PAGEPAC 6 V INSTALLATION There are several ways to connect PagePac 6 to your telephone system.

Similar documents
Multiple Digital Messaging Unit

MODEL CMX-300. Technical Practice October 2015 Issue 6. Service Observing System 1. GENERAL 2. DESIGN FEATURES 3. OPERATION CONTENTS: Model CMX-300

WIRESPEED ADSL MODEM (MODEL 2000) User Guide

DIAMOND ELITE SERIES USERS GUIDE

This document will show you how to set up the Hotwire 6205 ADSL Modem, and how to customize its configuration to get the most out of this product.

UT3620 Triple NT1 Installation Guide

WS must be used in a temperature controlled place. It is compliant to ETS Class T

SuperBus 2000 Phone Interface/Voice Module Installation Instructions

G.SHDSL NTU with Fixed Serial Interfaces

SuperLine IAD Models 6501, 6502, 6510, 6511, and 6512 Installation Instructions

2GI. Touch Screen Wireless Keypad

AT&T. ZoneMate 3 Service Manual. PagePac 20 Voice Paging System. MERLIN CS Connection And Operation

AREA CODE CHANGE. Please note that the area code for Paradyne Corporation in Largo, Florida has changed from 813 to 727.

Wiring and Cables You May Need (not supplied)

G.SHDSL NTU DECEMBER 2006 LB510A

PagePac PAGEPAC PLUS ZONE EXPANSION UNIT V

888385_01 Install.book Page 1 Wednesday, November 11, :45 PM. SMDR6 Installation Guide

Owner s Instruction Manual

V-9939C MICROPHONE ADAPTER

V-9964 Digital Feedback Eliminator/Message Stacker

V-9939B MICROPHONE ADAPTER

V-9941A ONE ZONE HANDSFREE TALKBACK CONTROL UNIT

CIB 3125 (122A) Off-Premises Range Extender. Installation Instructions. Installed By Qualified Technician Only CIB

USER MANUAL. MODEL 552 Series. High Speed Telco Surge Protectors. SALES OFFICE (301) TECHNICAL SUPPORT (301)

Service Manual For. -IP Voice over Internet Protocol -ACH** Handset cord length Inches

Service Manual For. -IP Voice over Internet Protocol -ACH** Handset cord length Inches

SmartNode 4830 DSL Series Analog VoIP Integrated Access Device Quick Start Guide

V-9964 Digital Feedback Eliminator/Message Stacker

V-9964 Digital Feedback Eliminator/Message Stacker

KS-SB200 BOOM BOX INSTRUCTIONS LVT B [J]

Four IFB. Multi Line Phone Bridge. User Guide. JK Audio. Warranty

4" AMPLIFIED RECESSED CEILING SPEAKERS 8" AMPLIFIED RECESSED CEILING SPEAKERS

HomeWorks Telephone Interface. Instructions for Installation and Use Please Read Before Installing. HWI-TEL9 18 V 60 Hz 300 ma

SERVICE MANUAL FOR MODEL WPP-531-X-ADA-STROBE WEATHERPROOF TELEPHONE WITH OPTIONAL STROBE FEATURE. EQUIPPED WITH SPK1.

SERVICE MANUAL MODEL SSW-321-F MODEL BLW-321-F

SERVICE MANUAL FOR. MODEL MHW-341-Fr1 MAGNETIC HOOKSWITCH WALL TELEPHONE

Photo50 V608 1 ENGLISH

VE8012A/VE8012AR DUAL NETWORKED STATION PORT

Open Applications Interface (OAI) Installation and Setup

SERVICE MANUAL MODEL WPP-331-D WEATHERPROOF TELEPHONE MODEL HOB-331-D WEATHER RESISTANT TELEPHONE. and MODEL SSP-311-D STAINLESS STEEL PANEL TELEPHONE

V CHANNEL MODULAR PRE-AMP/MIXER V-9984 REMOTE INPUT MODULE V CHANNEL MODULAR PRE-AMP/MIXER

VIP-804 QUAD ENHANCED NETWORK AUDIO PORT

SERVICE MANUAL MODEL SSW-321-X

V-9908 MESSAGE/PAGE PANEL

PRODUCT DESCRIPTION SPECIFICATIONS INSTALLATION. Dialer codes PRODUCT DIAGRAM. DL2 Dialer Module Digital Alarm Communicator Transmitter. Warning!

VIP-812A DUAL NETWORKED STATION PORT

IC+ 56k External Data Fax Voice Modem IP568x User s Guide

345 Encinal Street Santa Cruz, CA

OPAL 1010S. The Teledex one-line. speakerphone specifically MANUAL OWNER S. designed for the international. hospitality industry.

SERVICE MANUAL. MODEL SSW-321-Fr1

SERVICE MANUAL MODEL SSC-301-F (FORMERLY 301-FS) MODEL BLC-301-F (FORMERLY 301-F)

GN 4170 headset telephone Hands-free ease with sleek, space-saving phone

SPK User Manual. 900MHz Wireless Stereo Headphones INTRODUCTION FEATURES IMPORTANT SAFETY INFORMATION

BIG BUTTON PHONE WITH ONE TOUCH DIALING AND

Issue 1 3/16/93. PagePac Plus AmpliCenter Installation and Use

PARTNER Contact Closure Adjunct

Cerberus Division. Installation Instructions CERBERUS PYROTRONICS TM Model RDM-MXL. (Remote Diagnostics Module)

User Manual. C Type Power Filter. Model C3 and C3BLK

AudioCast Receiver Owners Manual

SERVICE MANUAL MODEL SSW-321-D

Enclosure TS-530 User Manual

OWNER S INSTRUCTION MANUAL

Big button Speakerphone MODEL: FC-8814

AT&T. PARTNER II Centrex Communications System Release 1 Installation and Use

NT1B-300 Rack Installation Instructions

AudioCast Transmitter Owners Manual

DP-222Q Color Video Door Phone Manual

Telephone Line Monitor USER GUIDE

Setting up your modem s connections

SERVICE MANUAL FOR MODEL SSC-500-F (FORMERLY 501-FSZ) STAINLESS STEEL HANDS FREE CHARGE-A-CALL TELEPHONE EQUIPPED WITH LOW-POWER SPEAKER BOARD

Doc Rev B INSTALLATION INSTRUCTIONS FOR THE "NO PHONE BILL" INTERFACE

VE8014A/VE8014AR QUAD NETWORKED STATION PORT

User Manual. C Type Wall Mount Power Filter C2, C2-CN

Hotwire 5216 RTU Customer Premises Installation Instructions. Before You Begin. Wiring and Cables Needed. Document Number 5216-A2-GN10-20 June 1999

Multiport Analog VoIP Router

Megabit Modem MM300S INSTALLATION GUIDE

QuickTap. JK Audio. Telephone Handset Tap. User Guide

SERVICE MANUAL FOR MODEL WPP-531-D WEATHERPROOF TELEPHONE WITH OPTIONAL ADA FEATURE

SERVICE MANUAL MODEL SSP-550-X (FORMERLY SSP-510-X)

SubCast Transmitter/Receiver Subwoofer Kit

PICTURE PHONE WITH ONE TOUCH DIALING MODEL: FC-0613

RETRO SERIES USER GUIDE. Retro Desk, Retro Wall

6220 and 6225 Telephones Quick Reference

NT1-220 Rack. Installation Instructions. Specifications. Contents of Shipping Box. Important Safety Instructions. NT1-220 Rack

DP-234Q (NTSC) DP-734Q (PAL) Hands-Free Video Door Phone Manual

Clarity P400 TM. Featuring Clarity Power Technology. Clarity P400 User Guide P A ~ F R A N Ç A I S

AT&T. PARTNER Plus Communications System Release 3. Installation

OWNER S INSTRUCTION MANUAL. External Feature Module MODEL 3416

INSTALLATION INSTRUCTIONS FOR THE MINI-KEY SYSTEM. Doc Rev B

DP-222Q Color Video Door Phone Manual

TIF-101 Telephone Interface Installation and Use

Hotwire 5620 RTU Customer Premises Installation Instructions

Hotwire 5620 RTU Customer Premises Installation Instructions. Contents. What Does the Hotwire 5620 RTU Do? Optional POTS Splitter

Allworx Tx 92/24 Telephone Expander Installation Guide

CS-MP125 INSTRUCTION MANUAL. Dual Alarm Clock Radio with Universal Dock for ipod. Please read this manual carefully before operation.

Instruction Manual. for. Audio Ape Remotes. 1

USB Port Hub HO

DVTEL-3100 User's Manual Version 1.0 Revised 1/6/2005 Doc $25.00

Heavy Duty Ringdown/Autodialer Telephone Panel Insert

SERVICE MANUAL FOR MODEL WPP-531-D WEATHERPROOF TELPHONE OR MODEL HOB-531-D WEATHER RESISTANT TELPHONE

Transcription:

PagePac by Issue 2 PAGEPAC 6 V-5323006 INTRODUCTION PagePac 6 is a compact, 6 watt, voice-paging system that integrates single-zone paging capability to your telephone system. Dimensions/Weight 6.0 W x 2.5 H x 3.3 D (15.2cm x 6.4cm x 8.3cm) 2.0 lbs. (0.9 kg) SPECIFICATIONS FEATURES Connects to telephone system through standard modular telephone cords Connects to voice coil speakers or horns Provides a 6-watt, voice coil output Controls background music provided from a line level source Includes 12VAC power supply that plugs into any standard 120VAC, 60 Hz outlet. Connects directly to telephone system page port (Page port must provide a dry contact closure.) Requires separately purchased adapters for telephone systems without page port connections (Trunk Adapter & PagePal) INSTALLATION There are several ways to connect PagePac 6 to your telephone system. For telephone systems equipped with a page port that has a contact closure, the PagePac 6 connects directly to the page port (see Figure 1). NOTE: For those telephone systems not equipped with a page port, a choice of adapters is available. 1 947176

NCOMING ENTRAL OFFICE INES PAGE Page PORT port JACK with cc jack TELEPHONE SYSTEM PAGEPAC 6 SPEAKERS TELEPHONE Figure 1. PagePac 6 Connections to Telephone System Equipped with Page Port and a Contact Closure CONNECTING PAGEPAC 6 TO A PAGE PORT WITH A CONTACT CLOSURE INSTALLATION PROCEDURE PagePac 6 can be placed on a desk or shelf, or wall-mounted using the keyhole slot in the bottom of the unit. Circled numbers in Figure 2 correspond to the steps in the following installation procedures. TELEPHONE SYSTEM PAGE JACK ESD COVERS NOT SHOWN NOTE: Two ESD covers are provided for boththe SPEAKER/MUSIC IN terminal strip, and the AUX connector. Remove these covers prior to installation and replace when installation is complete. TO 120 VAC 60 Hz 4-WIRE MODULAR CORD After selecting a convenient location: Figure 3. Connections to a Page Port with RJ11 Jack Connect the page jack on the PagePac 6 to the telephone system page jack with a modular cord. Note: If the page port has screw-type connections, use a half-modular cord to connect to the page port. The modular end of the cord connects to the PagePac 6 PAGE jack. On the other end of the cord, the green lead to page tip, and the red lead connects to page ring. The black and yellow leads are control leads that connect to a dry contact closure provided by the page port. Plug the PagePac 6 power cord into a standard AC wall outlet. 2 947176

Note: The Canadian equivalent to the RJ11C connector is CA11A. Where applicable, CA11A is to be understood for other references to RJ11C in this manual. CONNECTING PAGEPAC 6 USING A PAGEPAC TRUNK ADAPTER INSTALLATION PROCEDURE After selecting a convenient location: Note: Trunk Adapter connects PagePac 6 to vacant CO line port of telephone system. Circled numbers in Figure 3 correspond to the steps in the installation procedure. 1. Connect the Trunk Adapter modular cord to the PagePac 6 PAGE jack. 2. Connect the Trunk Adapter power cord to the PagePac 6 POWER OUT jack. 3. Connect the Trunk Adapter jack J2 to the telephone system trunk line jack (the jack which will be dedicated for paging) with a standard modular cord. 4. Plug the PagePac 6 power cord into a standard AC wall outlet. PAGE VOL SPKRS PAGEPAC 6 MUSIC PAGE VOL MUSIC IN AUX POWER OUT TRUNK ADAPTER TRUNK ADAPTER MODEL V-5335300 No 22050-900 J1 J2 3 TELEPHONE SYSTEM INCOMING LINE JACK 1 2 TO 120 VAC 60 Hz 4 ESD COVER NOT SHOWN Figure 3. Connections to a Line Jack Using the PagePac Trunk Adapter CONNECTING PAGEPAC 6 USING A PAGEPAL INSTALLATION PROCEDURE After selecting a convenient location: Note: Add PagePal to PagePac 6 installation for Override page access, alert tones, CO port or Station port access, or night bell. 1. Connect terminal 13 of PagePal to green (pin 4) of PagePac 6. 2. Connect terminal 15 of PagePal to red (pin 3) of PagePac 6. 3. Connect terminal 16 of PagePal to yellow (pin 5) of PagePac 6. 4. Connect terminal 17 of PagePal to black (pin 2) of PagePac 6. 3 947176

RINGER COMMON AC/DC NO PRE-ANNC TONE NO CONFIRMOR PRE-ANNCTONE TONE2CHIME TONE1SIREN ATTENDANT ACCESS GROUND C1 RING TIP C Phone System PagePac 6 G R Y B 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 + - + - + - ATTENDANT MUSIC INPUT INPUT 100k OHM OUTPUT 600 OHM 2.5 VMAX 600OHM +10dB MAX PHONE SYSTEM NORMALLY OPEN CONTACTS for REMOTE AMP CONTROL NIGHT BELL INPUT PagePal Figure 4. Connections to a PagePac 6 Using a PagePal CONNECTING SPEAKERS TO PAGEPAC 6 Both standard speakers (indoor cone-type) and horn speakers may be used with PagePac 6. For best performance, use only the type speaker recommended for your situation (see Table 1), and do not exceed the number of speakers or speaker run length maximums shown in Table 2. Table 1. Recommended Speakers Paging Area Mounting Location Speaker Type Valcom Order No. Open or Closed Office Areas, Conference Room, Etc. On Wall or Ceiling Universal Cabinet V-5330105 Above the Ceiling Recessed Ceiling V-5330115 Hallways On Wall or Ceiling Universal Cabinet V-5330105 Private Office Placed on Desk or Wall Desktop or Wall V-5330110 Open Industrial Area or Outdoors On Wall or Pole at Least 15 Ft. Above Ground 1 Watt Horn V-5330010 Table 2. Speaker Limitations Standard Indoor Speakers Horn Speakers Total Speakers 24 @ 1/4W 6 @ 1W Speakers Per Run 1 5 1 Maximum Length of Speaker Run (24 AWG Copper Wire) Maximum Lenght of Speaker Run (22 AWG Copper Wire) 100 Feet 500 Feet 100 Feet 300 Feet Notes: 1. A run is a line of one or more speakers that connects directly to PagePac 6. If using both horns and standard speakers, each horn counts as four standard speakers. In some situations you may be able to extend a run father than 100 feet, by using fewer speakers and/or larger diameter wire. 4 947176

FIRST RUN SPEAKERS SECOND RUN SPEAKERS THIRD RUN SPEAKERS PagePac 6 Figure 5. Connecting Speakers CONNECTING MUSIC SOURCE TO PAGEPAC 6 REQUIRED MATERIALS An external music source, such as FM tuner, tape deck, leased source, etc. Wire for making connection between music source and PagePac 6. Speaker wire (24 AWG) may be used for this purpose. INSTALLATION PROCEDURE 1. Connect audio output of music source (see Figure 6) to the PagePac 6 MUSIC IN terminals. 2. Turn on the music source. 3. Select a station and set the volume control on the music source, then use the MUSIC VOL control on the PagePac 6 to adjust the volume, as described in Operation Section. NOTES: If, during a page, you hear music in the speakers or phone, reverse the position of the wires on the MUSIC IN terminals. 5 947176

2)/- 8 7 5 1+ 8 2)/- 2 9-4 7 6 52 45 7 5 1+ 1 )7: 6 8 ) + $ 0 9 1 4 1 / 5 7 2 2 1 -, * ; 1 5 6 ) - 4 7 5 1 + 5 7 4 + - 5 7 + 0 ) 5. 6 7-4 5 1 / ). 4 7 5 1 + 5 7 4 + - Figure 6. Connections Using an External Music Source Those who use paging systems to rebroadcast copyrighted music are required to obtain licenses from and pay fees to copyright owners. This usually involves obtaining licenses and paying fees to either ASCAP and/or BMI (American Society of Composers, Artists and Producers, Broadcast Music Inc.). It is the user's obligation to obtain any license required and pay any fees. Whenever possible, the PagePac 6 paging system should be plugged into the same AC power receptacle as the voice system. OPERATION Paging procedures differ depending on the requirements of your telephone system and how it is connected to PagePac 6. If your system is connected using a PagePac 6 Port Saver, pay particular attention to the pertinent instruction section below. PAGING WHEN CONNECTED THROUGH A PAGE PORT OR A PAGEPAC TRUNK ADAPTER The exact procedure for paging on your particular telephone system is explained in the user's manual that accompanies the telephone system. In general, though, the steps are as follows: 1. Access the paging function as required by your telephone system. If PagePac 6 is connected through a page port, you will probably push a button or dial a code to access the function. If PagePac 6 is connected through a PagePac Trunk Adapter, you will follow your telephone system's requirements for accessing the line reserved for paging. 2. Make the page. 3. Replace the telephone handset gently (remember you are still connected to the loudspeaker). This will prevent loud noises from being heard over the paging system. ADJUSTING PAGE AND MUSIC VOLUME Volume controls on the rear of PagePac 6 allow you to adjust the volume of paging and background music independently. To adjust paging volume, turn the PAGE VOL control clockwise to increase or counterclockwise to decrease volume. 6 947176

To adjust background music volume, turn the MUSIC VOL control clockwise to increase or counterclockwise to decrease volume. If you do not use background music, turn the MUSIC VOL control fully counterclockwise. Note: PAGE VOL should be adjusted first, then MUSIC VOL. MAINTENANCE The PagePac 6 contains no user-serviceable parts, and should be repaired only by authorized personnel. There are several types of installation and maintenance plans available from Valcom or your dealer. For information or warranty service, call your Valcom sales representative or authorized dealer. TROUBLESHOOTING PROCEDURES If your paging system fails to operate properly, follow the suggestions in the Trouble Analysis Table (see Table 3) before calling for professional assistance. Table 3. Trouble Analysis Table Problem No sound from one or more speakers while others work. Paging and music do not work. Or, music works but paging does not. Paging and music are garbled. Paging works, but music does not. Corrective Action Check volume control on problem speaker(s). Check all connections to speakers. Replace inoperative speaker with good one. If speaker cannot be replaced immediately, wire around it to ensure service to the remaining speakers. NOTE: Look for a mix of voice coil and 70 volt speakers. Replace all 70 volt speakers with voice coil type. Refer to Table 2-1. Ensure that the power supply is plugged in and that the outlet has power. Check the volume controls on the rear of PagePac 6. Check speaker connections. Isolate the source of the problem using a test set. NOTE: Look for a mix of voice coil and 70 volt speakers. Replace all 70 volt speakers with voice coil type. Refer to Table 2-1. If Connected Using a Trunk Adapter 1. Disconnect the Trunk Adapter from the line jack. 2. Connect a 2500-Type telephone to the Trunk Adapter jack J2. 3. If the PagePac 6 is working, you will be able to page using the telephone. Music should also work, and be switched out during a page. Check speaker wire for shorts. Look for staples driven through wire. Check all connections. Ensure music source has power. Adjust PagePac 6 MUSIC VOL control. Adjust volume control on music source. Tune music source to strong station. Check all connections. If, for any reason, you need to know the pinouts for the modular jacks on the PagePac 6, pinout information is given in Tables 4. 7 947176

Table 4. PagePac 6 PAGE Jack Pin 1 Cord Lead 2 Function Connect to Paging Port Notes: 1 Not Used Not Used Not Used 2 Black Access Control (C) Dry Contact Closure (C) 3 Red Ring Ring 4 Green Tip Tip 5 Yellow Access Control (C1) Dry Contact Closure (C1) 6 Not Used Not Used Not Used 1. Pin number from left to right, as seen when looking into jack. TECHNICAL ASSISTANCE When calling, have a VOM and a telephone test set available and call from the job site. Call (540) 427-3900 and ask for PagePac Technical Support, or call (540) 427-6000 for Valcom 24-hour Automated Support or visit our websites at http://www.pagepac.com and www.valcom.com. Should repairs be necessary, attach a tag to the unit clearly stating company name, address, phone number, contact person, and the nature of the problem. Send the unit to: Valcom, Inc. PagePac Repair Dept. 5614 Hollins Road Roanoke, VA 24019-5056 FCC REGULATIONS PERTAINING TO THIS EQUIPMENT FCC (PART 15) Radio Frequency Interference The PagePac 6 generates, and uses radio-frequency energy and, if not installed and used in strict accordance with the manufacturer s instructions, may cause interference to radio and television reception. Testing has been conducted for compliance with the limits for a Class B device in accordance with the specifications in Subpart J of Part 15 of the FCC Rules. This testing is designed to provide reasonable protection against such interference. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio or television reception, which can be determined by turning the PagePac unit off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient the radio or TV receiving antenna. Relocate the PagePac with respect to the radio or TV receiver or vice-versa Plug the PagePac 6 into a different outlet so that it and the radio or TV receiver are on different branch circuits. If necessary, the user should consult the dealer or an experienced radio/television technician for additional suggestions. The user may find the following booklet, How To Identify and Resolve Radio-TV Interference Problems, helpful. This booklet was prepared by the Federal Government printing Office, Washington, DC 20402. Stock order No. 004-000-00345-4. FCC (PART 68) This equipment is registered with the Federal Communications Commission (FCC) in accordance with Part 68 of its Rules. The FCC requires that the manufacturer provide you with the following information: 8 947176

1. Connection and Use with Nationwide Telephone Network The FCC requires that you connect your telephone equipment to the nationwide telephone network through a modular telephone outlet or jack. The modular telephone outlet or jack to which the equipment must be connected is a USOC RJ11C. Registered equipment may not be used with Coin Telephone Lines. Equipment may be used with Party Lines in areas where state tariffs permit such connections and when equipment is adaptable for such use. 2. Information You May Need to Supply the Telephone Company Upon request of your local telephone company, you are required to provide them with the following information. A. The lines to which you will connect the telephone equipment. Note: In Canada, the Document Registration Number appears on the maple-leaf label and the Load Number is under the maple-leaf label. B. The FCC registration number and Ringer Equivalence Number (REN). Both numbers are listed on the equipment label. The REN is useful to determine how many devices you may connect to your telephone line and still have them ring when your telephone lines is called. In most, but not all, areas, the sum of all RENs per line should be 5 or less. You may want to contact your local telephone company. The local telephone company must also be notified upon final disconnection of the equipment from the local telephone company lines. CSA REGULATIONS PERTAINING TO THIS EQUIPMENT This product is UL Listed and CSA Certified. NOTICE: The Canadian Department of Communications label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective operational and safety requirements. The Department does not guarantee the equipment will operate to the user s satisfaction. Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications company. The equipment must also be installed using an acceptable method of connection. In some cases, the company s inside wiring associated with a single line individual service may be extended by means of a certified connector assembly (telephone extension cord). The customer should be aware that compliance with the above conditions may not prevent degradation of service in some situations. Repairs to certified equipment should be made by an authorized Canadian maintenance facility designated by the supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give the telecommunications company cause to request the user to disconnect the equipment. 9 947176

Users should ensure for their own protection that the electrical ground connections of the power utility, telephone lines and internal metallic water pipe system, if present, are connected together. This precaution may be particularly important in rural areas. CAUTION: User should not attempt to make such connections themselves, but should contact the appropriate electric inspection authority, or electrician, as appropriate. SECONDARY CIRCUIT PROTECTION IMPORTANT INFORMATION This equipment is for use on telephone wiring containing a secondary circuit protector. This paging equipment requires a secondary circuit protector where applicable (see Figure 7). The secondary circuit protector must be located between the primary protector and the paging equipment. Refer to the Safety Information below. Figure 7. Example Configuration Requiring Secondary Protection When Paging Equipment is Connected Directly to the Telephone Network SAFETY INFORMATION The secondary circuit protector is used when connecting paging equipment directly to telephone lines that may be exposed to high voltage power lines. Never install telephone wiring during a lightning storm. Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations. Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface. Use caution when installing or modifying telephone lines. Use appropriate Valcom approved device. 10 947176