Quantum 369375f 1 11.05.15 QuantumR Hub (QP2) The Quantum light management hub provides a centralized connection point for Lutron EcoSystem digital ballast modules, Lutron power panels, and QS devices and shades. Features Designed to control, manage, and monitor EcoSystem lighting, Lutron power panels, and QS devices and shade systems in a building or whole campus. Supports both astronomic and time-of-day events to automatically control the lights and shades in the system. Simple reconfiguration of a space without rewiring for EcoSystem devices. Individually control, monitor, and adjust any light or shade in a space. QS control links and EcoSystem loops are topology-free. For EcoSystem loads, the light management hub accepts one normally closed (NC) emergency input per Quantum bus supply. EcoSystem bus may be wired NEC Class 1 or IEC PELV / NEC Class 2. QP2 Hub Capabilities Each QuantumR Hub (QP2) supports up to 8 EcoSystem loops, (4 Quantum bus supplies). Each loop can have a combination of 64 EcoSystem ballasts and ballast modules, plus a maximum of 16 daylight sensors, 32 occupancy sensors, and 64 infrared (IR) devices. Supports up to 2 Quantum processors with 2 links each that can be individually configured to communicate with: - Quantum bus supply (limited to one link per QP2 hub) - Lutron power panels - Lutron QS devices
Quantum Specifications 369375f 2 11.05.15 Regulatory Approvals culus Listed (Reference: UL File E42071) CSA Certified California Energy Commission Listed Seismic Certified (Test Method AC156. Reference OSHPD Preapproval OSP-0215-10) NOM certified models available Power Input voltage: 120 V~, normal/emergency feed 50/60 Hz 15 A Output: EcoSystem - 18 V- 250 ma per loop Processor - 24 V- 1 A per link Physical Design Enclosure: NEMA Type 1, IP-20 protection 16 U.S. gauge steel Weight: 45 Ib (20.4 kg) (with packaging) Seismic Certification Limits: S DS = 2.5 g, z/h = 1.0, I P = 1.5. Contact Lutron for details. Mounting Surface-mount only Environment For indoor use only 32 ºF to 104 ºF (0 ºC to 40 ºC) Relative humidity less than 90% non-condensing
Quantum How to Build a Model Number Example QP2-2P8CSE - 120 Hub Type Number of Processors Number of Loops Accessory Device Voltage Available Model Numbers Contact Lutron for options not listed below. QP2-0P0CSE-120 (for rough-in use) QP2-1P0CSE-120 QP2-1P2CSE-120 QP2-1P4CSE-120 QP2-1P6CSE-120 QP2-1P8CSE-120 QP2-2P0CSE-120 QP2-2P2CSE-120 QP2-2P4CSE-120 QP2-2P6CSE-120 QP2-2P8CSE-120 369375f 3 11.05.15 Hub Type QP2 = Quantum Hub Number of Processors 0P = 0 Quantum processors 1P = 1 Quantum processor 2P = 2 Quantum processors Number of Loops 0C = 0 EcoSystem loops 2C = 2 EcoSystem loops 4C = 4 EcoSystem loops 6C = 6 EcoSystem loops 8C = 8 EcoSystem loops Accessory Device SE = 5-port Unmanaged Ethernet Switch Voltage 120 = 120 V~
R R Quantum Dimensions Shown as in (mm) 369375f 4 11.05.15 15.75 (400) Top View 2.5 (63.5) 15.75 (400) 12.75 (324) 5.81 (148) 0.15 (4) 31.5 (800) 26.5 (673) 31.5 (800) Left Side View Front View Right Side View Bottom View
Quantum 369375f 5 11.05.15 Mounting and Conduit Entry Surface-mount indoors. Hub generates heat. Mount only where temperature will be 32 F to 104 F (0 C to 40 C). This equipment is air-cooled. Do not block vents or warranty will be void. A minimum of 12 in (305 mm) of unobstructed space is required in front of and below the hub for ventilation. Water damages equipment. Mount in a location where the hub and processors will not get wet. Mount within 7 of true vertical. Digital ballast wiring can be Class 1 or IEC PELV / NEC Class 2; always keep Class 1 and Class 2 wiring separate, and follow all applicable local and national electric codes. Reinforce wall structure for weight and local codes. Hub Maximum BTUs/Hour Weight (without packaging) All models 220 45 Ib (20.4 kg) Mount hubs so line (mains) voltage wiring is at least 6 ft (1.8 m) from sound or electric equipment and wiring. Dedicated feed Line voltage only Digital ballast loops NEC Class 1 or IEC PELV / NEC Class 2 only Ceiling IEC PELV / NEC Class 2 wiring only for control links and Ethernet connection Alternate ballast wiring entry Alternate ballast wiring entry Alternate IEC PELV / NEC Class 2 entry Alternate IEC PELV / NEC Class 2 entry Wall Alternate ballast wiring entry Alternate IEC PELV / NEC Class 2 entry Front View Side View
Quantum Hub Overview Line voltage input, normal/emergency feed 369375f 6 11.05.15 Receptacle (for Lutron use only) Hub power switch IEC PELV / NEC Class 2 power supply board IEC PELV / NEC Class 2 wire trough Ballast wire trough Quantum bus supplies (4 modules, 2 loops per module maximum) Factory configured Quantum bus supply link Configurable links (power panel, Lutron QS, or Quantum bus supply) Processor LEDs 5-port unmanaged Ethernet switch Quantum processors (2 maximum)
Quantum Line Voltage Wiring 369375f 7 11.05.15 GND N 120 V~ N/E Ground/Earth (green) Neutral (white) Line / Hot (black) Notes Line voltage must enter hub from top right of hub Run a dedicated 120 V~ normal/emergency feed Lutron recommends that no more than four Hubs are powered by a single derated 20 A circuit Run wiring so line (mains) Class 1 voltage is separate from IEC PELV / NEC Class 2 wiring
Quantum Quantum Inter-Processor Link Wiring Example of Inter-Processor Wiring: Riser Diagram 369375f 8 11.05.15 Quantum Hub Floor Quantum Hub Floor Ethernet switch Notes The inter-processor wiring is considered IEC PELV / NEC Class 2; do not run in the same conduit as line (mains) voltage wiring. Wiring distance for any single link segment is 330 ft (100 m) max; use additional network equipment for longer distances. Processors cannot be more than 6 wire segments from the server. Processors communicate over the inter-processor link using multicast UDP; a dedicated network is recommended for the lighting control system. Processors within the hub are pre-wired to the Ethernet switch. Quantum Hub Floor Quantum Hub Unmanaged Ethernet switch Quantum Hub To additional Quantum Hubs Quantum server
Quantum Dedicated Quantum Bus Supply Link 369375f 9 11.05.15 Notes EcoSystem bus may be wired in accordance with NEC Class 1 or IEC PELV / NEC Class 2 practices Sensors and Quantum bus supply contact closures must be wired IEC PELV / NEC Class 2 Dedicated Quantum bus supply link; prewired by Lutron to Quantum Bus Supply located in hub Note: If Quantum bus supply link is not required, this can be used as a configurable link. Power is not available from the Quantum hub on this link. An external power supply is required to power devices on this link. QP2-2P8CSE-120 shown EcoSystem Bus Diagram To additional ballasts and modules (up to 64 total) EcoSystem ballast 1 2 3 4 5 6 7 8 EcoSystem interface module 3-wire Hi-lume ballast or driver* EcoSystem ballast EcoSystem ballast IR receiver ing remote Quantum bus supply (in hub) Occupant sensor (32 maximum per EcoSystem loop) Pico Wired Control Daylight sensor (16 maximum per EcoSystem loop) * Does not count as one of the ballasts or modules on the EcoSystem bus
Quantum Quantum Bus Supply OPT Switches and LEDs 369375f 10 11.05.15 H/L H/L N N ON1 2 3 4 5 6 7 8 6 7 8 OFF ON position position OPT Switches OPT switches are used to configure the Bus Supply. The tables below describe the options. To place an OPT switch in the OFF position, slide the switch to the left; away from the switch s number. Default is ON (next to the switch s number). E2 E2 E1 E1 E2 E2 E1 E1 OPT Switch Functions Bus Supply Numbers: 1 2 3 4 Address Numbers: 1, 2 3, 4 5, 6 7, 8 1 Addressing 2 Set address for bus supply s loops 3 (2 loops per bus supply) 4 Green Loop (right side) 5 Manual override levels 6 Blue Loop (left side) Manual Override levels 7 ON 1 2 3 Bus Supply 1 Addresses 1, 2 4 5 s stay at current level 6 7 s stay at current level ON 1 2 3 Bus Supply 2 Addresses 3, 4 4 5 s go to high level 6 7 s go to high level ON 1 2 3 Bus Supply 3 Addresses 5, 6 4 5 s go to low level 6 7 s go to low level ON 1 2 3 Bus Supply 4 Addresses 7, 8 4 5 s go to Off 6 7 s go to Off 8 Manual Override 8 Manual override levels will be used 8 s will go to the level specified by the system H/L H/L N N ERR EMG BUS ERR EMG BUS ON 1 2 3 4 ERR EMG BUS ERR EMG BUS STAT V PWR Status LEDs LEDs on the Quantum Bus Supply indicate network status. The specific LEDs, color and flashing method is detailed below. STAT V PWR E2 E2 E1 E1 E2 E2 E1 E1 (Blue) (Green) LED Normal Operation Problem Indicator Probable Cause V~ PWR On Off No Mains power STAT Steady flash Off No Mains power or unit fault On Unit fault BUS Intermittent flash On Unit fault or Off ERR/EMG Off On Emergency contact closure is active Steady flash Miswire detected on corresponding bus
1 2 3 4 5 6 7 8 Quantum Quantum Bus Supply Wiring Line voltage in (prewired by Lutron) 369375f 11 11.05.15 Processor link (prewired by Lutron; not visible in this view) DL7 DL8 E1 E2 E1 E2 EM C Emergency input (normally closed) E2 E1 E2 EcoSystem devices E1 Wire Gauge Max. Bus Length 12 AWG (4.0 mm 2 ) 2200 ft (670 m) 14 AWG (2.5 mm 2 ) 1400 ft (427 m) 16 AWG (1.5 mm 2 ) 900 ft (274 m) 18 AWG (1.0 mm 2 ) 570 ft (175 m) Notes E1 and E2 wires are not polarity sensitive. Line / Hot, neutral, and ground wires are also connected to each lighting fixture; some may have an emergency feed. Wire-free topology. To additional EcoSystem devices If 15 V- +/- 1 V- is not present between E1 and E2, check the Quantum bus supply wiring. A short between E1 and E2 will cause the bus supply to stop providing voltage on the bus and will cause the ERR indicator to flash. Removing the short between E1 and E2 will allow the bus supply to operate properly. To wire the Quantum bus supply for IEC PELV / NEC Class 2, the Quantum bus supply wires must be separated from the mains wiring. Otherwise, the IEC PELV wiring must be classified as NEC Class 1.
Quantum Configurable Link Wiring: Power Panel Link 369375f 12 11.05.15 Power panel Power panel Power panel DRAIN _ V+ COM 5 4 3 2 1 1 COM 2 N/C 3 4 D DRAIN 5 Sense line 1 COM 2 N/C 3 4 D DRAIN 5 Sense line 1 COM 2 N/C 3 4 D DRAIN 5 Sense line 4 3 3 4 Link terminator (LT-1) Quantum Bus Supply link Configurable links Control wiring (1) 12 AWG (4.0 mm 2 ) 1: Common Data link (1) shielded, twisted pair 22 AWG (0.5 mm 2 ) 3: 4: _ D: Drain wire in shield (keep away from ground and all electronics) IEC PELV / NEC Class 2 Terminal Wiring (2) 12 AWG (4.0 mm 2 ) Drain Data link: twisted, shielded pair 22 AWG (0.5 mm 2 ) 3: 4: _ Sense: 18 AWG (1.0 mm²) Link terminator (LT-1) Emergency/essential sense line (1) 18 AWG (1.0 mm²) 5: Sense line Sense line is used when there is a panel being supplied by an emergency/essential feed 1 2 3 4 D 5 C D Data A OK Power OK Data B OK Notes Power panel link must be daisy-chained (no T-taps). Maximum of 32 circuit selectors per link. It is not necessary to have the Quantum hub at the end of the link. The sense wire (terminal 5) is used whenever there is a panel being supplied by an emergency/essential feed; see power panel instructions for details. Each low-voltage IEC PELV / NEC Class 2 terminal can accept only two 18 AWG (1.0 mm 2 ) wires. Two 12 AWG (4.0 mm 2 ) conductors will not fit. Connect as shown using appropriate wire connectors. Common 24VFW Drain Sense Link Link A B 1 2 3 4 D 5 C D SELECT CIRCUIT Comm Drain Total length of the power panel link may be no more than 2000 ft (600 m). Power panel link can be extended up to three times using a -RPTR interface to reach a total length of 8000 ft (2400 m). GRX-CBL-46L IEC PELV / NEC Class 2 wiring cable is available from Lutron and contains two 12 AWG (4.0 mm 2 ) conductors for control power, one twisted, shielded pair of 22 AWG (0.5 mm 2 ) for data link, and one 18 AWG (1.0 mm 2 ) conductor for emergency (essential) sense line.
Quantum 369375f 13 11.05.15 Configurable Link Wiring: QS Link (5) Drain (Shield) (4) _ (3) (2) 24 V- (1) COM QS Link Wiring: 22 AWG to 12 AWG (0.5 mm( to 4.0 mm() Available Power Draw Units (PDUs) per link Maximum Link Length Wire Gauge Available from Lutron in one cable 33 500 ft (152.4 m) Power (terminals 1 and 2) 1 pair 18 AWG (1.0 mm 2 ) Data (terminals 3 and 4)1 pair 22 AWG (0.5 mm 2 ) twisted and shielded Power (terminals 1 and 2) 1 pair 12 AWG (4.0 mm 2 ) Data (terminals 3 and 4) 1 pair 22 AWG (0.5 mm 2 ) twisted and shielded GRX-CBL-346S GRX-PCBL-346S 33 2000 ft (609.6 m) GRX-CBL-46L GRX-PCBL-46L Notes System communication uses IEC PELV / NEC Class 2 low-voltage wiring. Follow all local and national electrical codes when installing IEC PELV / NEC Class 2 wiring with line voltage/mains wiring. Each terminal accepts up to two 18 AWG (1.0 mm() wires or one 12 AWG to 22 AWG (4.0 mm( to 0.5 mm() wire. Total length of QS link must not exceed 2000 ft (600 m). Contact Lutron Technical Support for applications needing to extend QS link wiring. A Quantum QS link can have up to 512 switch legs (outputs) and 99 devices. The Quantum Hub provides 33 power draw units (PDUs) on the QS Link. For more information, see Power Draw Units on the QS Link (Lutron P/N 369405), at www.lutron.com/qs. Wiring can be T-tapped or daisy-chained. Wire sizes: - Two 12 AWG (4.0 mm 2 ) conductors for control power. - One twisted, shielded pair of 22 AWG (0.5 mm 2 ) for data link. - Cable is available from Lutron: GRX-CBL-46L.
QP3-1PL-100-240 Input: 1 A 120-240 V~ 50/60 Hz Output: 2 A 24 V --- (IEC PELV/NECR Class 2) Entree: 1 A 120-240 V~ 50/60 Hz Sortie: 2 A 24 V --- (IEC PELV/NECR Class 2) Entrada: 1 A 120-240 V~ 50/60 Hz Salida: 2 A 24 V --- (IEC PELV/NECR Class 2) QP3-1PL-100-240 Input: 1 A 120-240 V~ 50/60 Hz Output: 2 A 24 V --- (IEC PELV/NECR Class 2) Entree: 1 A 120-240 V~ 50/60 Hz Sortie: 2 A 24 V --- (IEC PELV/NECR Class 2) Entrada: 1 A 120-240 V~ 50/60 Hz Salida: 2 A 24 V --- (IEC PELV/NECR Class 2) Type 1 Enclosure Type 1 Enclosure Quantum 369375f 14 11.05.15 Configurable Link Wiring: QS Link (continued) Only terminals 1, 3, and 4 connected between devices that supply PDUs COM Terminal 2 NEVER connected between devices that supply PDUs All 4 terminals connected to QS link devices that consume PDUs COM +24 V Devices that supply PDUs Devices that consume PDUs QS link; all 4 terminals QuantumR Hub (QP3) QS Device Interface Wired QS Keypad QSM Interprocessor wiring Unmanaged Ethernet switch provided by others (contact Lutron for Ethernet switch options provided by Lutron) Terminal 2 (+24 V) NEVER connected* QS link; no terminal 2 QS link; all 4 terminals QuantumR Hub (QP3) QS link; all 4 terminals Wired QS Keypad QSM QSM Step-PS QS Link power supply ** Wired QS Keypad QS Device Interface Wired QS Keypad + QS Link Wiring Rules * Terminal 2 (+24 V) should NEVER be connected between devices that supply PDUs. ** For QS Link power supply wiring connection details, refer to the installation instructions for the specific power supply model being used.