Tranquil T7-HSA Harmony Home Server Protect Connect Organise Grow Iss1.0
Thank you for purchasing the Tranquil Harmony Home Server This appliance, if cared for and used correctly will provide many years of service. Reading through all of these simple instructions will reduce any potential setup problems. Index Introduction.. Page 2 Contents.. Page 3 Planning your installation... Page 3 Wiring up the T7-HSA. Page 3 Turning On. Page 5 Install the Windows Home Server Connector Software Page 6 User Accounts. Page 6 Shared Folders... Page 7 Computer Backups.. Page 8 Server Storage. Page 8 Windows Home Server Settings. Page 9 More Information. Page 10 Troubleshooting. Page 10 Securing your Harmony Home Server. Page 11 Protecting your System. Page 11 Restoring your system... Page 11 Specification.. Page 12 Introduction The Tranquil Harmony Home Server is a small, low power, near silent appliance that will provide enhancements and security to you digital home information. The unit, is designed for 24/7 operation. You will now be able to backup all of your connected PCs, expand your own storage, create shares for common digital files, ie music and pictures, duplicate your important files for security, share and access your files via the internet and even remotely control your connected PCs. 2
Contents 1. T7-HSA Home Server unit (incl hard disk HDD) 2. 80W AC/DC power adapter 3. Mains cord (country specific) 4. System recovery kit (Jewel case) 5. Windows Home Server DVD (full restore) 6. Windows Home Server Connect CD 7. Windows Home Server Recovery CD 8. Power loom for 12V USB HDDs Please check all of the contents are present before proceeding to use your appliance. Planning your installation The T7-HSA is a fan less device and relies of natural air convention to keep it operating correctly. Do not put it in a sealed environment, ie a cupboard. Ideally it should be located in open space, ie a desk, shelf etc. You will need a near-by mains power outlet, and a wired LAN (Ethernet) connection to the router too. The unit case temperature does rise in normal operation and it will be warm to the touch. The maximum ambient room temperature should not exceed 37 C, for optimal operation. The unit should always be operated in a vertical mode. Do not cover the unit. Wiring up the unit On the next page you will see how to connect the unit. The basic connections required are Power In, and Ethernet (LAN). It is strongly recommended that at least one additional external hard disk (USB HDD) is connected promptly, to ensure that data duplication can be operational, and your folders protected from hardware failure. If you have 12V DC USB HDD units ie Iomega, Western Digital (My Book), etc. with a 2.1 or 2.5 mm power connector you can power these devices from the Power Out port. The unit will support and provide power for up to four external USB HDD devices. 3
Wiring up 4
Turning on Once the unit is installed in a suitable location, and connected to your local area network (LAN). You are ready to turn it on. Applying power (12vDC) will turn the unit on, if you need to manually turn the unit on or off you can use the small round power switch on the front panel, next to the blue light (unit on) The unit does not have a keyboard/mouse/screen, and the only indication you will have the unit it operating is : 1. BLUE power light will be illuminated 2. The RED hard disk activity light will flash occasionally 3. LAN activity lights will illuminate to indicate LAN connected and LAN activity You may also hear a very slight hum from the internal hard disk, if you listen closely. In the event of a power failure (power cut), the unit will power up automatically, once the power resumes. You can now proceed to install the Connect software on each of your connected PCs. It is through the connect software console that the Harmony Home Server is setup and managed.. 5
Install the Windows Home Server Connector Software The Windows Home Server Connector software does the following: Connects your home computer to Windows Home Server. Automatically backs up your home computer nightly. Monitors the health of your home computer. Enables you to configure and remotely administer Windows Home Server from your home computer. To install the Windows Home Server Connector software 1. Insert the Windows Home Server Connector CD into a computer that is connected to your home network. The Windows Home Server Connector Wizard starts. 2. Complete the wizard to connect your computer to Windows Home Server. Run the Windows Home Server Connector Wizard on all of your other home computers to connect them to Windows Home Server. Run the wizard on one computer at a time. The logon password for your SERVER is ServerServer1 Note If you do not have your Connector CD, you can install the Connector software from the Software shared folder on Windows Home Server. The following are tasks that you can do as soon as Windows Home Server is set up and your home computers are connected. User accounts Shared folders Computer backups Server storage Windows Home Server Settings console to open the Windows Home Server Console Help User Accounts After you complete Windows Home Server Setup and install the Windows Home Server Connector software on all of your home computers, you are ready to add user accounts for the people in your household. User accounts are required in order to control access to the shared folders on Windows Home Server. Windows Home Server tray icon, and then click Windows Home Server Console. 6
To add a user account 1. From a home computer, right-click the Home server Icon in the system tray, then click Home Server console. 2. Type the Windows Home Server password (Default = ServerServer1), and then click Next. 3. On the Windows Home Server Console, click the User Accounts tab. 4. Click Add, and then complete the Add User Account Wizard. 5. Repeat for each user account that you want to add. Note When you create user accounts on Windows Home Server, use logon names that match the logon names of your existing user accounts on your home computers. Also, use the same password that you use for your existing user accounts. This makes it easier to access shared folders on Windows Home Server. If the user accounts and passwords do not match, you will be prompted for a user name and a password when you open Windows Home Server shared folders. Shared Folders Shared folders are places for you to organize and store them with other people on your home network. The following shared folders are created automatically on Windows Home Server: Photos Music Videos Software Public A personal shared folder for each user account. You can easily add more shared folders to meet your needs To add a shared folder 1. From the Windows Home Server Console, click the Shared Folders tab. 2. Click Add. 3. Complete the Add a Shared Folder Wizard. Note A personal shared folder is created each time you add a new user account by using the Add User Account Wizard. By default, only this user account has access to in this personal shared folder. 7
Computer Backups By default, all of the hard-drive volumes on each home computer are backed up every night after you install the Windows Home Server Connector software. You can customize the backup of each of your home computers from the Windows Home Server Console. To customize a home-computer backup 1. From the Windows Home Server Console, click the Computers & Backup tab. 2. Right-click the computer that you want to customize, and then click Customize Backup. 3. Choose hard-drive volumes to back up and to exclude folders from the backup. Server Storage If you want to add more storage to Windows Home Server, you can add external USB 2.0 hard drives by using the Server Storage tab on the Windows Home Server Console. Caution Your hard drive will be formatted when it is added to your server storage. Make sure that you copy any adding it to your server storage. Important If you add an external USB hard drive, use a USB 2.0 hard drive. Using USB 1.1 devices can cause poor performance and unpredictable results. To add a hard drive 1. Connect the USB hard drive and power it on 2. From the Windows Home Server Console, click the Server Storage tab. 3. Under Non Storage Hard Drives, right-click the new hard drive, and then click Add. 4. Complete the Add a Hard Drive Wizard to format the hard drive and to add it to your server storage. Caution If you want to permanently remove an external hard drive from your home server, use Remove on the console Server Storage tab. Right-click the hard drive that you want to remove, and then click Remove so off of the hard drive before you disconnect it. 8
Windows Home Server Settings Click Settings on the Windows Home Server Console to open the Windows Home Server Settings dialog box: You can use Windows Home Server Settings to General Configure the date and time. Configure the regional settings. Configure Windows Update. Configure Customer Experience Improvement Program. Configure Windows error reporting. Backup Configure the Backup Time. Configure Automatic Backup Management. Run Backup Cleanup. Passwords Change the Windows Home Server password. Configure the User Accounts Password Policy. Media Sharing and Videos shared folders, so that you can stream digital media from Windows Home Server to a device that supports Windows Media Connect. Remote Access Configure Web site connectivity. Configure your broadband router. Configure your domain name. Configure the settings for your Windows Home Server Web site. Add-ins Install and uninstall Windows Home Server Add-ins. Resources Activate Windows Home Server. View hardware information about your home server. View Windows Home Server version information. Learn more about Windows Home Server. Connect to the Windows Home Server Community Contact Product Support. In addition, you can shut down Windows Home Server from the Settings dialog box by clicking Shut Down. For more information about Windows Home Server Settings, click Help on the Settings dialog box. 9
More Information You can get more information about Windows Home Server from the following locations: Click Help on the Windows Home Server Console to open Windows Home Server Console Help. On a home computer, right-click the Windows Home Server task tray icon, and then click Help to open Windows Home Server Help. For more information about Windows Home Server documentation, see the Microsoft Web site (http://go.microsoft.com/fwlink/?linkid=85098). To share ideas and information with other Windows Home Server enthusiasts, see the Windows Home Server Community Forums Web site (http://go.microsoft.com/ fwlink/?linkid=83211). To research troubleshooting tips, see the Microsoft Web site (http:// go.microsoft.com/fwlink/?linkid=88097). Troubleshooting If you are having problems setting up Windows Home Server, make sure you do the following: Plug in and power on your home server. Connect your home server with a wired network connection to your broadband router or to a switch that is connected to your broadband router. If you are having problems setting up the Windows Home Server Connector software on your home computers, make sure you check the following: Connect your home computer to your home network (using either a wired or a wireless connection), and make sure the home computer is on the same logical network as Windows Home Server. Make sure firewall software on your home computer is not blocking access to Windows Home Server. If your computer has been joined to a corporate network (such as a corporate laptop), check with the corporate network administrator about the IPsec policy. This may block access from the corporate computer to Windows Home Server. For the latest information about Windows Home Server, see Release Documentation for Windows Home Server at the Microsoft Web site (http:// go.microsoft.com/fwlink/?linkid=84725). 10
Securing your Harmony Home Server The data on your unit is safely duplicated once you have connected at least one additional USB HDD, and enabled folder duplication - this is a very safe environment for your precious files to be stored in. However, you have made changes to your unit, by adding new users, folders, USB HDDs etc. These settings, and the operating system can now be protected. Protecting your system From a connected PC, use the server console to shut down the server. De-power or unplug your connected USB HDDs. Insert the red Tranquil Imager USB key into any USB port (USB1-4) Power up the unit and wait, You may see some HDD activity, and USB activity After approx 6 8 minutes the system will automatically shut down. Remove the red USB key, and re-connect, re-power your USB HDDs. Re-power the unit The protection process is completed. If you make any subsequent substantial changes to you system setup then you can repeat the above process again. The above process does not change or backup your data. In the event that you wish to go back to a previous saved state (perhaps after installation on a undesirable plug in) or if your system fails to boot correctly (fatal system failure). You can do this very simply. Restoring your system With the unit in the power OFF state De-power or unplug your connected USB HDDs. Insert the green Tranquil Recovery USB key into any USB port (USB1-4) Power up the unit and wait, You may see some HDD activity, and USB activity After approx 6 8 minutes the system will automatically shut down. Remove the green USB key, and re-connect, re-power your USB HDDs. Re-power the unit The recovery process is completed. The system will now be is a state the same as when you last protected it The data on your system is never affected by either the protection or recovery process. 11
Specification Dimensions (outer) Weight 224 (d) x 232 (h) x 57 (w) (not incl connectors) 2.9Kg Surface area (alloy) 574,000 mm 2 Materials in use Aluminium 92% Steel 7% (rear and inner plates) Plastic 1% (front covers) CPU / North Bridge cooling Internal storage Mounting PSU system Unique Features TranCool system 500GB SATA (approx 350GB usable) Optional 4x USB HDD ports Desk vertical Must use in open space (Max Ambient Temp = 37 C) 12V in (desk use) PSU (>80% efficient) Efficient CPU Near Silent (fan less) Precision engineering Robust design Very small footprint on desk (127cm2) Desk lock facility Ultra low power Extremely reliable Connectivity Ethernet (10/100/1000) USB 2.0 (x4)c input 12V DC output to support up to 4x 12V DC HDDs Power Consumption Carbon footprint MTBF Base unit (Idle) 24W Offset by Tranquil PC Ltd for 5 years in use >50,000 hours Contact For support information please call ( UK ) 0845 555 77 88 ( tech support option ) during normal office hours, or send a descriptive email to HSA.Support@tranquilpc.co.uk. Or visit www.tranquilpc.co.uk 12