Measuring instruments

Vernier calipers 26804 Stainless steel - DIN 862 Range Jaw Nonius /inch 135 40 1/20-1/128 160 40 1/20-1/128 180 40 1/20-1/128 Until end of stock 26808 Stainless steel, chrome satin finish - DIN 862 Range Jaw Nonius /inch 135 45 1/20-1/128 160 45 1/20-1/128 200 45 1/20-1/128 300 60 1/20-1/128 160 45 1/50-1/1000 200 45 1/50-1/1000 300 60 1/50-1/1000 26808020 Calipers for left hand Range Nonius Jaw 10103 160 1/20-1/128 40 Mit Calipers Range Nonius Jaw 530-104 0-150 1/128 x 0,05 on 39 40 530-114 0-200 1/128 x 0,05 on 39 50 530-115 0-300 1/128 x 0,05 on 39 64 530-312 0-150 1/1000 x 0,02 on 49 40 530-118 0-200 1/1000 x 0,02 on 49 50 530-119 0-300 1/1000 x 0,02 on 49 64 530-102* 0-150 0,05 on 39 40 * Setscrew 531-316 0-150 1/128 x 0,05 on 39 40 530-319 0-150 0,05 on 39 40 * Thumblock 531-122 0-150 1/128 x 0,05 on 39 40 531-108 0-200 1/128 x 0,05 on 39 50 531-109 0-300 1/128 x 0,05 on 39 64 * Carbide Jaws 530-320 0-150 0,05 on 39 40 530-321 0-200 0,05 on 39 50 530-322 0-300 0,05 on 39 64 530-335** 0-150 0,05 on 39 40 * With depth gauge, ø 19 ** Inside-outside carbide measuring surfaces SET SCREW UP THUMB LOCK CARBIDE JAWS E 1

Calipers High capacity calipers Satined stainless steel - DIN 862 - Nonius : 1/50-1/128 Range Utile range Jaws 300 250 200 65 301 300 250 80 303 450 400 150 304 550 500 150 305 650 600 150 306 850 800 150 307 1050 1000 150 High capacity calipers DIN 862 Satined stainless steel - DIN 862 fine adjustement Range Utile range Jaws Range Utile range Jaws 1/50 1/20 1/50 1/20 1/128 1/128 1/128 1/128 650 13350 250 200 65 669 13367 850 800 300 651 13351 300 250 80 697 13368 850 800 400 652 13399 300 250 125 670 13369 1050 1000 150 653 13352 350 300 90 671 13370 1050 1000 200 654 13353 350 300 150 672 13371 1050 1000 300 655 13386 450 400 90 673 13372 1050 1000 500 992 13354 450 400 125 674 13390 1250 1200 150 656 13355 450 400 150 994 13373 1250 1200 200 657 13356 450 400 200 999 13374 1250 1200 300 658 13357 550 500 115 675 13375 1550 1500 150 659 13358 550 500 150 996 13376 1550 1500 200 660 13359 550 500 200 676 13377 1550 1500 300 661 13360 550 500 250 677 13378 1550 1500 500 662 13361 650 600 115 678 13380 2050 2000 300 663 13362 650 600 150 679 13381 2050 2000 500 664 13363 650 600 200 997 13382 2550 2500 200 665 13387 650 600 250 680 13383 2550 2500 300 666 13364 650 600 300 998 13384 3050 3000 200 667 13365 850 800 150 681 13385 3050 3000 300 668 13366 850 800 200 High capacity calipers with points range DIN 862 Range Jaws Range Jaws 1/50 1/20 1/50 1/20 1/128 1/128 1/128 1/128 750 13450 200 65 765 13467 800 300 751 13451 250 80 757 13469 1000 150 752 13487 300 90 766 13470 1000 200 758 13486 400 125 767 13471 1000 300 753 13455 400 150 768 13473 1200 200 759 13456 400 200 769 13474 1200 300 754 13458 500 150 770 13476 1500 200 760 13459 500 200 771 13477 1500 300 761 13460 500 250 772 13479 2000 200 755 13462 600 150 773 13480 2000 300 762 13463 600 200 774 13482 2500 200 763 13464 600 300 775 13483 2500 300 756 13465 800 150 776 13484 3000 200 764 13466 800 200 777 13485 3000 300 E 2

Calipers 22302 Dial caliper Range Reading Jaws 491/2 100 0,02 = 1/50 30 490 150 0,05 = 1/20 40 491 150 0,02 = 1/50 40 492 150 0,01 = 1/100 40 491/3 200 0,02 = 1/50 50 492/4 200 0,01 = 1/100 50 492/5 300 0,01 = 1/100 60 491/1 300 0,02 = 1/50 60 Dial caliper Guidance titanium coated. Wear resistant and easy moving (up to measuring range 200 ) High precision Easy to read Measuring scale satin chrome finished All parts made from corrosion-free steel. MIT Serie 505 Measuring range Graduation Jaw length Error limits L a b c d e Mass g 0-150 505-685* 0,01 40 0,03 231 40 21,0 16,5 16 57,2 176 0-150 505-671 0,02 40 0,03 231 40 21,0 16,5 16 57,2 175 0-150 505-711*** 0,02 40 0,03 231 40 21,0 16,5 16 57,2 175 0-200 505-686* 0,01 50 0,03 288 50 24,5 20,0 16 57,2 186 0-200 505-672 0,02 50 0,03 288 50 24,5 20,0 16 57,2 185 0-300 505-673* 0,02 64 0,04 403 64 27,5 22,0 20 70,2 370 * 1 rotation of needle = 1 Particularly easy reading of 0,01 ** Without titanium coating *** Surfaces of external and interior measurement out of carbide 505-685 22303001 Electronic digital calipers Range 0-150 Nonius (-inch) 0,01 / 0,0005 Accuracy ± 0,03 Jaws 40 With LCD output E 3

Calipers DIGIMATIC MIT Serie 500 Standard design DIN 862, without data output Measuring range Coents 0-150 500-181-21 With extension for depth measurement 231 40 21,0 16,5 16 164 0-200 500-182-21 With extension for depth measurement 288 50 24,5 20,0 16 194 L a b c d Mass g 500-181-21 MIT Serie 500 DIN 862 Standard design, without data output, with round depth gauge Measuring range 0-150 500-184-21 Coents with round depth gauge ø 1,9 L a b c d Mass g 231 40 21 16,5 16 164 MIT Serie 500 DIN 862, standaard design in a great many versions, with data output Measuring range Drive roller Depth gauge Round extension (depth measuring ø 1,9 ) /inch conversion Carbide-tipped measuring surfaces for outside measurement Carbide-tipped measuring surfaces for inside measurement 0-100 500-150-20 137 0-150 500-161-21 164 0-150 500-151-21 164 0-150 500-158-20 164 0-150 500-171-21 164 0-150 500-154-20 164 0-150 500-155-20 164 0-200 500-162-21 194 0-200 500-152-21 194 0-200 500-172-21 194 0-200 500-156-20 194 0-200 500-157-20 194 0-300 500-153 350 Mass g 500-184-21 500-161-21 Measuring range L a b c d 0-100 180 40 21,0 16,5 16 0-150 231 40 21,0 16,5 16 0-200 288 50 24,5 20,0 16 0-300 403 64 27,5 21,8 20 E 4

DIGIMATIC calipers E ABSOLUTE DIGIMATIC solar caliper Digital measurement without battery ABSOLUTE system for reliable measurement. Optimum caliper sliding properties. Serie 500 Super Caliper DIN 862 Protection IP-67 Extremely resistant to coolants and lubricants Impact-resistant design Serie 500 DIN 862 with data output 500-772-1 500-444 500-457 Serie 500 DIN 862 without data output Measuring range MIT Coents Protection IP-67 Data output L a b c d 0-150 500-772-1-233 40 21,0 16,5 16 176 Mass g 0-200 500-773-1-290 50 24,5 20,0 16 206 0-150 500-778-1-233 40 21,0 16,5 16 176 0-200 500-779-1-290 50 24,5 20,0 16 206 0-150 500-444 0-200 500-445 with drive roller with drive roller 231 40 21,0 16,5 16 170 288 50 24,5 20,0 16 200 0-150 500-457 - 231 40 21,0 16,5 16 150 0-200 500-458 - 288 50 24,5 20,0 16 180 551-201-20 551-231-10 Serie 551 With knife-shaped measuring surfaces for outside measurement and with rounded measuring surfaces for the measurement of inside dimensions. With data ouput. Measuring range Inside measurements Error limits L a b c d Mass g 0-200 551-201-20 10 0,03 290 60 8 30 16 196 0-300 551-231-10* 10 0,04 403 90 10 40 20 420 0-500 551-204-10 20 0,06 680 150 18 56 25 1060 0-750 551-206-10 20 0,06 963 150 18 56 25 1410 0-1000 551-207-10 20 0,07 1230 150 20 56 32 3430 * With OFFSET function for direct reading in the case of inside measurements With PRESET function for storing 2 preset values. E 5

Digital Calipers 550-201-20 550-231-10 Serie 550 With rounded measuring surfaces for the measurement of inside dimensions with data output Measuring range Inside measurements Error limits L a b c Mass g 0-200 550-201-20 10 0,03 290 60 8 16 186 0-300 550-231-10* 10 0,03 403 75 12 20 380 0-450 550-203-10 20 0,05 630 100 18 25 1110 0-600 550-205-10 20 0,05 780 100 18 25 1290 0-1000 550-207-10 20 0,07 1240 140 24 32 3350 * With OFFSET function for direct reading in the case of inside measurements With PRESET function for the storage 2 preset values. Rounded measuring surfaces for the measurement of inside dimensions Sample application E 6

Digital Calipers ABSOLUTE DIGIMATIC Caliper acc. to protection rating IP-66 and IP-67 Characteristics : Spray-water protected for heavy-duty work with coolants and lubricants. ABSOLUTE system for reliable measurement. Extremely resistant to coolants and lubricants. Optimum caliper sliding properties. Digital Caliper IP-66 The IP 66 digital caliper with integrated absolute scale meets the most stringent safety specifications according to DIN EN 60 529 against dust and strong hose water. For example, it will easily withstand a strong water jet flowing at a rate of 100 litres per minute from any direction, for at least three minutes. Digital Calipers IP-67 The IP-67 digital calliper extends the moisture protection of the IP-66 version with a further feature : it will even withstand temporary complete iersion in water or coolant, without suffering any damage. 500-626-1 500-706-1 MIT Measuring range Resolution Error limits Depth gauge Data output Mass g IP-66 0-150 500-626-1 0,01 DIN 862 Flat 164 0-200 500-627-1 0,01 DIN 862 Flat 194 0-300* 500-628 0,01 DIN 862 Flat 345 0-150 500-637-1 0,01 DIN 862 Flat 164 0-200 500-638-1 0,01 DIN 862 Flat 194 0-300* 500-639 0,01 DIN 862 Flat 345 0-150 500-657-1 0,01 DIN 862 Round ø 1,9 164 IP-67 0-150 500-706-1 0,01 DIN 862 Flat 164 0-200 500-707-1 0,01 DIN 862 Flat 194 0-150 500-716-1 0,01 DIN 862 Flat 164 0-200 500-717-1 0,01 DIN 862 Flat 194 0-150 500-709-1 0,01 DIN 862 Round ø 1,9 164 * no Tüv certification Measuring range a b c d e 0-150 21,0 16,5 231 40 16 0-200 24,5 20,0 288 50 16 0-300 28,0 21,8 408 64 20 Accessories Basis for depth gauge a b c d e 050083 25 75 24,5 9 16 050084 25 100 24,5 9 16 Battery 938882 SR44 050084 050083 Cable of connexion 959149 SPC 1 m 959150 SPC 2 m 959143 Unite HOLD 050084 E 7

Outside micrometer 25904 Outside micrometer DIN 863/1 Carbide tipped faces Range 0-25 25-50 50-75 75-100 100-125 125-150 150-175 175-200 26014 Outside micrometers with exchangeable anvils for large range DIN 863/1 Reading 0,01 - Carbide tipped faces Range 300-400 400-500 500-600 600-700 700-800 800-900 900-100 1000-1200 1200-1400 1400-1600 1600-1800 1800-2000 Setting standard for outside micrometer Range ø Range ø Range ø 25 7 250 8 675 8 50 7 275 8 725 8 75 7 325 8 775 8 100 8 375 8 825 8 125 8 425 8 875 8 150 8 475 8 925 8 175 8 525 8 975 8 200 8 575 8 225 8 625 8 Set of outside micrometers Range Pcs 3410 0-100 4 7065 0-150 6 7069 0-300 12 Micrometer holders ART. COD. Basis S26 3640 80 x 120 E 8

Depth gauge E Satined stainless steel Satined stainless steel - Reading : 1/50 Range Basis 2270 150 80 2271 200 80 2272 250 80 2273 300 80 2274 400 80 Depth gauge, double use Satined stainless steel - Reading : 1/20 Range Basis 2310 150 80 2311 200 80 2312 250 80 2313 300 80 2314 400 80 Depth gauge with needle Satined stainless steel - Reading : 1/20 Range Basis 13550 150 105 13551 200 105 13552 250 125 13553 300 105 13554 300 150 13555 500 150 Depth gauge with screw of regulating Satined stainless steel - Reading : 1/50 Range Basis 2250 200 150 2251 250 150 2252 350 150 2253 450 150 2277 160 80 2276 250 80 DIGIMATIC ABSOLUTE depth gauges Electronic caliper with built-in absolute scale. One-time setting of origin that remains as the absolute zero position until the battery has to be changed. Extraordinary precision even with high speed movement. Large display digits are easy to read. Optimum caliper sliding properties. MIT Serie 571 - with data output Measuring range Error limits L Mass g 0-150 571-201-10 0,03 237 200 0-200 571-202-10 0,03 287 220 0-300 571-203-10 0,04 403 260 0-450 571-204-10 0,05 635 1270 0-600 571-205-10 0,05 785 1400 0-750 571-206-10 0,06 935 1530 0-1000 571-207-10 0,07 1200 1760 IP-67 0-150 571-251 0,03 237 365 0-200 571-252 0,03 287 408 571-201-10 571-251 E 9

Outside micrometer Outside micrometer Serie 103 - Light-weight workshop design Specifications Graduation : 0,01 Scales : thimble and sleeve satin chrome finish, Measuring spindle : spindle pitch 0,5 with spindle lock Measuring surfaces : carbide-tipped, precision ground and micro-lap finish Frame : enamelled Measuring force : 5-10 N (from 100 : 5-15 N) Including box, gauge block (from 25-600 ), up to 50 with factory certificate, key Meas. range. L a b c Mass g Accuracy : DIN 863-1 0-25 103-137 30,3 2,8 9 28 175 25-50 103-138 55,3 2,8 10 38 215 50-75 103-139-10 80,3 2,8 12 49 315 75-100 103-140-10 105,3 2,8 14 60 375 100-125 103-141-10 132,8 5,3 17 79 515 125-150 103-142-10 158,2 5,7 19 94 665 150-175 103-143-10 183,6 6,1 20 106 720 175-200 103-144-10 208,8 6,3 19 118 920 200-225 103-145-10 234,2 6,7 18 130 1080 225-250 103-146-10 258,0 5,5 18 143 1255 250-275 103-147-10 284,0 6,5 18 156 1405 275-300 103-148-10 309,0 6,5 18 169 1565 300-325 103-149 353,0 18,0 28 187 1985 325-350 103-150 378,0 18,0 28 199 2155 350-375 103-151 403,0 18,0 28 212 2305 375-400 103-152 428,0 18,0 28 224 2455 400-425 103-153 453,0 18,0 28 236 2715 425-450 103-154 478,0 18,0 28 248 2965 450-475 103-155 503,0 18,0 28 261 3215 475-500 103-156 528,0 18,0 28 273 3450 Accuracy : Factory specification, Error limits : (1+L/75) µm L in 500-525 103-157 575,0 40,0 28 307 4060 525-550 103-158 575,0 15,0 28 307 4080 550-575 103-159 625,0 40,0 28 332 4500 575-600 103-160 625,0 15,0 28 332 4525 Friction thimble; Accuracy : DIN 863-1 0-25 103-125 30,3 2,8 9 28 175 25-50 103-126 55,3 2,8 10 3 215 103-137 103-125/103-126 Friction thimble Digital outside micrometers DIN 863 IP54 Reading : 0,0001 / 0,00005 inch - Carbide tipped faces Range 0-25 25-50 50-75 75-100 100-125 125-150 150-175 175-200 E 10

«DIGIMATIC» Micrometer E Digital standard external screw type micrometer with IP-65 protection. Serie 293 with data output Resolution : 0,001 Scales : thimble and sleeve satin chrome finish Measuring surfaces : carbide-tipped, precision ground, micro-lap finish Frame : enamelled Measuring force : 5-10 N Including box, key, 1 battery, gauge block from 25 and up to 50 measuring range with factory certificate. Optional accessories : - O5CZA662 - Signal cable with data key (1 m) - O5CZA663 - Signal cable with data key (2 m) Consumable Spares : - 938882 - Battery SR-44 Measuring range Error limit* µm L a b c Mass g With ratchet (standard version) 0-25 293-230 2-2,8 9,0 25,0 270 25-50 293-231 2 25,0 2,8 9,8 32,0 330 50-75 293-232 2 50,0 2,8 12,6 47,0 470 75-100 293-233 3 75,0 2,8 14,0 60,0 625 100-125 293-250 3 132,8 5,3 16,7 76,5 600 125-150 293-251 3 158,2 5,7 18,8 91,0 740 150-175 293-252 4 183,6 6,1 19,1 103,1 800 175-200 293-253 4 208,8 6,3 18,2 115,3 970 200-225 293-254 4 234,2 6,7 16,8 126,8 1100 225-250 293-255 5 258,0 5,5 18,0 139,8 1270 250-275 293-256 5 284,0 6,5 18,0 152,3 1340 275-300 293-257 5 309,0 6,5 18,0 166,0 1540 With ratchet thimble 0-25 293-234 2-2,8 9,0 25,0 270 25-50 293-235 2 25,0 2,8 9,8 32,0 330 50-75 293-236 2 50,0 2,8 12,6 47,0 470 75-100 293-237 3 75,0 2,8 14,0 60,0 625 With friction thimble 0-25 293-238 2-2,8 9,0 25,0 270 Set Contents : 0-50 293-966 293-230, 293-231 0-75 293-962 293-230, 293-231, 293-232 0-100 293-963 293-230, 293-231, 293-232, 293-233 * Accuracy exceeding the requirements of DIN 863 «DIGIMATIC» Micrometer Serie 293 DIN 863-1 with data output External screw type micrometer with 1 pitch to avoid reading errors. With large measuring surfaces Specifications with ratchet thimble Accuracy : according to DIN 863-1 Resolution : 0,001 Scales : thimble and sleeve satin chrome finish, Ø 21,5 Measuring surfaces : carbide-tipped, precision ground, micro-lap finish Steigung : 1 Measuring force : 5-10 N Including box, gauge block (from 25-50 ), insulation, key, 1 battery Optional accessories 937387 Signal cable (1m) 965013 Signal cable (2m) Consumable Spares 938882 Battery SR-44 Measuring range L a b c Mass g 0-25 293-151-30 31,8 2,8 7 26 320 25-50 293-152-30 56,8 2,8 7 33 390 50-75 293-153-30 81,8 2,8 10 48 530 75-100 192-154-30 106,8 2,8 11 61 670 Serie 293 «Quick» external screw type micrometer in standard version With non-rotating spindle Measuring Error limit Flatness Parallelism Measuring a b x Mass range µm µm µm force N g 0-30 293-661-10* 2 < 0,3 < 2,0 5-10 9,0 25-275 0-30 293-666 2 < 0,3 < 2,0 5-10 9,0 25-275 25-55 293-667 3 < 0,3 < 2,0 5-10 11,3 36 25 355 50-80 293-668 3 < 0,3 < 2,0 5-10 13,1 47 50 525 75-105 293-669 3 < 0,3 < 2,0 5-10 13,5 60 75 625 * without data output 293-230 Measuring range up to 0-100 293-661-10 ABSOLUTE scale with origin point Scale 293-238 With ratchet (standard version) Ratchet thimble Friction thimble Measuring range up to 100-300 Rapid adjustment Detector Spindle pitch 10/U 293-151-30 Micrometer has a newly developed spindle mechanism enabling a spindle drive of 10/U anda measuring range of 30. The drive rate is therefore 20 x higher than in conventional micrometers. E 11

Outside micrometer Serie 340 «DIGIMATIC» Type, with data output DIN 863-1, Form D16 Specifications Protection class : IP-65 (Measuring rande up to 300 ) Accuracy : DIN 863-1 ab 500 Factory specification Error limit : ± (4 + L/75) µm; L in Resolution : 0,001 Scales : thimble and sleeve satin chrome finish, Ø 18 (up to 300 ) Ø 21 (over 300 ) Measuring spindle Ø 6,35 (up to 300 ) Ø 8 (over 300 ) spindle pitch 0,5, with spindle lock Measuring surfaces : hardened, precision ground Frame : light weight construction, enamelled Measuring force : 5-10 N (10-14 N for measuring rage over 300 ) Including box, standards, measuring inserts, key, 1 battery Optional accessories 05CZA662 Signal cable (1m)(for devices up to 300 Measuring range) 05CZA663 Signal cable (2m)(for devices up to 300 Measuring range) 937387 Signal cable (1m)(for devices from 300 Measuring range) 965013 Signal cable (2m)(for devices from 300 Measuring range) Consumable Spares 938882 Battery SR-44 Measuring range Inserts Protection IP-65 Standards Mass kg 0-150 340-251 6 5 0,96 150-300 340-252 6 6 1,88 300-400 340-513 4-4 3,31 400-500 340-514 4-4 4,81 500-600 340-515 4-4 6,35 600-700 340-516 4-4 7,72 700-800 340-517 4-4 9,08 800-900 340-518 4-4 10,41 900-1000 340-519 4-4 11,78 340-251 Special outside micrometers Prec.-blade micrometers, DIN 863/1 Measuring range Point Measuring range Point 0-25 0,75 x 6,5 50-75 0,75 x 6,5 25-50 0,75 x 6,5 75-100 0,75 x 6,5 Serie 422 «DIGIMATIC» type, with data output DIN 863, Form D4 Specifications Accuracy : DIN 863-1 Resolution : 0,001 Scales : thimble and sleeve satin chrome finish, Ø 18 Measuring spindle : Ø 6,35, spindle pitch 0,5 Frame : enamelled Measuring force : 3-8 N Including box, gauge block (from 25 ), insulation, key, 1 battery Optional accessories 05CZA662 Signal cable (1m) 05CZA663 Signal cable (2m) Consumable Spares 938882 Battery SR-44 Measuring range Mass g Measuring range Mass g Type A 0-25 422-230 365 50-75 422-232 465 25-50 422-231 565 75-100 422-233 580 Type B 0-25 422-260 365 25-50 422-261 565 422-230 E 12

Special outside micrometers Prec.-micrometers with small measuring face, DIN 863/1 For measuring of splined shafts or slots, with small measuring face ø 2 x 5, spindle ø 6,5, reading 0,01, in wooden case Range Point Range Point 0-25 Ø 2 x 5 25-50 Ø 2 x 5 E Serie 331 «DIGIMATIC» type, with data output DIN 863, Form D 3 Specifications Protection class : IP-65 Accuracy : DIN 863-1 Resolution : 0,001 Scales : thimble and sleeve satin chrome finish, Ø 18 Measuring spindle : Ø 6,35, spindle pitch 0,5, with spindle lock Measuring surfaces : carbide-tipped, precision ground, micro-lap finish, stepped Frame : enamelled Measuring force : 5-10 N Including box, gauge block (25-75 ), key, 1 battery Optional accessories 05CZA662 Signal cable (1m) 05CZA663 Signal cable (2m) Consumable Spares 938882 Battery SR-44 Measuring range l/d Mass g 0-25 331-251 10/3 330 25-50 331-252 10/3 470 50-75 331-253 10/3 625 75-100 331-254 10/3 565 0-25 331-261 5/2 330 25-50 331-262 5/2 470 50-75 331-263 5/2 625 75-100 331-264 5/2 565 331-251 Tube micrometer Ground thread, measuring faces convex, thred pitch 0,5, reading 0,01, with ratchet, spindle 6,5 ø, in case Measuring range 0-25 Serie 395 Tube micrometer Special version «DIGIMATIC» Type, with data output DIN 863, Form D1 (Type A, B) Form similar to D12 (types C, D, E, F) For measurements of all curved surfaces and wall thickness of tubes, bearings, rings, etc. Specifications Protection class : IP-65 Accuracy : DIN 863-1 (type A, B) Factory specification Error limit : 3 µm (type C, D, E, F) Resolution : 0,001 Scales : thimble and sleeve satin chrome finish, ø 18 Measuring spindle ø 6,35, spindle pitch 0,5, with spindle lock Measuring surfaces : carbide-tipped, precision ground, micro-lap finish Frame : enamelled Measuring force 5-10 N, 3-8 N Including box, gauge block (from 25-100 ), key, 1 battery Optional accessories 05CZA662 Signal cable (1m) 05CZA663 Signal cable (2m) Consumable Spares 938882 Battery SR-44 Measuring Error range limits µm L min. ød a Mass g 0-25 395-251 2-15 9 270 25-50 395-252 2-15 9,8 330 50-75 395-253 2-19 12,6 470 75-100 395-254 3-20 14 625 0-25 395-271 2-15 9 270 25-50 395-272 2-15 9,8 330 50-75 395-273 2-19 12,6 470 75-100 395-274 3-20 14 625 395-251 E 13

Special outside micrometers Serie 112 Analogue version Point type micrometer special version With pointed spindle For measuring grooves, steps etc. Specifications Accuracy : Factory specification (2+L/75 )µm - L in Lecture : 0,01 Scales : thimble and sleeve satin chrome finish, ø 18 Measuring spindle : ø 6,35, spindle pitch 0,5, with spindle lock Measuring surfaces hardened and precision ground conical spindle and anvil, measuring point radius 0,3 Frame : enamelled Measuring force : 5-10 N Including box, gauge block (25-100 ), key 112-201 Measuring range L a b c ød Mass g Angle : 15 0-25 112-153 55,3 12,8 10 38 6,35 205 25-50 112-154 80,3 12,8 12 49 6,35 305 Angle : 30 0-25 112-201 55,3 12,8 10 38 6,35 205 25-50 112-202 80,3 12,8 12 49 6,35 305 Serie 342 «DIGIMATIC» type, with data output Specifications Protection class: IP-65 Accuracy : Factory specification - Error limit (2+L/75) µm - L in Resolution : 0,001 Scales : thimble and sleeve satin chrome finish, ø 18 Measuring spindle : ø 6,35, spindle pitch 0,5, with spindle lock Measuring surfaces : hardened and precision ground conical spindle and anvil, measuring point radius 0,3 Frame : enamelled Measuring force : 5-10 N Including box, gauge block (25-75 ), key, 1 battery Optional accessories 05CZA662 Signal cable (1m) 05CZA663 Signal cable (2m) Consumable Spares 938882 Battery SR-44 342-251 Measuring range Mass g Angle : 15 0-25 342-251 330 25-50 342-252 470 50-75 342-253 625 75-100 342-254 565 Angle : 30 0-25 342-261 330 25-50 342-262 470 50-75 342-263 625 75-100 342-264 565 E 14

Special outside micrometers E Special outside micrometers DIN 863 without anvils Measuring range 0-25 50-75 25-50 75-100 Setting standard Measuring range 25 (60 ) 25 (55 ) 50 (60 ) 50 (55 ) 75 (60 ) 75 (55 ) Screw anvils metric 60 (UNF) Art.- M 106/2 Pitch 0.4-0.5 3.5-5.0 0.6-0.9 5.5-7.0 1.0-1.75 0.4-7.0 (set) 2.0-3.0 Screw anvils whitworth WHITWORTH 55 Pitch 60-48 14-10 48-40 10-7 40-32 7-4.5 32-24 4.5-3.5 24-18 60-3.5 (set) 18-14 Serie 326 «DIGIMATIC» type, with data output DIN 863, Form D18 Specifications Protection class : IP-65 Accuracy : DIN 863-1 Resolution 0,001 Scales : thimble and sleeve satin chrome finish, ø 18 Measuring spindle : ø 6,35, spindle pitch 0,5, with spindle lock Frame : enamelled Measuring force : 5-10 N Including box, gauge block (60 ), insulation, key, 1 battery MEASURING INSERTS NOT INCLUDED Optional accessories 05CZA662 Signal cable (1m) 05CZA663 Signal cable (2m) Consumable Spares 938882 Battery SR-44 Measuring inserts 55 Mass g Length (Optional acc.) Measuring range 60 (Standard acc.) 0-25 326-251 350 25 167-272 167-261 25-50 326-252 380 50 167-273 167-262 50-75 326-253 470 75 167-274 167-263 75-100 326-254 510 100 167-275 167-264 326-251 Serie 126/326 Optional accessories measuring inserts Metric UNF tums/inch pitch Individual measuring inserts Whitworth tums/inch Individual measuring inserts Whitworth tums/inch 126-801 0,4-0,50 64,0-48,0 126-811 60-48 126-816 18,0-14,0 126-802 0,6-0,90 44,0-28,0 126-812 48-40 126-817 14,0-10,0 126-803 1,0-1,75 24,0-14,0 126-813 40-32 126-818 10,0-7,0 126-804 2,0-3,00 13,0-9,0 126-814 32-24 126-819 7,0-4,5 126-805 3,5-5,00 8,0-5,0 126-815 24-18 126-820 4,5-3,5 126-806 5,5-7,00 4,5-3,5 Measuring insert set Measuring insert set 126-800 (consist of 126-801 to 126-806) 126-810 (consist of 126-811 to 126-820) E 15

Special outside micrometers Prec.-three-fluted-micrometers, DIN 863/1 for checking 3 sidemills, with carbide tipped measuring faces, spindle ø 6,5, reading 0,01, in case Range Accuracy Range Accuracy 1-15 0.004 50-65 0.006 5-20 0.004 65-80 0.006 20-35 0.004 80-95 0.006 35-50 0.005 Serie 314 «DIGIMATIC» type, with data output DIN 863, Form D 10-3 Specifications Accuracy : DIN 863-1 Resolution : 0,01 Scales : thimble and sleeve satin chrome finish, ø 18 Measuring spindle : ø 6,35, spindle pitch 0,75, with spindle lock Measuring surfaces : Prism angle 60 Broche : enamelled Measuring force : 5-10 N 3-8 N (314-251, 314-261) Including box, gauge block, key, 1 battery (gauge blocks : see above) Optional accessories 05CZA662 Signal cable (1m) 05CZA663 Signal cable (2m) Consumable Spares 938882 Battery SR-44 Measuring range Mass g Measuring surfaces with grooves 1-15 314-251 275 10-25 314-252 410 25-40 314-253 465 Measuring surfaces without grooves 1-15 314-261 275 10-25 314-262 410 Prec.-gear tooth-micrometers DIN 863/1 for measuring of gear tooth, with disc measuring face, no-rotating spindle ø 6,5, reading 0,01, in case Range Disc Range Disc 0-25 20 100-125 30 25-50 20 125-150 30 50-75 20 150-175 30 75-100 20 175-200 30 314-251 314-252 Serie 369 «DIGIMATIC» type, with data output DIN 863, Form D6 Specifications Accuracy : DIN 863-1 Resolution : 0,01 Scales : thimble and sleeve satin chrome finish, ø 18 Measuring spindle : ø 6,35, spindle pitch 0,5, with spindle lock Frame : enamelled Measuring force : 3-8 N Including box, gauge block (25-100 ), insulation, key, 1 battery Optional accessories 05CZA662 Signal cable (1m) 05CZA663 Signal cable (2m) Consumable Spares 938882 Battery SR-44 Measuring Measuring Mass g range range Mass g 0-25 369-250 340 50-75 369-252 635 25-50 369-251 480 75-100 369-253 775 369-250 E 16

Special outside micrometers E 26202 Tube micrometer Ground thread, measuring faces convex, thread pitch 0,5, reading 0,01, throat 27,5, with ratchet, spindle 6,5 ø, in case Range 0-25 Accuracy 0,01 26203 Micrometers for rolling mills Range Depth of frame 0-15 35 0-15 50 26205 Micrometer for wires DIN 862 Reading 0,01 Range 0-10 Serie 157 Optical parrallel For testing surface flatness and parallelism of measuring surfaces of outside micrometers. Specifications Flatness : 0,1 µm Parallelism : 0,2 µm Diameter : 30 Range of outside micrometer Nominal 0-25 157-903 12,00 ; 12,12 ; 12,25 ; 12,37 25-50 157-904 25,00 ; 25,12 ; 25,25 ; 25,37 157-903 158-118 Serie 158 Optical glas flat For testing surface flatness Specifications Flatness : 0,1 µm Nominal Diameter 158-118 12 45 158-120 15 60 Direction du regard Surface de mesure concave Verre plan Touche fixe Surface de mesure convexe Verre plan Touche fixe E 17

Depth micrometer Serie 128 Depth micrometer Fixed version without exchangeable measuring inserts Specifications Accuracy : DIN 863-2 Graduation : 0,01 Scales : thimble and sleeve satin chrome finish, ø 18 Measuring span : 25 Rod : ø 4 Spindle pitch : 0,5, with spindle lock Measuring surfaces : hardened, precision ground, micro-lap finish Base : hardened tool steel Flatness : 60 : 1,3 µm 100 : 2µm Measuring force : 5-10 N Including box, key Measuring range Base Error limits micrometers 0-25 128-101 60 x 16 3 µm 0-25 128-102 100 x 16 3 µm 128-101 Serie 129 Version with exchangeable measuring inserts Rods hardened Specifications Accuracy : DIN 863-2 Scales : thimble and sleeve satin chrome finish, ø 18 Measuring span : 25 Rod : ø 4 Spindle pitch : 0,5, with spindle lock Measuring surfaces : hardened, precision ground, micro-lap finish Base : hardened tool steel Flatness : 60 : 1,3 µm 100 : 2 µm Measuring force : 5-10 N Including box, key Measuring range Base Number of rods 0-50 129-109 60 x 16 2 3 µm 0-75 129-110 60 x 16 3 3 µm 0-100 129-111 60 x 16 4 3 µm 0-150 129-112 60 x 16 6 3 µm 0-300 129-152 60 x 16 12 3 µm 0-50 129-113 100 x 16 2 3 µm 0-75 129-114 100 x 16 3 3 µm 0-100 129-115 100 x 16 4 3 µm 0-150 129-116 100 x 16 6 3 µm 0-300 129-153 100 x 16 12 3 µm Error limits micrometers 129-112 Serie 329 Depth micrometer «DIGIMATIC» version with data output and exchangeable measuring inserts Specifications Accuracy : Factory specification Resolution : 0,001 Scales : thimble and sleeve satin chrome finish, ø 18 Measuring span 25 Rod : ø 4 Spindle pitch : 0,5, with spindle lock Measuring surfaces : hardened, precision ground, micro-lap finish Base : hardened tool steel Flatness Base : 2 µm Tolerance of interchangeable ± (2+L/75) µm measuring inserts : L = measuring length in Error limit with «zero» measuring inserts : 5 µm Measuring force : 5-10 N Including box, key, battery Optional accessories 05CZA662 Signal cable (1m) 05CZA663 Signal cable (2m) Consumable Spares 938882 Battery SR-44 329-250 Measuring range Base Number of rods Error limits micrometers 0-150 329-250 100 x 16 6 3 µm 0-300 329-251 100 x 16 12 3 µm E 18

Inside micrometers E 26301 Precision inside micrometers DIN 863/1, reading 0,01 thread lead 0,5 - Hardened faces Range 25-30 30-35 35-50 50-75 75-100 100-125 125-150 150-175 175-200 200-225 225-250 250-275 275-300 26207 Inside micrometers DIN 863/1 with extension Reading : 0,01 Carbide faces Thread lead : 0,5 Range 50-150 50-850 50-250 50-1250 50-450 50-1450 Inside micrometers Satin chrome reading 0,01 - Carbide faces 27405 27406 Range 5-30 25-50 50-75 75-100 100-125 125-150 27405 Inside micrometers Satin chrome reading 0,01 Carbide faces Range 5-30 25-50 50-75 75-100 100-125 125-150 Serie 148 Micrometer heads with lock, especially suited for fine adjustments Specifications Accuracy : Factory specification Stem : With/without adjustment nut Measuring Graduation Error Mass range limit g Coents 0-13 148-103 0,01 0,002 35 with adjusting nut 148-104 0,01 0,002 35 without adjusting nut 148-801 0,01 0,002 35 spherical measuring surface, without adjusting nut 148-802 0,01 0,002 35 spherical measuring surface, with adjusting nut 13-0 148-821 0,01 0,002 35 reversable scale, without adjusting nut 148-822 0,01 0,002 35 reversable scale, with adjusting nut 148-104 E 19

Inside micrometers Three point inside micrometer Range Accuracy Depth 3460 3,5-4,0 0,001 20 3461 4,0-4,5 0,001 20 3462 4,5-5,5 0,001 20 3463 5,5-6,5 0,001 20 3464 6-8 0,001 50 3465 8-10 0,001 50 3466 10-12 0,001 50 3467 12-16 0,005 60 3468 16-20 0,005 60 3469 20-25 0,005 80 3470 25-30 0,005 80 3471 30-35 0,005 80 3472 35-40 0,005 80 3473 40-50 0,005 90 3474 50-60 0,005 90 3475 60-70 0,005 90 3476 70-80 0,005 90 3477 80-90 0,005 90 3478 90-100 0,005 90 3479 100-125 0,005 140 3480 125-150 0,005 140 3484 150-175 0,005 140 3485 175-200 0,005 140 3486 200-225 0,005 140 3492 225-250 0,005 140 3493 250-275 0,005 140 3495 275-300 0,005 140 Set three point inside micrometers Range Composition Extensions 3487 3,5-6,5 1 x 3,5-4 1 x 4-4,5 1 x 4,5-5,5 1 x 5,5-6,5 3488 6-12 1 x 6-8 1 x 8-10 1 x 10-12 3489 12-20 1 x 12-16 1 x 16-20 3490 20-40 1 x 20-25 1 x 25-30 1 x 30-35 1 x 35-40 3491 40-100 1 x 40-50 1 x 50-60 1 x 60-70 1 x 70-80 1 x 80-90 1 x 90-100 1 x 100 1 x 150 1 x 150 1 x 150 Extension for three p.inside micrometers Extension 3496 100 6-12 3497 150 12-20 3497 150 20-40 3497 150 40-100 E 20

Inside micrometer E Three point inside micrometer Holtest Serie 368 Analogue Delivered with factory certificate Specifications Accuracy : DIN 863/4* * The given precision values require close contact of the measuring surfaces. Graduation : up to 12 : 0,001 / over 12 : 0,005 Scales : thimble and sleeve satin chrome finish, up to 12 : Ø 17 / over 12 : Ø 23 Measuring spindle : spindle pitch 0,5 Including box, key, factory certificate Measuring surfaces titanium-coated or carbide. Carbide taper and contact point. Measuring surfaces and tapers, hardened steel. Contact surfaces and points are carbide-tipped. Measuring Depth without Depth with range extensions extensions Mass g Measuring surfaces titanium-coated or carbide. Carbide taper and contact point. 6-8 368-101-10* 59 159 60 8-10 368-102-10* 59 159 60 10-12 368-103-10* 59 159 60 12-16 368-164 80 230 150 16-20 368-165 80 230 160 20-25 368-166 90 240 260 25-30 368-167 90 240 280 30-40 368-168 98 248 290 40-50 368-169 98 248 330 50-63 368-170 105 255 440 62-75 368-171 105 255 450 75-88 368-172 105 255 570 87-100 368-173 105 255 580 100-125 368-174 158 308 1030 125-150 368-175 158 308 1120 150-175 368-176 158 308 1210 175-200 368-177 158 308 1320 200-225 368-178 158 308 1430 225-250 368-179 158 308 1550 250-275 368-180 158 308 1700 275-300 368-181 158 308 1870 * Measuring surfaces up to 12 carbide Measuring Depth without Depth with range extensions extensions Mass g Measuring surfaces and tapers, hardened steel. Contact surfaces and points are carbide-tipped. 12-16 368-764 80 230 150 16-20 368-765 80 230 150 20-25 368-766 90 240 260 25-30 368-767 90 240 280 30-40 368-768 98 248 290 40-50 368-769 98 248 330 50-63 368-770 105 255 440 62-75 368-771 105 255 450 75-88 368-772 105 255 560 87-100 368-773 105 255 570 100-125 368-774 158 308 1020 125-150 368-775 158 308 1110 150-175 368-776 158 308 1200 175-200 368-777 158 308 1300 200-225 368-778 158 308 1420 225-250 368-779 158 308 1540 250-275 368-780 158 308 1690 275-300 368-781 158 308 1860 368-1XX 368-7XX Extensions for series 368/468/568 Length For measuring range Mass g 952322 100 6-12 13 952621 150 12-20 100 952622 150 20-50 238 952623 150 50-300 264 952623 E 21

Inside micrometer Three point inside micrometer Holtest Analogue in sets. Delivered with factory certificate. Serie 368 Specifications Measuring surfaces titanium-coated or carbide. Carbide taper and contact point. Measuring surfaces and tapers, hardened steel. Contact surfaces and points are carbide-tipped. Measuring range Set Contents Device Setting ring Setting ring Ø Extensions Measuring surfaces as well as other wearing parts are carbide-tipped. 6-12 368-901-10 102-10/368-103-10 368-101-10/368-177-125/177-126 8/10 952322 100 Serie 368 Measuring Length of the extensions range Set Contents Device Setting ring Setting ring Ø Extensions Measuring surfaces titanium coated as well as other wearing parts are carbide. 12-20 368-912 368-164/368-165 177-177 16 952621 150 Length of the extensions Measuring range Set Contents Device Setting ring Setting ring Ø Extensions Length of the extensions Measuring surfaces and taper, hardened steel. Contact surfaces and points are carbide-tipped. 12-20 368-991 368-764/368-765 177-177 16 952621 150 Serie 368 Measuring range Set Contents Device Setting ring Setting ring Ø Extensions Measuring surfaces titanium coated as well as other wearing parts are carbide. 20-50 368-913 368-166/368-167 177-139/177-290 25/40 952622 150 368-168/368-169 Length of the extensions Measuring range Set Contents Device Setting ring Setting ring Ø Extensions Length of the extensions Measuring surfaces and taper are hardened steel. Contact surfaces and points are carbide-tipped. 20-50 368-992 368-766/368-767 177-139/177-290 25/40 952622 150 368-768/368-769 368-901-10 368-912 368-913 Three point inside micrometer Holtest Analogue in sets. Delivered with factory certificate. Serie 368 Specifications Measuring surfaces titanium-coated or carbide. Carbide taper and contact point. Measuring surfaces and tapers, hardened steel. Contact surfaces and points are carbide-tipped. Measuring range Set Contents Device Setting ring Setting ring Ø Extensions Measuring surfaces titanium coated as well as other wearing parts are carbide. 50-100 368-914 368-170/368-171 177-314/177-318 62/87 952623 150 368-172/368-173 Length of the extensions Measuring range Set Contents Device Setting ring Setting ring Ø Extensions Length of the extensions Measuring surfaces and taper are hardened steel. Contact surfaces and points are carbide-tipped. 50-100 368-993 368-770/368-771 177-314/177-318 62/87 952623 150 368-772/368-773 Serie 368 Measuring range Set Contents Device Setting ring Setting ring Ø Extensions Measuring surfaces titanium coated as well as other wearing parts are carbide. 100-200 368-915 368-174/368-175 177-298/177-302 125/175 952623 150 368-176/368-177 Length of the extensions Measuring range Set Contents Device Setting ring Setting ring Ø Extensions Length of the extensions Measuring surfaces and taper are hardened steel. Contact surfaces and points are carbide-tipped 100-200 368-994 368-774/368-775 177-298/177-302 125/175 952623 150 368-776/368-777 368-914 368-915 E 22

Inside micrometer E Three point inside micrometer DIGIMATIC-Holtest with exit of data - Serie 468 Specifications Accuracy : DIN 863/4 Resolution : 0,001 6 digitled display Functions : PRESET ZERO setting Weak battery alarm Automatic switch off Range Depth without extensions Depth with extensions Weight g 6-8 468-131 45 145 400 8-10 468-132 45 145 400 10-12 468-133 45 145 400 12-16 468-134 76 226 430 16-20 468-135 76 226 430 20-25 468-136 88 238 500 25-30 468-137 88 238 510 30-40 468-138 102 252 510 40-50 468-139 102 252 530 50-63 468-140 105 255 650 62-75 468-141 105 255 660 75-88 468-142 105 255 990 87-100 468-143 105 255 1000 100-125 468-144 151 301 970 125-150 468-145 151 301 1060 150-175 468-146 151 301 1150 175-200 468-147 151 301 1240 200-225 468-148 151 301 1330 225-250 468-149 151 301 1420 250-275 468-150 151 301 1510 275-300 468-151 151 301 1600 * Carbide taper and contact point 468-145 Keys of function 468-133 468-137 Three point inside micrometer DIGIMATIC-Holtest in set - Serie 468 Specification Range Set Contents Setting ring 6-12 468-961 468-131/132/133 Ø 8,10 12-25 468-962 468-134/135/136 Ø 16,20 25-50 468-963 468-137/138/139 Ø 30,40 50-75 468-964 468-140/141 Ø 62 75-100 468-965 468-142/143 Ø 87 Accessories : 937387 Signal cable (1m) 965013 Signal cable (2m) Spares : 938882 Battery SR-44 468-963 E 23

Inside micrometer «ABSOLUTE» BOREMATIC Three point inside micrometer with data output- Serie 568 Specifications LCD display : 6 digit may be rotated by 330 Resolution : Accuracy : Measuring surfaces Power supply : Functions : 0,001 Norm factory Error limit : 0,005 (Meas. range 6-20 ) 0,006 (Meas. range 20-125 ) La précision implique que les faces à mesurer adhèrent parfaitement à l appareil. carbide Battery SR-44 on/off switching Range Weight g 568-331 6-8 480 568-332 8-10 485 568-333 10-12 485 568-334 12-16 475 568-335 16-20 480 568-336 20-25 540 568-337 25-30 555 568-338 30-40 565 568-339 40-50 610 568-346 50-63 / 62-75 780 568-347 75-88 / 87-100 850 568-348 100-113 / 112-125 970 Range 568-347 568-338 568-339 Accessories 937387 Signal cable (1m) 965013 Signal cable (2m) 952322 Extension 100 (for Borematic with a range 6-12 ) 952621 Extension 150 (for Borematic with a range 12-20 ) 952622 Extension 150 (for Borematic with a range 20-50 ) 952623 Extension 150 (for Borematic with a range 50-125 ) Spares 938882 Battery SR-44 «ABSOLUTE» BOREMATIC three point inside micrometers in sets - Serie 568 Range Setting ring Weight kg 568-971 6-12 ø 8, 10 0,6 568-972 12-25 ø 16, 20 0,8 568-973 25-50 ø 30, 40 1,3 568-975 50-100 ø 62, 87 3,5 568-973 E 24

Dial gauges Dial gauge Range Scale Graduation ø dial 24401012 0-10 0-100 0,01 57 24401013 with fixing lug 0-10 0-100 0,01 57 2046 SB 0-10 0-100 0,01 57 2046 S with fixing lug 0-10 0-100 0,01 57 2109-SB10 1 0-100 0,001 57 2109-S10 1 0-100 0,001 57 24401012 2046SB 24406 Dial gauges with small and big dial Range Reading dial ø ø 40 ø 80 ø 100 ø 150 3,5 0,01 - - - 5 0,01 - - - 10 0,01-30 0,01-50 0,01-80 0,01-24406 Dial gauges with needle indicators Range Scale Reading 2971 0,5 25-0 - 25 0,01 2972 1,5 50-0 - 50 0,01 2972 Dial test indicators Range Scale Reading 513.404 E 0,8 0-40 - 0 0,01 513.405 E 0,2 0-100 - 0 0,002 513.415 E 1 0-50 - 0 0,01 513.474 E Ruby ball 0,8 0-40 - 0 0,01 513.415E E 25

Dial gauges Dial test indicators Divisions Range ø dial Range per turn M 3 S M 2/30 S 703-008 ø 40 KM 4X 0,01 3 40 0,5 KM 4/5 X 0,01 5 40 0,5 ø 58 M2X 0,01 10 58 1 M3 T 0,01 5 58 0,5 M2/30 T 0,01 30 58 1 M2/50 T 0,01 50 58 1 M2/80 T 0,01 80 58 1 M3AT 0,005 5 58 0,5 FM 500 T 0,002 1 58 1 ø 80 GM 80 T 0,01 10 80 1 GM 80/30 T 0,01 30 80 1 GM 80/50 T 0,01 50 80 1 GM 80/100 T 0,01 100 80 1 GM 100/80 T 0,001 1 80 1 ø 100 GM 100 T 0,01 10 100 1 GM 100/30 T 0,01 30 100 1 GM 100/50 T 0,01 50 100 1 ø 150 GM 150 T 0,01 10 150 1 Without fixing lug M 2/50 T E 26

Dial gauges E Dial test indicators Flat back Divisions Range ø Dial Range per turn ø 40 KM 4 XS* 0,01 3 40 0,5 KM 4/5 XS 0,01 5 40 0,5 ø 58 M 2 XS* 0,01 10 58 1 M 2/30 S 0,01 30 58 1 M 2/50 S 0,01 50 58 1 ø 80 GMS 80 S* 0,01 10 80 1 * Shock protected Dial gauges water proof-schock protected Divisions Range ø Dial Range per turn ø 40 KM 4 SW 0,01 3 44 0,5 KM 500 SW 0,002 1 44 0,5 ø 61 M 2 SW 0,01 10 61 1 FM 1000 SW 0,001 1 61 1 Dial gauges with magnetic back Divisions Range ø Dial Range per turn ø 40 KM 4T Magnet 0,01 3 40 0,5 ø 58 M 2 T Magnet 0,01 10 58 1 Horizontal dial gauges Divisions Range ø Dial Range per turn ø 40 KM 4 R 0,01 3 40 0,5 KM 4/5 R 0,01 5 40 0,5 ø 58 M 2 R 0,01 3 58 1 0,01 5 58 1 M 3 S M 3 a S KM 4 SW KM 4T Magnet E 27

Lever indicators Lever type dial test indicators Type Model Space Length Range ø dial Graduations to of a scale 2 ø DIN 2270 K 30 0,01 0,8 32 0-40-0 A 12 K 31 0,01 0,8 32 0-40-0 B 12 K 32 0,01 0,8 32 0-40-0 C 12 K 33 0,01 0,5 32 0-25-0 A 35 K 34 0,01 0,5 32 0-25-0 B 35 K 35 0,01 0,5 32 0-25-0 C 35 K 36 0,002 0,2 32 0-100-0 A 12 K 37 0,002 0,2 32 0-100-0 B 12 K 38 0,002 0,2 32 0-100-0 C 12 K 40 0,01 0,8 40 0-40-0 A 12 K 41 0,01 0,8 40 0-40-0 B 12 K 42 0,01 0,8 40 0-40-0 C 12 K 43 0,01 0,5 40 0-25-0 A 35 K 44 0,01 0,5 40 0-25-0 B 35 K 45 0,01 0,5 40 0-25-0 C 35 K 46 0,002 0,2 40 0-100-0 A 12 K 47 0,002 0,2 40 0-100-0 B 12 K 48 0,002 0,2 40 0-100-0 C 12 K 40/2 0,02 2 40 0-100-0 A 35 Verticel Horizontal Model Cote Serie 30 (32 ø) Serie 40 (40 ø) A, B, C D 32 40 A, B, C E 5,6 6 A G 7,1 7,5 B G 7,7 8,1 C G 7,5 7,9 B H 69,5 73,5 Accessories 2.4804 ø 4 h 6 2.4801 ø 8 h 6 5.2281 5.2297 5.2282 5.2283 5.2296 Carbide pin ø 2 m (Standards models : K 30 - K 32, K 36 - K 42, K 46 - K 48) Carbide pin ø 0,4 Carbide pin ø 1 Carbide pin ø 3 Ruby pin ø 2 5.2284 5.2285 5.2286 5.2298 Carbide pin ø 2 (Standards models K 33 - K 35, K 43 - K 45; K 40/2) Carbide pin ø 1 Carbide pin ø 3 Ruby pin ø 2 Key 1.0956 Spigot ø 8 H7 E 28

Dial gauges E Digital dial gauge Range Resolution 22322001 0-20 0,001 22322002 0-25 0,001 ABSOLUTE DIGIMATIC dial gauge IDC Digital dial gauge in practical, multifunction design. Precise measurement even at high rates of travel Graphic display when tolerances are exceeded or fallen below Incremental value 0.001 or 0.01 With data output Optional accessories Designation 905338 Signal cable (1 m) 905409 Signal cable (2 m) Measuring range Incremental value Error limits 543-250 B 12,0 0,001 0,003 543-450 B 25,0 0,001 0,003 543-460 B 50,0 0,001 0,006 543-270 B 12,0 0,01 0,02 543-250 B ABSOLUTE DIGIMATIC dial gauge IDS and IDU Standard design for easy use. Integral absolute scale. Precise measurement even at high rates of travel Compact installation With data output Optional accessories Designation 905338 Signal cable (1 m) 905409 Signal cable (2 m) 575-121 Measuring range Incremental value Error limits 575-121 25,0 0,01 0,02 543-681 B 12,7 0,01 0,02 ABSOLUTE DIGIMATIC dial gauge ID-F Digital dial gauge with visual tolerance monitoring with colour display and analogue indicator Maximum/minimum hold value, difference (TIR) External power supply with mains adapter supplied Tolerance function with colour display With data output Optional accessories Designation 936937 Signal cable (1 m) 965014 Signal cable (2 m) 543-551D Measuring range Incremental value Error limits 543-551 D 25 0,001 / 0,01 0,003 543-553 D 50 0,001 / 0,01 0,006 E 29

Dial gauges ID-H Dial gauge Top-of-the-range multifunction dial gauges High accuracy with small incremental values Option for external control and external relaying of data Digimatic and RS 232-C interface Maximum/minimum hold value, difference (TIR) Analogue display External power supply with mains adapter supplied With data output Tolerance function with colour display Optional accessories Designation 936937 Signal cable (1m) 965014 Signal cable (2m) 21EZA099 Remote control Measuring range Incremental value Error limits µm 543-561 D 30 0,001 / 0,0005 2 543-563 D 60 0,001 / 0,0005 3 Tolerance function with colour display Hold value difference (TIR) Remote control ABSOLUTE DIGIMATIC coolant-proof dial gauges IDB and IDN Electronic multifunctional dial gauges with intelligent installation concept and innovatie display. Specially for installation in devices where space is restricted Two versions with display for frontal or top reading Flexible installation options with switchable orientation of display With data output Graphic display when tolerances are exceeded or fallen short of Optional accessories Designation 21EAA194 Signal cable (1 m) 21EAA190 Signal cable (2 m) 21EAA210 Signal cable for remote control preset / zero (1 m) 21EAA211 Signal cable for remote control preset / zero (2 m) Range Incremental value Error limits Version 543-580 5 0,01 0,02 (type B) reading from above 543-585 5 0,001 / 0,01 0,003 / 0,01 (type B) reading from above 543-570 12,7 0,01 0,02 (type N) front reading 543-575 12,7 0,001 / 0,01 0,003 / 0,01 (type N) front reading 543-575 (Type ID-N) 543-580 (Type ID-B) Type ID-B Type ID-N E 30

Dial gauges E ABSOLUTE DIGIMATIC dial gauge IDC for control options Digital dial gauge with internal and external control options With «probe» signal input and «open collector» signal output «External» power supply mode : DC 12-24 Ve, ±10% external Ideal for installation in all kinds of system Range Resolution Accuracy µm 543-280 B 12,7 0,001 3 Internal control measuring instrument DIN 878 Delivered without dial Range Accuracy Depth measuring Measuring faces pcs. 15-35 0,01 175 7 Extensions rods 30-100 0,01 250 5 25 + 50 50-160 0,01 250 6 25 + 25 50-210 0,01 380 6 25 + 2 x 25 100-300 0,01 350 6 50 + 100 100-500 0,01 650 6 50 + 3 x 100 190-1000 0,03 650 6 50 + 3 x 100 + 2 x 200 15-210 0,01 175-380 7 25 + 2 x 55 ABSOLUTE DIGIMATIC dial gauge IDC for bore gauges Multifunctional gauge for two-point bore gauges Easy determination of reversal point by through-oscillation The actual value is captured by the peak-hold function and can be read off directly With data output Measuring range Incremental value Error limits µm 543-264 B 12,7 0,001 3 E 31

Bore gauges sets Bore gauges sets With key of steel measure fixed unilaterally. Mobile stem at spherical head in carbide. Specifications Measuring range : 18-150 Mass : 954 g Serie 511 With analogue dial indicator, graduation 0,01 511-901 With dial indicator 2046 SB With analogue dial indicator, graduation 0,001 511-902 With dial indicator 2109 SB-10 With digital dial indicator, resolution 0,001 511-905 With dial indicator 543-264 B E 32

Stand for dial indicators E 24408003 Stand for dial indicators Magnetic base 50 x 55 x 63 Column Ø 12 x 176 Arm Ø 10 x 150 Dial shank 8 Universal dial indicator holder Serie 7 With measuring V-block. Specifications Magnetic force : 600 N vertical retractile force Base size : 50 x 60 x 55 Bore for dial indicator stem : Ø 9,5 Standard accessory 206983 Bushing for dial indicators with shaft Ø 8 Optional accessory 206979 300 cross arm (for 7010 SN only) Working radius ca. Total height Mass kg Without fine adjustment 7010 SN 150 235 1,25 With fine adjustment 7011 SN 160 235 1,45 Universal dial indicator holder Serie 7 With measuring V-block and flexible column. Specifications Magnetic force : 750 N vertical retractile force Base size : 50 x 60 x 55 Bore for dial indicator stem : Ø 9,5 Standard accessory 206983 Bushing for dial indicators with shaft Ø 8 Working radius ca. Total height Mass kg 7012 250 393 1,5 E 33

Precision dial bench gauges Fine gauge stand Serie 215 With wear-resistant hard rock table Specifications Column : ø 30 Base size : 120 x 180 (215-150 M) 150 x 200 (215-151 M) Throat : 65 Bore for dial indicator stem : ø 8 Fine adjustment : 1 Table flatness : 3 µm Max. measuring height Measuring table Mass kg 215-150 M 120 120 x 180 5,7 215-151 M 260 150 x 200 8,0 Serie 215 Wear-resistant hard rock table With threaded column, without fine adjustment Specifications Threaded column : ø 50 Table dimensions : 300 x 150 Base size : 250 x 300 Throat : 90 Bore for dial indicator stem : ø 20 (ø8 / ø15 over bushing) Table flatness : 6 µm Standard accessory 58AAA151 Bushing ø 8 Optional accessory 58AAA276 Bushing ø 15 Max. measuring height Measuring table Mass kg 215-156 300 300 x 250 29,5 215-151 M 215-156 The details in brackets relate to 215-150 M Fine gauge stand Serie 912 Hard rock, fine diamond-lapped measuring table Arm with 120 projection Specifications Column : Usable measuring surface : Base size : Throat : Bore for dial indicator stem : Fine adjustment : ø 35 200 x 140 260 x 140 x 50 120 ø 8 8 Table flatness : 2 µm Max. measuring height Mass kg 912-105 200 9,5 Serie 912 Hard rock base With cross arm and fine adjustment Specifications Column : ø 16 Cross arm : ø 16 Usable measuring surface : 100 x 100 Base size : 150 x 100 x 40 Throat : 150 (adjustable) Bore for dial indicator stem : ø 8 Table flatness : 2 µm Max. measuring height Mass kg 912-101 180 2,8 912-105 912-101 Dial gauge stand Serie 7 Standard version with large table Cast base; measuring table made of hardened steel with lapped surface. Specifications Column : ø 30 Table dimensions : 90 x 90 Base size : 168 x 110 Throat : 65 Bore for dial indicator stem : ø 8 Fine adjustment : 1 Max. measuring height Mass kg 7007 M 90 5,6 7007 M E 34

Quick thickness gauges E Quick thickness gauges Capacity 0-25 0-50 Measuring depth 50 50 Resolution 0,1 0,1 25108 Jaws A ø 3,5 25109 Jaws B ø 10 25110 Jaws C ø 25 25110 Capacity 0-25 0-25 0-25 0-25 Measuring depth 150 300 450 600 Resolution 0,1 0,1 0,1 0,1 25111 Jaws ø 6 25112 Jaws ø 10 25113 Jaws ø 25 25111 Quick thickness gauges Serie 7 Light-weight construction, with analogue dial indicator Measuring resolution Max. measuring Error Parallelism range depth limits µm Dial indicator avec surfaces de mesure plate en céramique 0-1 7327 0,001 30 0,005 < 5 2109 SB-10 0-10 7301 0,01 30 0,020 < 5 2046 SB 0-20 7305 0,01 30 0,025 < 5 2050 SB Quick thickness gauges ABSOLUTE DIGIMATIC Unique thickness gauge equipped with the ABSOLUTE DIGIMATIC dial indicator ID-C The origin is set only once and is stored as the absolute origin until the battery is replaced. Measuring precision even at highest drive speed. Large display characters for easy reading. Light-weight construction. Serie 547 Disk probe tips made of ceramics ( 547-301), With adjustable anvil ( 547-313), With knife-shaped probe tip ( 547-315) Optional accessory 905338 Signal cable (1 m) 905409 Signal cable (2 m) Consumable Spares 938882 Measuring range Battery SR-44 Max. measuring Error Parallelism Dial Resolution depth limits µm indicator With disk probe tips made of ceramics 0-10 547-301 0,01 30 0,02 < 5 543-270 B Quick thickness gauges ABSOLUTE DIGIMATIC Unique thickness gauge equipped with the ABSOLUTE DIGIMATIC dial indicator ID-C The origin is set only once and is stored as the absolute origin until the battery is replaced. Measuring precision even at highest drive speed. Large display characters for easy reading. Light-weight construction. Serie 547 With large jaw capacity and disk probe tips made of ceramics Optional accessory 905338 Signal cable (1 m) 905409 Signal cable (2 m) Consumable Spares 938882 Measuring range Battery SR-44 Resolution Max. measuring depth Error limits Parallelism µm Dial indicator With disk probe tips made of ceramics 0-10 547-321 0,01 120 0,02 < 5 543-270 B 7327 7313 547-301 547-315 547-321 E 35

Thickness measuring instruments Reading 0,1 Capacity 20 Measuring depth 50 Measuring faces Rubber, soft materials K 50 K 50/3 K 100 Loving leather, cardboard, paper, Liège Hard leather, isorel, plywood Sheeting, steel, metals Reading... 0,1 Range... 10 Measuring depth... 50 Reading... 0,1 Range... 30 Measuring depth... 50 Reading... 0,1 Range... 30 Measuring depth... 100 Reading () Range () Measuring depth () Reading () Range () Measuring depth () K50 0,1 10 50 According K50/5 0,1 50 50 K50 with level 0,1 10 50 to choice K 100 0,1 30 100 K 200 0,1 30 200 a, b, c, d or e K50/2 0,1 20 50 K 300 0,1 30 300 K50/3 0,1 30 50 K 400 0,1 30 400 According to choice a, b, c, d or e Quick thickness gauge «QUICK MINI» Serie 700 «QUICK MINI» is a Digimatic quick thickness gauge without data output Specifications Resolution : 0,01 Character height : 7,5 Max. measuring force : 2 N Power supply : Battery SR-44 Battery life : appr. 2 years Error limits : 0,02 Including box Repetability : 0,01 Consumable Spares Display : LCD, 5 digit with sign (-) 938882 Battery SR-44 700-119 700-121 Measuring range Mass g Measuring range Mass g 0-12 700-119 70 0-25 700-121 120 E 36

Dial caliper gauge for inside measurement E Dial caliper gauge for inside measurement SR=0,1 HM = Kø1,0, HM-Kø0,6 K=Radius, S=Knife ID 0302 ID 0305 ID 0705 ID 0710 ID 0720 ID 0730 ID 0740 Measuring range Awb () 2,5-7,5 5-10 5-15 10-20 20-30 30-40 40-50 Range Meb () 5 5 10 10 10 10 10 Graduation Skw () 0,005 0,005 0,01 0,01 0,01 0,01 0,01 Error limit f M () ± 0,01 ± 0,01 ± 0,02 ± 0,02 ± 0,02 ± 0,02 ± 0,02 Repetability F w () 0,0025 0,0025 0,005 0,005 0,005 0,005 0,005 Measuring depth L () 10 22 30 50 52 57 57 Groove depth A () 0,7 2,2 1,7 4 4 4,5 4,5 Groove width B () 0,6 1,4 1,1 2 2 2 2 Measuring contact D () SR 0,1 ➀ Kø0,6 ➁ SR 0,1 ➀ K ø1 ➂ K ø1 ➂ K ø1 ➁ K ø1 ➁ Packaging *1732/01 *1732/01 *1732/01 *1732/01 *1732/01 *1732/01 *1732/01 Serie ID 10 Intertest ID 1010 ID1020 ID1030 ID1040 ID1050 ID1060 ID1070 Measuring faces Measuring range () 10-30 20-40 30-50 40-60 50-70 60-80 70-90 Range () 20,0 20,0 20,0 20,0 20,0 20,0 20,0 graduation () 0,010 0,010 0,010 0,010 0,010 0,010 0,010 Repetability () 0,010 0,010 0,010 0,010 0,010 0,010 0,020 Measuring depth «L» () 80,0 80,0 80,0 80,0 80,0 80,0 80,0 Groove depth «A» () 4,5 6,0 6,0 6,0 6,0 6,0 6,0 Groove width «B» () 1,8 2,5 2,5 2,5 2,5 2,5 2,5 Measuring contact () 1,0 ➀ 1,0 ➀ 1,0 ➀ 1,0 ➁ 1,0 ➁ 1,0 ➁ 1,0 ➁ Measuring contact length «Hb» () 5,0 7,0 7,0 10,0 10,0 10,0 10,0 Measuring contact length «Hf» () 5,0 7,0 7,0 10,0 20,0 10,0 20,0 Measuring contact width «S» () 1,3 1,9 1,9 2,5 2,5/4,0 2,5 2,5/4,0 Balk in metal of ø 1,0 Balk in metal of ø 1,0 Balk in metal of ø 1,0 Balk in metal of ø 2,0 E 37

Dial caliper gauge for outside measurement Dial caliper gauge for outside measurement OD0305 OD0305T OD0710 OD0710S OD0710R OD0710RS Measuring range Awb () 0-5 0-5 0-10 0-10 0-10 0-10 Range Meb () 5 5 10 10 10 10 Graduation Skw () 0,005 0,005 0,01 0,01 0,01 0,01 Error limit f M () ± 0,01 ± 0,02 ± 0,02 ± 0,02 ± 0,02 ± 0,02 Repetability F w () 0,0025 0,005 0,005 0,005 0,005 0,005 Measuring depth L () 28 28 59 59 59 59 Measuring faces D () K ø 1,5 ➇ T ø 10 ➅ K ø 1,5 ➇ SR 0,4 ➆ K ø 1,5 ➉ Kø1,5/SR 0,4 ➈ Packaging *1732/01 *1732/01 *1732/01 *1732/01 *1732/01 *1732/01 Serie OD 10 Oditest specification OD1020 OD1020R OD2050 OD2050R OD20100 OD20150 OD2050F80 OD2050F130 OD20100F80 Measuring range () 0-20 0-20 0-50 0-50 50-100 100-150 0-50 0-50 50-100 Range () 20,0 20,0 50,0 50,0 50,0 50,0 50,0 50,0 50,0 Graduation () 0,010 0,010 0,050 0,050 0,050 0,050 0,050 0,050 0,050 Repetability () 0,015 0,015 0,020 0,020 0,030 0,030 0,030 0,030 0,030 Measuring faces «L» () 80,0 80,0 170,0 170,0 170,0 170,0 170,0 170,0 170,0 Measuring contact () 1,5 ➃ 1,5 ➅ 2,0 ➃ 2,0 ➇ 2,0 ➃ 2,0 ➃ 2,0 ➃ 2,0 ➃ 2,0 ➃ Measuring contact length «Hb» () 22,0 22,0 32,0 32,0 32,0 32,0 32,0 32,0 32,0 Measuring contact length «Hf» () 22,0-32,0-32,0 32,0 82,0 132,0 82,0 Carbide bezel OD1020S➂ OD1020RS➄ OD2050S➂ OD2050RS➆ - - - - - Disc measuring face ø 10 ➁ OD1020T10 - OD2050T10 - - - - - - Disc measuring face ø 50 ➀ - - OD2050T - OD20100T OD20150T OD2050F80T OD2050F130T OD20100F80T E 38

Dial caliper gauge for inside measurement E Serie ID 20 Dial caliper gauge for inside measurement ID2015 ID2040 ID2040K1 ID2070 ID2070K1 ID20100 ID2010K1 ID20130 ID20130K1 ID20150 ID20180 Measuring range () 15-65 40-90 40-90 70-120 70-120 100-150 100-150 130-180 130-180 150-200 180-230 Range () 50,0 50,0 50,0 50,0 50,0 50,0 50,0 50,0 50,0 50,0 50,0 Graduation () 0,005 0,05 0,05 0,05 0,05 0,05 0,05 0,05 0,05 0,05 0,05 Repetability () 0,010 0,010 0,010 0,010 0,010 0,015 0,015 0,015 0,015 0,015 0,020 Measuring depth «L» () 170,0 175,0 175,0 175,0 175,0 175,0 175,0 175,0 175,0 175,0 175,0 Groove depth «A» () 4,5 8,0 3,0 8,0 3,0 8,0 3,0 8,0 3,0 8,0 8,0 Groove width «B» () 2,5 3,3 1,6 3,3 1,6 3,3 1,6 3,3 1,6 3,3 3,3 Measuring contact () 1,5 ➀ 2,0 ➂ 1,0 ➂ 2,0 ➂ 1,0 ➂ 2,0 ➂ 1,0 ➂ 2,0 ➂ 1,0 ➂ 2,0 ➂ 2,0 ➂ Measuring contact length «Hb» () 5,3 10,5 10,5 10,5 10,5 10,5 10,5 10,5 10,5 40,5 40,5 Measuring contact length «Hf» () 5,3 10,5 10,5 40,5 40,5 10,5 10,5 40,5 40,5 10,5 40,5 Measuring contact width «S» () 1,8 2,5 2,5 2,5/5,0 2,5/5,0 2,5 2,5 2,5/5,0 2,5/5,0 5,0/2,5 5,0/5,0 ID10M60 *) ID10M120 *) ID20M180 *) ID20M300 *) ID20M420 *) Measuring range () 60-130 120-190 180-310 300-430 420-550 Range () 20,0 20,0 50,0 50,0 50,0 Graduation () 0,010 0,05 0,05 0,05 0,05 Repetability () 0,010 0,015 0,020 0,025 0,030 Measuring depth «L» () 80,0 80,0 170,0 170,0 170,0 Number of measuring contact 6 6 3 3 3 Serie ID 10 M E 39

Dial caliper gauge for outside measurement Measuring faces K=Round S=Knife T=Disc Serie OD 20 Dial caliper gauge for outside measurement OD2050B OD2050BR OD2050BF80 OD2050BF130 Measuring range () 0-50 0-50 0-50 0-50 Range () 50,0 50,0 50,0 50,0 graduation () 0,050 0,050 0,050 0,050 Repetability () 0,020 0,020 0,030 0,030 Measuring depth «L» () 170,0 170,0 170,0 170,0 Measuring contact () 2,0 ➃ 2,0 ➇ 2,0 ➃ 2,0 ➃ Measuring contact length «Hb» () 82,0 82,0 82,0 82,0 Measuring contact length «Hf» () 32,0-82,0 132,0 Disc measuring face ø 50 ➀ OD2050BT - OD2050BF80T OD2050BF130T E 40

Dial caliper gauge for outside measurement E Dial caliper gauge for outside measurement K=Radius S=Knife T=Disc F=Disc ; Knife N=Needle Measuring range () Range () Graduation () Repetability (fw) () Error limit (fe) ) Measuring depth «L» () Measuring faces () Poco 2K 0-10 10 0,10 0,05 0,1 36 Kø2,0 ➇ KE Poco 2N 0-10 10 0,10 0,05 0,1 36 Nø0,75 ➉ KE Poco 2T 0-10 10 0,10 0,05 0,1 36 Tø10 12 KE Poco 2F 0-10 10 0,10 0,05 0,1 36 SR 0.5/Fø3,5 11 KE Packaging Dial caliper gauge for inside measurement 2 points measurement 3 points measurement EID 1510 EID 1530 EID 1550 EID 1570 EID 0715 P3 EID 1520 P3 EID 1530 P3 EID 1540 P3 Measuring range 10-35 30-55 50-75 70-95 15-25 20-40 30-50 40-60 Graduation 0,01 0,01 0,01 0,01 0,0025 0,005 0,005 0,005 Repetability 0,03 0,02 0,03 0,04 0,003 0,005 0,005 0,005 Precision ± 0,03 ± 0,02 ± 0,02 ± 0,04 ± 0,006 ± 0,01 ± 0,01 ± 0,01 Measuring ability 2-3 N 2-3 N 2-3 N 2-3 N 2-3 N 2-3 N 2-3 N 2-3 N Weight 0,43 kg 0,56 kg 0,47 kg 0,48 kg 0,45 kg 0,55 kg 0,54 kg 0,55 kg Depth L 56 110 110 100 40 110 110 110 Depth A 1/4,5 3,5/8,5 3,5/8,5 3,5/8,5 3 3,5 6 6 Width B 1,1/1,8 2,5/4,5 2,5/4,5 2,5/4,5 2,5 2,5 2,5 2,5 E 41

Dial caliper gauge for inside and outside measurements EID 1010 Intertronic / Oditronic Specificaties : Battery (lithium 3V) Output RS 232 Conversion /inch Display LCD (7 ) Round measuring faces ø 0,8 Round measuring faces ø 1 Round measuring faces ø 1,5 Round measuring faces ø 1 Round measuring faces ø 2 EOD 1025 EID0505 EID1010 EID1030 EID 1050 EID1070 EID2015 EID2040 EID2070 Measuring range Awb () 5-17,5 10-35 30-55 50-75 70-95 15-65 40-90 70-120 Range Meb () 12,5 25 25 25 25 50 50 50 Graduation Zw () 0,005 0,01 0,01 0,01 0,01 0,02 0,02 0,02 Error limit f M () ± 0,02 ± 0,03 ± 0,03 ± 0,03 ± 0,03 ± 0,04 ± 0,04 ± 0,04 Repeatability F w () 0,015 0,03 0,03 0,03 0,03 0,04 0,04 0,04 Measuring depth L () 20 80 80 80 80 175 175 175 Groove depth A () 1,5 4,5 6 8 8 4,5 8 8 Measuring face D () Kø0,8 ➁ Kø1 ➁ Kø1 ➁ Kø1 ➂ Kø1 ➂ Kø1,5 ➁ Kø2 ➃ Kø2 ➃ Measuring face length : moving Hb () 2,5 5 7 10 10 5,3 10,5 10,5 Measuring face length : fast Hf () 2,5 5 7 20 20 5,3 10,5 40,5 Measuring face depth S () 1,2 1,2 1,9 2,5/4 2,5/4 1,8 2,5 2,5/5 Packaging *1732/43 *1732/43 *1732/43 *1732/43 *1732/43 *1732/43 *1732/43 *1732/43 EOD0512R EOD1025 EOD1025R EOD1025T10 EOD2050 EOD2050R EOD2050T EOD20100 Measuring range Awb () 0,2-12,5 0,3-25 0,3-25 0,3-25 0,5-50 0,5-50 0,5-50 50-100 Range Meb () 12,3 24,7 24,7 24,7 49,5 49,5 49,5 50 Graduation Zw () 0,005 0,01 0,01 0,01 0,02 0,02 0,02 0,02 Error limit f M () ± 0,015 ± 0,02 ± 0,02 ± 0,03 ± 0,04 ± 0,04 ± 0,06 ± 0,04 Repeatability F w () 0,02 0,02 0,02 0,02 0,04 0,04 0,06 0,04 Measuring depth L () 25 80 80 80 170 170 170 170 Measuring face D () Kø1,5 ➇ Kø1,5 ➅ Kø1,5 12 Kø10 ➉ Kø2 ➅ Kø2 14 Kø50 ➆ Kø2 ➅ Measuring face length : moving Hb () 22 22 22 22 32 32 35 32 Measuring face length : fast Hf () 1 22 2,3 15 32 1 22 32 Knife () EOD0512RS➈ EOD1025S➄ EOD1025RS 11 EOD2050S➄ EOD2050RS 13 Packaging () *1732/43 *1732/43 *1732/43 *1732/43 *1732/43 *1732/43 **HK *1732/32 E 42

Surfaces gauges E 28201 Round base Length : 300-400 - 500 28202 Prismatic base Length : 300-400 - 500 28201 28202 28203 Height gauge Length : 300-500 - 750 27301 Height gauge Length : 300-600 - 1000 Satin chrome finish - Hard metal needle 28203 27301 27302 Digital height gauge Reading 0,01 / 0,0005 inch Stainless steel Hard metal needle Length : 300-500 - 1000 Digital height gauge and scriber Robust standard model in pillar form With and without signal probe connector. With and without data output Zero setting at turn of a knob to any position PRESET key (preselected) : presetting of initial value of measuring range or any value for comparative measurement. Measuring range Incremental value Error limits Without signal probe connector and data output 192-613 0-300 0,01 0,02 192-614 0-600 0,01 0,05 With signal probe connector and data output 192-663 0-300 0,01 0,02 192-664 0-600 0,01 0,04 192-613 192-613/614 Optional accessories Designation 905338 Signal cable (1m) 905409 Signal cable (2m) 192-007 Signal probe ABSOLUTE DIGIMATIC HDS height gauge Standard measuring device for simple workshop use. Built-in absolute scale Easy-moving, precise height adjustment using a hand wheel Large, high-contrast six-figure LCD display With data output 570-302 Optional accessories Designation 905338 Signal cable (1m) 905409 Signal cable (2m) Measuring range Incremental value Error limits 570-302 0-300 0,01 0,03 570-304 0-600 0,01 0,05 570-302 / 570-304 E 43

Steel marking gauge and steel beam 273011 Steel marking gauge with round rod Reading 1/10 Satin chrome finish Range 300 500 273012 Steel marking gauge, flat pattern Stainless steel - satin chrome finish Range 200 250 300 273013 Steel marking gauge Reading 1/10 Length 300 400 500 25009 Steel beam troels - round rod Reading 1/10 Length 500 1000 1500 2000 3000 25012 Steel beam troels - flat rod Length 500 1000 1500 2000 3000 273014 Marking vernier caliper Reading 1/20 - Carbide point Range 200 400 273015 Marking vernier caliper DIN 862 Reading 1/20 Satin chrome finish Range 250 300 400 273016 Thread feeler gauge Measuring range 30 Reading 1/10 E 44

V-blocks E 26601 V-blocks Dimensions L x w x H Accuracy 0 (0,008 ) Accuracy 3 (0,064 ) 75 x 40 x 40 Yes Yes 100 x 40 x 30 Yes Yes 150 x 50 x 40 Yes Yes 200 x 70 x 50 Yes Yes 250 x 85 x 60 Yes Yes 300 x 100 x 70 Yes Yes 26504 V-blocks DIN 876/1 Dimensions L x w x H For shaft ø Degree 0 Degree 1 60 x 60 x 50 5-40 - Yes 75 x 75 x 50 5-50 - Yes 120 x 100 x 60 8-80 Yes Yes 150 x 130 x 75 8-100 Yes Yes 200 x 170 x 90 10-170 Yes Yes Numbered per pair 26506 V-blocks with clamp DIN 876/1 Dimensions L x w x H For shaft 45 x 40 x 36 5-20 70 x 45 x 40 5-25 70 x 63 x 45 5-32 125 x 90 x 70 5-45 Numbered per pair 26510 Precision tool markers vices Jaw width Jaw opening Total length Jaw height 72 100 210 35 125 160 300 50 Error limits 0,005 / 100 26511 Precision sinus vice Jaw width Jaw opening Total length Jaw height 76 100 190 35 100 127 245 45 E 45

Steel rules 27502 Flexible steel rules Length Measurements Type Graduation 100 13 x 0,5 Flexible or /inches on 2 faces 150 13 x 0,5 200 13 x 0,5 250 13 x 0,5 300 13 x 0,5 500 20 x 0,5 1000 25 x 0,5 300 30 x 0,8 500 30 x 0,8 1000 30 x 1,0 1500 30 x 1,0 2000 30 x 1,0 3000 30 x 1,0 5000 30 x 1,0 500 30 x 2,0 Semi-Half flexible 1000 30 x 2,0 1000 40 x 2,0 1500 40 x 2,0 2000 40 x 2,0 27703 Hardened straight edges DIN 874 with insulated handle-stainless steel Length : 75-100 - 125-150 - 200-250 - 300-400 - 500-600 - 800-1000 27611 Edge of anodic oxidated aluminium, bevelled edge, graduation Length 300 600 1000 Steel rules, with bevelled edge, with, without graduation, mild steel 27506 with graduation, precision 5 microns DIN 866/II 27507 without graduation, polished 27508 with graduation, polished Length Measurements 27506 27507 27508 300 40 x 5-400 40 x 5-500 40 x 5 1000 40 x 5 1500 40 x 5 2000 40 x 5 - - 2000 40 x 6-3000 40 x 5 - - 3000 40 x 6 - E 46

Steel rules E Steel rules DIN 866/1 Each end 5 unmarked Length 500 1000 1500 2000 3000 4000 5000 Section 30 x 6 40 x 8 40 x 8 50 x 10 50 x 10 60 x 12 70 x 14 27603 Mild steel 27604 Stainless steel on request on request 27603-27605 Steel rules DIN 866/2 Length 500 1000 1500 2000 3000 4000 5000 Section 25 x 5 30 x 6 30 x 6 40 x 8 40 x 8 50 x 10 60 x 12 27605 Mild steel 27606 Stainless steel Precision steel edge DIN 874/0 Length 500 1000 1500 2000 3000 Section 50 x 10 60 x 12 70 x 14 80 x 15 120 x 18 27801 Mild steel 27802 Stainless steel Precision steel edge DIN 874/1 Length 500 1000 1500 2000 3000 Section 40 x 8 50 x 10 60 x 12 70 x 14 100 x 16 27808 Mild steel 27809 Stainless steel DIN 874 Precision steel edge DIN 874/2 Length 500 1000 1500 2000 3000 Section 30 x 6 40 x 8 50 x 10 60 x 12 80 x 15 27803 Mild steel 27804 Stainless steel 25115 Pimeter DIN 7168M Reading in / 0,1 For circumference For diameter 60-950 940-2200 2190-3460 3450-4720 4710-5980 5960-7230 20-300 300-700 700-1100 1100-1500 1500-1900 1900-2300 E 47

Measuring tapes 27741003 Pocket measuring tapes 3 m Width 16 - Steel case - Spring return - With clip for fixing to belt 27741005 Pocket measuring tapes 5 m Width 19 - Steel case - Spring return - With clip for fixing to belt 27741008 27741008 Pocket measuring tapes 8 m Width 25 - Steel case - Spring return - With clip for fixing to belt 27741010 Pocket measuring tapes 10 m Width 25 - Steel case - Spring return - With clip for fixing to belt 27742003 27742003 Pocket measuring tapes 3 m Width 13 - Nylon case - Spring return - Direct reading 27743003 27743002 Pocket measuring tapes 2 m Width 13 - Nylon case 27743003 Pocket measuring tapes 3 m Width 13 - Nylon case 27744003 Pocket measuring tapes 3 m Width 13 - Nylon case - Spring return 27744003 27745003 Pocket measuring tapes 3 m Width 19 - Steel case - Spring return - With clip for fixing to belt 27745005 27745005 Pocket measuring tapes 5 m Width 19 - Steel case - Spring return - With clip for fixing to belt 27760 Steel flat tapes self-adhesive Length Width 2 m 13 3 m 13 10 m 13 27761 Tailoring tapes Length : 1m 500 Width : 20 E 48

Measuring tapes Tolerance accuracy EEC standard E Folding rules 27705 Folding rules 2 m of wood 27733 Folding rules of glass fibre 27709 Folding rules 2 m 27711 Folding rules 2 m - stainless steel 27726001 152 Pocket measuring tapes 2 m Plastic case - Width 13-2 graduations in 27726003 153 Pocket measuring tapes 3 m Plastic case - Width 13-2 graduations in 27726005 707 Pocket measuring tapes 2 m Plastic case - Locking device, spring return - Width 13-2 graduations in 27726007 708 Pocket measuring tapes 3 m Plastic case - Locking device, spring return - Width 13-2 graduations in 27726010 709 Pocket measuring tapes 5 m Plastic case - Locking device, spring return - Width 13-2 graduations in 27726009 Pocket measuring tapes 2 m Width 16 - Stainless steel case - Spring return 27726003 27735001 Pocket measuring tapes 2 m Width 19 - Steel case- Spring return - With clip for fixing to belt 27736001 Pocket measuring tapes 3 m Width 19 - Steel case- Spring return - With clip for fixing to belt 27726007 27737001 Pocket measuring tapes 5 m Width 19 - Steel case- Spring return - With clip for fixing to belt 27737002 Pocket measuring tapes 5 m Width 25 - Steel case- Spring return - With clip for fixing to belt 27740003 Pocket measuring tapes 8 m Width 25 - Steel case- Spring return - With clip for fixing to belt 27740002 Pocket measuring tapes 10 m Width 25 - Steel case- Spring return - With clip for fixing to belt 27737002 E 49

Laserdistance meter LEICA DISTO Features A2 A3 A5 A6 A8 Measuring accuracy Measuring range Aera volume, measurement Room calculation Indirect measurement with Pytagoras ± 1,5 ± 1,5 ± 1,5 ± 1,5 ± 1,5 0,05-60 m 0,05-100 m 0,05-200 m 0,05-200 m 0,05-200 m V V V V V - - V V V - - V V V Tilt sensor - - V V V Min/max, distance tracking Store constant value Recall last valves BLUETOOTH data transfer LCD display illumination V V V V V - - 1 1 1-19 20 20 30 - - - V V V V V V V A2 A3 A5 A6 Batteries 9,6 V AAA 2 x 1,5V AA 2 x 1,5 V AA 2 x 1,5 V AA 2 x 1,5 V Dimensions Weight with batteries 124 x 45 x 31 135 x 45 x 31 148 x 64 x 36 148 x 64 x 36 148 x 64 x 36 155 g 145 g 241 g 270 g 280 g A8 Accessories 667169 Softbag 723744 Stick-on target plate 723385 Target plate A4 (For longer distance) 723777 Laser glasses 739200 Clips, hangs comfortably from the belt or waist band E 50

E 27724 Telescopmeter Length 5 m 27765 Light road measuring wheels Ø wheel 320 - Digital Reading m/dm Capacity 10.000 m MEASURING TAPES Woven fiber glass tapes 28102 Special building work 10 m 15 m 20 m 25 m 30 m 50 m Graduation 2 sides cm - Width 15 28102 28102 10 m 15 m 20 m 25 m 30 m 50 m Graduation 2 sides - Width 15 Class II (ECC approuval) 28102 class II 28102 40 m 60 m Graduation 2 sides Width 15 High speed return Class II (ECC approuval) 28102 STEEL TAPE 28104 10 m 15 m 20 m 25 m 30 m 50 m Graduation 1 side Class II (ECC approuval) Width 13 m 28104 28108 10 m 15 m 20 m 25 m 30 m 50 m Graduation 1 side - Width 13 With handle Class II (ECC approuval) 28108 E 51

Measuring tapes Stainless steel tape 28106 10 m 15 m 20 m 25 m 30 m 50 m Graduation 1 side - Width 13 Class II (EEC approuval) 28110 10 m 15 m 20 m 25 m 30 m 50 m Graduation 1 side - With handle Class II (EEC approuval) White enamelled steel tape 28111 10 m 20 m 30 m 50 m Graduation Width 12 Class II (EEC approuval) 28114 20 m 30 m 50 m Graduation Width 13 With handle Class II (EEC approuval) 280201 Stainless steel dip weight Engraved numbers For water, solvents, slightly acid mix, oil 10 m 20 m 30 m Width 13 Graduation 1 side With plumb bob E 52

Steel squares Steel squares DIN 875/1 25305 25306 Dimensions Flat With back 75 x 50 100 x 70 150 x 100 200 x 130 250 x 165 300 x 200 400 x 265 500 x 330 Squares DIN 875/2 25401 25402 Dimensions Flat With back 75 x 50 100 x 70 150 x 100 200 x 130 250 x 160 300 x 175 400 x 200 500 x 250 600 x 300 750 x 375 1000 x 500 Squares zinc plated 25410 25411 Dimensions Flat With back 100 x 70 150 x 100 200 x 130 250 x 160 300 x 180 400 x 230 500 x 280 600 x 330 700 x 375 1000 x 500 1250 x 625 150 x 750 2000 x 1000 Flange steel squares Dimensions 25501 300 x 300 400 x 400 500 x 500 600 x 600 800 x 800 E 53

Steel squares Control squares DIN 875/0 Stainless steel 25303 25304 Dimensions Flat With back 75 x 50 100 x 70 150 x 100 200 x 130 250 x 165 300 x 200 Control squares DIN 875/1 Stainless steel 25307 25308 Dimensions Flat With back 75 x 50 100 x 70 150 x 100 200 x 130 250 x 165 300 x 200 400 x 265 500 x 330 Control squares DIN 875/2 Stainless steel 25309 25310 Dimensions Flat With back 75 x 50 100 x 70 150 x 100 200 x 130 250 x 165 300 x 175 400 x 200 500 x 250 Control squares, stainless steel hardened DIN 875/0 25205 25207 Dimensions Flat With back 50 x 40 75 x 50 100 x 70 150 x 100 200 x 130 300 x 200 400 x 265 500 x 330 25212 Control squares, stainless steel, hardened DIN 875/0 with heavy base Dimensions Flat With back 100 x 70 150 x 100 E 54

Steel squares Control squares, stainless steel, hardened with bevelled edge - DIN 875/00 25206 25208 Dimensions Flat With back 50 x 40 75 x 50 100 x 70 150 x 100 200 x 130 300 x 200 400 x 265 500 x 330 25505 Steel squares with heavy beam DIN 875/2 Dimensions 100 x 70 125 x 75 150 x 100 200 x 130 250 x 160 300 x 200 25801 Adjustable knife edge square, stainless steel DIN 875/0 Length : 60 Knife edge : 4 x 4 x 60 Body : 40 x 23 x 10 25802 Control squares with inside bevelled edges, stainless steel hardened DIN 875/0 Dimensions 25 x 20 40 x 28 25803 Multidegrees squares (4 angles) Angles : 90-45 - 30-120 Made of steel With back Dimensions 100 150 200 300 E 55

Steel squares 25604 Steel squares 120 Dimensions Flat 50 x 50 75 x 75 100 x 100 150 x 150 200 x 200 Steel squares 135 25606 25608 Dimensions Flat With back 50 x 50-75 x 75-100 x 70 150 x 100 200 x 130 250 x 165-300 x 175-25606 25608 Steel squares à 45 25704 25706 Dimensions Flat With back 100 x 80 125 x 80 150 x 100 200 x 130 250 x 160 300 x 200 25407 Centre square Dimensions 150 x 130 200 x 150 250 x 160 300 x 180 400 x 250 500 x 330 25702 Joiners adjustable bevels Dimensions 150 200 250 300 400 500 25311 Digital analogical square Length 350 Range 0-185 E 56

Square E 25502 Combinations squares With spirit level and scriber Length 300 27914 Combination square Usable as height, depth gauge, bevel protector, centre square Length 600 25312 Squares set, stainless steel Set of : - 1 Knife edge (bevelled edge) 75 x 50 DIN 875/00-1 Knife edge (bevelled edge) 40 x 28 DIN 874/00-1 Knife edge (bevelled edge) 25 x 20 DIN 874/00-1 knife straight edge 100 DIN 874/00-1 scriber 45 25313 Precision measuring tools set Set of : - 1 Knife edge 100 x 70 DIN 875/00-1 knife straight edge 100-1 DIGITAL micrometer 0-25 - 1 steel rule 300-1 caliper 150 DIN 862 DIGITAL - 1 divider 125-1 carbide scriber - 1 depth basis 75-1 centre punch 100 25314 Precision measuring tools set - 1 Knife edge 100 x 70 DIN 875/00-1 knife straight edge 100-1 micrometer 0-25 - 1 steel rule 300-1 caliper 150 DIN 862-1 divider 125-1 carbide scriber - 1 depth basis 75-1 centre punch 100 E 57

Dividers Dividers with rivet joint DIN 6486 Length 150 200 250 300 400 500 600 24903 Divider 24903 24906 24904 Wing divider 24905 Wing divider with pencil houder DIN 6484 - - - - 24906 Inside divider DIN 6482 24907 Outside divider DIN 6484 24904 24907 24909 Combination dividers - - - 24909 24905 Dividers with adjustable screw hinge Length 150 200 250 300 400 500 600 800 1000 24901 24901 Divider DIN 6486 - - - 24902 Wing divider DIN 6486 - - - 24902 24806 24805 Inside divider DIN 6482 24806 Outside divider DIN 6484 24805 Spring divider, quick nut DIN 6487 Length 100 125 150 175 200 250 300 400 500 600 25001 Divider 25001 25002 25002 Inside divider 25003 Outside divider 25003 25007 Internal and external calipers with precision scale, reading 1 Graduation 120 160 200 250 300 25007 Length 190 250 310 380 460 25107 Precision spring gauge, reading 1/10 Capacity 0-10 0-15 0-20 25107 E 58

Scribers E SCRIBERS Length 190 Length 250 25102 Straight scriber 25103 With straight and bent blades 25104 Straight blade with knurled handle - 25105 Straight and bent blade, knurled handle 25105915 Straight and bent blade with plastic handle - 25106 With carbide tip, plastic body - 25114 Pencil, metal body, carbide tip - 25121 Pencil, carbide tip, steel body - PROTACTORS 27902 Protactors Stainless steel - ø ground round plate 90 Length 240-0-180 27915 Width adjustable blade 10-170 ø protactor 100 150 200 250 300 Length of blade 150 300 400 500 600 27906 Universal bevel protactor Stainless steel - Satin chrome finish reading 1/12 = 5 minutes - With magnifier and square Length of blade 150 200 300 500 27917 DIGITAL universal Protactor Stainless steel - With data output RS232 Measuring range 1 x 360, 2 x 180, 4 x 90 (preset) Length of blade 150 200 300 500 E 59

Small gauges SCREW PITCH GAUGES 28001 Withworth thread - 55 (4-62) - 28 blades 28002 Metric thread - 60 (0,25-6) - 24 blades 28001-02-03 28003 Metric SI - Withworth draad- 55-60 - 52 blades 28003004 Pipe thread - 55 (8-28) - 6 blades 28004001 Angled and squared threads 28005 Acme thread 2-12 DIN 103 28004 28005 28006 Angled thread cutter gauge - 51-60 28007 Angled thread cutter gauge - 55 BSW 28006-07 28008 Twist drill grinding gauge, 118 top hake - to Ø 50 28008 28008002 Universal twist drill grinding gauge 28008002 28042 Universal weld seam gauges 28042 28043 Universal weld seam gauges For measuring right angled welds 3-12 28043 28020 Radius gauge 1-7 28021 Radius gauge 7,5-15 28022 Radius gauge 15,5-25 28030 Wire and twist drills gauges - 100 Holes (0,1-10 ) 28031 Wire and twist drills gauges - 21 Holes (10-20 ) 28020-21- 22 28030-31 28033 Taper gauges 1-15, 15-30, 30-45, 45-60 28034 Jet gauges with steel pins Ø 0,45-1,5 (20 pins) 28035 Jet gauges with steel pins Ø 1,5-3 (16 pins) 28033 28034-35 28037 DIN thread rule 28037 28044 Thread indicator filetor 28044 28045 Tolerance indicator tolerator 28045 E 60

Feeler gauges Feeler gauges in case Ref. Blades Set combination 28009001 20 0,05-1,00 28009002 20 0,10-2,00 28009003 22 0,03-1,00 28010001 18 0,04-1,00 28011001 13 0,05-1,00 0,05-0,10-0,15-0,20-0,25-0,30-0,35-0,40-0,45-0,50-0,55-0,60-0,65-0,70-0,75-0,80-0,85-0,90-0,95-1,00 0,10-0,20-0,30-0,40-0,50-0,60-0,70-0,80-0,90-1,00-1,10-1,20-1,30-1,40-1,50-1,60-1,70-1,80-1,90-2,00 0,03-0,04-0,05-0,10-0,15-0,20-0,25-0,30-0,35-0,40-0,45-0,50-0,55-0,60-0,65-0,70-0,75-0,80-0,85-0,90-0,95-1,00 0,04-0,05-0,06-0,07-0,08-0,09-0,10-0,15-0,20-0,25-0,30-0,40-0,50-0,60-0,70-0,80-0,90-1,00 0,05-0,10-0,15-0,20-0,25-0,30-0,40-0,50-0,60-0,70-0,80-0,90-1,00 28013001 8 0,05-0,50 0,05-0,10-0,15-0,20-0,25-0,30-0,40-0,50 Feeler gauge on a ring (Length 150 -> 1000 ) Blades Capacity 150 200 28014 8 l 0,05-0,5 28015 13 l 0,05-1 28016 20 l 0,05-1 28017 20 l 0,10-2 300 400 500 600 800 1000 280181 Thickness gauge band Thickness 13 x 5 m Steel 13 x 10 m Steel 13 x 5 m Stainless steel Thickness 25 x 5 m Steel 50 x 5 m Steel 100 x 5 m Stainless steel 0,005 0,01-0,01 0,02 0,02 0,03-0,03 0,04-0,04 0,05 0,05 0,06-0,06-0,07-0,07-0,08-0,08-0,09-0,09-0,1 0,1 0,12 - - 0,12-0,15 0,15 0,18 - - 0,18-0,2 0,2 0,25 - - 0,25 0,3 0,3 0,35-0,35-0,4 0,4 0,45 - - 0,45-0,5 0,5 0,6 0,6-0,7 0,7-0,8 0,8-0,9 0,9-1 1 - E 61

Precisions blades Precisions blades in box - Roll of 2500 Ref. = Thickness Shim/strip 150 x 2500 allied steel Shim/strip 150 x 2500 stainless steel Shim/strip 150 x 2500 Brass 0,025 0,05 0,075 0,1 0,15 0,2 0,25 0,3 0,4 0,5 Precision blades 50 / 100 / 150 width Ref. = Thickness 50 x 300 10 pc. Steel C 100 x 500 5 pc. Stainless steel 150 x 500 5 pc. Stainless steel 150 x 500 5 pc. Brass 0,02 - - - - 0,025 - - 0,05-0,075 - - 0,1 0,15 0,2 0,25 - - 0,3 0,4 0,5 0,6 - - 0,7 - - 0,8 - - 0,9 - - 1 - - E 62

Gauges 23601 Cylindrical limit plug gauge, go, not go DIN 7162 - DIN 7164 Outside ø Outside ø Outside ø 0,2 15 45 0,3 16 46 0,5 17 47 0,8 18 48 1 19 50 1,2 20 52 1,5 21 55 1,8 22 58 2 23 60 2,2 24 62 2,5 25 65 2,8 26 68 3 27 70 3,5 28 72 4 30 75 4,5 32 78 5 33 80 6 34 82 7 35 85 8 36 88 9 37 90 10 38 92 11 40 95 12 42 98 13 44 100 14 23601 23602 Flat plug gauges (go - not go) Outside ø Outside ø Outside ø 8-9-10-11-12 30-32-33-34-35 58-60-62 13-14-15 36-37-38-40 65-68-70 16-17-18-19 42-44-45 72-75-78-80 20-21-22-23-24 46-47-48 82-85-88 25-26-27-28 50-52-55 90-92-95-98-100 23602 Up 100, 1 gauge go, 1 gauge not go Outside ø Outside ø Outside ø 100-110 200-220 350-375 110-120 220-240 375-400 120-135 240-260 400-425 135-150 260-280 425-450 150-165 280-300 450-475 165-180 300-320 475-500 180-200 320-350 These gauges are which can be delivered under delay Gauges in hard metal (Widia) on request 23603 E 63

Gauges 23701 Limit snap gauges (Go - Not go) Dimensions Dimensions Dimensions 2 13-14 44-45-46 2,5 15-16-17-18 47-48 2,8 19-20-21-22 50-52-55 3-3,5 23-24 58-60-62 4-4,5 25-26 65-68-70 5-6 27-28-30 72-75 7 32-33 78-80-82 8 34-35-36 85 9-10 37-38 88-90-92 11-12 40-42 95-98-100 23701 23702 Limit snap gauges (Go - Not go) Dimensions Dimensions Dimensions 2 15-16-17-18 44-45-46 2,5 19-20-21-22 47-48 2,8 23-24-25-26 50-52-55 3-3,5 27-28-30 58-60-62 4-4,5 32-33 65-68-70 5-6 34-35 72-75 7 36 78-80-82 8-9-10 37-38 85-88-90-92 11-12 40-42 95-98-100 13-14 23702 23703 Limit snap gauges (Go - Not go) Dimensions Dimensions Dimensions 100-110 205-220 340-365 110-125 220-240 365-390 125-140 240-265 390-415 140-155 265-290 415-445 155-170 290-315 445-475 170-185 315-340 475-500 185-205 23703 E 64

Gauges Morse taper gauges WITHOUT TANG - DIN 229-324 Morse konus Male gauge DIN 229 Female gauge short DIN 229 Female gauge long DIN 324 23801 23802 23803 0 1 2 3 4 5 6 WITH TANG - DIN 230 Morse konus Male gauge DIN 230 Female gauge sided tang DIN 230A Female sided tang DIN 230B 23804 23805 23806 0 1 2 3 4 5 6 Metric taper gauge WITHOUT TANG - DIN 234-325 WITH TANG - DIN 235 Metric taper Male gauge DIN 234 Female short DIN 234 Female long DIN 235 Metric taper Male with tang Female 1 sided tang DIN 235 A Female two sided tang DIN 235B 23807 23808 23809 23810 23811 23812 4 9 6 12 9 18 12 24 18 32 24 40 32 50 40 60 50 70 60 80 70 90 80 100 90 110 100 120 110 130 120 140 130 150 140 150 E 65

Go - Not go thread plug gauge METRIC Limit thread plug gauge Limit thread plug gauge with rolles Thread ring gauge go-not go Thread plug gauge go Thread plug gauge not go Code 24001 24002 24004 24005 24006 ø M 1 M 1,2 M 1,4 M 1,6 M 1,8 M 2 M 2,2 M 2,5 M 3 M 3,5 M 4 M 5 M 6 M 7 M 8 M 9 M 10 M 11 M 12 M 14 M 16 M 18 M 20 M 22 M 24 M 27 M 30 M 33 M 36 M 39 M 42 M 45 M 48 M 52 M 56 M 60 M 64 M 68 E 66

Thread plug gauge E WW DRAAD Limit thread plug gauge Limit thread plug gauge with rolles Thread ring gauge go-not go Thread plug gauge go Thread plug gauge not go Code 24101 24102 24104 24105 24106 ø 1/16 3/32 1/8 5/32 3/16 7/32 1/4 5/16 3/8 7/16 1/2 9/16 5/8 11/16 3/4 13/16 7/8 15/16 1 1 1/8 1 1/4 1 3/8 1 1/2 1 5/8 1 3/4 1 7/8 2 2 1/8 2 1/4 2 3/8 2 1/2 2 5/8 2 3/4 2 7/8 3 3 1/8 3 1/4 3 3/8 3 1/2 E 67

Thread plug gauge BSP THREAD Limit thread plug gauge Limit thread plug gauge with rolles Thread ring gauge go-not go Thread plug gauge go Thread plug gauge not go Code 24201 24202 24204 24205 24206 ø R 1/8 R 1/4 R 3/8 R 1/2 R 5/8 R 3/4 R 7/8 R1 R1 1/8 R1 1/4 R1 3/8 R1 1/2 R1 5/8 R1 3/4 R2 R2 1/4 R2 3/8 R2 1/2 R2 3/4 R3 R3 1/4 R3 1/2 NF THREAD 24207 24208 24210 24211 24212 N 0-80 NF N 1-72 NF N 2-64 NF N 3-56 NF N 4-48 NF N 5-44 NF N 6-40 NF N 8-36 NF N 10-32 NF N 12-28 NF 1/4-28 NF 5/16-24 NF 3/8-24 NF 7/16-20 NF 1/2-20 NF 9/16-18 NF 5/8-18 NF 3/4-16 NF 7/8-14 NF 1-12 NF 1 1/8-12 NF 1 1/4-12 NF 1 3/8-12 NF 1 1/2-12 NF E 68

Thread plug gauge E NC THREAD Limit thread plug gauge Limit thread plug gauge with rolles Thread ring gauge go-not go Thread plug gauge go Thread plug gauge not go Code 24301 24302 24304 24305 24306 ø N 1-64 NC N 2-56 NC N 3-48 NC N 4-40 NC N 5-40 NC N 6-32 NC N 8-32 NC N 10-24 NC N 12-24 NC 1/4-20 NC 5/16-18 NC 3/8-16 NC 7/16-14 NC 1/2-13 NC 9/16-12 NC 5/8-11 NC 3/4-10 NC 7/8-9 NC 1-8 NC 1 1/8-7 NC 1 1/4-7 NC 1 3/8-6 NC 1 1/2-6 NC 1 3/4-5 NC 2-4 1/2 NC 2 1/4-4 1/2 NC 2 1/2-4 NC 2 3/4-4 NC 3-4 NC 3 1/4-4 NC 3 1/2-4 NC 3 3/4-4 NC 4-4 NC E 69

Gauge block sets Gauge block sets made of steel Made of high quality alloyed and stress relieved special steel of high stability and with good adhesive power. Carefully heat treated and lapped. Slightly broken edges. Each gauge block is provided with an identification number. The gauge block hardness is 800 HV (64 HRC); therefore they are extremely wear resistant. The gauge block sets are stored in a wooden box iediately after calibration. The wooden box is included in the price. Specifications Accuracy : DIN EN ISO 3650 Tolerance grade : K For laboratories Tolerance grade : 0 As reference gauge for controlling workshop gauge blocks. For adjusting high precision measuring instruments. Tolerance grade : 1 For controlling test gauges, reference gauges, and for adjusting length measuring instruments as well as for accurate test works in the measuring room. Tolerance grade : 2 Especially suited as workshop and adjusting gauge or for testing of lever gauges, dial indicators and as substitute for fixed snap gauges. All gauge block sets are supplied with a factory calibration certificate which documents the traceability to national standards. Additionally, the gauge block sets of calibration class K are measured interferometrically by a NKO accredited laboratory. Ref. Calibration / Tolerance grade Number per set Contents Nominal size Grading 516-965-70 K 32 pieces 1 1,005-516-966-10 0 9 1,01 ~ 1,09 0,01 516-967-10 1 9 1,1 ~ 1,9 0,1 516-968-10 2 9 1 ~ 9 1 3 10 ~ 30 10 ( 1,1 kg) 1 60 - (3,7 kg) 4 25-100 25 516-941-70 K 103 pieces 1 1,005-516-942-10 0 49 1,01-1,49 0,01 516-943-10 1 49 0,5-24,5 0,5 516-944-10 2 (3,8 kg) 4 25-100 25 516-945-70 K 87 pieces 9 1,001-1,009 0,001 516-946-10 0 49 1,01-1,49 0,01 516-947-10 1 19 0,5-9,5 0,5 516-948-10 2 (3,3 kg) 10 10-100 10 516-961-70 K 47 pieces 1 1,005-516-962-10 0 19 1,01-1,19 0,01 516-963-10 1 8 1,2-1,9 0,1 516-964-10 2 9 1-9 1 (2,8 kg) 10 10-100 10 516-343-10 516-943-10 «CERA BLOCK» gauge blocks sets made of ceramics Gauge blocks made of ceramics, of high stability, lapped, with good adhesive power Each gauge block is provided with an identification number. The hardness of the gauge blocks is 1.350 HV. They are very stable and extremely wear resistant. Each gauge block set is supplied with a factory certificate of calibration which documents the traceability to national standards. Additionally, the gauge blocks are measured interferometrically by a NKO accredited laboratory. Specifications Accuracy : DIN EN ISO 3650 Tolerance grade : K For laboratories Tolerance grade : 0 As reference gauge for controlling workshop gauges blocks. For adjusting high precision measuring instruments. Tolerance grade : 1 For controlling test gauges, reference gauges, and for adjusting length measuring instruments as well for accurate test works in the measuring room. Tolerance grade : 2 Especially suited as workshop and adjusting gauges or for testing of lever gauges, dial indicators and as substitute for fixed snap gauges. All gauge block sets are supplied with a factory calibration certificate which documents the traceability to national standards Additionally, the gauge block sets of calibration class K are measured interferometrically by a NKO accredited laboratory. Calibration/tolerance grade per set lerance grade per set Number Nominal size Grading Calibration/to- Number Nominal size Grading Ref. Contents Ref. Contents 516-342-10 0 49 1,01-1,49 0,01 516-366-10 0 32 pieces 1 1,005-516-343-10 1 49 0,5-24,5 0,5 516-367-10 1 9 1,01-1,09 0,01 516-345-70 K 87 pieces 9 1,001-1,009 0,001 516-368-10 2 9 1,1-1,9 0,1 516-346-10 0 49 1,01-1,49 0,01 9 1-9 1,0 516-347-10 1 19 0,5-9,5 0,5 3 10-30 10 516-348-10 2 10 10-100 10 1 60-516-361-70 K 47 pieces 1 1,005-516-362-10 0 19 1,01-1,19 0,01 516-363-10 1 8 1,2-1,9 0,1 516-364-10 2 9 1-9 1 10 10-100 10 E 70

Individual gauge blocks made of steel E Measuring tools Serie 516 Individual gauge blocks made of steel Made of high quality, especially, alloyed and stress relieved special steel of high stability and good adhesive power. Carefully hardened and lapped, slightly broken edges. The hardness of these gauge blocks is 800 HV (64 HRC) which makes them extremely wear resistant. Specifications Accuracy : DIN EN ISO 3650 Tolerance As reference gauge for controlling workshop gauge blocks. grade : 0 For adjusting high accuracy measuring instruments. Tolerance For controlling test gauges, reference gauges and for adjusting length measuring instruments as well as for accurate test works in the measuring room. grade : 1 When ordering, please always state the suffix of the required tolerance grade. -021 : Tolerance grade 0 and -031 : Tolerance grade 0 Example : 611611-021 Gauge block with nominal size 1, tolerance grade 0 Tolerance grade «K» on request. Special dimensions on request. Gauge blocks from 125 nominal size with connector bores. Nominal Nominal Nominal Nominal Nominal Nominal size size size size size size 0,10 611821 0,51 611892 0,92 611933 1,14 611574 2,0 611612 20,0 611672 0,11 611860 0,52 611893 0,93 611934 1,15 611575 2,5** 611642 20,2** 611855 0,12 611861 0,53 611894 0,94 611935 1,16 611576 3,0 611613 20,5 611660 0,13 611862 0,54 611895 0,95 611936 1,17 611577 3,5 611643 21,0 611631 0,14 611863 0,55 611896 0,96 611937 1,18 611578 4,0 611614 21,5 611661 0,15 611822 0,56 611897 0,97 611938 1,19 611579 4,5 611644 22,0 611632 0,16 611864 0,57 611898 0,98 611939 1,20 611580 5,0 611615 22,5 611662 0,17 611865 0,58 611899 0,99 611940 1,21 611581 5,1** 611850 22,8** 611856 0,18 611866 0,59 611900 0,991 611551 1,22 611582 5,5 611645 23,0 611633 0,19 611867 0,60 611901 0,992 611552 1,23 611583 6,0 611616 23,5 611663 0,20 611823 0,61 611902 0,993 611553 1,24 611584 6,5 611646 24,0 661634 0,21 611868 0,62 611903 0,994 611554 1,25 611585 7,0 611617 24,5 611664 0,22 611869 0,63 611904 0,995 611555 1,26 611586 7,5 611647 25,0** 611635 0,23 611870 0,64 611905 0,996 611556 1,27 611587 7,7** 611851 30,0 611673 0,24 611871 0,65 611906 0,997 611557 1,28 611588 8,0 611618 40,0 611674 0,25 611824 0,66 611907 0,998 611558 1,29 611589 8,5 611648 41,3* 611857 0,26 611872 0,67 611908 0,999 611559 1,30 611590 9,0 611619 50,0 611675 0,27 611873 0,68 611909 1,0 611611 1,31 611591 9,5 611649 60,0 611676 0,28 611874 0,69 611910 1,0005 611520 1,32 611592 10,0 611671 70,0 611677 0,29 611875 0,70 611911 1,001 611521 1,33 611593 10,3** 611852 75,0 611801 0,30 611825 0,71 611912 1,002 611522 1,34 611594 10,5 611650 80,0 611678 0,31 611876 0,72 611913 1,003 611523 1,35 611595 11,0 611621 90,0 611679 0,32 611877 0,73 611914 1,004 611524 1,36 611596 11,5 611651 100,0 611681 0,33 611878 0,74 611915 1,005 611525 1,37 611597 12,0 611622 125,0 611802 0,34 611879 0,75 611916 1,006 611526 1,38 611598 12,5 611652 131,4* 611858 0,35 611826 0,76 611917 1,007 611527 1,39 611599 12,9** 611853 150,0 611803 0,36 611880 0,77 611918 1,008 611528 1,40 611600 13,0 611623 175,0 611804 0,37 611881 0,78 611919 1,009 611529 1,41 611601 13,5 611653 200,0 611682 0,38 611882 0,79 611920 1,01 611561 1,42 611602 14,0 611624 250,0 611805 0,39 611883 0,80 611921 1,02 611562 1,43 611603 14,5 611654 300,0 611683 0,40 611827 0,81 611922 1,03 611563 1,44 611604 15,0** 611625 400,0 611684 0,41 611884 0,82 611923 1,04 611564 1,45 611605 15,5 611655 500,0 611685 0,42 611885 0,83 611924 1,05 611565 1,46 611606 16,0 611626 600,0 611840 0,43 611886 0,84 611925 1,06 611566 1,47 611607 16,5 611656 700,0 611841 0,44 611887 0,85 611926 1,07 611567 1,48 611608 17,0 611627 750,0 611842 0,45 611828 0,86 611927 1,08 611568 1,49 611609 17,5 611657 800,0 611843 0,46 611888 0,87 611928 1,09 611569 1,5 611641 17,6** 611854 900,0 611844 0,47 611889 0,88 611929 1,10 611570 1,6 611516 18,0 611628 1000,0 611845 0,48 611890 0,89 611930 1,11 611571 1,7 611517 18,5 611658 0,49 611891 0,90 611931 1,12 611572 1,8 611518 19,0 611629 0,50 611506 0,91 611932 1,13 611573 1,9 611519 19,5 611659 * Special dimensions for the testing of caliper gauges ** Special dimensions for the testing of external screw type micrometers E 71

Individual gauge blocks made of ceramics Serie 516 «Cera Block» Individual gauge blocks made of ceramics Each gauge block is supplied with a factory certificate of inspection. Specifications Accuracy : DIN EN ISO 3650 Tolerance grade : 0 Tolerance grade : 1 As reference gauge for controlling workshop gauge blocks. For adjusting high accuracy measuring instruments. For controlling test gauges, reference gauges and for adjusting length measuring instruments as well as for accurate test works in the measuring room. When ordering, please always state the suffix of the required tolerance grade. -021 : Tolerance grade 0 and -031 : Tolerance grade 0 Example : 613611-021 Gauge block with nominal size 1, tolerance grade 0 Tolerance grade «K» on request. Special dimensions on request. Gauge blocks from 125 nominal size with connector bores. Nominal size Nominal size Nominal size Nominal size Nominal size 0,50 613506 1,10 613570 1,40 613600 8,5 613648 21,5 613661 0,991 613551 1,11 613571 1,41 613601 9,0 613619 22,0 613632 0,992 613552 1,12 613572 1,42 613602 9,5 613649 22,5 613662 0,993 613553 1,13 613573 1,43 613603 10,0 613671 22,8** 613856 0,994 613554 1,14 613574 1,44 613604 10,3** 613852 23,0 613633 0,995 613555 1,15 613575 1,45 613605 10,5 613650 23,5 613663 0,996 613556 1,16 613576 1,46 613606 11,0 613621 24,0 613634 0,997 613557 1,17 613577 1,47 613607 11,5 613651 24,5 661664 0,998 613558 1,18 613578 1,48 613608 12,0 613622 25,0** 613635 0,999 613559 1,19 613579 1,49 613609 12,5 613652 30,0 613673 1,0 613611 1,20 613580 1,5 613641 12,9** 613853 40,0 613674 1,0005 613520 1,21 613581 1,6 613516 13,0 613623 41,3* 613857 1,001 613521 1,22 613582 1,7 613517 13,5 613653 50,0 613675 1,002 613522 1,23 613583 1,8 613518 14,0 613624 60,0 613676 1,003 613523 1,24 613584 1,9 613519 14,5 613654 70,0 613677 1,004 613524 1,25 613585 2,0 613612 15,0** 613625 75,0 613801 1,005 613525 1,26 613586 2,5** 613642 15,5 613655 80,0 613678 1,006 613526 1,27 613587 3,0 613613 16,0 613626 90,0 613679 1,007 613527 1,28 613588 3,5 613643 16,5 613656 100,0 613681 1,008 613528 1,29 613589 4,0 613614 17,0 613627 125,0 613802 1,009 613529 130 613590 4,5 613644 17,5 613657 131,4* 613858 1,01 613561 1,31 613591 5,0 613615 17,6** 613854 150,0 613803 1,02 613562 1,32 613592 5,1** 613850 18,0 613628 175,0 613804 1,03 613563 1,33 613593 5,5 613645 18,5 613658 200,0 613682 1,04 613564 1,34 613594 6,0 613616 19,0 613629 250,0 613805 1,05 613565 1,35 613595 6,5 613646 19,5 613659 300,0 613683 1,06 613566 1,36 613596 7,0 613617 20,0 613672 400,0 613684 1,07 613567 1,37 613597 7,5 613647 20,2** 613855 500,0 613685 1,08 613568 1,38 613598 7,7** 613851 20,5 613660 1,09 613569 1,39 613599 8,0 613618 21,0 613631 * Special dimensions for the testing of caliper gauges ** Special dimensions for the testing of external screw type micrometers E 72

Gauge block accessory E Serie 516 Gauge block accessory This accessory offers an additional range of application for the representation of cylindrical limit gauges and the direct size transmission onto workpieces. Complete set : 516-601 P consisting of 22 parts 516-602 P consisting of 14 parts Delivery in a wooden box Part designation Quantity Holder 516-601 consists of 516-602 consists of 15-60 619002 P 1-5-100 619003 P 1 15-160 619004 P 1 20-250 619005 P 1 Holder base 35 619009 P 1 Semi circular jaws Radius 2 619010 P 2 Radius 5 619011 P 2 Radius 8 619012 P 2 Radius 12 619013 P 2 - Radius 20 619014 P 2 - Flat jaws 160 619018 P 2 - Scriber 619019 P 1 Centering tip 619020 P 1 Control tips 619021 P 2 - Straight edges with 3 measuring edges 100 619022 P 1 160 619023 P 1 - Mass kg - 5,6 4,6 E 73

Steel micrometer gauge block set made of ceramic Serie 516 Steel micrometer gauge block set made of ceramic Gauge block sets with optical glass parallel. For adjusting and calibrating micrometers according to DIN 863 Specifications Accuracy : DIN EN ISO 3650 Delivery in a wooden box Including 1 piece optical glass parallel no. 157-101, nominal size 12, ø 30 Tolerance Number Nominal Contents pcs. grade per set size 516-156-10 0 10 1 2,5 516-157-10 1 1 5,1 1 7,7 1 10,3 1 12,9 1 15,0 1 17,6 1 20,2 1 22,8 1 25,0 516-156-10 Optional accessory 516-607 Gauge block holder 516-607 Ceramic caliper testing kit For testing the accuracy of calipers according to DIN and/or VDI/VDE/DGQ 3650. Including 3 gauge blocks and 2 ring gauges made of ceramics. Specifications Gauge blocks : Accuracy according to DIN EN ISO 3650 Delivery in a wooden box and a pair of gloves. Nominal size Tolerance grade Mass kg 516-150-10 30, 41,3 and 131,4 1 1,72 Ring gauge ø 4 and 25 material : ceramic 516-150-10 Serie 516 Maintenance set Contains everything you need for maintaining steel gauge blocks. Including : 516-650 600001 Rust preventive oil in spray spraying can (appr. 100 ml) 601645 «CERASTON» 100 x 25 x 12 158-117 Optical flat glas ø 45 x 12 600004 Hand tweezers 600005 Bellow 600006 Paper cloth 600007 Leather cloth 600008 Plastics dropping bottle for cleaning solvent (100 ml) 600009 Pair of gloves Consoable Spares 601644 «CERASTON»* 150 x 50 x 20 601645 «CERASTON»* 100 x 25 x 12 * Stone for removing burrs on steel gauge blocks 516-650 Sample application E 74

Precision test gauge set E Serie 926 Precision test gauge set Accuracy DIN 2269 Complete measuring set of universal test gauges, consisting of 273 pieces for use in the control room, work on jig drill or in tool and fixture engineering. From dia. 0.99-10.01, rising by 0,1, each test gauge delimited by test gauges at + 0.01 (oversize) and -0.01 (undersize). Specifications Accuracy : DIN 2269 Hardness : HRC 60-62 Finish : very fine ground from dia. 3 inscribed Roughness : < 0,1 µm Ra Length : up to dia. ø 6 = 50 over dia. ø 6 = 70 Made from alloyed tool steel, hardened. Delivery in a wooden box. 926-210 Individual test gauges on request Degree of accuracy 926-210 1 926-212 2 Serie 926 Accuracy DIN 2269 Complete set of test gauge, consisting of 91 pieces From dia. 1-10, rising by 0,1 Specifications Accuracy : DIN 2269 Hardness : HRC 60-62 Finish : very fine ground from dia. 3 inscibed Roughness : < 0,1 µm Ra Length : up to ø 6 = 50 over ø 6 = 70 Delivery in a wooden box. Made from alloyed tool steel hardened. 926-222 Individual test gauges on request Degree of accuracy 926-220 1 926-222 2 E 75

Magnifiers 28504 Magnifying glasses Lens : Silicated glass Mount : plastic shock proof aeration hole Biconvex lens 25 ø MAGNIFICATION x 2,5 x 3 x 4 x 5 x 7 x 10 28505 Same as 28504, convex plan Lens ø 16, plastic mounting MAGNIFICATION x 12 x 15 28506 Biconvex lens, 30 ø MAGNIFICATION x 4 x 5 x 7 x 10 28507 Aplanetic optic 23 ø MAGNIFICATION x 6 x 10 28504 28505 28506 28507 28511 Precision measuring magnifier Silicated glass - Aplanetic optic, 30 ø 7 differents measuring plates Delivered with measuring plate 7151 28511 28512 Magnifier with lightening Silicated lens, biconvex, 2 batteries LR 06 ø 75 5x ø 90 3x 28512 E 76

Magnifiers E Magnifier stand Lens : Mount : Silicated glass Nickeled brass Foot : Iron stand ø 130, flexible steel tube 300 length 28628 Biconvex lens 28629 Aplanetic optic 28628 Lens ø MAGNIFICATION 2 x 2,5 x 3 x 3,5 x 4 x -/75 75 -/90 90 -/100 100 -/120 120 28629 -/65 65 -/75 75 28628 28629 TK With table clamp + TK TK 28631 Magnifier with stand Lens : Mount : Aspheric ø 60, 4 x Plastic round stand 70 ø 70, height 60. 28632 As 28631, with aplanetic optic 30 ø, 10 x ø 45, height 50. 28631 28632 28633 Magnifiers de mesure de précision Aplanetic optic, silicated glass 23 ø lens, 8 x Mount-stand : plastic, height ca.45. 28634 As 28633, with measuring plate, steel. Division 0,1, length 15 with 150 pitch line. 28633 28634 E 77

Magnifiers Magnifiers 28701 Aplanetic optic, lens ø 30, 10 x Mount FU6 : Plastic mounting, round ø45, height 50, measuring scale 15. Division 0,1. 28701 28702 Micro magnifier with achromatic Lens magnification : 40-50-60 x, length 150 Rotating ring for focusing. 28702 Compte-fils Messing, satin, chromed finish Lens : silicated glass, biconvex Precision finishing 28703 to 28707 With square opening without division in. 28708 As 28705 with 2 sides of opening with division. 28709 As 28705, with aplanetic optic round opening silicated glass with measuring scale, division 0,1 - length 10 with 100 pitch-lines of 0,1 28703 à 28707 + 28309 28710 As 28709, with square scale, measuring precision 1/10. Opening () Height () Magnification 28703 10 x 10 23 12 x 28704 15 x 15 27 10 x 28705 20 x 20 33 8 x 28706 25 x 25 42 6 x 28707 30 x 30 53 5 x 28709 28710 28709 20 ø 35 8 x Biconvex folding magnifier Lens : silicated glass Stanless steel protection 28711 3 x 1 lens ø 30 28712 3 x + 3 x + 3 x = 9 x 3 lenses ø 30 28711 28713 E 78

Magnifiers E Aplanetic folding magnifier Lens : silicated glass Mount : plastic mounting. Box : Plastic black, shock proof. 28715 Aplanetic optic. 28714 2 lenses convex, aplanetic optic Lens ø 3x + 3x = 6x 3x + 5x = 8x MAGNIFICATION 4x + 6x = 10x 5x + 7x = 12x 7x + 8x = 15x 10x + 10x = 20x 28714/16 16,3 -/8 -/10 -/12 -/15 -/20 28714/23 22,8 -/6 -/8 -/10 -/12 -/15 28715 22,8 -/6 -/8 -/10 -/12 Stainless steel protection 28716 Aplanetic optic 28717 Achromatic optic Lens ø MAGNIFICATION 6x 8x 10x 12x 15x 20x 28716/16 16,3 -/6 -/8 -/10 -/12 -/15 -/20 28716/23 22,8 -/6 -/8 -/10 -/12 -/15 28717/23 22,8 -/6 -/8 Grip magnifier Lens : silicated glass Plastic mounting 28718 Aplanetic optic Lens ø MAGNIFICATION 4x 5x 6x 10x 15x 28718/23 22,8 -/10 28718/23 22,8 -/15 28718/30 30 -/6 28718/40 40 -/5 28718/50 50 -/4 Bi-ocular 28719 Holded frame fitted, steel adjustable head band. MAGNIFICATION 1 x 1,5 x 2 x 2,5 x 3 x E 79

Stereo microscope Serie 377 Stereo microscope MSM-400 Bright, sharp images with real depth are recreated with high resolution and excellent faithfulness to color, thus minimizing eye fatigue while increasing inspection efficiency and productivity. The magnification can be adjusted depending on type of instrument with a user-friendly magnification switch (MSM-412, -465) or a zoom objective (MSM-Z414L) to the appropriate requirements. Continuous zooming, a standard feature, allows you to enlarge the object by 10 to 40 times in total magnification. Using the horizontal focusing handles mounted on both sides of the unit, you can quickly bring the object into focus regardless of whether you re right- or left-handed. The handles are so also used for coarse and fine focusing controls. The MSM-465 comes with a focusing-torque adjustment mechanism. The microscopes can be connected to a digital camera or CCD camera to save captured images of the object or for simultaneous observation through different media. Standard accessory : two eye shades, dust cover. Model MSM-412 MSM-Z414L 377-925 K 377-946 D Optical system Greenough type, erect, unreversed image, inward inclination angle 12 Binocular, viewing angle 45, adjustable Binocular, viewing angle 45, adjustable Optical tube interpupillary distance between interpupillary distance between 54 and 76, adjustable dioptre balancing. 54 and 76, adjustable dioptre balancing (left eyepiece only) (right and left eyepieces) Magnification switch system Turret, two stage Magnification variation by zoom Lens systems 1x, 2x (turret) 1x à 4x (zoom ratio : 4) Auxiliary lens systems (optional) - 0,5 x, 0,75 x, 1,5 x Eyepiece WF10x (Visual field no. : 20, standard), WF5x (Visual field no. : 22), WF15x (Visual field no. : 13), WF20x (Visual field no. : 10) Total magnification 10x, 20x (with 10x standard eyepiece) 10x à 40x (with 10x standard eyepiece) Working distance 95 80 Height adjustment range 44 Transmitted illumination Light source : Halogen lamp (12V, 10W), with color filter Refected illumination Light source : Halogen lamp (12 V, 15W) Power supply 220 V AC, 50/60 Hz Power consumption 20 W Total weight 4,7 kg 5,1 kg Consumable Spares : 011298 MC special cleaner for laboratory and photo optics, microscopes (120 ml) More detailed information on these and other products can be found in the product brochures. E 80

Stereo microscope E Serie 377 Stereo microscope MSM-400 Standard accessory : two eye shades, dust cover Model Optical system Optical tube Magnification switch system Lens systems Auxiliary lens systems (optional) Eyepiece Total magnification Working distance Height adjustment range Total weight MSM-465 377-965 K Parallel System, erect, unreversed image Binocular, viewing angle 45, adjustable interpupillary distance between 54 and 76, adjustable dioptre balancing (left eyepiece only) Turret, four stage 0,6 x, 1,2 x, 2,5 x, 5 x (turret) 0,5 x, 1,5 x, 2 x WF10x (visual field no. : 23, standard), WF6,25x (visual field no. : 23), WF15x (visual field no. : 17,6), WF20x (visual field no. : 13,4), WF32x (visual field no. : 10) 6 x, 12 x, 25 x, 50 x (with 10x standard eyepiece) 89 50 6,3 kg E 81

Measuring microscope «TM-500» Serie 176 Measuring microscope «TM-500» Standard accessory 176-116 Eyepiece 15 x 176-138 Objective 2 x 176-206 Cross slide table XY 50 x 50 (176-811 CED) 176-207 Cross slide table XY 100 x 50 (176-812 CED) Pre-installed cross slide table, without integrated Consumable Spares 011298 MC Special cleaner for laboratory and photo optics, microscopes (120 ml). 176-811 CED With integrated micrometers (152-390/152-389 optional accessories) Model TM-505 TM-510 176-811 CED 176-812 CED XY measuring range 50 x 50 100 x 50 Measuring system Integrated micrometers Max. workpiece height 115 107 Max. workpiece weight 5 kg Angle reading 360 (Graduation 6 via nonius) Eyepiece 15 x Objective 2 x Magnification 30 x Transillumination 24 V, 2 W intensity adjustable Incident illumination 24 V, 2 W intensity adjustable Dimensions 210 x 333 x 391 240 x 333 x 391 Mass 13,5 kg 14,5 kg Serie 176 Objective Objective Eyepiece 10x (176-115) Eyepiece 15x (176-116)* Eyepiece 20x (176-117) 2 x (176-138)* 20 x (6,5 ) 30 x (6,5 ) 40 x (5,0 ) 5 x (176-139) 50 x (2,6 ) 75 x (2,6 ) 100 x (2,0 ) 10 x (176-137) 100 x (1,3 ) 150 x (1,3 ) 200 x (1,0 ) * = Standard accessory The values in brackets refer to the field size. E 82

Profile projector PJ-A3000 E Serie 302 Profile projector PJ-A3000 Table instrument for testing small and medium sized workpieces. Vertical, rotatable cross lines screen. Easy to operate coordinate measuring stage with coarse and fine adjustment. Direct and clear, easy to read XY digital at eye level ensures safe and faultless measurement. Halogen transillumination and incident illumination are integrated into the housing. Provided with a protractor as standard. Standard accessory 172-202 10 x Objectives 12AAD990 Measuring stage (PJ-A3005 F-150) 319-225-1 Measuring stage (PJ-A3010 F-200) 515530 3 x Halogen lamps (24 V/150 W) 383876 Protective hood 930919 Light shield Consumable Spares 011298 MC special cleaner for laboratory and photo optics, microscopes (120 ml) Model PJ-A3000 Serie Screen Diameter 315 Protractor Switchable degree/decimal, Resolution : switchable 0,01 /1 - Display range : ± 360 (count up to ± 370 ) Functions ABS/INC switch, ZERO Uncertainty of magnification 0,1 % transillumination, 0,15% incident illumination Illumination Lamps Halogen lamp (24 V, 150 W) Illumination system Telecentric Power supply 230 V, 50/60 Hz Mass PJ-A3005F-150 : 116 kg; PJ-A3010F-200 : 140 kg Specifications coordinate measuring stage Model PJ-A3005F-150 PJ-A3010F-200 302-701 D Direct reading of measurement data on the 6 digit digital display enables safe and faultless measuring. Built in protractor, switchable for reading in degrees or decimal reading. Resolution : 1 or 0,01. 302-702 D 302-701 D Measuring range XY axes 150 x 50 200 x 100 Resolution 0,001 Measuring system Built in glass scale Stage size 280 x 152 380 x 250 Max. workpiece height up to 103,5 up to 92,5 Max. workpiece weight 5 kg Functions ZERO setting +/- direction choice RS-232 C Interface X axes displacement XY axes displacement E 83

ABSOLUTE «Linear Scale» Digital length measuring system Serie 539 ABSOLUTE «Linear Scale» Digital length measuring system AT 715 Version with ABSOLUTE system Measuring range 100-1800 Specifications Connection : Accuracy (20 C) 7 µm Max. processing speed : 50 m/min Resolution : 1 µm Operation temperature : 3 to 45 C Protection : IP-55 Sliding force : < 5 N Standard accessory Mounting set for type AT 715 Extension cable : 2 m 09AAB674A 5 m 09AAB674B 7 m 09AAB674C Exclusively to KA-counter 174-173 D 174-175 D Legend Effective measuring : (L 0 ) Bore center distance : (L 2 ) Max. measuring head displacement : (L 1 ) Total length : (L 3 ) (L 0 ) (L 1 ) (L 2 ) (L 3 ) Signal cable (L 0 ) (L 1 ) (L 2 ) (L 3 ) Signal cable 539-801 100 120 258 278 3,5 m 539-815 800 840 978 998 3,5 m 539-802 150 170 308 328 3,5 m 539-816 900 940 1078 1098 3,5 m 539-803 200 220 358 378 3,5 m 539-817 1000 1040 1178 1198 5,0 m 539-804 250 270 408 428 3,5 m 539-818 1100 1140 1278 1298 5,0 m 539-805 300 330 468 488 3,5 m 539-819 1200 1240 1378 1398 5,0 m 539-806 350 380 518 538 3,5 m 539-820 1300 1340 1478 1498 5,0 m 539-807 400 430 568 588 3,5 m 539-821 1400 1440 1578 1598 5,0 m 539-808 450 480 618 638 3,5 m 539-822 1500 1540 1678 1698 5,0 m 539-809 500 540 678 698 3,5 m 539-823 1600 1640 1778 1798 5,0 m 539-811 600 640 778 798 3,5 m 539-824 1700 1740 1878 1898 5,0 m 539-813 700 740 879 898 3,5 m 539-825 1800 1840 1978 1998 5,0 m 539-814 750 780 918 938 3,5 m E 84

«Linear Scale» Digital display unit E Serie 174 «Linear Scale» Digital display unit KA Counter Easy to operate and multifunction display unit. Specifications Resolution : 0,005, 0,001 Connectable Linear Scale : AT 100 Series AT 700 Series Display : 7 digits, sign (-) 174-173 D Operation 0 C to 45 C temperature : Axes Dimensions (WxHxD) Mass kg 174-173 D 2 260 x 167 x 80 1,1 174-175 D 3 260 x 167 x 80 1,2 Optional accessories 938140 Signal probe with clamping shaft ø 20 935094 Signal probe with clamping shaft ø 32 09CAB217 RS-232 C output 0114418 Footswitch for KA Counter for data output 09CAB217 09CAB231 Adapter for micrometer head 164--122 Signal probe For setting the zero point in linear-scale display devices. For holding the current value on the display on contact with the workpiece. 938140 Shaft diameter Ball diameter Connecting cable 938140 20 10 ± 0,002 3 m 935094 32 10 ± 0,002 3 m E 85

Surface roughness tester Surface roughness tester «Surftest SJ-201 P» The portable surface roughness tester «Surftest SJ-201 P» has been designed for fast and easy testing of surface roughness parameters. In order to perform a multitude of different measuring tasks a large selection of probes and nosepieces are available. The drive unit can be separated from the main measuring unit allowing for measurements in hard to reach narrow spaces, too. The SJ-201 P may be operated on AC/DC as well as anywhere on the shop floor independent of stationary power supply on battery. The SJ-201 P features RS-232 C interface and DIGIMATIC port as standard equipment. The roughness data collected may therefore be processed iediately with or without external PC and other Mitutoyo hardware. Interfaces and operating panel can be safely locked away under protective coverings when the SJ-201 P is not in use. The Auto-Sleep function starts saving battery power after 30 seconds without panel activity. 178-930-2 D Model Type SJ-201 P 178-930-2 D Basic model SJ-201 S 178-899-2 D Transversal scan SJ-201 R 178-995 D Front lift model Optional accessory 178-420 D External printer Note : The feed units SJ-201 P and SJ-201 S are compatible with one another Keyboard (protective covering opened Rear view External printer E 86

Surface roughness tester E Serie 178 Surface roughness tester «Surftest SJ-301» Portable surface roughness tester featuring dustprotected, touch-sensitive operation panel and inegrated printer. The large LCD-window makes it easy to read measurement result and analysis graphs at a glance. The profile speed thermal printer prints out clear and fast. Designed to increase operability - the large keypads are used for measuring operations, while the touch panel LCD (special operating pen included) is used for setting various measuring conditions. Five different measuring conditions can be stored by the SJ-301. Measurement data may be downloaded to an external PC. Adheres to international standards : DIN, ISO, ANSI and JIS. Measurement data may be stored ieditely and evaluated at later point in time and/or printed. An optional memory card is available for storing up to 20 sets of measurement conditions, measuring and statistic data. 178-952-3 D Model Type SJ-3010 178-952-3 D Basic model SJ-301 S 178-939-2 D Transversal scanning SJ-301 R 178-990 D Front lift model Note : The feed units are compatible with one another. E 87

Engineers levels Engineers levels - 2 graduated vials - With V-groove in the contact surface DIN 877 Length /m 160 200 250 300 500 26701 Accuracy 0,3 26702 Accuracy 0,1 26703 Accuracy 0,04 26704 Accuracy 0,02 26705 Accuracy 0,01-26706 Wood case 26701 Frame levels with groove - with 2 vials Length 100 x 100 150 x 150 200 x 200 300 x 300 26707 Accuracy 0,3 26708 Accuracy 0,1 26709 Accuracy 0,04 26710 Accuracy 0,02-26711 Accuracy 0,01 - - 26712 Wood case 26707 25123 Electronic spirit levels Accuracy 1 DIGIT = 0,01 per m. Quick reading 3 Wood case 25123 Level, lg 160 25124 Level, lg 200 25125 Frame levels, lg 200 25125 26713 Crank pin levels Length 60 90 120 150 Accuracy 0,6 x 0,8 0,3 x 0,8 0,3 x 0,8 0,3 x 0,8 High accuracy 0,2 x 0,8 0,1 x 0,8 0,2 x 0,8 0,1 x 0,8 Wood case 22,90 26,38 29,87 31,35 26713 E 88

lectronic inclinometer E Electronic inclinometer TESA ClinoBEVEL 1 Userfriendly, versatile inclinometer for inspecting inclination or comparative mode - Measuring range ± 45 with angle play - Reinforced aluminium housing and new electronics for error free read -out. 05330201 TESA ClinoBEVEL 1 ± 45 Optional accessories /m > 0,02 Length basis in 100 and 75 05360004 RS 485 connection cable, length 1,5 m 05360005 RS 485 adapter to RS 232 05360006 Cable with key for HOLD 04768002 4 batteries 1,5 V, type LRC 6, AA TESA MICROBEVEL 1 These electronic inclinometers are intended for precisely, e.g flatness measurements on surfaces urements of geometrical features on machines rough environments. Length basis width /m 05330003 Horizontal model 110 45 0,01 et 0,001 1,8 05330004 Horizontal model 150 45 0,01 et 0,001 2,1 05330005 Square model 150 45 0,01 et 0,001 3,1 Models with numerical intervals to 0,05 and 0,005 /m also available Optional accessory 04768002 4 batteries 1,5 V, type LRC 6, AA kg Range /m /m G = /m 1 ± 20 ± 5 0,01 G = 1% 2 ± 2 ± 2 0,001 G = 0,01 ( 2 measuring) within the local rnage E 89

Surface plates Cast iron 26501 DIN 876/1 - Fine grained planed 26502 DIN 876/2 - Normal grained planed 26503 DIN 876/3 - Close grained planed Dimensions Weight kg Dimensions Weight kg Dimensions Weight kg 300 x 200 8 500 x 800 80 1000 x 1000 250 250 x 250 9 600 x 700 80 1500 x 500 150 300 x 300 12,5 600 x 800 100 1500 x 700 250 300 x 400 20 1000 x 400 85 1500 x 1000 400 500 x 300 28 1000 x 500 115 2000 x 1000 800 400 x 400 28 800 x 800 150 2500 x 1000 1200 500 x 400 35 1000 x 700 150 3000 x 1000 1400 500 x 500 45 1000 x 800 180 2000 x 1500 1350 400 x 600 45 900 x 900 170 2500 x 1500 1600 400 x 700 55 1200 x 800 230 3000 x 1500 2100 500 x 600 55 1200 x 1000 300 2000 x 2000 2300 500 x 700 70 26501 26502 26503 26508 26508 Adjustable feet for surfaces plates Cast iron - min 700 - max 800 Angle plates from special cast iron Accuracy I (Fine grained planed) Accuracy II (Normal grained planed) Accuracy III (closed grained planed) Dimensions 25707 DIN 876/1 25708 DIN 876/2 25709 DIN 876/III 100 x 100 100 150 x 150 150 On request 200 x 200 200 25707 Dimensions 25707 DIN 876/I 25708 DIN 876/II 25709 DIN 876/III 300 x 300 300 On request 500 x 500 500 Triangular straight edges DIN 876/1 26603 26604 Length x width 60 Length x width 45 250 x 45 250 x 50 500 x 60 500 x 75 750 x 80 750 x 95 1000 x 100 1000 x 20 26603 26605 Straight edges DIN 876/1 Length 500 750 1000 1500 2000 Width 40 45 50 60 70 26605 E 90

Black granite surface plates E Black granite surface plates Size Kg Grade µm Grade µm Grade µm Grade µm Grade µm Grade µm 3 2 1 0 00 000 PN 300 x 200 x 50 9 0001 30 0002 15 0003 7 0004 3,5 0005 1,7 0006 1,3 PN 400 x 250 x 60 18 0007 32 0008 16 0009 8 0010 4 0011 2 0012 1,5 PN 400 x 400 x 60 28 0013 34 0014 17 0015 9 0016 4,5 0017 2,2 0018 1,6 PN 500 x 315 x 60 33 0019 34 0020 17 0021 9 0022 4,5 0023 2,2 0024 1,6 PN 500 x 500 x 80 60 0025 39 0026 20 0027 10 0028 5 0029 2,5 0030 1,8 PN 630 x 400 x 80 60 0031 39 0032 20 0033 10 0034 5 0035 2,5 0036 1,8 PN 630 x 630 x 100 118 0037 42 0038 21 0039 10 0040 5 0041 2,6 0042 1,9 PN 800 x 500 x 100 120 0043 44 0044 22 0045 11 0046 5,5 0047 2,8 0048 2 PN 1000 x 630 x 140 260 0049 49 0050 24 0051 12 0052 6 0053 3,1 0054 2,2 PN 1000 x 1000 x 160 480 0055 56 0056 28 0057 14 0058 7 0059 3,5 0060 2,5 PN 1200 x 800 x 160 460 0061 56 0062 28 0063 14 0064 7 0065 3,5 0066 2,5 PN 1600 x 1000 x 180 860 0067 66 0068 33 0069 16 0070 8 0071 4,1 0072 2,9 PN 2000 x 1000 x 220 1300 0073 75 0074 38 0075 19 0076 9,5 0077 4,7 0078 3,3 PN 2000 x 1500 x 250 2250 0079 80 0080 40 0081 20 0082 10 0083 5 0084 3,5 PN 2500 x 1500 x 300 3300 0085 92 0086 46 0087 23 0088 11,5 0089 5,8 0090 4 Black granite surface plates are manifactured in several accuracy grades : «3», «2», «1», «0», «00» and «000» according to standard ISO 8512-2 in order to satisfy all specific needs of the user, be it a workshop or a metrological office. All plates are tested with electronic levels or laser autocollimator in a temperature (20 C) and humidity controlled environment. All plates «Microplan Group» are supplied with a test report in which error map and installation instructions are related. When required, we can supply a test report grant from an authorised organisation. The table hereunder shows the standard sizes, the reference codes and the absolute flatness tolerances (in thousandths of.). We can supply plates with different sizes according to the customer s needs and drawings with holes, glued threaded inserts, T-slots, clearing grooves and with rubber feet for the smaller sizes. To grant a complete service, Microplan Group usually makes special machining according to drawings, fields of working and needs of the Customer. The main special granite workings are: gluing with epoxy of steel or stainless steel inserts and T-slots according the hereunder table; drilling: granite drilling for full or through holes (from ø 3 to 300 ); milling with fitted diamond tools (in accordance with the limits of the metal milling). ATTENTION: For Grade «00» and «000» thickness are higher! The sizes underscored in yellow meet the standard ISO 8512-2 Supports for plates Cl : adjustable columns for surface plates. Made from a highly resistant compressed cement agglomerate. Adjusting screws ø M30 x 2 with a nut lock and an oscillating on (polished steel). Colour : RAL 5021 and black. 0255 Adjustable high : 480-580 ø Base ø : 200 0256 Adjustable high : 680-780 ø Adjustable high : 220 TN : Support table type Constructed with welded and laminated steel sections with 5-4 vibration damper feet. Colour : Ral 5021 Size Kg TN 0260 630 x 400 14 TN 0261 630 x 630 14 TN 0262 800 x 500 16 TN 0263 1000 x 630 18 TN 0264 1000 x 1000 20 TN 0265 1200 x 800 25 TN 0266 1600 x 1000 28 TN 0267 2000 x 1000 30 E 91

Support with drawers Support for surface plates - table with drawers Like the previous model but with locking drawers 500 x 500 in sheet steel and lock. Until 1000 x 1000, with one drawer. Beyond 1200 x 800, with two drawers. Colour : Ral 5021. Plate size Kg Drawers TC 0270 630 x 360 17 1 TC 0271 800 x 500 19 1 TC 0272 1000 x 630 21 1 TC 0273 1000 x 1000 23 1 TC 0274 1200 x 800 31 2 TC 0275 1600 x 1000 34 2 TC 0276 2000 x 1000 36 2 TC 0277 Tiroir 3 - Support cupboard type Built with welded steel with walls of sheet iron wih two doors and one shell inside. With 5 adjusting screws and 4 vibration damper feet. Colour Ral. 5021 Plate size Kg TA 0285 1000 x 630 61 TA 0286 1000 x 1000 63 TA 0287 1200 x 800 76 TA 0288 1600 x 1000 84 TA 0289 2000 x 1000 91 Black granite squares Perfect for perpendicularity testing, set squares are extremely limited tolerances and the stability of the base. Holes are made in larger versions to reduce weight and facilitate the transport. The tolerance of the lateral faces is ± 0,02 Size µm µm SQ 0196 300 x 200 x 40 6,4 7,8 SQ 0197 400 x 250 x 50 7,2 8,4 SQ 0198 500 x 315 x 60 8 9 SQ 0199 630 x 400 x 60 9 9,6 Size µm µm Kg SQ 0200 200 x 150 x 30 2,4 2 1,8 SQ 0201 300 x 200 x 40 2,6 2 4,7 SQ 0202 400 x 250 x 50 2,8 2 10 SQ 0203 500 x 315 x 60 3 3 17 SQ 0204 630 x 400 x 60 3,2 3 28 SQ 0205 800 x 500 x 80 3,6 4 63 SQ 0206 1000 x 630 x 100 4 4 117 SQ 0207 1200 x 800 x 140 4,4 5 210 SQ 0208 1500 x 1000 x 160 6 6 480 E 92

Linear and level parallel rules E Rules in black granite For high precision testing of linearity, for comparing guides or lapped surfaces. Their shape has been studied to give maximum stability. The lapping on one face is carried out to three levels of precision with tolerances as shown beneath. They can be supplied with handles on the heads. Size Kg Grade 1 µm Grade 0 µm Grade 00 µm RL 300 x 30 x 50 1,3 0150 6,4 0151 3,2 0152 2,6 RL 400 x 40 x 60 2,2 0153 7,2 0154 3,6 0155 2,8 RL 500 x 50 x 80 5 0156 8 0157 4 0158 3 RL 630 x 50 x 80 7 0159 9 0160 4,4 0161 3,2 RL 800 x 50 x 100 10,5 0162 10,4 0163 5,2 0164 3,6 RL 1000 x 60 x 120 15 0165 12 0166 6 0167 4 RL 1400 x 60 x 150 35 0168 15,2 0169 7,6 0170 4,8 RL 1600 x 80 x 180 53 0171 16,8 0172 8,4 0173 5,2 RL 2000 x 80 x 200 89 0174 20 0175 10 0176 6 Level parallel rules in black granite Manufactured with two H-shaped lapped parallel surfaces to ensure stability and lightness. The three levels of tolerances are shown in the table. The parallelism tolerance is equal to the flatness. If required, they can be supplied with handles on the heads. Size Kg Grade 1 // µm Grade 0 // µm Grade 00 // µm RP 500 x 50 x 80 5 0180 8 0181 4 0182 3 RP 750 x 50 x 100 7,5 0183 10 0184 5 0185 3,4 RP 1000 x 60 x 140 16 0186 12 0187 6 0188 4 RP 1500 x 80 x 180 40 0189 16 0190 8 0191 5 RP 2000 x 100 x 220 80 0192 20 0193 10 0194 6 Pair of V-prismis 90 in black granite Ideal for testing cylinders. The tolerances in the table (in thousandths of a millimetres refer to the flatness of the base and the parallelism between the base and the axis of the V-shaped grove. On request, other faces can be lapped. Art. 992 Size Kg µm // µm PRO 240 100 x 70 x 50 1 ± 2 ± 4 PRO 241 140 x 100 x 60 2 ± 2 ± 4 PRO 242 200 x 140 x 70 6 ± 3 ± 6 Cross-point support (Pair) for concentricity test bench MEEHANITE WA structure standardised anti-wear. Steel tube in cemented Ni-Cr. Points with attachment C.M.2. Parallelism between the axis point and the base 0,01. Point alignment ± 0,01. Overall dimension : 350. Key 16. H Kg CPO 385 150 23 CPO 386 200 28 CPO 387 250 42 E 93

Cleaning products Concentricity test bench U max. H L W T Kg BC 0140 300 150 700 250 100 76 BC 0141 600 150 1000 300 140 149 BC 0142 1100 150 1500 350 180 307 BC 0143 1600 200 2000 400 220 556 BC 0144 2100 200 2400 500 250 928 Cleaning paste for granite - T20510 Specific product for the cleaning and maintenance of granite instruments. Its special formula avoids any cause of friction and wear, and it assures an improvement in the sliding of fittings on the granite and a perfect cleaning. A small quantity is enough to properly prepare granite surface. It is supplied in a box of 300 cc with a threaded cap. (Minimum order : 3 pcs) Liquid detergent for granite - DT0520 Liquid detergent for daily cleaning of granite instruments. With spray, 1 litre. (Minimum order : 5 pcs) E 94

Hand tally counter E Hand tally counters Zero setting with turning knob For counting number of persons or pieces up to 9999 N Type Digits Digit height ø Mass Kg 2116 101 With chain 4 4,5 55 0,07 2116 102 With ring 4 4,5 55 0,07 2116 102s With ring 4 4,5 55 0,06 < < Press counters Zero setting with detachable key Stroke move 7 250 digits max. p. minute N Digits Digit height Mass Kg 2118 101 6 4,0 60 x 67 30 0,20 < < < < Revolution counters Zero setting with turning knob Addition in one direction Subtraction with reverse turn < N < N max. 1/min / rpm Digits Digit height ø axe < < < < Mass Kg Right drive 2115 103 2115 203 2000 5 4,5 4,0 40 x 46 27,5 0,09 2115 105 2115 205 2000 5 4,5 4,0 60 x 29 27,5 0,09 left drive 2115 303 2115 403 2000 5 4,5 4,0 40 x 46 27,5 0,09 2115 305 2115 405 2000 5 4,5 4,0 60 x 29 27,5 0,09 Hand speed counters Probator Rev speed in both directions Mechanical measuring with detachable contact points Display value memory, reset with knurled knob N < > 1/min / rpm Digits Digit height Mass Kg 2114 103 max. 6000 4 4,5 0,35 Hand tachometers universal Rev speed and surface speed in both directions Mechanical measuring with detachable contacts Eddy current principle with 3 measuring steps Display value memory, reset with push button N Step < > 1/min < > m/min GG Mass Kg I 40-500 4-50 2113 101 II 400-5000 40-500 ± 0,5 % 0,3 III 4000-50000 400-5000 E 95

Digital hand tachometers Digital hand tachometers Contact-free (optical) measurement with reflective tape, distance 350, Rev speed in both directions Mechanical measuring with detachable contact points, Rev speed, surface speed and length measurements in both directions Response time 0,5 sec ABS housing 2100 101 Digital hand tachometers optical Delivered in a box incl. reflective tapes and batterie Functions : Memory min., max., AV Auto OFF 2101 101 Digital hand tachometers optical and mechanical Delivered in a box incl. measuring points, measuring wheel 6, reflective tapes and batteries Functions : Memory min., max. AV Coutation rpm, m/min, ft/min, in/min, m/sec, ft/sec, m, ft, in Auto OFF 2100 210 10 pieces of reflective tapes 2100 215 Measuring points 2100 216 Hollow cone 2100 217 Measuring wheel 0,1 m 2100 218 Measuring wheel 6 2100 219 Measuring wheel 12 2100 220 Extension N < > Optical < > Mechanical Rotation Rotation Speed Length GG Mass kg 2100 101 1-99999 1/min / rpm - - - +/- 0,2% (1 Digit) 0,25 2101 101 1-99999 1/min / rpm 1-19999 1/min / rpm 0,1-1999 m/min 0,4-6550 ft/min 4-78700 in/min 0-99999 m 0-99999 ft 0-99999 in +/- 0,2% (1 Digit) 0,25 E 96

LED hand held stroboscope E LED hand held stroboscope for high precision applications Visualisation of vibrations and vibration behaviour - To keep track of material flow and production processes and of fast uniform movements that are not visible due to the high velocity - Contact-free measuring of rpm, repeat rate or frequency - Approx. 400lux at 6000fpm and 50 cm distance. No decrease in brightness with changes in the flash frequency - Large illuminated LCD display - 9x flash LEDs, replacement of illuminant not necessary - Precise strobe control through microprocessor - ABS housing for one-hand operation with central joystick - Delivered in box incl. rechargeable battery and charger 2103 101 fpm = Flashes per minute / fps = Flashes per second N < > < fpm Flash time 1/1000 sec. GG Mass kg 2103 101 1-2000 fps 60-120000 fpm 0,1<12000 1>12000 0,14-1000 +/- 0,001% 1,05 Hand held stroboscope Contact-free measuring of rpm, repeat rate or frequency To keep track of fast uniform movements that are not visible due to the high velocity Approx. 700 lux at 6000 fpm and 50 cm distance Large illuminated LCD display Xenon flash tube 10W ABS housing with rechargeable battery Delivered in box incl. rechargeable battery, charger and spare flash tube. 2105 101 Hand held stroboscope 2105 201 Spare rechargeable battery 2105 202 Spare flash tube fpm = Flashes per minute / fps = Flashes per second 2105 101 N < > fpm < fpm Flash time 1/1000 sec. GG Mass kg 2105 101 2105 101 40-12000 0,1 10-15 +/- 0,01% (+/- 0,5 fpm) 0,65 E 97

Precision crow stopper / Handtimer / Stopwatches 24609 Precision crow stopper / Handtimer / Stopwatches In ABS case ABS ø 55 Water-protected schock dust 24609 24607 24608 24607 Graduation S 1/5 1/10 1/100 Time min 30 15 30 24608 24610 Double stopper (hand timer) In steel case ø 55 Measuring of intermediate time Water-protected, schock, dust Graduation S 1/5 + 1/100 Time 30 24611 Digital stopwatches LCD display = 6 digits 1/100 - Battery SR44 Reading 59 min, 59,99 sec Functions : Start / stop / reset Measuring of intermediate time Date E 98

Hardness tester 29301 For determining Brinell hardness (Steel, bronze, aluminium, copper brass and cast iron) Delivered in a case, gauge box, magnifier, comparism table Digital hardness tester Reading 0,1 Maintenance-free hydraulic measuring system Test load selection by hand wheel Manual adjustment of test bench Delivered with protective covering and standard accessories Functions : ± Tolerance value input Indication when tolerance values overshoot Measured value conversion Data output RS232 Standard accessories Diamond cone 120, ball indenter 1/16 Hardness comparaison plate HRC and HRB, flat table ø 59 Table with V, hardness comparaison table and operating instructions 2144 701 Rockwell / Super Rockwell 2144 703 Rockwell / Brinell N Type Pre-load kgf Test load kgf < < < < < < Mass kg 2144 701 Rockwell Super Rockwell 3/10 15 / 30 / 45 60 / 100 / 150 220 145 720 x 520 x 280 82 2144 703 Rockwell Brinell 10 60 / 100 / 150 62,5 / 187,5 220 145 720 x 520 x 280 85 Shore hardness tester For determining the shore hardness in rubber and soft plastics Based on DIN 53505, ISO 7619, ISO 868, ASTM D2240 N Type < > < Mass kg 2146 501 Shore A 1-100 1 0,5 2146 502 Shore D 1-100 1 0,5 E 99

Scale Spring balances Model 15 Made from messing Length 292 Model Super Samson Made from plastic Length 262 Model 12 Made from plastic Length 215 SUPER Model 15 Model 15 SUPER Model 15 Capacity Model 12 Capacity Model 12 SAMSON (short) (long) SAMSON (short) 50 g x 1/2 g 10 kg x 50 g 100 g x 1 g 10 kg x 100 g 200 g x 2 g 10 kg x 200 g 500 g x 5 g 10 kg x 250g 1 kg x 5 g 12 kg x 250 g 1 kg x 10 g 15 kg x 100 g 1 1/2 kg x 25 g 20 kg x 100 g 2 kg x 10 g 20 kg x 200 g 3 kg x 50 g 25 kg x 500 g 5 kg x 25 g 40 kg x 500 g 5 kg x 100 g 50 kg x 500 g 6 kg x 100 g Model 15 (long) Suspended scales Model 235-6 Compact, robust, housed in the traditional metal case. Accurate to one part in 250 with up to 15% zero adjustment. Supplied with top and bottom hooks. Option : Round pan Galvanized scoop One hook simple or dubbel graduation With scales Round plate in stainless steel 310 ø with chain dual marked Capacity Capacity Capacity 5 kg x 20 g 5 kg x 20 g 5 kg x 20 g (11lb x loz) 5 kg x 20 g (11lb x 1oz) 10 kg x 50 g 10 kg x 50 g 10 kg x 50 g (22lb x 2oz) 10 kg x 50 g (22lb x 2oz) 25 kg x 100 g 25 kg x 100 g 25 kg x 100 g 25 kg x 100 g (56lb x 4oz) 24 L x 0,2 ltr 25 kg x 100 g (56lb x 4oz) 50 kg x 200 g 50 kg x 200 g (110lb x 8oz) 100 kg x 500 g 100 kg x 500 g (220lb x 1lb) Suspended scales type CH (hanging scale) Multi data hold function - Batteries 9V Capacity kg 15 50 50 Reading 20 50 100 E 100

Scales Crane scale Digital IP 65 - Radio transmission 150 kg x 0,02 kg 6500 kg x 1 kg tested tested 300 kg x 0,05 kg 9500 kg x 2 kg 150 kg x 0,05 kg 3000 kg x 1 kg 600 kg x 0,1 kg 12000 kg x 2 kg 300 kg x 0,1 kg 6000 kg x 2 kg 1500 kg x 0,2 kg 25000 kg x 5 kg 600 kg x 0,2 kg 6000/9500 kg x 2/5 kg 3000 kg x 0,5 kg 35000 kg x 10 kg 1500 kg x 0,5 kg Pocket scale Capacity 1 kg - Reading 1 g Dimensions 85 x 130 x 25 2 batteries AAA, 1,5V Digital normal scale Capacity 2200 gr 2200 gr 5200 gr Reading 0,1 g 1 g 5 g 2 batteries AA (1,5V) Functions auto-off Add on weighing Dimensions 170 x 240 x 38 Multi-functions scales For laboratory, counting, control IP54 Deduction for container weighing Uitgang RS232 Capacity g 1210 12100 16100 Reading g 0,01 0,1 0,2 Stainless steel plate ø 150 200 x 160 200 x 160 Piece minimum load 0,039 0,39 0,69 Parcel balance for dispatch weighing IP54 Capacity 6 kg 35 kg 60 kg 150 kg 300 kg Reading 5 g 20 g 50 g 100 g 100 g Dimensions 310 x 300 x 55 310 x 300 x 55 550 x 550 x 65 945 x 505 x 65 945 x 505 x 65 6 batteries AA (1,5V) Function auto OFF Cable 1,8 m E 101

Universal testing and measurement TESTERS Non-contact voltage tester VT 25 70-250 V AC L/N detection Continuity Flashlight function Self-test Two sensibility levels Buzzer Safety : 250 V, Cat. II (IEC 61010)- CE approved Length / Weight : 132 / 25 g Supplied with 2 x 1.5 V button cells Stud detector (wood/metal) and energized conductors D 45 No longer blindly drill into your wood or sheetrock walls Detection of energized conductors Detect metallic objects (pipes...) and the position of wood or metal studs Detection depth : 30 cm Accuracy : ± 15 Automatic calibration Auto OFF Supplied with 12 V battery type MN21 Dimensions () / Weight : 130 x 65 x 35 / 130 g Socket and RCD/ELCB tester 10mA and 30mA VT 35 Simply plug in and watch indicators! Fast wiring test for European and British format sockets (Earth/ Ground, Phase and neutral wiring) Rapid testing for differential circuit-breaker triggers 30 ma Self-powered by the mains Safety : 250 V Cat. II (IEC 61010)-CE Dimensions () / Weight : 85 x 56 x 31 / 250 g Battery tester VT 31 One tester for all batteries! 1,5 V button cell battery (mercury, silver oxide or alkaline) Lithium 3 V AAA / R3, 1,5 V (alkaline or rechargeable) AA / R6 / C / D, 1,5 V (alkaline or rechargeable) Camera batteries 6 V 12 V, 15 V, 22,5 V batteries Self-powered by the tested battery Dimensions () / Weight : 85 x 56 x 31 / 88 g Supplied with interdependent red and black leads E 102

Sound level meter and thermometer E Analog sound level meter SL 101 Easy to use Large display 7 ranges : 50 db to 126 db Reads both A and C frequency massings according to IEC standards Fast or slow response integration time Low battery check Tripod mount Dimensions () / Weight : 175 x 64 x 40 / 210 g Supplied with 1 x 9 V battery Digital sound level meter SL 105 Easy to use Large backlit screen Sound intensity measurements in all acoustic environments : noisy/quiet, high/low pitch, wide-band, intermittent or continuous. Measures from 30 to 130 db with automatic selection of measurement range Compliancy with standard IEC 651 A and C frequency weighting Choice of slow/short integration times Resolution : 0,1dB Accuracy : +/- 1,5 db Dimensions / Weight : 200 x 55 x 38 / 170 g Supplied with 1 x 9V battery, carrying case and wind sheet Infrared distance thermometer TM 65 Distance to target factor : 6/1 Emissivity : 0,95 Measurement range : -20 C to + 270 C Resolution : 1 C Accuracy : ± 2,5% +2 C Laser targeting MAX Auto-Hold Choice of measurement unit Dimensions () / Weight : 94 x 51 x 25 x 76 g Supplied with 1 battery and 1 wrist strap Digital lightmeter LM 76 Display 2000 counts Measurement range : 0 to 200 000 Lux 4 ranges Accuracy : 3% Remote-controlled probe Incidence correction Max, Min, Hold Measurement units : Lux or Fc Dimensions () : unit - 130 x 55 x 38, probe - 125 x 86 x 35 Weight : 250 g Supplied with 1 carrying bag 28737211 Thermometers by contact TM 60 TM 62 Kind of input Thermocouple K / J Thermocouple K / J Number of inputs 1 2 Display Single Dual Measurement range Resolution Accuracy -200 C to +1370 C 0,1 C ± 0,05 % + 0,7 C Functions Relative measurement MAX, MIN, HOLD T1-T2 temperature - yes Backlight yes Choice of temperature unit yes Dimensions /Weight 130 x 56 x 38 / 170 g 130 x 56 x 38 / 170 g To order 1K thermocouple sensor 2K thermocouple sensors 1 battery and 1 carrying bag E 103

Digital multimeters 28737209 DMM 105 DMM 110 DMM 120 DMM 140 Display 2000 counts 2000 counts 4000 counts 4000 counts Ranges Manual Manual and automatic I DC I AC V DC V AC Resistance Continuity (with buzzer) Range 200 µa / 2000 µa / 20 ma / 200 ma / 10A 200 µa / 2000 µa / 20mA / 200 ma / 2A / 10A Basic accuracy 1 % 1,2 % Best resolution 0,1 µa 0,1 µa Range 200 µa / 2000 µa / 20mA / 200 ma / 2A / 10A Basic accuracy - 1,5 % Best resolution 0,1 µa Range 200 mv / 2 V / 20 V / 200 V / 1000 V 200 mv / 2 V / 20 V / 200 V / 600 V 400 µa / 4000 µa / 40 ma / 400 ma / 4 A / 10A 400 µa / 4000 µa / 40 ma / 400 ma / 4 A / 10A 400 mv / 4 V / 40 V / 400 V / 600 V Basic accuracy 0,8 % 0,5 % Best resolution 0,1 mv 0,1 mv Range 200 V / 750 V 200 mv / 2 V / 20 V / 200 V / 600 V 400 mv / 4 V / 40 V / 400 V / 600 V Basic accuracy 1,2 % 1% Best resolution 0,1 V 0,1 mv Range 200 Ω / 2 kω/ 20 kω / 200 kω / 2MΩ 200 Ω / 2 kω/ 20 kω / 200 kω / 2 MΩ / 20 MΩ Basic accuracy 1 % 1 % Best resolution 0,1 Ω 0,1 Ω Seuil - 100 Ω Protection 250 V RMS 500 V RMS 400 Ω / 4 kω/ 40 kω / 400 kω / 4 MΩ / 40 MΩ Frequency 40 Hz / 400 Hz / 4 khz / Range 40 khz / 400 khz / 4 MHz - - - Basic accuracy 0,2 % Best resolution 0,01 Hz Capacity - - - 40 nf / 400 nf / 4 µf / 40 µf / 100 µf Diode test yes yes yes yes Other features Battery test 1,5 V (AA) and 9 V (6F22) DATA HOLD Auto power off, Protection by fuses Backlight, DATA HOLD Auto power off, Protection by fuses Power supply 1 x 9V 6F22 2 x 1,5V AA 2 x 1,5V AA Dimensions ()/Weight 145 x 73 x 40 / 500 g 152 x 78 x 35 / 280 g 152 x 78 x 35 / 280 g Safety 600 V Cat. II / 300 V Cat. III 600 V Cat. II / 300 V Cat. III 600 V Cat. II / 300 V Cat. III Supplied with 1 sheath, 1 set of red/ black test probe leads and 9V battery 1 sheath, 1 set of red/ black test probe leads and 2 batteries 1 sheath, 1 set of red/black test probe leads and 2 AA 1.5 batteries Carrying bag and storage fittings for pocket multimeters ACC N 20 Padded and light-weight Velcro fastening Carrier for attaching to belt and ring Compartment for storing measurement leads Diode tests and continuity tests Perfectly adapted to fitt the DMM 110, 120, 140 and the X 1000. E 104

Clamp-on multimeters E 100 A to 600 A pocket clamp-on multimeteres, Ø 30 Auto-ranging CM 600 CM 605 CM 610 28737208 CM 600 CM 610 CM 625 CM 605 Clamping ø 30 30 30 12,5 Display 2000 counts 2000 counts 4300 counts 10 000 counts Range 40 A / 400 A 10 A / 80 A / 100 A I DC Basic accuracy - - 1,5 % 2,5 % Best resolution 0,01 A 1 ma Range 200 A / 600 A 200 A / 600 A 40 A / 400 A 10 A / 80 A / 100 A I AC Basic accuracy 1,9 % 1,9 % 1,5 % 2 % Best resolution 0,1 A 0,1 A 0,01 A 1 ma V DC V AC Resistance Range 200 mv / 2 V / 20 V / 200 V / 600 V 200 mv / 2 V / 20 V / 200 V / 600 V 4 V / 40 V / 400 V / 600 V 600 V RMS Basic accuracy 0,7 % 0,7 % 0,75 % 1 % Best resolution 0,1 mv 0,1 mv 0,001 V 0,1 V Range 2 V / 20 V / 200 V / 600 V 2 V / 20 V / 200 V / 600 V 4 V / 40 V / 400 V / 600 V 600 V RMS Basic accuracy 1,5 % 1,5% 1 % 1,5 % Best resolution 0,001 V 0,001 V 0,001 V 0,1 V Range 200 Ω / 2 kω/ 20 kω / 200 kω / 2 MΩ / 20 MΩ 200 Ω / 2 kω/ 20 kω / 200 kω / 2 MΩ / 20 MΩ 400 Ω / 4 kω/ 40 kω / 400 kω / 4 MΩ / 40 MΩ Basic accuracy 1,5 % 1,5 % 0,9 % 1 % Best resolution 0,1 Ω 0,1 Ω 0,1 Ω 1 Ω Continuity R < 60 Ω 60 Ω 50 Ω 50 Ω Protection 600 V RMS 600 V RMS 600 V RMS 600 V RMS Diode test yes yes - - Auto zero - - yes yes Special features MAX MAX HOLD Analog output 10 mv / A AC or DC 4,5% + 0,5 mv / 20 khz to ± 3 db / Z = 3 kω HOLD / PEAK Power supply 2 x 1,5 V AAA 2 x 1,5 V AAA 2 x 1,5 V AAA 2 x 1,5 V AAA Dimensions () / Weight 189 x 71 x 37 / 200 g 189 x 71 x 37 / 200 g 189 x 71 x 37 / 220 g 202 x 70 x 34 / 180 g Safety Supplied with 600 V Cat. II / 300 V, Cat. III (IEC 61010) - CE 600 V Cat. II (IEC 61010) - CE 1 carrying bag, 1 set of red/black test probe leads and 2 batteries 10 kω 600 V Cat. II - 300 V, Cat. III (IEC 61010) - CE E 105

Clamp-on multimeters 1000 A clamp-on multimeters, temperature function, ø 40 Automatic or manual ranging CM 660 CM 670 CM 685 Clamping ø 40 40 40 Display 4300 counts 4300 counts 4300 counts Range 40 A / 400 A / 1000 A I DC Basic accuracy - - 1 % Best resolution 0,01 A Range 40 A / 400 A / 1000 A 40 A / 400 A / 1000 A 40 A / 400 A / 1000 A I AC Basic accuracy 1 % 1 % 1 % Best resolution 0,01 A 0,01 A 0,01 A Range 4 V / 40 V / 400 V / 600 V 4 V / 40 V / 400 V / 600 V 4 V / 40 V / 400 V / 600 V V DC Basic accuracy 0,75 % 0,75 % 0,75 % Best resolution 0,001 V 0,001 V 0,001 V Range 4 V / 40 V / 400 V / 600 V 4 V / 40 V / 400 V / 600 V 4 V / 40 V / 400 V / 600 V V AC Basic accuracy 1 % 1 % 1 % Best resolution 0,001 V 0,001 V 0,001 V Resistance Range 400 Ω / 4 kω/ 40 kω / 400 kω / 4 MΩ / 40 MΩ 400 Ω / 4 kω/ 40 kω / 400 kω / 4 MΩ / 40 MΩ 400 Ω / 4 kω/ 40 kω / 400 kω / 4 MΩ / 40 MΩ Basic accuracy 0,9 % 0,9 % 0,9 % Best resolution 0,1 Ω 0,1 Ω 0,1 Ω Continuity R < 50 Ω 50 Ω 50 Ω Protection 600 V RMS 600 V RMS 600 V RMS Range 400 Hz / 4000 Hz 400 Hz / 4000 Hz 400 Hz / 4000 Hz Frequency Basic accuracy 0,5 % 0,5 % 0,5 % Best resolution 0,1 Hz 0,1 Hz 0,1 Hz Temperature de - 50 C to + 1100 C de - 50 C to + 1100 C de - 50 C to + 1100 C Speacial features MIN / MAX, HOLD, PEAK MIN / MAX, HOLD, PEAK MIN / MAX, HOLD, PEAK Power supply 2 x 1,5 V AA 2 x 1,5 V AA 2 x 1,5 V AA Dimensions () / mass 241 x 91 x 45 / 390 g 241 x 91 x 45 / 390 g 241 x 91 x 45 / 390 g Safety Safety : 600 V Cat. III (IEC 61010)-CE Supplied with 1 carrying bag, 1 set of red/black test probe leads and 2 batteries Adapter and K sensor temperature probe ACC N 80 For CM 660, CM 670 and CM 685 clamp-on multimeters - Measurement range : -50 C to +1800 C - Resolution : 0.1 C to 2 C Carrying case ACC N 21 Contains two expandable compartments (100 and 35 ) and a compartment for documents. Ideal for clamp-on models CM 660, CM 670 and CM 685. Supplied with a carrying strap (17 cm) and a shoulder strap (50 cm). Dimensions () : 250 x 165 x 60 E 106

Selection guide E F03-0381 F01 F03 F09 F15 Clamping diameter 26 42 Display 4000 pts Backlighting yes AC/DC auto selection yes Current AC 0,5 to 400-1000 A 0,20 to 40-400 - 600 A DC 0,2 to 400-1400 A Continuity (buzzer) R<40 Ω ajustable R < 40 Ω Semi-conductor test yes Power measurement (single-phase) with power factor 5 to 240 k (W, var, VA) Phase rotation order Temperature yes Electrical safety IEC 61010-1, 600 V cat. III Valeur efficace vraie [AC] [AC], DC [AC+DC] [AC], DC [AC], DC AC/DC auto selection AC Voltage AC and DC Power single-phase - 3 phase (W, VA, var, FP) Phase rotation Temperature Frequency Engine starter (InRush) Existence of dangerous tension (V-live) Min / Max 100 ms Peak 500 µs F03-0393 F15-S F15-S1 Digital insulation testers Voltage Insulation range Continuity Resistance Capacity AC/DC current Alarms Chronometer Relative measurement Display Backlighting Power supply Electrical safety C.A 6523 C.A 6525 0 to 600 VAC/DC 500 / 1000 VDC 100 kω to 2 GΩ -20 Ω to 20 Ω yes LCD + bargraph yes 6 x 1,5 V batteries IEC 1010 Cat.II 300 V 250 / 500 / 1000 VDC 50 kω to 2 GΩ 0 to 15 min E 107

Installation testers C.A 6115-FT Installation testers C.A 6114 C.A 6115N Voltage measurement 10 to 440 VAC / DC upon connection Frequency measurement 15,3 to 450 Hz upon connection Insulation Method Bipolar Bipolar + automatic L-N-PE U test 100 / 250 / 500 V R 5 kω to 600 MΩ Differentials test 10 / 30 / 100 / 300 / 500 ma I N + variable between 6 ma and 1000 ma Trips failure test 1/2 I N Tripping time I N, 2 x I N, 5 x I N, 150 ma, 250 ma + step mode Tripping current step mode Earth method 1P : 0,15 Ω to 10 kω Selective earth with current clamp (optional) Loops (without diff. trip 30 ma Loops L-PE, L-N and L-L Impedance and resistance : 0,08 to 200 Ω Selective L-PE loop with current clamp (optional) Continuity 0,16 Ω to 2 kω at 200 ma (audible beep) Phase rotation si 20 VAC < voltage present < 440 VAC Current / leakage current with current clamp (optional) Alarms in each function Memory 800 measurements RS 232 yes Power supply NiMH battery with built-in charger Electrical safety IEC 61010-1 Cat. III 300 V C.A 6115-SM C.A 6115-SN Voltage measurement Frequency measurement Differentials test I N Trips failure test Tripping time Tripping current Earth Selective earth Loops (without diff. trip 30 ma Calcul courant de court-circuit Selective L-PE loop Phase rotation Current/leakage current Alarms memory Counication output Power supply Electrical safety C.A 6454 C.A 6456 C.A 6030 de 2 to 550 V AC/DC upon connection de 15,3 to 450 Hz upon connection 10 / 30 / 100 / 300 / 500 ma + variable betwen 6 ma and 650 ma 1/2 I N 1/2 I N, I N, 2 x I N, 5 x I N, 150 ma, 250 ma + step mode step mode + method 3P / 2P with current clamp (optional) L-PE / L-N / L-L L-PE impedance and resistance : 0,20 Ω to 4000 Ω par calcul ik = Uref / Z L-PE with current clamp (optional) If 90 VAC < U < 550 VAC with current clamp (optional) in each function 100 measurements Optial interface 6 x 1,5 V batteries IEC 61010-1 Cat. III 600 V E 108

Analogue and digital multimeters E CA5003 Analogue and digital multimeters C.A 5001 C.A 5003 C.A 5011 Voltage DC 8 cal. : 100 mv to 1000 V Dig. 5 cal. : 400 mv to 1000 V AC 5 cal. : 10 V to 1000 V Ana. 5 cal. : 500 mv to 1000 V Current DC 5 cal. : 50 µa to 5 A 7 cal. : 50 µa to 15 A Dig. 6 cal. : 400 µa to 10 A AC 4 cal. : 50 ma to 5 A 5 cal. : 1,5 ma to 15 A Ana. 5 cal. : 500 µa to 10 A Resistance 2 ranges : 10 k and 1 M Dig. 6 cal. : 400 Ω to 40 MΩ Ana. 6 cal. : 500 Ω to 50 MΩ Audible continuity test R < 50 Ω R < 400 Ω Frequency measurement Dig. : 3 cal : 4 khz to 400 khz Electrical safety IEC 61010-1 600V / Cat. III pol. 2 IEC 61010-1 1000V / Cat. III CA5001 CA5011 Multimeters DMM 210 DMM 220 DMM 230 DMM 240 Display 6000 points - Backlight with bargraph 40000 pts-backlight with bargraph Bandwidth 40 Hz to 1 khz 50 Hz to 1 khz Range 600 µa / 6000 µa / 60 ma / 600 ma / 6 A / 10 A 400 µa / 4000 µa / 40 ma / 400 ma / 10 A (20 A max.) I DC Basic accuracy 1,0 % + 3 pts Best resolution 0,1 µa 0,01 µa 4-20 ma - 0 to 125 % Range 600 µa / 6000 µa / 60 / 6 A / 10 A (20 A max.) ma / 600 ma 400 µa / 4000 µa / / 10 A (20 A max.) 40 ma / 400 ma I AC Basic accuracy 1,5 % + 3 pts Best resolution 0,1 µa Range 600 mv / 6 V / 600 V / 1000 V 400 mv / 4 V / 40 V / 400 V / 1000 V V DC Basic accuracy 0,09 % + 2 pts 0,06 % + 2 pts Best resolution 0,1 mv 0,01 mv Range 6 V / 60 V / 600 V / 1000 V 400 mv / 4 V / 40 V / 400 V / 1000 V V AC Basic accuracy 1,0 % + 3 pts Best resolution 1 mv 0,1 mv Range 600 Ω / 6 kω / 60 kω / 600 kω / 6 MΩ / 60 MΩ 400 Ω / 4 kω / 40 kω / 400 kω / 4 MΩ / 40 MΩ Resistance Basic accuracy ± 0,3 % R + 4 pts Best resolution 0,1 Ω 0,01 Ω Audible continuity test yes / 0,1 Ω Diode test yes Capacity - 0,01 nf to 1000 µf 0,001 nf to 40 mf Temperature (thermocouple type K) - -45 C to + 750 C -50 C to +1000 C Frequency electric 10,00 to 400,00 Hz 40,00 to 400,00 Hz electronic 0,001 Hz to 10,00 MHz 0,001 Hz to 100,00 MHz Cycle 0,1 to 99,99 % Selection range Autorange / Manual Other features Peak value Relative mode - MIN, MAX Protection IP 67 Safety 600 V Cat. IV / 1000 V Cat. III selon IEC 61010 Dimensions / Weight 187 x 81 x 50 / 342 g env. State of delivery Battery, test leads with touch points K type Peak value Relative mode - MIN, MAX, PEAK (1 ms) Battery, test leads with touch points + adaptor for couple K + temperature drill K type DMM 210 DMM 220 DMM 230 E 109

Infrared thermometer 845 Infrared thermometer First Far distances : the Testo 845 is equipped with 75:1 optics for measurements at distance. The thermometer marks the object to be measured with a laser cross to ensure that the actual position and diameter of the measurement point are identifiable during the measurement. Close focus : the Testo 845 features a 2 point laser to mark the measurement point exactly. At very close range the instrument can take accurate measurements of very small objects at a distance of 70 the Testo 845 measures a spot of just 1 diameter. In addition the Testo 845 offers a host of useful features - Broad measuring range - from -35 to +950 C - Reference class accuracy, up to ± 0.75 C - Online measurement & Documentation via USB and Testo software - Ultra fast measurement rate, scanning 100 ms - Onsite printing to an optional infrared printer - Input for thermocouple probes for contact temperature measurements - The degree of emission is freely adjustable from 0,1 to 01,0 - Simple operation and a clear backlit display showing measured temperature, minimum / maximum values (freely selectable) the degree of emission. Capacity C - 35 to + 950 Resolution C 0,1 Optic resolution Distant field : 75 : 1 (16, distance 1200 ) close field (point net) : 1, distance 70 Adjustable emission 0,10 to 1,00 Dimensions (L x l x H) 155 x 58 x 195 Mass g 465 For the measure of surrounding humidity and the determination of the distance of the point of dew. To connect up on the thermometer 496110. 0 to 100 % rf Capacity -20 to + 50 C ± 2 % rf (2 to 98 % rf) Accuracy ± 0,5 C (0 to 50 C) Resolution 0,1 % rf 28737 Testers 3,5-400 V C.A 745 C.A 760 C.A 704 Display 9 LED 10 LED LCD 2000 counts with backlighting Voltage test 690 V 690 V 690 V Polarity test yes yes yes Phase position yes yes yes Resistance measurement 2000 Ω Voltage absence tester yes yes Continuity with buzzer yes yes Phase rotation yes yes Socket test yes yes Autotest yes yes yes Electrical safety 600 V cat. III 600 V cat. III and IEC 61243-3 cl. B E 110

arth and resistivity testers E Earth and resistivity testers C.A 6460 C.A 6462 C.A 6470 Measurement Earth / resistivity / coupling Earth / resistivity / coupling / continuity Range 0,01 to 2000 Ω (3 automatic ranges) 0,001 Ω to 100 kω (automatic ranges) Methods 4 rods/3rods (terminal bar between E&ES) 4P / 3P / 2P Frequency 128 Hz 41 Hz to 512 Hz Voltage circuit (E-S) LED if noise > 13 V peak RS, RE Measurement Current circuit (E-H) LED if R > 50 kω RH, RE Measurement Voltage circuit resistance (E-S) LED if R > 50 kω Uparasite Measurement Power supply 8x1,5 V batteries rechargeable NiMH battery Electrical safety En 61010 and IEC 61557 EN 61326-1 / EN 61010-1 and IEC 61557-1-4-5 Display LCD digital 2000 counts LCD with 3 digital display Backlighting yes Dimensions 270 x 250 x 110 260 x 240 x 120 Weight 2,8 kg 3,3 kg 2,7 kg Stae of delivery With batteries, 1 instruction manual in 5 languages With power supply lead, 1 instruction manual in 5 languages With external charger, recharging cable for mains plug, data transfer software, 1 optical counication cable, 1 instruction manual in 5 languages, 5 plastic covered, simplified instruction manuals. C.A 6462 3 in 1 : earth, resistivity, coupling - Site-adapted casing - Rechargeable NiMH battery Non-contact thermometers C.A 871 C.A 879 C.A 881 C.A 882 D/S targeting range 8/1 12/1 30/1 50/1 Emissivity 0,95 0,95 0,2 to 1 Measurement range -40 to +538 C -50 to +550 C -32 to +600 C -32 to +900 C Resolution 0,1 C up to 100 C 1 C beyond that 0,1 C 0,1 C Accuracy ± 2,5% ± 2 C ± 1,5% ± 2 C 2% + 1 pt ± 1% Functions Laser sighting yes yes yes yes Continuous measurement yes Audible alarms Max. value yes Min. value yes Average yes Auto-hold yes Choice of measurement unit C or F Display 2000 counts Backlighting yes Dimensions 160 x 82 x 41,5 230 x 100 x 56 250 x 100 x 45 Weight 180 g 290 g 320 g State of delivery Delivered with 1x9V battery; carrying case. Delivered with 1x9V battery, carrying case and instructions Delivered with 1x9V battery, with wrist strap and carrying case. Gas detectror C.A 895 Referency > P01.6510.01Z Audible alarm progressively beginning at 50 ppm Measurement range 0 to 1000 ppm Max. value yes Resolution 1 ppm Hold yes Accuracy ± 5% + 5 ppm Display 2000 counts Measurement mode Backlighting yes normal for CO detection Dimensions 237 x 60,5 x 38 Average for precise measurements Weight 190 g Functions State of delivery 1 protective shockproof sheath C.A 895 Tests the good working order of combustion equipment - Audible signal warns of possible risk - 2 measurement modes :: normal or average E 111

Bearing checker T2024698 Bearing checker Bearing Checker Bearing Checker is a portable instrument for fast and easy measurement of bearing condition in preventive maintenance. The instrument is push button controlled and basic measurement data are entered manually. Bearing Checker measures shock pulses with a built-in probe and machine surface temperature with infrared light. The instrument can also be used as an electronic stethoscope for detecting machine sound irregularities. Technical data Casing / cover : ABS/PC, IP54 Shock pulse measurement Size : 158 x 62 x 30 Measurement technique : dbm/dbc, measuring range (6.2 x 2.4 x 1.2 in) -9 to 90 dbsv, ±3 dbsv Weight : 185 g (6.5 ounces) including batteries Transducer type : Built-in probe transducer Keypad : Sealed membrane (silicone rubber) Display : Bearing condition indication : Measurement indication : Graphic monochrome, 64 x 128 pixels, LED backlight Green, yellow and red light diodes Blue light diode temperature measurement Temperature range : -10 C to +160 C (14 F to 320 F) Resolution : 1 C (1 F) Transducer type : Thermopile Sensor TPS 334/3161, built-in contact free IR-sensor Power supply : 2 batteries 1,5 V AA, alcaline or rechargeable Stethoscope Earphone mode : 8 level amplification battery life : 20 hours of normal use Operating temperature : Input connector : Output connector : General functions : 0 C to +50 C (32 F to 122 F) Lemo coaxial, for external shock pulse transducers (probe or quick connector) 3,5 stereo mini plug for headphones Battery status display, transducer line test, metric or Imperial units of measurement, language independent menus with symbols, storage of up to 10 measurement values. Article numbers BC100 EAR12 TRA73 TRA74 CAB52 15286 15287 15288 93363 93062 Bearing Checker, excl. batteries Headphones with eardefenders External transducer with probe Transducer with quick connector for adapters Measurng cable, 1,5 m, Lemo - BNC slip-on Belt holder for external probe transducer Belt case for accesories Protective cover with wrist strap Cable adapter, Lemo - BNC Cable adapter, BNC - TNC plug-jack E 112

Sheave/Pulley Alignment E Sheave/Pulley Alignment Easy-Laser BTA compact TM is the perfect tool for sheave and pulley alignment. Mounted in a few seconds, the laser line projected onto the targets allows you to quickly ascertain and correct the misalignment. It couldn t be easier! 4Shows the parallel and angular misalignment between the sheaves. 4Much faster and more accurate than measuring with earlier, conventional methods. 4For both horizontal and vertical mounted machines. 4Alignment can be made by one operator. 4Also suitable for non-magnetic sheaves. Compact, light weight unit fits almost any kinds of sheaves. Parallel and angular misalignment Parallel misalignment Angular misalignement V-BELTS TIMING BELTS FLAT BELTS CHAIN DRIVES E 113

The V-shaped targets shows the slightest move of the laser line as it changes in length when moved. Maintenance means savings In the industry of today, preventive and predictive maintenance is a matter of course. When aligning with Easy-Laser BTA compact TM you reduce the wear on sheaves, belts, bearings and sealings and reduce vibrations. This will give you less downtime, which of course means that you increase the available machine time. Time that guarantees your income. Increased efficiency also means large energy cost savings. Easy for the user The tool is attached in a few seconds, and you can easily see the laser line projected on the targets. When the line lies in the slots of the targets, the machine is in the right position. The result is a fast, precise alignment. Misaligned Aligned Horizontal alignment Vertical alignment The alignment can be done with 3 or as on the picture, 2 targets. When measuring sheaves mounted similar to pictures, use measuring tape of ruler instead of targets. Technical specifications Complete tool : Part 12-0105 Laser transmitter Sheave diameters : ø 60-1500 Measurement distance : 15 m Power supply : 1 battery R6 (AA) - 1.5 V Battery operation : 4 hours continuously Laser class : 2 Protection : IP65 Output power : < 1mW Laser wavelength 635-670 nm Housing material : ABS platics Dimensions : 300 x 60 x 25 Weight : 1 kg Targets 3 pcs. magnet targets Calibration The laserline generated by the tool is calibrated parallel to the two attachment magnets. Can also easily be done in the field when necessary. Measurement accuracy Accuracy : Better than 0.5 or 0.2 * Leatherette with belt clip included. E 114 The adjustable arm and moveable magnets allows the BTA to be attached to a varying sheave and sprocket diameters and designs.

Alignment system for rotating machinery E A complete measurement system Easy-Laser Extreme TM is a measurement and alignment system for rotating machinery such as motors and pumps, turbines, compressors, gearboxes, blowers, etc. In addition to shaft alignment programs, there are also programs for measuring straightness and twisting of foundations, for example. This means that the system is extremely suitable both for the establishment of new installations and for continuous maintenance work. Measurement programs and functions The key to quick and easy measurements is a measurement program that helps you achieve your best. We have therefore included a large number of measurement programs in the display unit as standard. All measurement programs guide the user through the entire measurement process step by step. So you can leave most of the thinking and all the difficult calculations to the measurement system. EASYTURN TM - For alignment of horizontal machines. Allows complete measurement with only 40 rotation of the shafts. HORIZONTAL - For alignment of horizontal machines in accordance with the 9-12-3 method. SOFT FOOT - With this program you can check that the machine is resting on all feet. Shows which foot should be corrected. Thermal growth compensation - Compensates for difference in thermal expansion between the machines. Sub-function. Tolerance check - Checks the readings for offset and angle against the selected tolerance. Graphic representation on the screen when the alignment is wihin the tolerance values. Sub-function. Measurement value filter - Advanced electronic filter function for a reliable measurement result even in a poor measurement environment, e.g. where there is air turbulence or high vibration. Sub-function. CARDAN - Shows angular errors and adjustment value on cardan-shaft-coupled/centre-offset machines. (Requires accessory fixtures.) VERTICAL - For measurement of vertical and flange-mounted machines. Machine train - For the alignment of two to ten machines in a row (nine couplings). The entire alignment process can be followed live on the screen. REFLOCK TM - Any pair of feet can be locked/set as a reference. This is a subfunction in the Machine train program. Offset and angle - Shows centre offset and angular error between, for example, two shafts. Also suitable for dynamic measurements. Values - Shows live readings from S and M unit. Can be used for shaft alignment, straightness measurement and dynamic measurement. Straightness - For measuring straightness of machine foundations, shafts, bearing journals, etc. Can handle up to 150 measurement points with two zero points. DOCUMENTATION OF MEASUREMENT RESULTS Once measurements are complete, you have several options for documenting the results. Choose the one that is most suitable for the situation, depending, for example, on whether further analysis is needed or whether a measurement report must be produced. The keyboard with all characters accessible makes it simple to give each measurement a unique description. Your description SAVE IN THE DISPLAY UNIT You give each measurement a unique description. The system then adds the time and date of the measurement. Up to 1,000 shaft alignments can be saved. PRINTOUT If you want to document the alignment without using a PC, just connect up a printer and print out all measurement data. (A printer is an accessory and is not approved for explosive environments.) Printout of all measurement data TRANSFER MEASUREMENT DATA TO PC With the EasyLink TM program for Windows (included), you can produce professional reports using both measurement data and pictures and export to spreadsheets such as Excel, etc. Connection is via RS232 or USB. Excel sheet with pictures E 115