Remote Terminal Unit ER1000 ERL with more than three decades of expertise in Power System Protection have developed state of the art Automation Solutions. The whole family of ERL s Remote Terminal Unit (RTU) and Feeder Remote Terminal Unit (FRTU) covers a broad spectrum of use with products of different sizes for various applications. The ER1000 is specifically architected for use with medium to large numbers of data points, and is well suited across a range of power system applications. ER 1000 Remote Terminal Unit (RTU), the building block of ERL Substation Automation system is designed to meet the present day utility and industry demands. The RTU is built on internationally well proven hardware and software platform. The standard hardware platform gives the necessary ruggedness and the RTOS (Real-Time Operating System) provides the multi-tasking and Real-Time data handling capability. This makes the ER 1000 the state of the art Automation Product of the 21st century APPLICATION ü Gateway for communication between IEDs and Master station. ü Data concentrator for storing data from the IEDs and transferring it to master station. ü Automation unit for building soft logic. ü Station level RTU for hardwired inputs. Add on serial I/O s (RS232 / RS485 software configurable). Add on parallel I/Os (DI, DO, AI, RTD, AO counters etc) High Speed Back Plane Architecture. Equipped with Real-Time Operating System. Equipped with various industrial protocol stacks both at Bay level and Station level. Highly modular in hardware and software design. Redundancy in CPU / Power Supply / Communication Port available. User friendly Configuration Tools for ease of Configuration and Management. FEATURES Flexible soft logic programing 32-bit High performance RISC (Reduced Instruction Set Computing) operating at >80 MHz Core Frequency. Memory SRAM (64Kbytes Internal and 2MB External) FLASH (512Kbytes). On board 10/100 Mbps Fast Ethernet Controller. On board 6 serial I/Os (RS232 and RS485) and 1 Debug Port.
HARDWARE: The Major Hardware Components are 1. Central Processing Unit. 2. Digital Input Module 3. Digital Output Module 4. Analog Input Module 5. Analog Output Module 6. Power Supply Module 7. High Speed Back Plane Serial I/O Module Apart from 6 no of Serial I/O supported by CPU additional serial I/O card (each card supporting 8 no s of RS232 / 485 Software configurable) expansion is possible. Digital Input Module Central Processing Unit 16 Opto Isolated Channels supporting direct field input voltages of 24 / 48 / 110 / 220 VDC. Software Programmable Debounce Timers. Protection against reverse polarity. 1 common for a group of 8 channels. LED indication for each channels for identification of healthiness of field signal and also separate card healthiness indication. The design incorporates dedicated processors to manage the time critical intensive Real-Time process involved in computer control and monitoring environment. (Cold Fire core Processor delivering 76 MIPS at 80 MHz running from internal flash memory with Enhanced Multiply Accumulate (MAC) Unit and hardware divider). The dedicated communication processor provides Real-Time exchange between IEDs of multiple protocols to SCADA systems. The CPU has on board Ethernet port and multiple serial ports and Memory Module. CPU healthiness, Communication Indications etc are provided for easy diagnosis. CPU card supports 6 Serial (2 X RS232, 1 X RS485, 2 X RS232/RS485, 1No. of X RS232 debug port), 1No. of 10/100 Mbps Fast Ethernet and high precision IRIG-B interface for Time Synchronization. On board GPS receiver is supported as an optional feature. Digital Output Module:
16 Single pole relays with one normally open (NO) contact. 8 single pole relays with 1 common. Supports wide range of Inputs such as 24 / 48 / 110 / 220 VDC. Power supply healthy Indication is provided on the Facia. NO and NC contact are provided for alarm Indication. The digital outputs can be configured for single / double / set point outputs on the same module. Rated Current 8A and Breaking Capacity of 2000VA. Rack & Back Plane Analog Input Module 16 Isolated Analog Channels for Measuring Current and Voltages. Both Unipolar and Bipolar Configuration supported for a single card type. Current Range Supported are +/- 20, +/- 10, 0-20 and 4-20 mamp. Voltage Range Supported are +/- 5V, +/- 10V. Power Supply Module The Rack is provided with a high speed intelligent back plane and supports Slot Concept (any card at any slot). Backplane design supports redundancy of CPU and Power Supply modules. Rack and back planes are available in different sizes of 4U 19 and 4U 19/2 (inches) with flush mount arrangement. SOFTWARE Communication Protocol Standard IED Protocols IEC 60870-5-103 Master (Serial) IEC 60870-5-101 Master (Serial) IEC 60870-5-104 Master (TCP/IP) Modbus Master (RTU Serial) IEC 61850 Client (Optional) Standard SCADA Protocols IEC 60870-5-101 Slave (Serial) IEC 60870-5-104 Slave (TCP/IP) DNP 3.0 Slave (Serial and TCP/IP) IEC 61850 Server (Optional)
Standard Time Synchronization Protocols IRIG-B (BNC Connector Amplitude Modulated) Simple Network Time Protocol SCADA Protocol Based (IEC 101 / 104, DNP 3.0 Slaves). A wide range of communication media is supported with options such as: Leased line modem Dial-up PSTN modem CDMA/GPRS/GSM modules Fiber optic interface Interface for connection to PLC s radios, satellite, etc. Reliability Since the Remote Terminal Unit is the component of a SCADA/control system exposed to the most severe environmental conditions, reliability has been a key consideration throughout the development of ER1000. The unit is self-monitoring and in the unlikely event of a malfunction, this is reported to the master station at the first possible opportunity. Modular architecture for performance and flexibility The ER1000 has a modular design of both hardware and software. It can be equipped with input & output modules and power supply circuitry to match the specific requirements of each application. RTU CAPACITY Single rack supporting up to 208 I/O s. Multiple rack expansion supported over Ethernet. Up to Five racks can be stacked for better performance supporting 1040 I/O s. Up to 16 IEDs on Legacy RS485 bus for optimum performance. 1000 SOE record storage is supported in chronological order. +/- 1 msec I/O scanning resolution and time stamping. Easy Commissioning and Maintenance Tools ER1000 is as easy to use, as it is flexible. Installation is quick and uncomplicated also commissioning and testing is likewise simple. Parameter setting and testing The software used for parameter setting / configuration of the ER1000 is based on easy to understand menus and features extensive help manual. Protocol permitting, parameterization can also be done by down loading files from the central station (LAN / WAN). The tools make it possible to test the RTU locally / remotely (Ethernet based Config Tool) to diagnose malfunctions, confirm the configuration or check process connections.
Maintenance The ruggedness and reliability of the ER1000 make it maintenance free and requires no further attention once installed. ENVIRONMENTAL COMPLIANCE ER 1000 has been designed to meet the requirements for environmental conditions and performance of Remote terminal Unit and is type tested to the following standards IEC-60810-2-1 LEVEL 3 DAMPED OSCILLATORY MAGNETIC FIELD POWER FREQUENCY MAGNETIC FIELD POWER FRFQUENCY WITHSTAND TEST PULSE MAGENTIC FILELD 1.2/50 IMPULSE VOLTAGE TEST INSULATION RESISTANCE CLOD TEST DRY HEAT TEST DAMP HEAT TEST HIGH VOLTAGE TEST IEC-60255-5 IEC-61000-4-9 IEC-60255-5 IEC-60068-2-1 IEC-60068-2-2 IEC-60068-2-3 MFG SPEC LEVEL 3-4 LEVEL 4 LEVEL 3 LEVEL 3 LEVEL 3 2 KV FOR 1 MIN LEVEL 5 2 KV >100M0hm 0 0-10 &-25 C FOR 2 HRS 0 +55 C FOR 72 HRS AND + 0 70 C FOR 2 HRS 0 95 % RH @40 C FOR 96 HRS 300VAC
Guaranteed Technical Particulars
Ordering Code: FACT/ER1000/05-11/REV.2 " Easunreyrolle- ERL, the ERL Logo and any alternative version thereof are registered trademarks and service marks of Easun Reyrolle".