DVI ELR Extender over one CAT5 EXT-DVI-1CAT5-ELR User Manual
Important Safety Instructions 1 Read these instructions 2 Keep these instructions 3 Heed all warnings 4 Follow all instructions 5 Do not use this product near water 6 Clean only with a dry cloth 7 Do not block any ventilation openings Install in accordance with the manufacturer s instructions 8 Do not install or place this product near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat 9 Do not defeat the safety purpose of the polarized or grounding-type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade or the third prong are provided for your safety If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet 10 Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus 11 Only use attachments/accessories specified by the manufacturer 12 To reduce the risk of electric shock and/or damage to this product, never handle or touch this unit or power cord if your hands are wet or damp Do not expose this product to rain or moisture 13 Unplug this apparatus during lightning storms or when unused for long periods of time 14 Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped 15 Batteries that may be included with this product and/or accessories should never be exposed to open flame or excessive heat Always dispose of used batteries according to the instructions
Warranty Information Gefen warrants the equipment it manufactures to be free from defects in material and workmanship If equipment fails because of such defects and Gefen is notified within two (2) years from the date of shipment, Gefen will, at its option, repair or replace the equipment, provided that the equipment has not been subjected to mechanical, electrical, or other abuse or modifications Equipment that fails under conditions other than those covered will be repaired at the current price of parts and labor in effect at the time of repair Such repairs are warranted for ninety (90) days from the day of reshipment to the Buyer This warranty is in lieu of all other warranties expressed or implied, including without limitation, any implied warranty or merchantability or fitness for any particular purpose, all of which are expressly disclaimed 1 Proof of sale may be required in order to claim warranty 2 Customers outside the US are responsible for shipping charges to and from Gefen 3 Copper cables are limited to a 30 day warranty and cables must be in their original condition The information in this manual has been carefully checked and is believed to be accurate However, Gefen assumes no responsibility for any inaccuracies that may be contained in this manual In no event will Gefen be liable for direct, indirect, special, incidental, or consequential damages resulting from any defect or omission in this manual, even if advised of the possibility of such damages The technical information contained herein regarding the features and specifications is subject to change without notice
Operating Notes Shielded Twisted-Pair (STP) CAT-5e or CAT-6 cabling is recommended However, Un-shielded Twisted-Pair (UTP) CAT-5e or CAT-6 cabling is acceptable Shielded cable is preferred as it provides immunity to Electromagnetic Interference (EMI), cell phones, and A/C motors
Features and Packing List Features Extends DVI up to 495 feet (150 meters) over one CAT-5e cable Supports resolutions up to 1080p Full HD and 1920 x 1200 (WUXGA) EDID management for rapid integration of source and display Enable/Disable switches for HPD pass-through Power-Save (Green Mode) selector switch 150m/100m range selector switch configures the extender for maximum range (150 meters) or maximum bandwidth Locking power supplies Surface-mountable 1080P HDCP 22 60Hz, 4:2:0 4K CINEMA DCI, 4096 x 2160 Packing List The DVI ELR Extender over one CAT5 ships with the items listed below If any of these items are not present in your box when you first open it, immediately contact your dealer or Gefen 1 x DVI ELR Extender over one CAT5 (Sender unit) 1 x DVI ELR Extender over one CAT5 (Receiver unit) 1 x 6 ft dual link DVI cable (M-M) 2 x 5V DC power supplies 1 x Quick-Start Guide
DVI ELR Extender over one CAT5 Getting Started
Introduction Getting Started 1 Sender Unit EXT-DVI-1CAT5-ELRS Gefen Link DVI ELR Extender over one CAT5 S 2 3 4 5 5V DC Link DVI In Power
Introduction Getting Started ID Name Description 1 Link Connect a CAT-5 cable from this jack to the Link jack on the Receiver unit 2 5V DC Connect the included 5V DC power supply to this power receptacle 3 Link (LED) This green LED indicates the current state of the product See LED Status (page 10) for more information on LED status messages 4 DVI In Connect the DVI source to this port using the included DVI cable 5 Power This LED indicator will glow bright blue when the included power supply is connected between the 5V DC power receptacle and an available electrical outlet
Introduction Getting Started EXT-DVI-1CAT5-ELRR Gefen Receiver Unit 1 Link DVI ELR Extender over one CAT5 R 2 3 4 5 5V DC Link DVI Out Power
Introduction Getting Started ID Name Description 1 Link Connect a CAT-5 cable from this jack to the Link jack on the Sender unit 2 5V DC Connect the included 5V DC power supply to this power receptacle 3 Link (LED) This green LED indicates the current state of the product See LED Status (page 10) for more information on LED status messages 4 DVI Out Connect the DVI source to the display using a DVI cable 5 Power This LED indicator will glow bright blue when the included power supply is connected between the 5V DC power receptacle and an available electrical outlet
Installation Getting Started Connection Instructions 1 Use the included DVI cable to connect the DVI source to the DVI In port on the Sender unit 2 Connect the Receiver unit to the DVI display using another DVI cable 3 Connect a CAT-5 (CAT-5e or better is recommended) cable, up to 495 feet (150 meters) from the Link jack on the Sender unit to the Link jack on the Receiver unit 4 Connect the included 5V DC locking power supplies to the Sender and Receiver unit Do not overtighten the locking power connectors 5 Connect the AC power cord from the power supply to an available electrical outlet Sample Wiring Diagram CAT5 CABLE DVI CABLE DVI Source Receiver Sender DVI Display EXT-DVI-1CAT5-ELR
DVI ELR Extender over one CAT5 Basic Operation page 9
LED Status Basic Operation The Power and Link LED indicators on the Sender and Receiver unit provide basic information on the current status of the DVI ELR Extender over one CAT5 The information, in the table below, applies to both the Sender and Receiver unit LED Status Description Power Solid blue Power connected to Sender / Receiver unit Off No power supplied to the Sender / Receiver unit Make sure each power supply is connected to the Sender and Receiver unit Make sure that the outlet is live Link Solid green Link integrity between the Sender and Receiver unit is good Source is connected to the Sender unit Display (or other sink device) is connected to the Receiver unit Flashing green No source is connected to the Sender unit Display (or other sink device) is not connected to the Receiver unit Off Link integrity is compromised Check the cable between the Link port on the Sender and Receiver unit
DIP Switch Configuration Basic Operation There is a bank of four DIP switches on the bottom of the Sender and Receiver unit Remove the piece of colored tape to reveal the DIP switch bank These DIP switches provide control over EDID management, HPD pass-through, power modes, and range selection Bottom of Sender / Receiver unit Default Settings Description Sender unit Receiver unit Default settings for Sender and Receiver unit External (downstream) EDID HPD is high Green mode is enabled Long-Reach mode is disabled
DIP Switch Configuration Basic Operation Each of the following sections describe the DIP switch settings that control each feature DIP switches that are not related to a specific feature have been grayed-out Note that DIP switch settings can be used independently or in conjunction with other features, as desired EDID Management When switching between different EDID modes, the Sender unit must be power-cycled in order for the changes to take effect Description Sender unit Receiver unit Copies the downstream EDID locally and modifies it to limit TMDS bandwidth to 225 Mhz support Disables xvycc Modifies manufacturer name to GFN Downstream EDID is used Both DDC and HPD (Hot-Plug Detect) are passed through, allowing the full audio/video capabilities of the display to be used This is the default setting Hot-Plug Detect (HPD) When switching between different HPD modes, the Sender unit must be power-cycled in order for the changes to take effect DIP switch 1 must be in the OFF position Description Sender unit Receiver unit Forces HPD high This is the default setting HPD is passed through from the sink to the source
DIP Switch Configuration Basic Operation Power Mode Description Sender unit Receiver unit Power-Save (Green) mode The Receiver unit is powered only when a video signal is present on the DVI (or HDMI) cable Sleep Mode consumes less than 1 Watt of power This is the default setting Normal mode In this mode, the Receiver unit is always powered Long-Reach Mode When set to Long-Reach mode, both audio and video can be extended up to 495 feet (150 meters) However, the color depth is limited to 8-bit Description Sender unit Receiver unit Long-Reach mode Audio and video can be extended up to 495 feet (150 meters) Video color depth is limited to 8-bit Normal mode Audio and video can be extended up to 330 feet (100 meters) Color depth up to 12-bit is supported This is the default setting
DVI ELR Extender over one CAT5 Appendix
Specifications Appendix Supported Formats Resolutions (max) 1920 x 1200 (WUXGA) 1080p Full HD Connectors, Indicators, and Controls DVI In (Sender) 1 x DVI-I, 29-pin, female (digital only) DVI Out (Receiver) 1 x DVI-I, 29-pin, female (digital only) IP control (Sender / Receiver) 1 x RJ-45 Power (Sender / Receiver) 1 x 5V DC, locking Power Indicator (Sender / Receiver) 1 x LED, blue Link Indicator (Sender / Receiver) 1 x LED, green DIP Switches (Sender / Receiver) 4 x SPDT Operational Maximum Pixel Clock 165 MHz Power Consumption (Sender / Receiver) 10W per unit (max) Operating Temperature +32 to +140 F (0 to +45 C) Operating Humidity 0 to +90% RH, non-condensing Physical Dimensions (W x H x D) (Sender / Receiver) 43 x 1 x 34 (110mm x 26mm x 86mm) Unit Weight (each) 036 lbs (016 kg)