HP StoreEver Command View for Tape Libraries Version and Interface Manager Firmware Version I274 Release Notes

HP StoreEver Command View for Tape Libraries Version 3.8.00 and Interface Manager Firmware Version I274 Release Notes HP Part Number: QN998-96146 Published: October 2014 Edition: 21

Version: Description Command View for Tape Libraries version 3.8.00 and Interface Manager firmware version I274 This document describes enhancements and fixes for HP Command View for Tape Libraries 3.8.00 and Interface Manager firmware version I274. HP SMI-S Tape Provider runs in the background on Command View for Tape Libraries. Update recommendation Optional. Supersedes Command View for Tape Libraries versions 3.7.00, 3.7.01, and 3.7.02 Product models Supports all models of HP ESL E-Series Tape Library. Supports all models of HP ESL G3 Tape Library. Supports all models of HP EML E-Series Tape Library. Supports HP 1/8 G2 Tape Autoloaders. Supports HP MSL2024, MSL4048, MSL6480, and MSL8096 Tape Libraries. Includes TapeAssure for selected tape drives in HP MSL G3 Tape Libraries, 1/8 G2 Tape Autoloaders, and some standalone LTO Ultrium tape drive models. For more information, see http://www.hp.com/go/tapeassure. Operating systems Operating System Microsoft Windows Server 2008 SP2 (32/64 bit) Microsoft Windows Server 2008 R2 SP1 (64 bit) Microsoft Windows Server 2012 (64 bit) Microsoft Windows Server 2012 R2 (64 bit) Supported Yes Yes Yes Yes NOTE: Command View TL runs as a 32 bit application on the listed Microsoft Windows Operating Systems (64 bit). Command View TL software is fully compatible with only English-language versions of Windows. Management station (server) requirements Minimum system For environments with fewer than 10 tape libraries, Command View TL requires a management station (server) with a minimum of: 1.6-GHz CPU, 2 GB RAM 2 GB of free disk space for installation 2 Description

10/100 Base-T network card (static IP address recommended) Compatible with VMWare ESX server 5.0 and 5.1 Recommended system For environments with up to 20 tape libraries: 3.0-GHz CPU or greater, Dual Core, 8-GB RAM For environments with 20 to 70 tape libraries: 3.0-GHz CPU or greater, Dual Core, 16-GB RAM For environments with more than 70 tape libraries, or more than 900 tape drives (total), multiple management stations will be required. Browser minimum requirements Microsoft Internet Explorer v8, v9, v10, and v11 Mozilla Firefox v15.0.1 or higher Google Chrome v24 or higher Adobe Flash Player 10.3 or greater NOTE: On Windows Server 2012 Internet Explorer 10 has an embedded version of Adobe Flash Player. Ensure that all of the latest Windows updates are installed. 1. Ensure that the most recent Windows updates are installed using the Windows update feature in the Control Panel. The minimum requirements are: All windows security updates released thru April 2013 The Cumulative Security Update for Internet Explorer 10 for Windows Server 2012 (KB2809289) 2. Configuring Windows Server 2012: a. Click Server Manager in the bottom left corner of the screen. b. In the Server Manager dialog box, click Add Roles and Features Wizard. c. Continue with Next with the default options selected and provide specific options in the wizard. d. In the Features dialog box choose User Interfaces and Infrastructure (installed). This feature has three sub-features. Select the Desktop Experience check box. e. Click Next and the Install. 3. Configure Internet Explorer: a. Select Tools Compatibility View Settings. b. Enter the website address, then click Add. c. Verify the Include updated websites lists from Microsoft and Display intranet sites in Compatibility View check boxes are selected. d. Click Close. NOTE: Clearing the Internet Explorer cache will remove the added websites in Compatibility View Settings. If the cache is cleared, the websites must be added back to the Compatibility View Settings list. For ESL G3 Tape Libraries (only) Java Runtime Environment (JRE) version 1.6.0 Update 24 Enable Java support for Browsers: Browser minimum requirements 3

1. Close all open browser windows. 2. From the Windows Control Panel, select Java. 3. Select the Advanced tab. 4. Expand the Default Java for browsers node and select the item for your browser if it is not already selected. 5. Click OK. An internet connection is recommended so that Command View for Tape Libraries can connect to the HP Support website. Recommended minimum screen resolution 1152 x 864 Compatibility/Interoperability For full functionality of all new features, please make sure that you are using the following firmware versions: Product Version ESL G3 Tape Library Library Command View TL LTO6 drives LTO5 drives LTO4 drives 680H_GS30501 MCB Ver 2 656H_GS01501 MCB Ver 1 1 3.8.00 J3PW I6GW H6HW ESL E-Series Tape Library Library (and robotics) Command View TL Interface Manager 2Gb Fibre Channel Interface Controllers 4Gb Fibre Channel Interface Controllers LTO5 drives LTO4 drives LTO3 drives 7.7 3.8.00 I274 5.9.63 5.9.77 I6GW H6FW L68W EML E-Series Tape Library Library (and robotics) Command View TL Interface Manager 2Gb Fibre Channel Interface Controllers 4Gb Fibre Channel Interface Controllers LTO6 drives LTO5 drives 1493 3.8.00 I274 5.9.63 5.9.77 J3GS I6DS 4 Recommended minimum screen resolution

Product LTO4 drives LTO3 drives Version H68S L6HS MSL Tape Libraries MSL6480 MSL G3 2048 MSL G3 4048 MSL G3 8048 MSL G3 8096 4.40 6.20 8.70 1130 1130 Autoloader 1/8 Autoloader 4.30 MSL StoreEver Drive Firmware versions LTO6 Drives HH 2 FC - 23MW HH SAS - 33OW LTO5 Drives FH 2 FC - I6GW HH FC - Y6DW HH SAS - Z6DW LTO4 Drives FH FC - H6FW HH SAS - U62W 1 In Command View TL, the Library TapeAssure feature support will be available for ESL G3 library for the stated firmware versions of ESL G3 Tape Library 663H or later with MCB Version 2.0. 2 HH Half Height For the latest FW versions supported, refer to the HP Enterprise Backup Solutions (EBS) matrix located at: http://www.hp.com/go/ebs. Incompatibility with Secure Key Manager 1.0 (4.7.1) This package is NOT compatible with HP Secure Key Manager code version 1.0 (also known as 4.7.1). If you are using a Secure Key Manager appliance for storage security, code version 1.1 (also known as 4.8.1) is required. Command View TL Database Compatibility From CVTL 3.0.00 and higher, using the Save/restore Database in TapeAssure and restoring the database backup taken from older versions of Command View TL is not supported. Command View TL Database Compatibility 5

Command View TL upgrade support NOTE: Upgrading to Command View TL 3.8.00 is only supported from versions 3.6.00, 3.6 Patch 01, 3.7.00, 3.7 Patch 01, and 3.7 Patch 02. If your current Command View TL software is older than 3.6.00, then upgrade to version 3.6.00 before you upgrade to 3.8.00. Command View TL Operating System Microsoft Windows Server 2008 SP2 (32/64 bit) Microsoft Windows Server 2008 R2 SP1 (64 bit) Microsoft Windows Server 2012 (64 bit) Microsoft Windows Server 2012 R2 (64 bit) 3.8.00 Yes Yes Yes Yes Languages International English Enhancements Version 3.8.00 New features in Command View TL Data Verification Support for LTO-6 and LTO-5 tape drives in the MSL6480 tape library Support for scanning encrypted, partitioned, and LTFS partitioned tapes Modify partition and Custom partition enhancements for ESL G3 Time base Policy and TapeAssure Policy enhancements for ESL G3/ MSL6480 Support for multiple drive generations in the same data verification partition for MSL6480 and ESL G3 Graphical representation of data verification and drive assessment results on the Data Verification tab Included in the list of Event Triggered Scans Data transfer in Library TapeAssure Graphs Windows 2012 R2 and IE 11 support HP SMI-S Tape Provider Fixes HP SMI-S Tape Provider is updated to version 3.8.00 with Command View TL 3.8.00. See the HP StoreEver SMI-S Tape Provider Release Notes at http://www.hp.com/support/cvtl. Version 3.8.00 Upgrade to Java version 7.0.600. Fixed an issue where the CVTL nag warning was not removed after a license was installed. 6 Command View TL upgrade support

Fixed the EML drive upgrade page to indicate that it handles LTO-6 drives. Fix for multiple alerts on a cartridge load. Fixed an issue where Advance Tape Assure was always showing 0 modules in the library Overview pane. Increased the length of the application name in the tapes table data base that was causing some support tickets to be rejected for Tape Assure data. HP SMI-S Tape Provider See the HP StoreEver SMI-S Tape Provider Release Notes at http://www.hp.com/support/cvtl. Installation instructions Installing Command View for Tape Libraries as a new install NOTE: HP Command View for Tape Libraries 3.0.00 and later uses Adobe Flash Player. If you have an internet connection, then from the Command View TL server, launch http://get.adobe.com/ flashplayer/ and download flash player with an administrator account. Do not upgrade to Command View Tape Library 3.0.00 or later if you are unable to install flash player. If you have issues in installing Adobe Flash Player, uninstall and reinstall it. Right-click the executable file and select Run as administrator. The latest CVTL version is available at www.hp.com/support/cvtl. To install and run this software on Windows Server 2008 or later, you must either login as Administrator and right-click and run as Administrator, or perform the following steps: 1. Become a member of the Administrators group using the Server Manager (Start All Programs Administrative Tools Server Manager). 2. If prompted by Internet Explorer, add the hostname of the management station to your Trusted Sites Zone. 3. Launch the Command View TL installer by right-clicking on the executable and selecting Run as Administrator. The Windows Management Instrumentation service must be started before installation or uninstallation of Command View TL. No changes are required to remotely browse to a library or management station. Install the Command View for Tape Libraries upgrade CAUTION: Command View TL 3.0.00 and later cannot upgrade any libraries with i240 or older Interface Manager firmware. Upgrade to 2.8.00, then install the bundle, and then install Command View TL 3.0.00 to 3.5.00. Command View 3.6.00 can only be upgraded from 3.5.00, and Command View 3.8.00 can only be upgraded from 3.6.00 or later. If you are upgrading from a Command View TL version earlier than 2.0.00 (or Command View ESL prior to version 1.5), follow this upgrade path: 2.32 or 2.8.00 to 3.5.00 to 3.6.00 to 3.8.00. Command View TL 3.8.00 upgrade is supported from versions 3.6.00 or later. Command View TL 3.8.00 upgrade is supported from versions 3.6.00 or later. All previous settings (database, device list, support tickets, proxy settings and so forth) are migrated during the upgrade. Upgrade Adobe Flash player to a newer version. For information on CVTL installation, see Installation instructions (page 7). Installation instructions 7

NOTE: If Command View TL is uninstalled using add remove programs and the data base and files were retained, install the same version of Command View TL before migration. To install Command View TL, you must uninstall the database and all files. Installing the Interface Manager upgrade If upgrading your Interface Manager from an I231 or lower release, ensure that the FTP server on the Interface Manager is clear of all extra files. CAUTION: intervention. Failure to clear these files may result in damage to the library and the need for service 1. If you have a firewall that prevents FTP access, disable the firewall. 2. Use FTP to connect to the Interface Manager: 1. Open a command shell on any PC connected to the LAN. 2. Enter the command ftp ipaddress, where ipaddress is the IP address of the Interface Manager card. 3. Log in with the user name ftp and no password. 3. Run del <filename> for each file to delete. CAUTION: HP recommends that an HP Service engineer perform any upgrade of your Interface Manager from an I2XX or lower release. The HP Service engineer will upgrade to version I232 using CVTL 2.3.20 and the corresponding firmware bundle using the ESL c01464098 or EML c01463974 engineering document using CVTL 2.3.20. After the library is an I232 and the corresponding bundles, Command View TL can be updated to 2.8.00. The library can then be downloaded to I274. I232 and I240 cannot be upgraded with Command View TL 3.0.00 and above. 8 Installation instructions

Use advisory ESL-e c01464098 or EML c01463974 to upgrade directly to I232 and CVTL 2.8.00 from any revision less than I232. Then, perform the upgrade to I270 using CVTL 2.8.00. CAUTION: Customers upgrading from HP StorageWorks ESL E-Series library firmware 6.20 to 6.22 or higher via Interface Manager or Command View TL in an HP StorageWorks ESL E-Series library will encounter the following message: Interface Manager (IM) unable to verify whether firmware update completed or not, please check the device. Wait until the library Operator Control Panel indicates the upgrade is complete. This will take about 20 minutes. The upgrade will complete with no issues. This error will not occur once the firmware is fully installed in the library. Failure to wait may result in damage to the library and the need for service intervention. CAUTION: ESL E-Series libraries that have had the cabinet controller or cabinet controller smart media/daughter board replaced without having library defaults reset afterwards, must restore library defaults prior to upgrading to 7.X or higher firmware (first included in the 2.4 or higher firmware bundle). If the history of the library is unknown, it is recommended that library defaults be reset prior to loading 7.0 to be safe. Library defaults are different than restoring the Interface Manager defaults; restoring library defaults must be done from the front panel (Operator Control Panel) of the library in the Setup menu. CAUTION: Customers upgrading from HP EML libraries from below 1200 need to go to 1200 first. Secondly if the firmware is below 1407 then they need to upgrade to 1407 next. Then they can upgrade to the latest firmware. EML libraries might not show the latest revision is loaded until the IFC is also rebooted if no host commands were sent to the library after the upgrade. This configuration data includes, but is not limited to: Management Station information Library settings Support contact information Interface Manager settings Partition settings (if configured) Secure Manager settings (if configured) Network settings SNMP settings License settings Migrations are increasingly complicated and HP strongly recommends that any migration be performed by an HP Service engineer using ESL c01473045 and EML c01439962 migration documents. All migrations to the I270 and 2.8.00 code bundle must be preceded by upgrade to the I232 and 2.3.0 code bundle (migration instructions are included in the readme file for I232). CAUTION: Upgrading to 2.x is not supported for ESL9000 libraries. These libraries can be fully managed using Command View for Tape Libraries 2.x. but will not accept the I200 or higher Interface Manager code. ESL9000 libraries will work only with version I182 Interface Manager code and CVTL 2.6.00. Install the Interface Manager I274 release and 3.7.00 firmware bundle (EML and ESL E-Series Libraries) NOTE: You must be at the I232 and 2.32 firmware bundle or higher before proceeding with the upgrades to the I274 and 3.7.00 bundle. If at a revision lower than I232 or 2.32 firmware bundle first migrate to I232 and 2.32 firmware bundle to proceed. You must be at i250 and the 2.50 Frimware Bundle or above to download with Command View TL 3.0.00 or later. Installation instructions 9

NOTE: If the EML library is below 1200 download 1200 first. Then if the EML library is below 1407 download 1407 first. Otherwise the RLC might need to be replaced. Three EML library versions are included in the latest firmware bundle. 1. Save the existing configuration to a safe location before performing any Interface Manager upgrade. 2. Download and unpack the 3.7.00 EML or ESL E-Series firmware bundle and Interface Manager firmware I274 to the Command View for Tape Libraries client (for example, the desktop or laptop). Verify that the library, interface controller, drive (optional), and the Interface Manager firmware files are downloaded. 3. If your Interface Manager is at I232 or later, do not perform this step. Continue at the next step. This step tests the FTP session, and verifies that it can locate the files residing in the Interface Manager that need to be deleted. a. Create a text file with Notepad or WordPad and save it at test.txt. b. FTP to the Interface Manager as anonymous with no password. c. Enter put test.txt or copy the test.txt file to the Interface Manager. d. The ls, nlist, or dir command should indicate thattest.txt was just uploaded. If test.txt is not seen, then disable the firewall. FTP commands may not work correctly with certain firewalls (for example, Symantec Endpoint in Windows XP). e. Execute an ls, nlist, or dir command to verify that the directory does not have any entries. If it does, use the del <filename> command until all other files are removed. This will free up compact flash (CF) memory used by support tickets or saved configurations. If there is not enough CF memory, the Interface Manager migration might fail. NOTE: If you cannot see test.txt, stop downloading at this point or have a compact flash ready in case the download fails. 4. Use Command View for Tape Libraries to update the Interface Manager firmware. Follow the upgrade instructions to migrate directly to I274. 5. Use Command View for Tape Libraries to upgrade: to 5.9.63 firmware for the 2GB Fibre Channel Interface Controllers to 5.9.77 firmware for the 4Gb Fibre Channel Interface Controllers 6. Use Command View for Tape Libraries to upgrade ESL G3, ESL E-Series, EML E-Series library firmware. If the EML E-Series is below 1200, upgrade to 1200. If the EML E-Series library is below 1407, upgrade to 1407. The EML library firmware can now be update to the newer firmware. 7. Verify that all of the drives are empty. 8. Upgrade the drive firmware, if the drive firmware in the 3.7.00 bundle is newer than the drive firmware that is in your drives. 9. Save the new configuration to a safe location after performing any Interface Manager upgrade. Downgrading to previous releases Downgrading your Interface Manager to a previous release requires some special considerations: IMPORTANT: Remove any hardware that is not supported by the firmware release you are downgrading to. Failure to do so can cause the library to become inoperable. 10 Installation instructions

Multiple versions of the Command View for Tape Libraries software cannot be installed on the same computer at the same time. To use an older release of Command View for Tape Libraries, uninstall the current version before installing the older version. After performing the downgrade, you will need to restore system defaults through the restore system defaultscommand in the command line interface or through the Restore Factory Defaults page on the Support tab in Command View for Tape Libraries. CAUTION: All of your custom configuration information will be lost. If you have previously saved a configuration at the older release, you can easily restore this configuration after you have downgraded your Interface Manager through the restore system configcommand in the command line interface or through the Save / Restore page on the Configuration tab in Command View for Tape Libraries. Previous Version Enhancements Version 3.7.00 New features in Command View TL Administrator can manually select tapes in a separate media verification partition without interfering with host applications. Configurable policies permit periodic scans based on the time interval that you select. Support for Data verification and Drive Assessment in ESL G3 libraries for LTO5 and LTO6 drives and corresponding supported tapes. Support for managing media verification, configuration, and usage through CVTL while ensuring data security. Licensing enforcement and management for data verification license for ESL G3 libraries. MSL6480 license management through CVTL. User notifications of degraded tapes. Reports of data verification and drive assessment results. Library TapeAssure enhancements including the Library Dashboard with Library TapeAssure graphs. Support for RDC (Remote Data Collection) for ESL G3, MSL6480, and MSL G3 libraries. SMI-S implements the TapeAssure profile that can be collected by IRS RDC, and you can configure collection days for the RDC from the CVTL interface. Version 3.6.00 New features in Command View TL Command View TL Support for MSL6480 Library Support for unfiltered ESL G3 Health Events sent to Command View TL through SNMP Command View TL support for MSL G3 licenses TAA license support for MSL6480 Command View TL support on Windows Server 2012 Command View TL Support for Library TapeAssure (MSL G3/ESL G3/MSL 6480) Library TapeAssure overview Library usage Previous Version Enhancements 11

Version 3.5.00 Version 3.1.00 Version 3.0.1 Moves per library Empty slots per library New features in Command View TL Advanced TapeAssure Dashboard Predictive Analytics for tape drives and cartridges Alerts reporting Performance Advisor Drive Utilization Analysis Predictive Analytics for a tape drive health Predictive Analytics for a tape drive life Predictive Analytics for tape cartridge health Predictive Analytics for tape cartridge life Tape Cartridge Utilization and Performance Analysis Ability to save TapeAssure graphs and tabular data in PDF format Ability to email the TapeAssure graphs and tabular data in PDF format as an attachment License enforcement with Instant on capability for ESL G3, MSL, AutoLoaders NOTE: The features above are not visible or supported on EML and ESL E libraries. They must have an Advance Tape Assure Licence on each library to function. Ability to add and remove multiple libraries New features in Command View TL Added support for LTO-6 drives in EML and ESL G3 tape libraries. New features in Interface Manager firmware version I274 Added support for LTO-6 drives in EML tape libraries. Added service passwords valid through 02/01/2019. Modified the support ticket code for LTO 6 drives to use the drive s snapshot feature instead of individual SCSI commands. Supports ESL G3 dual robots and all ESL G3 Hardware Revision 2 configurations. New features in Interface Manager firmware version I273 Increased the encryption manager certificate key size from 1024 bits to 2048 bits. Added show station command to the CLI 12 Previous Version Enhancements

Version 3.0.00 GUI interface redesigned to enhance usability and scalability. Adobe Flash is now used instead of Java. Support for Insight Remote Support version 5.7, also known as WBES 6.3. Secure Manager host access is now configured using Access Control Groups for increased flexibility. Users now log in once to the management station, instead of repeatedly logging in each time a new library is managed. New features in Interface Manager firmware version I272 Version 2.8.00 New command to set SNMP traps from the CLI The CLI confirmation prompt can be skipped when mapping or unmapping hosts When using the CLI's show media or show mgmt log commands, the pause after every 20 items listed in now optional Updated the internal web server and SSH to newer versions for the Interface Manager. Because these use more memory than the older versions, if this is running on an original version Interface Manager board with 128MB RAM, it is highly recommended that the RAM be upgraded to 256MB RAM (HP part number 464581-001). Added a force option for CLI commands Map Host and Unmap Host. Added a no-prompt option for CLI commands Show Media and Show Mgmt Log. Added a CLI command that adds and removes SNMP traps. When manually adding hosts with the CLI command Create Host, additional parameter checking was added to prevent invalid entries. Added the LTO drive s IP address to the CLI command Show Drive Info. Added encryption status to the overall encryption health, and for each drive. Added LTO diagnostic pages 0x89, 0xBA, and 0xBB to internally-generated LTO support tickets. Improved robustness when loading new firmware to an EML library. Updated the encryption manager code to the newest version. Added support for ESL G3 Tape Libraries. Launching, Licensing and TapeAssure is fully supported through Command View TL. Other ESL G3 configuration is managed through the library's own GUI. Removed support for automatic discovery of libraries. Previous Version Fixes Version 3.7 Patch 2 Added a fix that sends alerts about certain Tape Alert 6 messages in the library event logs or RAS events caused by the error code 0x3339 (LF_ERR_UNABLE_TO_RELEASE). If this error is encountered, the following alert message is displayed: Previous Version Fixes 13

The drive (Serial Number) is reporting Tape Alert 6, the drive could not get the write data from the host. If the problem persists HP recommends checking the host and the host to drive SAN connectivity. Version 3.7 Patch 1 Fixed a data verification issue that reports Test has reported Pass and Incomplete (The test requires a tape to be loaded prior to it being run. Please load the tape to be verified and re-run the test). Version 3.7.00 Upgrade to Apache Tomcat 6.0.37. Fixed false alerts for multiple host encryption when host base is sending the keys. Version 3.6 Patch 1 The ESL-E capacity license does not work after upgrading Command View TL from 3.1.00 to 3.5.00 or 3.6.00. This only applies to ESL-e or EML libraries where capacity upgrades are present on one of the libraries managed by Command View for Tape Libraries. Version 3.6.00 The configurations to setup Multiple Email Address the coma separator did not work. Modified to a ; separator that now works. Version 3.5.00 Version 3.1.00 Command View TL installation will continue if any version of PostGreSQL is already installed by any application. The cabling view for ESL-E and EML were showing the robot link connection is down when the robot does not have a link connection. Postgre would not install, non English Windows OS "users" group is different word. Upgraded to Apache server 6.0.35. Fixed an issue that occurs in multiple session instances where an added host is edited in one session causing the host to be shifted in the other session. Fixes in Interface Manager firmware version I274 Rebooting the Interface Manager after turning the auto support ticket feature on or off from the CLI is no longer required. The CLI session is no longer terminated if out-of-range port numbers are given for the CLI command Set Interface Hostport. An error message is now displayed. Fixed an issue so that It is now possible to set IPV6 destinations for SNMP traps. This can be done through the CLI command Set Net Snmptrap or through the CVTL GUI with the SNMP Alerts settings Removed the site command from the CLI command show system contact, since it was using the same database entry as the location command. Other parts of the CLI only have the location command. Fixed an issue where library power-on SCSI Unit Attentions are no longer recorded in library support tickets (ALM 220). Fixed an issue so that It is now possible to specify the name of the configuration file when performing a Restore System Config command from the CLI. 14 Previous Version Fixes

Version 3.0.1 Fixed an issue so that if a drive reboot fails during a Restore Defaults the Interface Manager will still be rebooted Fixed an issue where Show Drive Info IP now correctly displays drive numbers for drive numbers 10 and above. Modified the support ticket code for LTO 6 drives to use the drive s snapshot feature, rather than individual SCSI commands Fixes in Interface Manager firmware version I273 Updated the SNMP server to a much newer version. This fixes all known SNMP-related memory leaks. To reduce memory consumption, the SNMP log file /var/log/snmpd.log is no longer created. When updating to I273 firmware and later, if the files /var/log/snmpd.log and/or lastlog.log are present, they will be automatically removed. Fixed issue where the Interface Controllers FRU Wizard would not always process all new Interface Controllers, and could unexpectedly move the SIPP master. Fixed the drive sort order for the Show Host Access CLI command. Changed the reporting process when errors occur during encryption enrollment to a SKM/ESKM. Now, if there is any error, the status will show that encryption is not enabled. Fixed an issue where EML libraries could turn on Ethernet Broadcasting after a Restore System Defaults. If custom LUN mappings are selected when configuring host access, and an Interface Controllers is started with a LUN number near 127, auto-populated LUNs will wrap to zero after reaching 127. Fixed an issue where if a directory in the Interface Manager that normally contains optional scripts becomes corrupted, the directory will automatically be cleaned up when an Interface Manager code update is performed. Fixed the column alignment when running the CLI command show mgmt log event. Version 3.0.00 Fixed an issue where licenses could show up in the Un-managed Licenses section of the License Key Summary tab. Generated support ticket details can now be viewed in the browser. Fixes in Interface Manager firmware version I272 Fixes for numerous CLI formatting errors. Fixed a potential issue where a Failed to Migrate Drive error could be reported when using the Drive Update Wizard to migrate a LTO1, LTO2, or LTO3 drive to a LTO4 or LTO5 drive. The error was most likely to occur on a partitioned library. Corrected handling of the restore config operation. Now, a config file created up to two major revisions prior to the current firmware can be restored. Fixed an issue where collecting a support ticket from an LTO3 drive could result in a blank ticket. Fixed an issue so that it is no longer possible to assign 192.168.2.xxx IP addresses to EML libraries; this IP address range is not compatible with hardware in an EML library. Fixed an issue so it is no longer possible to set the IP broadcast address on EML libraries. Fixed an issue where switching between IPV6 and IPV4 in a single operation, on an EML library, the OCP would not show the IPV4 address. Previous Version Fixes 15

When a SNMP Trap String is modified in the CVTL GUI, the new Trap String now takes effect immediately. SNMP read requests to unsupported MIB identifiers no longer cause the SNMP log file to grow. SNMP reads of the standard system MIB now return correct values for host name, system location, and contact. The CLI command Show Library Topology now reports correct drive information. ESL libraries will now automatically trigger cleaning tape tickets. ESL and EML event codes are now sent as SNMP Traps, for Remote Support. When performing a manual migration from a SKM encryption server to an eskm encryption server, performing a Validate SKM Connectivity operation will update the displayed key manager type. Version 2.8.00 Command View TL no longer calculates read margins on small transfer sizes because the data is not accurate. Command View TL now requires Java Runtime Environment (JRE) version 1.6.0, Update 24, also known as 6.0. The TapeAssure Overview page now shows the following message for libraries that are I250 or lower: The libraries need a firmware upgrade to be TapeAssure compatible... Fixed an issue on the Command View TL Launcher where the ESL Library had an EML name and serial number. Fixed an issue on the Tape Properties page where the Drive Serial Number was labeled as the Library Serial Number. Fixed a case when Command View TL was not displaying drive support tickets if a cleaning tape was in the drive. Workarounds Data verification test was not able to complete for the currently selected tape cartridge Symptom: Due to intermittent network connection problems, the data verification test was not able to complete for the currently selected tape cartridge. Workaround: Before starting Full data verification tests, ensure that applications which need extensive network bandwidth are not running at the same time. Try to verify the media at a different time when the network traffic may be lower. If the error persists on a Full test, retry the test in Quick/Intermediate test mode. For more information, see Data verification issues section in Troubleshooting chapter of HP StoreEver Interface Manager and Command View for Tape Libraries Version 3.8.00 User Guide. Found in version: 3.7.00 and later Data verification job in an incomplete state Symptom: If the barcode is longer than eight characters, during data verification the barcode gets truncated due to which the cartridge gets stuck in the drive. Workaround: 16 Workarounds

NOTE: HP tape libraries and associated application software like HP CVTL, HP Data Protector, and other backup applications support eight character bar code labels. HP recommends the usage of eight character bar code labels for compatibility with other libraries and other applications. Do not use barcode characters with length greater than 12 characters while using Data Verification or Tape Assure Advanced functionalities/features. To resolve this issue, perform the following: Unload the cartridge from the drive and move the cartridge to a user partition. Restart the data verification engine. Found in version: 3.8.00 Consecutive Data Verification results are marked with Test Incomplete status Symptom: When Data Verification is performed using drive(s) which are not in a responsive state, the Data Verification results are displayed as Test Incomplete. Workaround: This issue may be observed with Data Verification on an ESL G3 library. To resolve this issue, take note of the Overall System Status display on the ESL G3 Library Management Console (LMC) or front panel and make sure that all subsystems have a green (Good) status. If any subsystems have a yellow (Warning) or red (Critical) status, please follow the respective RAS resolution steps to resolve those issues. After resolving any outstanding RAS events, take note of the Monitor > Drives menu and make sure that all drives within the Data Verification partition are in a good state. If the issue persists, contact HP support. Coexistence of LTT and CVTL issue Symptom: When CVTL and LTT are launched together on the same browser, CVTL launches with an error. Workaround: Use separate browsers for CVTL and LTT applications to avoid flex related issues. Found in version: 3.7.00 Launch CVTL and navigate to Administration page Symptom: The Web server port and Email size limit fields on the Administration tab are displayed as -1. Workaround 1: 1. Select Start Menu+Run. Enter Services.msc and click OK. 2. Stop the HP Library and Tape Tools WebGUI service. 3. Stop the Command View TL service. 4. Start the Command View TL service. 5. Start the HP Library and Tape Tools WebGUI service. Workaround 2: 1. Uninstall Command View TL 3.6.00. 2. Uninstall the Library and Tape Tools WebGUI 5.0. 3. Install Command View TL 3.6.00. 4. Install the Library and Tape Tools WebGUI 5.0. Found in version: 3.6.00 Installing Command View TL shows PORT# 5450 is in use by another application message Symptom: During the installation, the following message is displayed: PORT# 5450 is in use by another application. Workarounds 17

Installation will abort. Please ensure PORT# 5450 is free and retry the installation. Workaround: Ensure the PORT# 5450 is free and try re-installing Command View TL. If the PORT# 5450 is blocked by your firewall, configure the firewall to allow communications through PORT# 5450. If the PORT# 5450 is used by another application, free it from the other application or install Command View TL on a different server. Found in version: 3.5.00 Unable to launch <Newly selected Command View TL destination folder>\bin\wrapper.exe. error is received Symptom: During the 3.5.00 upgrade, the error message Unable to launch <Newly selected Command View TL destination folder>\bin\wrapper.exe. is displayed in a dialog box. Workaround: Click Ok in the dialog box. The Command View TL upgrade will continue for few minutes and then an Installshield wizard complete dialog box is displayed; click Finish in the dialog box to complete the installation. Found in version: 3.5.00 Uninstalling Command View TL by retaining support tickets, backup files and Installing the Command View TL in a different location does not copy the support tickets, backup files to the new location Symptom: You cannot view the details of the support ticket when double clicking it from support ticket panel. TapeAssure backup files will not be listed in TapeAssure Save/Restore Database panel. Workaround: 1. Copy the files From <previously installed Command View TL location>\supportticket\ v2 To <newly installed Command View TL location>\ supportticket\v2 2. Copy the files From <previously installed Command View TL location>\tapeassurebackup To <newly installed Command View TL location>\tapeassurebackup TapeAssure data is not shown for ESL-E, ESL G3, MSL and Autoloader drives Symptom: In rare cases, TapeAssure data is not shown for a very few number of ESL-E, ESL G3, MSL and Autoloader drives. Workaround: None. This issue will be addressed in a future release. Found in version: 3.5.00 After doing a FRU replacement of an Interface Controller with no drives attached might not come back to a green state Symptom: The Interface Controller has the maps pushed to it but the Interface Manager has missed that this has happed. Workaround: Telnet to the Interface Manager and run the show host access refresh. This command causes the Interface Manger to get mapping and host access information up to date. If for some reason this does not work rebooting the Interface Manager or Interface Controller should also work. Found in version: i274 and lower 18 Workarounds

On an Encrypted library after doing a FRU replacement of LTO5 or LTO6 drives the library might present an error against the LTO5 or LTO6 drives as "Unable to open management path" Symptom: The encryption path to the LTO5 or LTO6 drives IP address of the drive just removed is not removed from the data base in the IM. Workaround: Rebooting the Interface Manager will clean up the IP address for the encryption path. Found in version: i274 and lower ESL-E libraries with LTO3 drives can hang during unload Symptom: The ESL-e library takes 1 hour and 15 minutes to do a move command but the LTO3 drive will not unload and gets the error Tape move for tape with barcode AA[xxxx] failed 020b800b Command aborted by user. The LTO3 drive and the ESL-e library are hung and a library reboot is required to recover. The ESL-e retry on the drive unload, the host software sending a load command and the Interface Manger sending the support ticket at the same time is causing the LTO3 drive to hang. Workaround: Back revision only the Interface Manager code to I270. If I274 is required for a different issue then in the Interface Manger CLI send the command set support disable can be used but this will disable tape assure. Found in version: i271 and later Interface Manager Firmware will not let it be chosen in the download list Symptom: Occasionally if multiple files are chosen to be downloaded the Interface Manager firmware will not show up in the list to check. Workaround: Go back to the previous page and wait about 20 seconds. Then click on next again. Found in version: 3.1.00 Interface manager is yellow Secure Manager needs to be synchronized Symptom: Secure Manager inoperative - One or more interface controller device map(s) are out of synchronization with the access control settings. Please run the "Synchronize" action available on the Secure Manager page face controller device map(s) are out of synchronization with the access control settings. Please run the "Synchronize" action available on the Secure Manager page. Workaround: Manually run the Sync Sec from a ssh or telnet session to the IM. If this fails, reboot the component that the WWN is listed as belonging to then do a resynchronize before calling support. Found in version: I270 and later Command View TL user interface is unresponsive Symptom: After selecting Host Access Actions Add Access Control Group (for an EML and ESL E-Series library), the Command View TL user interface becomes unresponsive. Workaround: Close the browser window and manage the library again. Found in version: 3.0.00 Restoring the configuration of the library does not reflect the restored configuration Symptom: Restoring the configuration of the library from the Interface Manager CLI does not reflect the restored configuration in the Command View GUI. Workaround: After restoring the configuration of the library from Interface Manager CLI, manage the library using the Command View TL GUI, then navigate to the pages in configuration pane and click Refresh. Found in version: 3.0.00 Workarounds 19

Command View TL 3.0.00 upgrade libraries with i240 code of earlier Symptom: The firmware downloads will fail, hang or timeout even if connectivity passes. Workaround: CVTL 3.0.00 cannot upgrade any libraries with i240 or older Interface Manager firmware. Use 2.7.00 or 2.8.00 versions of command view TL to upgrade the Interface Manager firmware or use the cli method to update the Interface Manager code first to i270 or greater. Found in version: 3.0.00 Command View TL 3.0.00 upgrade libraries with i240 code of earlier Symptom: On a Windows 7 Operating System with the Power Options mode set to turn off the display or put the system to sleep the following error can occur when accessing the system after it has turned off the display or gone into sleep mode. Deteched duplicate HTTP-based FlexSession, generally due to the remote host disabling session cookies. Session cookies must be enabled to manage the client connection correctly." Workaround: Refresh the Command View TL and login again, or relaunch Command View TL. Found in version: 3.0.00 Support ticket.zip files do not have the service.log file for the management station Symptom: Support ticket.zip files do not have the service.log file for the management station Workaround: To view the service.log file, Launch Command View TL and manage the library. 1. On the left pane, navigate to Support tab. 2. Go to Action Save Management Station Log as... and save the.zip file. By default the file name will be mslogs.zip. 3. Extract the mslogs.zip from the saved location. The service.log for the management station will be available. Found in version: 3.0.00 Date/Time are incorrect after Daylight Savings Time (DST) change Symptom: Libraries that are not configured with Network Time Protocal (NTP), the date/time is wrong after the Daylight Saving Time (DST) flipover. Workaround: On the libraries that are not configured with Network Time Protocal (NTP), Daylight Saving Time (DST) has to be applied manually. Found in version: 2.7.00 or later Secure Manager cannot communicate with the robotics, access control changes cannot be made Symptom: ERROR: cannot communicate with the Robotics communication must be established before Host Access configuration can occur. is displayed in the host access node under the configuration tab. This occurs when a configuration file is restored to the library, and the interface controller currently hosting the robot LUN is different from the interface controller that is specified to perform this task in the configuration file. Workaround: Reboot the interface manager to clear the problem. Avoid this error by saving a new configuration file after any configuration change on the library. Found in version: 2.7.00 or later The command line interface can disappear immediately after passwords are entered Symptom: The command line interface can disappear immediately after passwords are entered. 20 Workarounds

Workaround: This is caused by logging into the Interface Manager before it is ready. Wait a few seconds, then log in again. Found in version: I270 or later Postgre database install failure Symptom: When installing Command View TL, the installer might display Setup could not create the cvtl_db database. Workaround: Contact HP Support. Found in version: 2.8.00 or later Interface Manager database malformed Symptom: The error An error occurred while updating data. Please retry the operation. is followed by SQLite error 11: database disk image is malformed. Workaround: Contact HP Support. Found in version: 2.8.00 or later LTO3 cleaning cartridge information is not saved Symptom: Most LTO3 drives are unable to save cleaning cartridge information. The LTO3 drive hardware revision that is capable of saving cleaning cartridge information may be identified by a firmware revision starting with "U". Workaround: Install an LTO3 drive with a firmware revision that begins with U. Found in version: 2.8.00 or later After a firmware download, the 8 Gb Fibre Channel link disconnects Symptom: After downloading firmware to a drive, some switches will lose the link to the drive. Workaround: Make sure that your 8Gb Fibre Channel switch has the latest firmware, as recent switch fixes have been introduced. If the problem persists, either 1) reboot the drive again with Command View TL, or 2) unplug the fibre channel cable at the switch, then plug it back in. Found in version: 2.8.00 or later Modifying system network card configuration causes NOT BOUND IN REGISTRY errors Symptom: On the management station, if you disable the active network card and enable a different network card, Command View TL will display NOT BOUND IN REGISTRY errors. Workaround: Restart the Command View TL service after the network cards have been altered. Found in version: 2.8.00 or later Secure Manager will not synchronize when there are more than 255 hosts Symptom: If there are more than 225 stale hosts hosts that were on the SAN at one point, but are no longer present Secure Manager can not synchronize. Workaround: Reboot any LTO4 and LTO5 devices in the library. Found in version: 2.8.00 or later The operation restore system defaults fails when restoring advanced LTO drives Symptom: When restoring an advanced LTO tape drive (LTO4 or LTO5), the operation restore system defaults might fail. Workaround: Retry the operation. If it fails a second time, contact HP support. Workarounds 21

Found in version: 2.8.00 or later Command View for Tape Libraries indicates that TapeAssure is disabled or not collecting for some libraries Symptom: EML and ESL E-Series Tape Libraries shipped before November 2007 may require a RAM upgrade in order to be TapeAssure capable. Without sufficient RAM on the Interface Manager card, TapeAssure will be disabled Workaround: A customer-installable RAM upgrade can be ordered as HP part number 464581-001 from the HP Parts Store (http://www.hp.com/buy/parts) or PartSurfer (http://partsurfer.hp.com). After replacing the part using the included instructions, remove and re-add the library on the Command View for Tape Libraries Launcher screen Found in version: 2.8.00 or later A drive reboot fails when initiated from Command View for Tape Libraries or the Interface Manager command line interface Symptom: After initiating a drive reboot operation, a Command View TL user interface or command line interface error appears, and the drive is left in a 'yellow' or 'red' health state. Workaround: Try the reboot operation again, either from the Command View TL user interface, the command line interface, or the library Operator Control Panel. If the retry does not succeed, reboot the Interface Manager card to force a rediscovery of all drives. A reboot of the entire library will also clear the symptom, but is rarely necessary. Found in version: 2.8.00 or later Firewall considerations for the HP Secure Key Manager and HP Enterprise Secure Key Manager Symptom: The Firewall prevents communication with an HP Secure Key Manager (SKM) and HP Enterprise Secure Key Manger (ESKM) appliance. Workaround: The following network ports are the recommended ports to be used by an HP SKM and ESKM appliance to communicate with an Interface Manager, or with the SKM or ESKM management user interface, or for SKM and ESKM communication to other devices. All ports are TCP and SSL capable. 22 (SSH login to SKM or ESKM) bidirectional 161 (SNMP from SKM or ESKM) bidirectional 9000 (Interface Manager login to SKM or ESKM) bidirectional 9081 (FIPS status server from SKM or ESKM) bidirectional 9001 (SKM or ESKMnetworking) bidirectional 9443 (Web login to SKM or ESKM) bidirectional Found in version: 2.8.00 or later Firewall configuration rules Symptom: The Management Station cannot communicate with the web browser (Command View for Tape Libraries). Workaround: The following network ports are used by the Management Station to communicate with the web browser (Command View for Tape Libraries): 4093-4095 (TCP) bidirectional 2715 (TCP and UDP) outbound in CVTL 2.8.00 or lower 22 Workarounds

The following network port is used by the Management Station to communicate with the Command View TL database: 5450 (TCP) bidirectional (required for CVTL 3.5.00) By configuring your firewall with respect to Management Station to allow communication through these ports, the web browser you use to run Command View for Tape Libraries can be on the other side of a firewall from your Management Station. The following network ports are used by the Management Station to communicate with the Interface Manager: 8098 (TCP) bidirectional in CVTL 2.8.00 or lower 8099 (TCP) inbound 18098 (TCP SSL) outbound By configuring your firewall to allow communication through these ports, the Management Station can be on the other side of a firewall from your library. The Interface Manager requires the following ports to be open on the Management Station: 22 (TCP) inbound, SSH Access for CLI usage 25 (TCP) outbound, SMTP email client 53 (UDP+TCP) outbound, DNS client mode 67-68 (UDP) outbound, DHCP client 123 (TCP and UDP) bidirectional, to communicate with the NTP server 161 (UDP) bidirectional, to communicate with the SNMP trap server MSL G3 libraries require the following ports to be open on the Management Station: 22 (TCP) inbound, for service and future diagnostic functions. This port can be disabled by the admin if they choose. 80 (TCP) bidirectional, HTTP library is a webserver for administration purposes 161 (UDP) bidirectional, required to communicate with the ESL G3 library 162-169 (UDP) inbound, one port in the range required to receive the SNMP traps 427 (UDP+TCP ) bidirectional, SLP Service Locator Protocol 443 (TCP) inbound, HTTPS Secure Webserver 5696 (TCP) outbound, KMIP communication port on the server. Library uses a non privileged port. ESL G3 libraries require the following ports to be open on the Management Station: 22 (TCP) inbound, SSH Access for CLI usage 25 (TCP) outbound, SMTP email client 53 (UDP+TCP) outbound, DNS client mode 67-68 (UDP) outbound, DHCP client 123 (TCP and UDP) bidirectional, to communicate with the NTP server 161 (UDP) bidirectional, to communicate with the SNMP trap server 80 (TCP) bidirectional, HTTP library is a webserver for administration purposes 161 (UDP) bidirectional, required to communicate with the ESL G3 library 162-169 (UDP) inbound, one port in the range required to receive the SNMP traps 389 (TCP) outbound, LDAP non-secure LDAP client 427 (UDP+TCP ) bidirectional, SLP Service Locator Protocol Workarounds 23