TIBO AUDIO PA500 Owner s manual Please read this manual carefully before using this product and then retain for future reference. 1
CONTENTS CONTENTS 3 WHAT S IN THE BOX 4 SAFETY Safety precautions 5 Important safety instructions 6 CONNECTIONS 8 TECHNICAL DATA 9 OTHER TIBO AUDIO PRODUCTS 10 TROUBLE SHOOTING 11 3
WHAT S IN THE BOX 1 x 1 x 1 x TIBO AUDIO PA500 Owner s manual 1 x 1 x 5 m www.tiboaudio.com 4
SAFETY Safety precautions A triangle with a lighting symbol draws the user s attention to dangerous voltage without insulation in the cabinet which may be high enough to entail a risk of an electric shock. A triangle with an exclamation mark draws the user s attention to important instructions for use and maintenance in the accompanying manual, which should be studied and adhered to. The symbol for a CLASS II (double insulation) product. Warning: Caution: To minimise the risk of fire or electric shock, do not expose the unit to rain or moisture. Do not open the cabinet as it contains dangerous voltages. Only qualified technicians are allowed to carry out repair and service of this system. If the plug of the power cord needs to be replaced. It is important that the replacement is identical to the plug that needs to be replaced, or that the new plug has been recommended by the manufacturer. To avoid electric shock, it is important to insert the plug correctly into the wall outlet. 5
Important safety instructions SAFETY Warning: It is important that you read and observe both the instructions in this manual and the instruction on the unit. Keep this manual for safe future reference. This unit was designed and manufactured with a view to providing maximum safety for the user. Incorrect use of the unit may cause an electric shock or fire. The protection devices built into this unit will protect the user if the procedures below are observed in connection with installation, use and repair. This unit is fully electronic and contains no parts that can be repaired by the user. Do not remove the covers. Risk of dangerous voltage. Only qualified technicians are allowed to repair the unit. Read the manual After unpacking the unit, please read the manual carefully and observe all the instructions given. Power supply Only the power supply indicated on the rating plate must be used for this unit. If you are not sure which power supply you have, please contact your local shop. Earthing or polarisation If the plug cannot be inserted properly into the socket, or if the plug does not fit, the unit must not be used in your country. Ventilation The cabinet is provided with slots and openings to ensure ventilation and reliable operation and to protect the unit against overheating. Do not block or cover these openings. The openings must never be blocked, for instance by placing the unit on a bed, a sofa, a carpet or similar surface. Water and moisture The unit must not be placed close to water, such as bathtub, wash basin, kitchen sink or laundry tub, in a damp cellar or close to a swimming pool, etc. Cleaning Unplug the unit before cleaning. Do not use liquid detergents and aerosol cleaning agents. Use a dry cloth. Power cords Wiring must be organised to prevent people from stepping on the cables and to avoid pinching by objects placed on or beside them. Take special care around sockets and plug boxes and where the power cords leave the unit. Lightning Unplug the unit for additional protection during storms or when the unit is not used for prolonged periods. This will prevent damage to the unit from lightning and power surges. Heat Do not place the unit near sources of heat such as radiators, ovens or other units that produce heat. www.tiboaudio.com 6
Important safety instructions SAFETY Penetration of objects and liquid Never push any foreign objects through the openings into the unit, as they may touch dangerous voltage points or short-circuit parts and cause fire or an electric shock. Do not spill liquid onto the unit. Accessories Do not place the unit on unstable surfaces such as a trolley, stand, tripod, shelf or table. The unit may fall and injure children or adults or be seriously damaged. Use only trolley, stand, tripod, shelf or table that is very stable or provided with the unit. The unit must be installed in accordance with the manufacturer s instructions and by means of installation equipment recommended by the manufacturer. If the unit is placed on a trolley, the trolley must be moved very carefully. Sudden stops, unnecessary force and uneven surfaces may cause the trolley to turn over. Loads Do not place heavy loads on the unit and do not step on it. The load may fall and cause serious injury to persons or damage to the unit. Damage Unplug the unit and contact qualified technicians in the following cases: A) If the power cord or the plug is damaged. B) If liquid has been spilled on the unit or objects have fallen into the unit. C) If the unit has been exposed to rain or water. D) If the unit does not work properly after adhering to the instructions in the operation manual. Only the settings described in the operation manual must be made as incorrect setting may result in damage and often will make it difficult for a qualified technician to make the unit work properly again. E) If the unit has been dropped or damaged in any other way. F) When the operation of the unit changes drastically, the unit requires service. Service Do not attempt to carry out any service work by yourself. By opening or removing the cover, you will be exposed to dangerous voltage or other hazards. Any service work should be carried out by qualified technicians. Recycling If at any time in the future you need to dispose of this product please note that waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice. Approval This product complies with European Low Voltage and Electromagnetic Compatibility Directives when used and installed according to this instruction manual. 7
P A 5 00 CONNECTIONS 15 16 2 3 5 6 8 9 TIBO AUDI 14 1 4 7 10 11 12 13 10. Treble control Use this control to adjust the treble level. 11. Bass control Use it to adjust the bass level. 12. On/Off power switch Press to power on/off the speaker box. 13. AC power socket and fuse carrier Use it to connect the AC power cord. Replace the fuse only with the correct type and rating as specified on the rear panel. 14. USB/SD volume control Use to set USB/SD volume level. 15. USB port Connect a compatible USB memory device. 16. SD memory card slot Connect a compatible SD card. 1. Microphone volume control Use this control to set the volume level of the microphone (6.3 mm or balanced). 2. XLR balanced microphone input XLR connection for a balanced microphone 3. Microphone input 6.3 mm jack connection for a microphone 4. Line-in volume control Use this control to set the volume level of the Line-In signal. 5. RCA Line-In RCA connection for an external audio device (CD, radio, DVD, etc.) 6. XLR line-in XLR connection for an external audio device (CD, radio, DVD, etc.) 7. Volume control Use this control to set the general volume level. 8. 6.3 mm line-out 6.3 mm jack connection for an external audio device. 9. XLR line-out XLR connection for an external audio device. 2 3 1. LCD Screen 2. Play/Pause Press to start playing music. Press one more time to pause current track, to return normal mode, press again. 3. Stop Press to stop current track. 4. Play mode Select a playing mode. R1: Repeat one, RA: Repeat All, RD: Random. 5. Backward Press to skip to previous track. Press and hold to go back a track during playback. 6. Forward Press to skip to next track. Press and hold to go forward a track during playback. 1 6 5 4 www.tiboaudio.com 8
TECHNICAL DATA Type: Tweeter: Woofer: Frequency: Crossover: Output power: Inputs: Outputs: Dimensions: Weight: 2 way full range powered speaker 34 mm titanium 305 mm 50-18.000 Hz 3.5 khz 120 W RMS XLR for microphone 6.3 mm jack for microphone XLR RCA USB, CD card XLR 6.3 mm jack 590(H) x 35(W) x 310(D) mm 18 kg We reserve the right to change the technical data and the design of the product without notice as a result of further development. 9
DJ PRO 2000 specification OTHER TIBO AUDIO PRODUCTS Mixer: Large LCD display with blue back light 2 x CD drive 2 x USB slot Mp3 playback ipod docking station 40 sec. Anti-Shock system Loop and re-loop function Jog mode: pitch, bend, scratch, search 2 x XLR outputs 2 channel mixer, fader Inputs: microphone (jack/xlr), headphones) Microphone: Superb quality dynamic microphone Delivers a crisps detailed performance Frequency response: 50-15,000 Hz 4 metre microphone cable included Headphones: Exceptional sound output Frequency response: 15-22,000 Hz Very comfortable to wear Loudspeakers: 2 way bass reflex active loudspeakers 25 mm DXT soft dome tweeter 165 mm polypropylene woofer High power 2 channel stereo amplifier built-in Connection for active subwoofer Cloth covers included Need Help? You can contact our technical support Monday - Friday 8 AM to 4 PM 0845 2711 906 info@tibo-electronics.com www.tiboaudio.com 10
TROUBLE SHOOTING Symptom Likely Cause What to do No sound Unit is not connected to active AC power. Verify that unit is connected and the circuit is on. No sound, the unit is connected to working AC power but won t come on. Power not switched on. Unit power cable is faulty or improperly connected. Blown fuse. Switch on power and verify that power LED is on. Re-seat the power cable at both ends. Substitute a known-good power cable. Check fuse and replace with same type spare fuse in holder. Unit is operating but there is no sound. Faulty cables and connections Disconnect and re-seat signal cables. Replace suspected cable with a knowngood cable. Check that your USB or SD device is properly connected and has music content. Signal sounds distorted and very loud. Signal sound distorted even at moderate volumes. Lots of hiss in the sound, the mixer controls are at very low settings. Excessive input signal, trying to exceed the capabilities of the speakers. Excessive BASS or TREBLE boost. Mixer or the source is overdriven. Improper gain structure Reduce the output level of the source. Turn down the level controls on the speaker. Reduce BASS or TREBLE control. Review the owner s manual for your mixer or other source and adjust controls as needed. Input sensitivity (gain). Channel faders. Make sure that the MIC/LINE switch is in the LINE (disengaged) position. Reduce the level settings at speaker. Review the owner s manual for your mixer or other source and adjust controls as needed. Input sensitivity (gain). Channel faders. Master faders. Noise or hiss heard at output. Noisy source device. Disconnect the devices that are connected to your unit one at a time. If the noise goes away, the problem is with the source or the connecting cable. Hum or Buzz that increases or decreases when the mixer level controls are moved. Improper A/C ground or faulty equipment connected to mixer input. Faulty cable between source equipment and unit. Disconnect inputs one at a time to isolate the problem. Refer to the owner s manual of the faulty equipment for troubleshooting help. Substitute a known-good cable for the suspected faulty cable. 1
www.tiboaudio.com