide feedback, comments, and suggestions so that we can improve the documentation. Send e-mail to techpubs-comments@juniper.net with the following information: Document URL or title Page number Software version Your name and company Requesting Technical Support Technical product support is available through the Juniper Networks Technical Assistance Center (JTAC). If you are a customer with an active J-Care or JNASC support contract, or are covered under warranty, and need postsales technical support, you can access our tools and resources online or open a case with JTAC. List of Technical Publications vii
EX2500 Ethernet Switch Web Device Manager Guide JTAC policies For a complete understanding of our JTAC procedures and policies, review the JTAC User Guide located at http://www.juniper.net/customers/support/downloads/710059.pdf. Product warranties For product warranty information, visit http://www.juniper.net/support/warranty/. JTAC hours of operation The JTAC centers have resources available 24 hours a day, 7 days a week, 365 days a year. Self-Help Online Tools and Resources For quick and easy problem resolution, the Juniper Networks online self-service portal the Customer Support Center (CSC) provides the following features: Find CSC offerings: http://www.juniper.net/customers/support/ Search for known bugs: http://www2.juniper.net/kb/ Find product documentation: http://www.juniper.net/techpubs/ Find solutions and answer questions using our Knowledge Base: http://kb.juniper.net/ Download the latest versions of software and review release notes: http://www.juniper.net/customers/csc/software/ Search technical bulletins for relevant hardware and software notifications: http://www.juniper.net/alerts/ Join and participate in the Juniper Networks Community Forum: http://www.juniper.net/company/communities/ Open a case online in the CSC Case Management tool: http://www.juniper.net/cm/ To verify service entitlement by product and serial number, use our Serial Number Entitlement (SNE) Tool at http://tools.juniper.net/serialnumber/entitlementsearch/. Opening a Case with JTAC You can open a case with JTAC on the Web or by telephone. Use the Case Management tool in the CSC at http://www.juniper.net/cm/. Call 1-888-314-JTAC (1-888-314-5822 toll-free in the USA, Canada, and Mexico). For international or direct-dial options in countries without toll-free numbers, visit us at http://www.juniper.net/support/requesting-support.html. viii Requesting Technical Support
Chapter 1 Getting Started This chapter briefly describes the software features and requirements for the EX2500 Web Device Manager, and explains how to access the Web Device Manager start page: EX2500 Web Device Manager Features on page 1 EX2500 Web Device Manager Requirements on page 2 Switch Setup on page 2 Web Browser Setup on page 2 Starting the EX2500 Web Device Manager on page 3 EX2500 Web Device Manager Features Network administrators can access switch configuration and monitoring functions through the Web Device Manager. The Web Device Manager has the following features: Many of the same configuration and monitoring functions as the command-line interface (CLI) Intuitive and easy-to-use interface structure Password protection Nothing to install; the Web Device Manager is part of the EX2500 switch software Automatic upgrades with each new software release NOTE: You can perform most configuration and monitoring tasks through the Web Device Manager. For a comprehensive set of commands, use the command-line interface (CLI). See the EX2500 Ethernet Switch Command Reference. EX2500 Web Device Manager Features 1
EX2500 Ethernet Switch Web Device Manager Guide EX2500 Web Device Manager Requirements EX2500 switch Installed EX2500 switch software PC or workstation with network access to the switch s management interface, as configured using the management module Frame-capable Web-browser software, such as the following: Netscape Navigator 4.7x or later Internet Explorer 6.0x or later Mozilla FireFox 1.0.4 or later JavaScript enabled in your Web browser Switch Setup Before you can access the Web Device Manager, minimal configuration is required on the EX2500 switch. IP Interfaces At least one IP interface must be configured on the switch. Each IP interface address provides a point of access for EX2500 switch management. The default management interface is 1, which allows access to EX2500 switch management. For complete information about configuring IP interfaces, see your EX2500 Ethernet Switch Hardware Guide. Enabling and Disabling EX2500 Web Device Manager Access By default, Web Device Manager access is enabled. If you need to disable or re-enable access, use the following command from the command-line interface: ex2500(config)# [no] access http enable For more information about accessing and configuring the switch through the CLI, see your EX2500 Ethernet Switch Command Reference. Web Browser Setup Most modern Web browsers work with frames and JavaScript by default, and require no additional setup. However, you should check your Web browser s features and configuration to make sure frames and JavaScript are enabled. NOTE: JavaScript is not the same as Java. Please make sure that JavaScript is enabled in your Web browser. 2 EX2500 Web Device Manager Requirements
Chapter 1: Getting Started Starting the EX2500 Web Device Manager When the switch and browser setup is done, follow these steps to launch the Web Device Manager: 1. Start your Web browser. 2. Enter the switch IP interface address or domain name in the Web browser s URL field. For example, if your switch has an IP interface with a network IP address of 10.10.10.1, you could enter the following: If the IP interface s address has a name on your local domain name server, you could enter the name instead. For example, you could enter the following: Starting the EX2500 Web Device Manager 3
EX2500 Ethernet Switch Web Device Manager Guide 3. Log in to the switch. If your switch and browser are properly configured, you are prompted to enter a password: Enter the account name and password for the switch s administrator or user account. The default account name is admin, and the default password is admin. For more password information, see your EX2500 Ethernet Switch Command Reference. 4 Starting the EX2500 Web Device Manager
Chapter 1: Getting Started 4. Allow the Web Device Manager Dashboard page to load. When you enter the proper account name and password combination, the Web Device Manager Dashboard page appears in your browser s viewing area. You might experience a slight delay while the Dashboard page is being initialized. Do not stop the browser while loading is in progress. When loading is complete, a folder icon appears in the left-hand navigation window. NOTE: The sample screens that appear in this guide might differ slightly from the screens displayed by your system. Screen content varies based on the type of switch unit that you are using and the firmware versions and options that are installed. Starting the EX2500 Web Device Manager 5
EX2500 Ethernet Switch Web Device Manager Guide 6 Starting the EX2500 Web Device Manager
Chapter 2 EX2500 Web Device Manager Basics This chapter describes the format and organization of the EX2500 Web Device Manager: Window Layout on page 8 Toolbar on page 9 Navigation Window on page 10 Forms Window on page 10 Message Window on page 11 7
EX2500 Ethernet Switch Web Device Manager Guide Window Layout Once you are properly logged in, the EX2500 Web Device Manager appears in your Web browser s viewing window: Use the four regions on an EX2500 Web Device Manager screen as follows: Toolbar Select the context for your actions in the other windows. (See Toolbar on page 9.) Navigation window Select particular items or features to act upon. (See Navigation Window on page 10.) Forms window View or alter switch information. (See Forms Window on page 10.) Message window Display the most recent switch syslog messages and events. (See Message Window on page 11.) 8 Window Layout
Chapter 2: EX2500 Web Device Manager Basics Toolbar The toolbar consists of context tabs and commands. Context Tabs Use the three context tabs in the toolbar to set the context for your actions in the application: Dashboard Configure Monitor Selected by default when the Web Device Manager is first activated. When selected, basic switch information and status appears in the forms window. Select an item in the navigation window to display the desired dashboard information in the forms window. When selected, you can access the switch configuration forms. Configuration forms can be altered only if you are logged in using the administrator account. Select an item in the navigation window to display the desired configuration form in the forms window. When selected, you can view information about switch performance. Select an item in the navigation window to display the desired statistics in the forms window. The selected context tab is highlighted, to remind you of the current context mode. Commands The following general commands are available on the toolbar: Save to Active Config Save to Backup Config Show Config Show Log Help Logout Saves the current configuration to the startup configuration block. Saves the current configuration to the backup configuration block. Opens a new Web browser window that displays the running configuration. Opens a new Web browser window that displays the most recent switch log messages. Close the log browser when you are finished. Opens a new Web-browser window that displays basic online help information. Close the Help browser when you are finished. Logs off from the switch and exits the Web Device Manager. Toolbar 9
EX2500 Ethernet Switch Web Device Manager Guide Navigation Window The navigation window is used for selecting a particular switch feature to act upon. Status, statistics, or configuration forms for the selected item will appear in the forms window, depending on the context chosen on the toolbar. The navigation window contains a tree of folders, sub-folders, and feature icons: You can click any closed folder to open it and reveal its contents. Click any open folder to close it. Click any feature icon to load the appropriate status, statistics, or configuration form in the forms window. Some folders also have forms. If the name of the folder is underlined, click the name to display the appropriate form. Forms Window When a feature icon is selected on the navigation window, a status, statistics, or configuration form is displayed in the forms window. The exact nature of the form depends on the current context selected on the toolbar, as well as the type of information available. Not all feature icons have forms for all contexts. Some forms display switch information such as settings, status, or statistics. Others allow you to make configuration changes to switch parameters. 10 Navigation Window
Chapter 2: EX2500 Web Device Manager Basics Message Window Switch log messages are generated by events such as login and logout activity, password changes, configuration changes, and switch reboots. The Web Device Manager records the most recent messages and displays each one briefly in the message window. When the last message has been displayed, the cycle is repeated. To view all messages at the same time, select the Show Log command on the toolbar. A new Web browser window will open to display the log information. Close the window when you are finished. Message Window 11
EX2500 Ethernet Switch Web Device Manager Guide 12 Message Window
Chapter 3 Using the Dashboard This chapter describes how to use the EX2500 Web Device Manager dashboard feature: Dashboard Overview on page 13 Displaying Dashboard Forms on page 13 Dashboard Overview The EX2500 Web Device Manager can display the present settings and operating status of a variety of switch features. The same information available through the switch s command-line interface (CLI) is present on the dashboard forms. The following section provides a basic outline for viewing the dashboard forms. You should first be familiar with the configuration commands in the EX2500 Ethernet Switch Command Reference. Displaying Dashboard Forms Follow these basic steps for viewing switch dashboard forms: 1. Select the Dashboard context tab in the Web Device Manager toolbar: Dashboard Overview 13
EX2500 Ethernet Switch Web Device Manager Guide 2. Select a feature icon in the navigation window. For example: 3. View information shown in the forms window. For example: NOTE: Items that load other forms when selected are underlined. 14 Displaying Dashboard Forms
Chapter 4 Configuring the Switch and Loading Software This chapter explains how to configure the EX2500 switch and load switch software from the Web Device Manager: Web Device Manager Configuration Overview on page 15 Viewing or Configuring Switch Parameters on page 15 Loading Switch Software on page 17 Web Device Manager Configuration Overview The EX2500 Web Device Manager can be used to view and change switch configuration parameters. The same configuration parameters that are available through the switch s command-line interface (CLI) are present on the Web Device Manager configuration forms. The following section provides a basic outline for switch configuration. You should first be familiar with the configuration commands in the EX2500 Ethernet Switch Command Reference. NOTE: To change switch configuration settings, you must be logged in using the administrator account. Viewing or Configuring Switch Parameters Follow these basic steps for viewing or configuring switch parameters: 1. Click the Configure context tab in the Web Device Manager toolbar: Web Device Manager Configuration Overview 15
EX2500 Ethernet Switch Web Device Manager Guide 2. Select a feature icon in the navigation window. For example: 3. View or make changes to the settings shown in the forms window. For example: NOTE: Fields that must be configured for proper switch operations are highlighted on the forms in GREEN type. Items that load other forms when selected are underlined. 4. Click the Submit button on the bottom of the form to submit the form contents to the switch. 16 Viewing or Configuring Switch Parameters
Chapter 4: Configuring the Switch and Loading Software Loading Switch Software You can use the Web Device Manager to load software onto the EX2500 switch. The software image to load can reside in one of the following locations: TFTP server Local computer After you log in to the Web Device Manager, perform the following steps to load a software image: 1. Click the Configure context tab in the Web Device Manager toolbar: 2. In the Navigation Window, select System > Config/Image Control. Loading Switch Software 17
EX2500 Ethernet Switch Web Device Manager Guide The Switch Image and Configuration Management page appears. 3. Enter the server s information in the TFTP Settings section. 4. In the Image Settings section, next to Image for Transfer, select the image version you want to replace:. 5. Enter the filename, and click Get Image. Once the image has loaded, the page refreshes to show the new software. 18 Loading Switch Software
Chapter 5 Viewing Monitor Statistics This chapter explains how to monitor EX2500 switch performance from the Web Device Manager: Web Device Manager Monitor Overview on page 19 Displaying Statistics on page 19 Web Device Manager Monitor Overview The EX2500 Web Device Manager monitor forms can be used to view a variety of switch performance statistics. The same statistics that are available through the switch s command-line interface (CLI) are present on the Web Device Manager monitor forms. The following section provides a basic outline for viewing monitor statistics. You should first be familiar with available statistics as covered in the EX2500 Ethernet Switch Command Reference. Displaying Statistics Follow these basic steps for viewing switch statistics: 1. Select the Monitor context tab in the Web Device Manager toolbar: Web Device Manager Monitor Overview 19
EX2500 Ethernet Switch Web Device Manager Guide 2. Select a feature icon or underlined folder in the navigation window. For example: 3. View the statistics in the forms window. For example: NOTE: Items that load other forms when selected are underlined. 20 Displaying Statistics