Dymec Serial Links SubStation Hardened RS232 Serial Copper to Fiber Link/Repeaters Features Single Channel RS232 or TTL Logic Powered from Station Battery Bus Operates reliably at temperatures of 40 C to 85 C Extended distances of 5km over Multi-mode fiber and 30km over Single-mode fiber. Multiple Mounting choices with built-in mounting brackets and optional mounting shelf Packaged in rugged, industrialquality Galva Neal and powder coated shells 4 Diagnostic LEDs for easier debug of installation Conformal coated PC boards Compatible with all earlier 5843/ 5844 versions of Dymec Link/Repeaters Certified to IEEE 1613 and Class 1 Div 2 Dymec models 5843 and 5844 are hardened fiber optic Link/Repeaters that convert RS232 or TTL level copper to amplitude based fiber output. Supports data rates from dc to 250k bps, DCE or DTE port configuration and a diagnostic/test mode that allows testing of the copper and fiber connections before the connected IED is active in the network. By simply setting a few switches, the Dymec 5843 and 5844 Link/Repeaters can be configured for pointto-point, star, optical bus, or loop networks, and permit quick, easy connection of devices. For example, an extensive multi-drop network where two or more intelligent electrical devices are connected and communicating can be constructed simply by connecting the devices through Link/Repeaters. Dymec 5843 and 5844 Link/Repeaters may optically connect devices of different formats, eliminating the need for format converters. For example, an RS232 IED may be connected to a model 5844 which is optically connected to a model 5846, which, in turn, can communicate electrically to its IED in EIA 485.
Specifications Optical Parameters @ Max Temp Multimode Single-Mode Optical Budget Typical 19.5dB 19dB Output Power Typical -10.5 dbm peak -14.5 dbm peak Receiver Sensitivity Typical -30 dbm peak -33.4 dbm peak (62.5µ/125 Multimode) (9µ/125 Single-mode) Wavelength 850nm 1310nm Connector Type ST Compatible Fiber Type Multimode (50-200µm) Single-Mode (9-13µm) Configuration (Switches) DTE/DCE AC/DC Coupled Link/Repeat Pin 8 Drive Current Pin 6 +5 Vdc (DSR or CTS pull up) Diagnostic Mode Data Rate DC to 250kbps Data Transmission Asynchronous, simplex Or Full Duplex Transmission Distance Up to 5000 meters Up to 30K meters (62.5µ/125 Cable@3dB/km) (9µ/125 Cable@.5dB/km) Bit Error Rate 10-E9 Max. Point to Point Latency 4µS Repeat Latency 400 nsec Max Electrical Parameters Inputs I/O Data Format EIA RS232; CCITT v.24 Data Connector 9 pin D-Type Female Input Impedance >3000Ohms Input voltage +/-30 Volts Max Outputs Output Impedance >300Ohms Driver Output Pin 8 Output +/-5Volts into 3000Ohms 0 to 5V 67 or 207 Ohm Source Impedance Ambient Temperature Operating Temperature -40 to +85 C -40 to +70 C Storage Temperature -40 to 85 C Power Required 5844 4.0 Watts 5.5 Watts 35 ma @ 90-250 V 50 ma @ 90-250 V 250 ma @ 18-60 V 340 ma @ 18-60 V 5943 3.0 Watts 4.1 Watts 250mA @ 12Vdc 340mA @ 12Vdc Power Dissipation BTU/H 5844 10.9 BTU/hr 12.3 BTU/hr 5843 8.2 BTU/hr 10.2 BTU/hr Physical Parameters Weight 5844 17 oz. 5843 9 oz. Dimensions Inches 5844 4.1W x 5.1L X 1.3H 5843 2.0W x 5.1L X 1.3H Indicators Power Transmit Fiber Transmit Electrical Receive Fiber Receive Electrical Ordering Information Model Input Fiber Type Input Power Rating 5843HRT RS-232/TTL Multi-Mode 9-15 Vdc 5844HRT-H RS-232/TTL Multi-Mode 90-250Vdc/90-250Vac 5844HRT-L RS-232/TTL Multi-Mode 24-48 Vdc 5843SHRT RS-232/TTL Single-Mode 9-15 Vdc 5844SHRT-H RS-232/TTL Single-Mode 90-250Vdc/90-250Vac 5844SHRT-L RS-232/TTL Single-Mode 24-48 Vdc ACC-LCS ACC-CBL1 Link Cantilever Mounting Bracket DB9 Male/Tinned Lead 10 Foot Cable/Pigtail Dymec Serial Links--5843/5844 GarrettCom, Inc. 47823 Westinghouse Drive Fremont, CA 94539 PH: (510) 438-9071 FAX: (510) 438-9072 Email: mktg@garrettcom.com Web: www.garrettcom.com
Dymec Serial Links Dymec Serial Links SubStation Hardened EIA 422/485 Serial Copper to Fiber Link/Repeaters Features Signal protection and electrical isolation for data connections and devices Certified to IEEE 1613 and Class 1 Div2 Operates at 40 C to 85 C Extended distances of 5km over Multi-mode fiber and 30km over Single-mode fiber. Diagnostic LEDs for easier debug of installation Built-in mounting brackets and optional mounting shelf Packaged in rugged, industrialquality Galva Neal and powder coated shells Conformal coated PC Boards Powered from Station Battery Bus Compatible with all earlier 5845/ 5846 versions of Dymec Link/Repeaters Dymec model 5845 and 5846 Serial Fiber Links are link/repeaters for EIA 422 and 485 data connections. The 5845/5846 Links provide reliable serial data connectivity over fiber optic facilities in harsh environments where immunity and signal isolation are critical. Optical connectivity provides flexibility, extendeddistance, operational safety, reduced equipment outages due to electrical surges, and improved signal quality and network performance. 5845/5846 Links support signal rates from DC to 2 Mbps and operate either full- or half-duplex over single- or multimode fiber. Links are easily fieldconfigurable for point-to-point, master/slave, loop, bus or star topologies. The 5845/5846 also interoperate with 5843/5844 RS232 Links, the Dymec Network Integration System and Optical Star products to costeffectively create highly scaleable data networks with minimum electrical signal exposure. Dymec Links are substation-hardened to IEEE 1613 specifications. They operate in an extended temperature range and optionally take DC power directly from station battery. Flexible mounting options, diagnostic LEDs and integrated optical and electrical signal test features make turning up Link networks simple.
Specifications Dymec Serial Links--422/485 Optical Parameters @ Max Temp Multimode Single-Mode Optical Budget Typical 19.5dB 19dB Output Power Typical -10.5 dbm peak -14.5 dbm peak Receiver Sensitivity Typical -30 dbm peak -33.5 dbm peak (62.5µ/125 Multimode) (9µ/125 Single-mode) Wavelength 850nm 1310nm Connector Type ST Compatible Fiber Type Multimode (50-200µm) Single-Mode (9-13µm) Configuration (Switches) Half/Full Duplex AC/DC Coupled Link/Repeat Biasing Resistors In/Out Data Inversion Mode Enable Holdover (4 settings) Diagnostic Mode Data Rate DC to 2M bps Data Transmission Asynchronous, simplex Or Full Duplex Transmission Distance Up to 5000 meters Up to 30K meters (62.5µ/125 Cable@3dB/km) (9µ/125 Cable@.5dB/km) Bit Error Rate 10-E9 Max. Point to Point Latency 500 nsec Max Repeat Latency 400 nsec Max Electrical Parameters Inputs I/O Data Format EIA 422/485 Data Connector 9 pin D-Type Female Input Impedance 750Ohms +12 to -7 Volts Max referenced to signal common Input Voltage +/-6 Volts differential Max Outputs Output Impedance >250 Ohms Driver Output 50 ma Ambient Temperature Operating Temperature -40 to +85 C -40 to +70 C Storage Temperature -40 to 85 C Power Required 5846 6.0 Watts 8.0 Watts 45 ma @ 90-250 V 60 ma @ 90-250 V 250 ma @ 18-60 V 340 ma @ 18-60 V 5845 3.0 Watts 4.0 Watts 250mA @ 12Vdc 340mA @ 12Vdc Power Dissipation BTU/H 5846 20 BTU/hr 27 BTU/hr 5845 10 BTU/hr 14 BTU/hr Physical Parameters Weight 5846 17 oz. 17 oz. 5845 9 oz. 9 oz. Dimensions Inches 5846 4.1W x 5.1L X 1.3H 5845 2.0W x 5.1L X 1.3H Indicators Power Transmit Fiber Transmit Electrical Receive Fiber Receive Electrical Ordering Information Model Input Fiber Type Input Power Rating 5845HRT RS-422/485 Multi-Mode 9-15 Vdc 5846HRT-H RS-422/485 Multi-Mode 90-250Vdc/90-250Vac 5846HRT-L RS-422/485 Multi-Mode 24-48 Vdc 5845SHRT RS-422/485 Single-Mode 9-15 Vdc 5846SHRT-H RS-422/485 Single-Mode 90-250Vdc/90-250Vac 5846SHRT-L RS-422/485 Single-Mode 24-48 Vdc ACC-LCS ACC-CBL1 Link Cantilever Mounting Bracket DB9 Male/Tinned Lead 10 Foot Cable/Pigtail GarrettCom, Inc. 47823 Westinghouse Drive Fremont, CA 94539 PH: (510) 438-9071 FAX: (510) 438-9072 Email: mktg@garrettcom.com Web: www.garrettcom.com
Dymec Serial Links SubStation Hardened 4 Channel RS232 Over Single Fiber Pair Features In most applications, one pair of 5940 links will replace 8 standard links and 3 fiber pairs lowering capital and installation costs. Packaged in rugged, industrialquality Galva Neal and powder coated shells Conformal coated PCBs Powered from Station Battery Bus Operates reliably at temperatures of 40 C to 85 C Extended distances of 5km over Multi-mode fiber and 25km over Single-mode fiber. Multiple Mounting choices with built-in mounting brackets and optional mounting shelf Continuous monitoring of Link Status via status LED or built-in logic annunciator Each channel has its own diagnostic LED s for easier debug when installing Certified to IEEE 1613 and Class 1 Div2 Dymec 5941 and 5942 Data Links are designed as full duplex four channel devices. Four channels have bandwidth of DC to 64k bps (D4 version), and on the (D1 version) three of the channels have bandwidth of DC to 4k bps. Used in point-to-point RS-232 application, 5941 and 5942 Data Links are designed to pass handshaking or flow control signals along with data. These links do not utilize the flow signals for their operation. Like all Dymec digital-to-fiber optic products, they are passive to all software protocols, and simply send the communications signals from one node to the other. Sending four RS-232 non-handshaking signals together on a single pair of fibers (provided at least three of the signals are at 4000 baud or slower for the D1 version). Interfacing RTUs to radios that require push-to talk control Passing up four contacts bi-directionally or KYZ meter contacts. Transmitting data and IRIG-B timing signals with a single Link. 1 or 2 Synchronous data ports (D4 model only). 5941 and 5942 Data Links feature a power-on light, a SYNC LED, and eight diagnostic LEDs.
Specifications Dymec Serial Links--5941/5942 Optical Parameters @ Max Temp Multimode Single-Mode Optical Budget Typical 19.5dB 19dB Output Power Typical -10.5 dbm peak -14.5 dbm peak Receiver Sensitivity Typical -30 dbm peak -33.5 dbm peak (62.5µ/125 Multimode) (9µ/125 Single-mode) Wavelength 850nm 1310nm Connector Type ST Compatible Fiber Type Multimode (50-200µm) Single-Mode (9-13µm) Configuration (Switches) Channel 3 IRIG-B Output/Standard Channel 3 Drive Current Select Channel 4 Sync Indicator/Data Out Data Rate D1 Version DC to 64kbps Channel 1 DC to 4kbps Channels 2,3,4 D4 Version DC to 64kbps all 4 channels Data Transmission Asynchronous, simplex Half or Full Duplex Transmission Distance Up to 5000 meters Up to 30K meters (62.5µ/125 Cable@3dB/km) (9µ/125 Cable@.5dB/km) Bit Error Rate 10-E9 Max. Point to Point Latency 25µS D1 Version Only 100µS Channels 2,3,4 1µS D4 Version Only 12µS Channels 2,3,4 Electrical Parameters Inputs I/O Data Format EIA RS232; CCITT v.24 Data Connector 9 pin D-Type Female Input Impedance >3000Ohms Input voltage +/-30 Volts Max Outputs Output Impedance >300Ohms Driver Output +/-5Volts into 3000Ohms Channel 3 0 to 2.5V @10mA 0 to 3V @ 20mA Ambient Temperature Operating Temperature -40 to +85 C -40 to +70 C Storage Temperature -40 to 85 C Power Required 5942 2.4 Watts 3.6 Watts 35 ma @ 90-250 V 40 ma @ 90-250 V 170 ma @ 18-60 V 200 ma @ 18-60 V 5941 2.4 Watts 3.0 Watts 200mA @ 12Vdc 250mA @ 12Vdc Power Dissipation BTU/H 5942 10.9 BTU/hr 12.3 BTU/hr 5941 8.2 BTU/hr 10.2 BTU/hr Physical Parameters Weight 5941 17 oz. 5942 9 oz. Dimensions Inches 5942 4.1W x 5.1L X 1.3H 5941 2.0W x 5.1L X 1.3H Indicators Power Sync Status Transmit Each Channel Receive Each Channel Ordering Information Model EIA Standard Fiber Type Input Power Rating 64K Baud Data Rate 5941D1HRT RS-232/TTL Multi-Mode 9-15 Vdc 1Channel 5942D1HRT-H RS-232/TTL Multi-Mode 90-250Vdc/90-250Vac 1Channel 5942D1HRT-L RS-232/TTL Multi-Mode 24-48 Vdc 1Channel 5941SD1HRT RS-232/TTL Single-Mode 9-15 Vdc 1Channel 5942SD1HRT-H RS-232/TTL Single-Mode 90-250Vdc/90-250Vac 1Channel 5942SD1HRT-L RS-232/TTL Single-Mode 24-48 Vdc 1Channel 5941D4HRT RS-232/TTL Multi-Mode 9-15 Vdc 4 Channels 5942D4HRT-H RS-232/TTL Multi-Mode 90-250Vdc/90-250Vac 4 Channels 5942D4HRT-L RS-232/TTL Multi-Mode 24-48 Vdc 4 Channels 5941SD4HRT RS-232/TTL Single-Mode 9-15 Vdc 4 Channels 5942SD4HRT-H RS-232/TTL Single-Mode 90-250Vdc/90-250Vac 4 Channels 5942SD4HRT-L RS-232/TTL Single-Mode 24-48 Vdc 4 Channels ACC-LCS ACC-CBL2 Link Cantilever Mounting Bracket DB9 Male/4 DB9 Female 1 X 4 Interface Cable 1 Foot GarrettCom, Inc. 47823 Westinghouse Drive Fremont, CA 94539 PH: (510) 438-9071 FAX: (510) 438-9072 Email: mktg@garrettcom.com Web: www.garrettcom.com