Contents Basic Series 17-31 Section 1 Basic & Specialty Specialty 32x18 Frame 45-46 & End Caps 30 Series 32-35 Door Rolling Door Guide 47 Sliding Door Guide 48 28 Series 36- Panel Stiffener/Handle 49 Panel Mounting 49 20 Series 41-43 Clamp Mesh Clamp 50 Clamp Bar 50 End Caps 56-57 Rack Angle 51 UHMW 52 Profile Covers 53 Panel/Mesh Gaskets 54 Cover Strips 55 Conduit 59-63 Conduit Accessories 64 13 Parker Hannifin Corporation Business Unit
Overview 20 Series 12-081 12-120 28 Series 12-020 12-124 12-0 12-126 12-125 12-028 12-128 12-228 12-328 12-044 12-043 12-428 12-528 12-628 30 Series 12-728 12-056 12-030 12-034 12-035 12-033 12-060 12-066 Series 10-016 10-5 10-0 11-0 10-3 10-1 10-2 10-4 11-5 10-043 10-044 11-044 10-045 10-060 10-081 10-083 10-085 10-086 10-089 10-680 10-080 10-180 11-080 14-248 11-100 14 Parker Hannifin Corporation Business Unit
Overview Series & End Caps 10-088 11-088 11-089 10-120 11-120 10-161 11-128 10-164 11-1 11-084 11-124 11-122 10-160 11-160 Specialty 12-031 12-032 11-056 10-036 15 Parker Hannifin Corporation Business Unit
Overview Roller Systems 13-505 13-513 13-524 13-106 13-114 13-125 13-700 Conduit 15-0 15-080 15-162 15-120 15-160 15-041 15-081 15-121 15-085 15-161 15-083 15-122 15-082 15-042 Door 12-012 12-014 12-011 12-013 12-015 12-018 12-022 T-Slot Covers 12-101 12-102 12-104 12-106 12-107 12-108 12-111 12-112 12-115 12-116 12-113 12-114 Slides 12-410 12-421 12-430 12-420 13-410 13-4 13-810, 13-800 12-0 13-430 13-450 Panel 12-105 12-010 12-109 12-110 16 Parker Hannifin Corporation Business Unit
Series Series Moment of Inertia Section Modulus I X I Y W X W Y Section Weight Cat. Part # Description [cm4 ] [cm4 ] [cm3 ] [cm3 ] [cm 2 ] [kg/m] Page 10-016 Profile 16x 6.97 1.06 3.49 1.23 4.33 1.17 24 10-036 Profile Post 36x36 8.55 8.55 4.32 4.32 7.18 1.94 31 10-0 Profile x Standard 9.46 9.46 4.73 4.73 6.65 1.72 19 10-043 Profile x Quarter Round ST 6.85 6.85 3.12 3.12 5.86 1.58 21 10-044 Profile x-45 Standard 6.71 6.71 2.98 2.98 5.68 1.53 22 10-045 Profile x45 Standard 16.27 34.39 7.43 9.62 10.22 2.76 22 10-060 Profile x60 Standard 12.73 42.73 6.08 10.93 9.35 2.76 22 10-080 Profile 80x Standard 71.79 17.23 17.99 8.62 11.53 3.18 26 10-081 Profile 16x80 50.76 2.15 12.69 2.69 8.13 2.20 24 10-083 Profile Rx80 30 Standard 6.09 8.48 2.67 3.59 5.79 1.57 23 10-085 Profile Rx80 45 Standard 16.26 11.85 5.06 4.59 7.09 1.92 23 10-086 Profile Rx80 60 Standard 30. 19.27 7.94 6. 8.30 2.25 23 10-088 Profile 80x80 Standard 138.30 138.30 34.58 34.58 20.17 5.45 27 10-089 Profile Rx80 90 Standard 66.03 66.03 16.14 16.14 12.69 3.44 23 10-120 Profile 120x Standard 220.54 24.22 36.76 12.11 16.12 4.35 28 10-1 Profile x Bi-Slot Corner 9.35 9.35 4.68 4.68 6.67 1.81 20 10-160 Profile 160x80 Standard 922.50 271.10 115.30 67.80 38.10 10.29 29 10-161 Profile 16x160 287.10 3.66 35.89 4.10 12.78 3.45 24 10-164 Profile 160x Standard 517.25 33.13 64.65 16.56 21.48 5.80 28 10-180 Profile 80x Tri-Slot Corner 65.87 16.37 16.46 8.19 10.90 2.83 26 10-2 Profile x Bi-Slot Mid-Frame 9.57 9.57 4.78 4.78 6.72 1.82 20 10-3 Profile x Tri-Slot 9.13 9.82 4.57 4.78 6.75 1.82 20 10-4 Profile x Mono-Slot 8.42 8.66 4.07 4.33 5.77 1.56 20 10-5 Profile x Light 8.07 8.07 4.04 4.04 5.53 1.50 19 10-680 Profile 80x Light 60.05 15. 15.01 7.70 8.90 2. 26 11-0 Profile x Heavy 14.18 14.18 7.09 7.09 9.22 2.53 19 11-044 Profile x-45 Heavy 9. 9. 4.07 4.07 7.33 1.98 22 11-056 Profile Post 56x56 45.62 45.62 14.81 14.81 13.07 3.53 31 11-080 Profile 80x Heavy 102.00 26.73 25.50 13.37 16.59 4.58 26 11-084 Profile 80x80x Corner Heavy 129.37 129.37 27.94 27.94 23.23 6.27 30 11-088 Profile 80x80 Heavy 185.20 185.20 46.30 46.30 26.01 7.02 27 11-089 Profile 80x80 Extra Heavy 215.85 215.85 53.96 53.96 36.26 9.83 27 11-100 Profile x100 Heavy 190.29 30.84 38.06 15.42 17.88 4.94 25 11-120 Profile 120x Heavy 306.00 38.16 51.00 19.08 22.61 6.13 28 11-122 Profile 120x80 Heavy 575.07 274.46 92.75 68.61.08 10.82 27 11-124 Profile 120x120x Corner Heavy 498.10 498.10 66.20 66.20.30 10.90 30 11-128 Profile 28x160 732.11 20.45 91.51 14.36 31.33 8.46 25 11-1 Profile 160x Heavy 749.51 54.80 93.60 27. 32.30 8.72 28 11-160 Profile 160x80 Heavy 1106.92 343.37 138.37 85.84 48.22 13.07 29 11-5 Profile x Heavy Square 15.81 15.81 7.90 7.90 7.99 2.16 31 & End Caps 17 Parker Hannifin Corporation Business Unit
Series T-Slot Detail 21 8 4.5 Light Ø6.8 12.3 20 8 4.5 Standard Ø6.8 12.3 20 8 4.5 Heavy Ø6.8 12.3 Service Counterbore [19-015] 20mm dia. by 11mm deep hole for universal fastener Universal Fastener Set [20-004] comprised of the following parts: Socket Head Cap Screw [24-330-8] Universal Fastener [20-004z1] M8 T-Nut [20-058] Socket Head Cap Screw [24-345-8] Butt Fastener [20-006] Counterbore [19-015] 20mm dia. by 11mm deep hole for universal. Standard Fastener [20-002] comprised of parts: [20-002Z1] [24-120-8] End of profile tapped [19-010] to receive M8 screw of standard fastener. 7mm access hole drilled [19-011] through extrusion for access to standard fastener by M5 Allen wrench 18 Parker Hannifin Corporation Business Unit
Series x Standard & End Caps With T-slots located on all four faces this profile provides extensive mounting options for connections and accessories directly onto a structure, making this an excellent choice for general purpose applications such as workstations, machine guarding and enclosures. These profiles are weight optimized and available in light, standard and heavy ratings. Aluminum, Clear or Black Anodized (See page 9 for full material and finish specifications) Part # I X I Y W X W Y Section Weight [cm 4 ] [cm 4 ] [cm 3 ] [cm 3 ] [cm 2 ] [kg/m] 10-5 8.07 8.07 4.04 4.04 5.53 1.50 10-0 9.46 9.46 4.73 4.73 6.65 1.72 11-0 14.18 14.18 7.09 7.09 9.22 2.53 10-5 10-0 Description Unit Part # (Clear) Part # (Black) Profile x Light Cut off max. 6m 10-5 10-5B Profile x Standard Cut off max. 6m 10-0 10-0B Profile x Heavy Cut off max. 6m 11-0 *Saw Cut Needed for Cut to Length 19-001 19-001 Quick Reference for Mating Components Fasteners Structural Accessories Standard Fastener (Light) 20-014 Levelers Page 142 Standard Fastener 20-002 Casters Page 148 Universal Fastener 20-004 Plates Page 92 End Caps Gussets Page 96 x 18-813 Fasteners Page 65 x Secure 18-913 Machining & Processing Page 233 11-0 19 Parker Hannifin Corporation Business Unit
Series x Closed Face Universal Fastening Set 20-004 on x bi-slot corner profile. 10-1 These profiles are similar to X Standard profiles except closed faces are positioned in various arrangements. This provides efficient fastening in a variety of configurations while retaining a smooth surface for applications requiring aesthetically clean look. They are particularly useful in clean room, packaging, medical and pharmaceutical applications as they reduce areas where contaminants and dirt could potentially accumulate. 10-2 Technical Information Aluminum, Clear Anodized (See page 9 for full material and finish specifications) Part # I X I Y W X W Y Section Weight [cm 4 ] [cm 4 ] [cm 3 ] [cm 3 ] [cm 2 ] [kg/m] 10-1 9.35 9.35 4.68 4.68 6.67 1.81 10-2 9.57 9.57 4.78 4.78 6.72 1.82 10-3 9.13 9.82 4.57 4.78 6.75 1.82 10-4 8.42 8.66 4.07 4.33 5.77 1.56 10-3 10-4 Description Unit Part #(Clear) Profile x Bi-Slot Corner Cut off max. 6m 10-1 Profile x Bi-Slot Mid-Frame Cut off max. 6m 10-2 Profile x Tri-Slot Cut off max. 6m 10-3 Profile x Mono-Slot Cut off max. 6m 10-4 *Saw Cut Needed for Cut to Length 19-001 Quick Reference for Mating Components Fasteners T-Nuts Standard Fastener 20-014 M5 Roll-In 20-052 Universal Fastener 20-004 M6 Roll-In 20-056 Flat Plate Fast. (10-4) 20-028 M8 Roll-In 20-058 End Caps M8/ Double Roll-In 20-050 x 18-813 M6 Economy Standard 20-080 x Secure 18-913 M8 Economy Standard 20-081 20 Parker Hannifin Corporation Business Unit
Series M8 BHCS 90 Miter Connector [20-022] Ø6 x Quarter Round Profile & End Caps CornerBracket [22-146] Quarter Round [10-043] Radius Cap [18-821] 45.5 This profile is designed with a radius quarter round face and T-Slots on the remaining perpendicular sides. This is particularly useful for engineering frames, workstation edges, shelving or enclosures where a rounded edge is aesthetically or functionally desirable. Technical Information Aluminum, Clear Anodized (See page 9 for full material and finish specifications) I Part # X I Y W X W Y Section Weight [cm 4 ] [cm 4 ] [cm 3 ] [cm 3 ] [cm 2 ] [kg/m] 10-043 6.85 6.85 3.12 3.12 5.77 1.56 Description Unit Part #(Clear) Profile x Quarter Round Cut off max. 6m 10-043 *Saw Cut Needed for Cut to Length 19-001 Quick Reference for Mating Components Fasteners Radius Profile Accessories Flat Plate Fastener 20-028 Connector Cap, Radius 18-821 90 o Miter Connector 20-128Z1 Tap profile end for M8 19-010 Series Miter Connector 20-022 45 o Miter Cut 19-105 End Cap Special Miter Cut 19-104 x Quarter Round 18-843 10-043 21 Parker Hannifin Corporation Business Unit
Series Series Angled xx45 [11-044] x 45 End Cap [18-820] 10-044 Series Bi-Slot Corner [10-1] Use Series Universal Fasteners [24-004] on the inside of this joint to create a smooth exterior. 11-044 45 With angled faces and perpendicular T-Slots, profiles 10-044 and 11-044 are ideal for smoothing corners of structures for clean room, medical and pharmaceutical as well as display and workstation applications. They can also be used as gussets or for placing profiles at a 45 o angle within a structure. 10-045 and 10-060 provide T-Slots on three sides: one parallel with the closed face, and two positioned to provide a 60 o or 45 angle. These profiles are ideal for creating polygonal shaped structures. Technical Information Aluminum, Clear or Black Anodized (See page 9 for full material and finish specifications) 72 Part # I X I Y W X W Y Section Weight [cm 4 ] [cm 4 ] [cm 3 ] [cm 3 ] [cm 2 ] [kg/m] 10-044 6.71 6.71 2.98 2.98 5.68 1.53 11-044 9. 9. 4.07 4.07 7.33 1.98 10-045 16.27 34.39 7.43 9.62 10.22 2.76 10-060 12.73 42.73 6.08 10.93 9.35 2.76 10-045 10-060 60 75 36 Description Unit Part # (Clear) Part # (Black) Profile x-45 o Standard Cut off max. 6m 10-044 10-044B Profile x-45 o Heavy Cut off max. 6m 11-044 11-044B Profile x45 o. Standard Cut off max. 6m 10-045 Profile x60 Deg. Standard Cut off max. 6m 10-060 *Saw Cut Needed for Cut to Length 19-001 19-001 Quick Reference for Mating Components Fasteners Angle Profile Accessories Standard Fastener (Light) 20-014 Corner Bracket 22-146 Universal Fastener 20-004 Connector Cap, 3x45 o 18-822 End Caps Connector Cap, 2x45 o 18-836 x-45 o 18-820 45 o Miter Cut 19-105 -45 o 18-845 Special Miter Cut 19-104 -60 o 18-860 Tap profile end for M8 19-010 22 Parker Hannifin Corporation Business Unit
Series A A-60 2 60 + A 60 3 30 10-083 Series Radius 2 (A 60) 3 10-086 30 & End Caps Radius surfaces on two facing sides make these profiles particularly useful for creating rounded corners. They are ideal for applications requiring an aesthetically pleasing look, or where contaminants and dirt must be kept to a minimum such as medical and pharmaceutical environments. These profiles are also useful in constructing cases, tables and angled structure bases. Aluminum, Clear Anodized (See page 9 for full material and finish specifications) Part # A I X I Y W X W Y Section Weight [cm 4 ] [cm 4 ] [cm 3 ] [cm 3 ] [cm 2 ] [kg/m] 10-083 6.09 8.48 2.67 3.59 5.79 1.57 10-085 16.26 11.85 5.06 4.59 7.09 1.92 10-086 30. 19.27 7.94 6. 8.30 2.25 10-089 66.03 66.03 16.14 16.14 12.69 3.44 A 45 60 10-083 10-085 Description Unit Part # (Clear) Profile Rx80 30 Standard Cut off max. 6m 10-083 Profile Rx80 45 Standard Cut off max. 6m 10-085 Profile Rx80 60 Standard Cut off max. 6m 10-086 Profile Rx80 90 Standard Cut off max. 6m 10-089 *Saw Cut Needed for Cut to Length 19-001 Quick Reference for Mating Components Fasteners Structural Accessories Universal Fastener 20-004 Machining & Processing Page 233 90 10-086 10-089 23 Parker Hannifin Corporation Business Unit
Series Series 16mm 10-016 16 80 Light construction and support for attaching items such as valves, limit switches, pneumatics and control equipment. Profile 10-081 can be used as a base plate on Roller System 6 Bearing Units. Profile 10-161 has a large surface area with 8mm and 5mm T-Slots providing convenient attachment points for multiple accessories (this profile should not be used as a structural member). 10-081 16 Aluminum, Clear or Black Anodized on select units (See page 9 for full material and finish specifications) Part # I X I Y W X W Y Section Weight [cm 4 ] [cm 4 ] [cm 3 ] [cm 3 ] [cm 2 ] [kg/m] 10-016 6.97 1.06 3.49 1.23 4.33 1.17 10-081 50.76 2.15 12.69 2.69 8.13 2.20 10-161 287.10 3.66 35.89 4.10 12.78 3.45 160 Description Unit Part # (Clear) Part # (Black) Profile 16x Cut off max. 6m 10-016 10-016B Profile 16x80 Cut off max. 6m 10-081 *Saw Cut Needed for Cut to Length 19-001 19-001 Profile 16x160 Cut off max. 6m 10-161 *Saw Cut Needed for Cut to Length 19-003 10-161 16 Quick Reference for Mating Components Fasteners T-Nut Examples Butt-Fastening Set M6 20-006 M5 Roll-In Single 20-052 Flat Plate Fastening Set 20-028 M8 Roll-In Double 20-050 End Cap Structural Accessories Profile 16x 18-811 T35 Din Rail 15-083 Profile 16x80 18-812 16x Mounting Plate 22-139 Profile 16x160 18-806 24 Parker Hannifin Corporation Business Unit
Series x100 and 160x28 & End Caps 100 These heavy profiles are ideal for general engineering structures such as machine bases, structural supports and mounting surfaces on fixturing applications. 11-128 is used as a header for bearing block assemblies on Linear System 14 or 25. Aluminum, Clear (See page 9 for full material and finish specifications) Part # I X I Y W X W Y Section Weight [cm 4 ] [cm 4 ] [cm 3 ] [cm 3 ] [cm 2 ] [kg/m] 11-100 190.29 30.84 38.06 15.42 17.88 4.94 11-128 732.11 20.45 91.51 14.36 31.33 8.46 11-100 Description Unit Part # (Clear) Profile x100 Heavy Cut off max. 6m 11-100 *Saw Cut Needed for Cut to Length 19-002 Profile 28x160 Cut off max. 6m 11-128 *Saw Cut Needed for Cut to Length 19-003 160 Quick Reference for Mating Components End Cap Fasteners x100 18-804 Standard Fastener 20-002 160x28 18-816 Universal Fastener 20-004 T-Slot Nuts Page 73 28 11-128 25 Parker Hannifin Corporation Business Unit
Series 80x 80 10-680 80 Designed for applications where high strength is required. Ideal for general engineering structures such as machine frames, work stations and support structures. 10-080 and 11-080 can be used in the construction of linear slides with the IPS Roller Systems. Both profiles can also be used for compressed air piping. Aluminum, Clear Anodized (See page 9 for full material and finish specifications) 10-080 Part # I X I Y W X W Y Section Weight [cm 4 ] [cm 4 ] [cm 3 ] [cm 3 ] [cm 2 ] [kg/m] 10-680 60.05 15. 15.01 7.70 8.90 2. 10-080 71.79 17.23 17.99 8.62 11.53 3.18 11-080 102.00 26.73 25.50 13.37 16.59 4.58 10-180 65.87 16.37 16.46 8.19 10.90 2.83 80 11-080 Description Unit Part # (Clear) Part # (Black) Profile 80x Light Cut off max. 6m 10-680 Profile 80x Standard Cut off max. 6m 10-080 10-080B Profile 80x Heavy Cut off max. 6m 11-080 Profile 80x Tri-Slot Corner Cut off max. 6m 10-180 10-180B *Saw Cut Needed for Cut to Length 19-001 Quick Reference for Mating Components Fasteners Structural Accessories Standard Fastener (Light) 20-014 Compressed Air Fittings Page 154 Standard Fastener 20-002 Levelers Page 142 End Caps Plates Page 92 80x 18-814 Gussets Page 96 80x Secured 18-914 Linear Slides Page 176 80 10-180 26 Parker Hannifin Corporation Business Unit
Series Inquire about Custom Tops 80x80 and 80x120 & End Caps 80 80 10-088 Designed for heavy duty applications and construction of linear slides with IPS roller systems, these profiles are also suitable for multiple channel compressed air piping. Profile 11-089 can be used as a manifold for pressurized air (150 psi). A support bearing can be pressed into the center diameter to hold shafts or spindles for rotary applications. This diameter can also be used to house electrical or air lines. Aluminum, Clear or Black Anodized (See page 9 for full material and finish specifications) Part # I X I Y W X W Y Section Weight [cm 4 ] [cm 4 ] [cm 3 ] [cm 3 ] [cm 2 ] [kg/m] 10-088 138.30 138.30 34.58 34.58 20.17 5.45 11-088 185.20 185.20 46.30 46.30 26.01 7.02 11-089 215.85 215.85 53.96 53.96 36.26 9.83 11-122 575.07 274.46 92.75 68.61.08 10.82 80 80 11-088 80 Description Unit Part # (Clear) Part # (Black) Profile 80x80 Standard Cut off max. 6m 10-088 10-088B Profile 80x80 Heavy Cut off max. 6m 11-088 *Saw Cut Needed for Cut to Length 19-002 19-002 Profile 80x80 Extra Heavy Cut off max. 6m 11-089 Profile 80x120 Heavy Cut off max. 6m 11-122 *Saw Cut Needed for Cut to Length 19-003 Quick Reference for Mating Components Fasteners Structural Accessories Standard Fastener 20-002 Compressed Air Fittings Page 154 Universal Fastener 20-004 Plates Page 92 End Caps Gussets Page 96 80x80 18-815 Linear Slides Page 176 80x80 Secured 18-915 80x120 18-841 80 80 11-089 120 11-122 27 Parker Hannifin Corporation Business Unit
Series 120x and 160x 120 120 160 10-120 11-120 10-164 Designed for applications such as fixturing, vertical structural support and headers for bearing block assemblies on IPS Linear Systems 14 and 25, these profiles are also suitable for multiple channel compressed air piping. Aluminum, Clear Anodized (See page 9 for full material and finish specifications) Part # I X I Y W X W Y Section Weight [cm 4 ] [cm 4 ] [cm 3 ] [cm 3 ] [cm 2 ] [kg/m] 10-120 220.54 24.22 36.76 12.11 16.12 4.35 11-120 306.00 38.16 51.00 19.08 22.61 6.13 10-164 517.25 33.13 64.65 16.56 21.48 5.80 11-1 749.51 54.80 93.60 27. 32.30 8.72 160 Description Unit Part # (Clear) Profile 120x Standard Cut off max. 6m 10-120 Profile 120x Heavy Cut off max. 6m 11-120 Profile 160x Standard Cut off max. 6m 10-164 Profile 160X Heavy Cut off max. 6m 11-1 *Saw Cut Needed for Cut to Length 19-003 11-1 Quick Reference for Mating Components Fasteners T-Nut Examples Standard Fastener 20-002 M5 Roll-In Single 20-052 Universal Fastener 20-004 M8 Roll-In Double 20-050 End Caps Structural Accessories 120x 18-8 Compressed Air Fittings Page 154 160x 18-817 Machining & Processing Page 233 28 Parker Hannifin Corporation Business Unit
Series 160x80 & End Caps 160 Designed for very high load or wide span applications and construction of linear slides with IPS Roller Systems. These high strength profiles are also suitable for multiple channel compressed air piping. Aluminum, Clear Anodized (See page 9 for full material and finish specifications) Part # I X I Y W X W Y Section Weight [cm 4 ] [cm 4 ] [cm 3 ] [cm 3 ] [cm 2 ] [kg/m] 10-160 922.50 271.10 115.30 67.80 38.10 10.29 11-160 1106.92 343.37 138.37 85.84 48.22 13.07 Description Unit Part # (Clear) Profile 160x80 Standard Cut off max. 6m 10-160 Profile 160x80 Heavy Cut off max. 6m 11-160 *Saw Cut Needed for Cut to Length 19-003 Quick Reference for Mating Components Fasteners Structural Accessories Standard Fastener 20-002 Levelers Page 142 Universal Fastener 20-004 Casters Page 148 End Caps Plates Page 92 160x80 18-818 Gussets Page 96 80 80 10-160 160 11-160 29 Parker Hannifin Corporation Business Unit
Series Heavy Corner 120 80 80 11-084 11-124 120 Designed for very high load or wide span applications and construction corner posts in structures or machine assemblies. These high strength profiles are also suitable for multiple channel compressed air piping. Aluminum, Clear Anodized (See page 9 for full material and finish specifications) Part # I X I Y W X W Y Section Weight [cm 4 ] [cm 4 ] [cm 3 ] [cm 3 ] [cm 2 ] [kg/m] 11-084 129.37 129.37 27.94 27.94 23.23 6.27 11-124 498.10 498.10 66.20 66.20.30 10.90 Description Unit Part # (Clear) Profile 80x80x Corner Heavy Cut off max. 3m 11-084 Profile 120x120x Corner Heavy Cut off max. 3m 11-124 *Saw Cut Needed for Cut to Length 19-003 Quick Reference for Mating Components Fasteners T-Nut Examples Standard Fastener 20-002 M6 Roll-In 20-056 Universal Fastener 20-004 M8 Roll-In 20-058 Parallel Clamp 20-017 M8/ Double Roll-In 20-049 T-Slot Nut, HD M8 20-064 30 Parker Hannifin Corporation Business Unit
Series Mounting Option 1 Univ. Fast. Set [20-004] Mounting Option 2 Std. Fast. Set [20-002] (access hole required) T-Nut HD M8 [20-064] M8 Flat Washer [800.25] Post and Square & End Caps 6 Profile 36x36 10-036 Profile 56x56 [11-056] Rachet Handle M8x16 [23-316] Optional mounting with socket head screw 28 SQUARE 11-5 These profiles are engineered as support elements for a variety of applications including table bases, frames and machine guarding. Profile 10-036 fits into the cavity of 11-056 to create a telescoping post for work stations or tables. This cavity can also be used as a channel for counterweights. 10 36 Aluminum, Clear Anodized (See page 9 for full material and finish specifications) 36 10-036 Part # I X I Y W X W Y Section Weight [cm 4 ] [cm 4 ] [cm 3 ] [cm 3 ] [cm 2 ] [kg/m] 11-5 15.81 15.81 7.90 7.90 7.99 2.16 10-036 8.55 8.55 4.32 4.32 7.18 1.94 8.9 20 11-056 45.62 45.62 14.81 14.81 13.07 3.53 Description Unit Part # (Clear) Profile x Heavy Square Cut off max. 6m 11-5 Profile Post 36x36 Cut off max. 3m 10-036 Profile Post 56x56 Cut off max. 6m 11-056 *Saw Cut Needed for Cut to Length 19-001 20 36 SQUARE 56 56 11-056 Quick Reference for Mating Components End Caps Structural Accessories x (11-5 only) 18-805 Ratchet Handle 23-316 56x56 Secure 18-819 Flat Plate Fastener 20-028 31 Parker Hannifin Corporation Business Unit
30 Series 30 Series Moment of Inertia Section Modulus I X I Y W X W Y Section Weight Cat. Part # Description [cm4 ] [cm4 ] [cm3 ] [cm3 ] [cm 2 ] [kg/m] Page 12-030 Profile 30x30 3.13 3.13 2.09 2.09 3.31 0.09 33 12-033 Profile 30x30 Quarter Round 2.71 2.71 1.70 1.70 3.26 0.88 34 12-034 Profile 30x30 Bi-Slot Corner 3.49 3.49 2.22 2.22 3.68 0.99 33 12-035 Profile 30x30 Bi-Slot Midframe 3.49 3.49 2.22 2.22 3.68 0.99 33 12-060 Profile 30x60 21.10 6.00 7.04 4.01 6.10 1.65 35 12-066 Profile 60x60 39.00 39.00 13.00 13.00 9.61 2.60 35 T-Slot Detail 20 8 2.0 9.8 Service Counterbore [19-015] 20mm dia. by 11mm deep hole for universal fastener Universal Fastener Set [20-008] comprised of the following parts: Socket Head Cap Screw [24-327-6] Universal Fastener [20-008z1] M6 T-Nut [20-056] Socket Head Cap Screw [24-350-6] Butt Fastener [20-012] Counterbore [19-015] 20mm dia. by 11mm deep hole for universal. Standard Fastener [20-003] comprised of parts: [20-003Z1] [24-116-8] End of profile tapped [19-010] to receive M8 screw of standard fastener. 7mm access hole drilled [19-011] through extrusion for access to standard fastener by M5 Allen wrench 32 Parker Hannifin Corporation Business Unit
30 Series 30x30 & End Caps 30 30 12-030 Designed for general structures, safety guards and partition frames, light duty enclosures and industrial peripherals. Profile 12-034 has closed faces on 2 perpendicular sides making it ideal for constructing smooth corners. 30 Aluminum, Clear Anodized (See page 9 for full material and finish specifications) Part # I X I Y W X W Y Section Weight [cm 4 ] [cm 4 ] [cm 3 ] [cm 3 ] [cm 2 ] [kg/m] 30 12-034 12-030 3.13 3.13 2.09 2.09 3.31 0.90 12-034 3.49 3.49 2.22 2.22 3.68 0.99 12-035 3.49 3.49 2.22 2.22 3.68 0.99 Description Unit Part # (Clear) Profile 30x30 Cut off max. 6m 12-030 Profile 30x30 Bi-Slot Corner Cut off max. 6m 12-034 Profile 30x30 Bi-Slot Midframe Cut off max. 6m 12-035 *Saw Cut Needed for Cut to Length 19-001 30 30 12-035 Quick Reference for Mating Components Fasteners Structural Accessories Standard Fastener 20-003 Corner Bracket 30 22-150 Universal Fastener 20-008 Connector Cap 30 (Sq) 22-152 End Caps Leveling Foot 21-001-30 30x30 18-803 T-Slot Nuts Page 72 33 Parker Hannifin Corporation Business Unit
30 Series 30x30 Quarter Round M8 BHCS CornerBracket30 [22-150] 30 Quarter Round [12-033] Radius Cap 30 [22-151] 12-033 30 30 Designed with a quarter round smooth face and T-Slots, this profile is particularly useful for engineering frames, shelving or enclosures where a radius edge is aesthetically or functionally desirable. Technical Information Aluminum, Clear Anodized (See page 9 for full material and finish specifications) I Part # X I Y W X W Y Section Weight [cm 4 ] [cm 4 ] [cm 3 ] [cm 3 ] [cm 2 ] [kg/m] 12-033 2.71 2.71 1.70 1.70 3.26.88 Description Unit Part # Profile 30x30 Quarter Round Cut off max. 6m 12-033 *Saw Cut Needed for Cut to Length 19-001 Quick Reference for Mating Components Fasteners Corner Connector Caps Pg. 88 Flat Plate Fastener 20-028 Connector Cap, Radius 22-151 Miter Connector 30 20-024 Tap Profile End for M8 19-010 Corner Bracket 30 22-150 45 o Miter Cut 19-104 34 Parker Hannifin Corporation Business Unit
30 Series 30x60 & 60x60 & End Caps 60 These profiles are ideal for general use structures, safety guards and partition frames, light duty enclosures and industrial peripherals. 30 Aluminum, Clear Anodized (See page 9 for full material and finish specifications) Part # I X I Y W X W Y Section Weight [cm 4 ] [cm 4 ] [cm 3 ] [cm 3 ] [cm 2 ] [kg/m] 12-060 21.10 6.00 7.04 4.01 6.10 1.65 12-066 39.00 39.00 13.00 13.00 9.61 2.60 Description Unit Part # Profile 30x60 Cut off max. 6m 12-060 Profile 60x60 Cut off max. 6m 12-066 *Saw Cut Needed for Cut to Length 19-001 Quick Reference for Mating Components Fasteners T-Nut Examples Standard Fastener 20-003 M6 Roll-In 20-056 Universal Fastener 20-008 M8 Roll-In 20-058 End Caps M8/ Double Roll-In 20-049 30x60 18-863 T-Slot Nut, HD M8 20-064 60x60 18-866 Economy Drop-In 20-172 60 12-060 60 12-066 35 Parker Hannifin Corporation Business Unit
28 Series 28 Series Moment of Inertia Section Modulus I X I Y W X W Y Section Weight Cat. Part # Description [cm4 ] [cm4 ] [cm3 ] [cm3 ] [cm 2 ] [kg/m] Page 12-028 Profile 28x28 Quad-Slot 2.41 2.41 1.72 1.72 3.01 0.81 37 12-428 Profile 28x56 Open Slot 4.67 16.56 3.33 5.91 5.66 1.53 37 12-056 Profile 56x56 Light 29.55 29.55 14.78 14.78 8.51 2.31 37 12-128 Profile 28x28 Tri-Slot 2.69 2.41 1.82 1.72 3.18 0.86 38 12-228 Profile 28x28 Bi-Slot 2.71 2.71 1.84 1.84 3.37 0.91 38 12-328 Profile 28x28 Bi-Slot Mid-Frame 3.02 2.43 2.16 1.73 3.37 0.91 38 12-043 Profile 28x28 Quarter Round 2.71 2.71 1.84 1.84 3.49 0.95 39 12-044 Profile 28x28 45 Deg. 2.00 2.00 1.30 1.30 2.89 0.78 39 12-528 Profile 28x56 Tri-Slot 5.28 18.61 3.57 6.46 6.21 1.68 12-628 Profile 28x56 Bi-Slot 5.92 18.05 4.23 6.44 6.39 1.73 12-728 Profile 28x56 Quad-Slot 5.26 17.30 3.55 6.18 6.03 1.63 T-Slot Dimensions 18 8 2.0 8.6 Ø6.7 Service Counterbore [19-015] 20mm dia. by 11mm deep hole for universal fastener Universal Fastener Set [20-005] comprised of the following parts: Socket Head Cap Screw [24-327-6] Universal Fastener [20-005Z1] M6 T-Nut [20-055] Socket Head Cap Screw [24-350-6] Butt Fastener [20-012] Counterbore [19-015] 20mm dia. by 11mm deep hole for universal. Standard Fastener [20-003] comprised of parts: [20-003Z1] [24-116-8] End of profile tapped [19-010] to receive M8 screw of standard fastener. 7mm access hole drilled [19-011] through extrusion for access to standard fastener by M5 Allen wrench 36 Parker Hannifin Corporation Business Unit
28 Series Inquire about Custom Tops 28x28, 28x56 and 56x56 Slotted & End Caps 28 28 12-028 These profiles are designed with T-slot faces on all four sides. They are useful for constructing safety guards, partition frames, light duty enclosures and industrial peripherals. 56 Aluminum, Clear or Black Anodized on selected styles (See page 9 for full material and finish specifications) Part # I X I Y W X W Y Section Weight [cm 4 ] [cm 4 ] [cm 3 ] [cm 3 ] [cm 2 ] [kg/m] 12-028 2.41 2.41 1.72 1.72 3.01 0.81 12-428 4.67 16.56 3.33 5.91 5.66 1.53 12-056 29.55 29.55 14.78 14.78 8.51 2.31 28 12-428 Description Unit Part # (Clear) Part # (Black) Profile 28x28 Quad-Slot Cut off max. 6m 12-028 12-028B Profile 28x56 Open Slot Cut off max. 6m 12-428 Profile 56x56 Light Cut off max. 6m 12-056 *Saw Cut Needed for Cut to Length 19-001 19-001 56 Quick Reference for Mating Components Fasteners T-Nut Examples Standard Fastener 20-003 Roll-In Single M6 20-055 Universal Fastener 20-005 Roll-In Single M8 20-057 End Caps Economy Standard M6 20-090 28x28 18-808 Economy Offset M6 20-190 28x56 18-809 Economy Standard M8 20-091 56x56 (Secured) 18-819 Economy Offset ¼-20 20-193 56 12-056 37 Parker Hannifin Corporation Business Unit
28 Series 28x28 Closed Face Square 28 12-128 28 Designed with various closed faces, these profiles provide efficient fastening in a variety of configurations while retaining a smooth exterior for an aesthetically clean look. 28 Aluminum, Clear Anodized (See page 9 for full material and finish specifications) 12-228 28 Part # I X I Y W X W Y Section Weight [cm 4 ] [cm 4 ] [cm 3 ] [cm 3 ] [cm 2 ] [kg/m] 12-128 2.69 2.41 1.82 1.72 3.18 0.86 12-228 2.71 2.71 1.84 1.84 3.37 0.91 12-328 3.02 2.43 2.16 1.73 3.37 0.91 12-328 28 28 Description Unit Part # Profile 28x28 Tri-Slot Cut off max. 6m 12-128 Profile 28x28 Bi-Slot Cut off max. 6m 12-228 Profile 28x28 Bi-Slot Mid-Frame Cut off max. 6m 12-328 *Saw Cut Needed for Cut to Length 19-001 Quick Reference for Mating Components Fasteners End Caps Flat Plate Fastening Set 20-028 28x28 18-808 Universal Fastening Set 20-005 Standard Fastener 20-003 38 Parker Hannifin Corporation Business Unit
28 Series 28x28 Radius and Angled Closed Face & End Caps Ø5mm 28 Designed with a radius or angled closed face and T-Slots on two sides, these profiles are ideal for applications where perpendicular surfaces are not desired. 28 12-043 Aluminum, Clear Anodized (See page 9 for full material and finish specifications) Part # I X I Y W X W Y Section Weight [cm 4 ] [cm 4 ] [cm 3 ] [cm 3 ] [cm 2 ] [kg/m] 12-043 2.71 2.71 1.84 1.84 3.49 0.95 12-044 2.00 2.00 1.30 1.30 2.89 0.78 45 28 Description Unit Part # Profile 28x28 Quarter Round Cut off max. 6m 12-043 Profile 28x28 45 Cut off max. 6m 12-044 *Saw Cut Needed for Cut to Length 19-001 28 12-044 Quick Reference for Mating Components Fasteners T-Nut Examples Flat Plate Fastening Set 20-028 Roll-In Single M6 20-055 End Caps Roll-In Single M8 20-057 28x28-45 o 18-844 Economy Standard M6 20-090 39 Parker Hannifin Corporation Business Unit
28 Series 28x56 Closed Face 56 12-528 28 56 Designed with various closed faces, these profiles provide efficient fastening in a variety of configurations while retaining a smooth exterior for an aesthetically clean look. Aluminum, Clear Anodized (See page 9 for full material and finish specifications) Part # I X I Y W X W Y Section Weight [cm 4 ] [cm 4 ] [cm 3 ] [cm 3 ] [cm 2 ] [kg/m] 12-528 5.28 18.61 3.57 6.46 6.21 1.68 12-628 5.92 18.05 4.23 6.44 6.39 1.73 12-728 5.26 17.30 3.55 6.18 6.03 1.63 12-628 28 Description Unit Part # Profile 28x56 Tri-Slot Cut off max. 6m 12-528 Profile 28x56 Bi-Slot Cut off max. 6m 12-628 Profile 28x56 Quad-Slot Cut off max. 6m 12-728 *Saw Cut Needed for Cut to Length 19-001 56 Quick Reference for Mating Components Fasteners End Caps Flat Plate Fastening Set 20-028 28x56 18-809 Universal Fastening Set 20-005 Standard Fastener 20-003 12-728 28 Parker Hannifin Corporation Business Unit
20 Series 20 Series Moment of Inertia Section Modulus I X I Y W X W Y Section Weight Cat. Part # Description [cm4 ] [cm4 ] [cm3 ] [cm3 ] [cm 2 ] [kg/m] Page 12-120 Profile 20x10 0.53 0.12 0.53 0.24 1.29 0.35 42 12-020 Profile 20x20 0.72 0.72 0.72 0.72 1.85 0.52 42 12-0 Profile x 20 Series 8.55 8.55 4.27 4.27 4.90 1.32 42 12-081 Profile 80x14 20 Series 41.01 1.14 10.25 1.57 6.65 1.80 43 12-124 Profile 20x 5.01 1.27 2.50 1.27 3.18 0.86 43 12-125 Profile 20x80 36. 2.70 9.10 2.70 6.19 1.67 43 12-126 Profile 20x60 16.02 2.04 5.34 2.04 4.73 1.28 43 & End Caps 12 5 1.8 T-Slot Detail Ø4.3 6.4 Counterbore [19-015] 10mm dia. by 8.5mm deep hole for universal fastener Service Universal Fastener Set [20-0] comprised of the following parts: Socket Head Cap Screw [24-314-4] Universal Fastener [20-0Z1] M6 T-Nut [20-044] Standard Fastener [20-021] comprised of parts: [20-021Z1] [24-112-5] End of profile tapped [19-010] to receive M5 screw of standard fastener. 7mm access hole drilled [19-011] through extrusion for access to standard fastener by M5 Allen wrench 41 Parker Hannifin Corporation Business Unit
20 Series 20x10, 20x20 & 20x 12-120 12-020 20 20 10 20 20 Series profiles are designed for light duty enclosures and fixtures. They are also useful in building light accessories and components on workstations or assembly tables. The 5mm T-slot requires 20 Series hardware. Aluminum, Clear Anodized (See page 9 for full material and finish specifications) Part # I X I Y W X W Y Section Weight [cm 4 ] [cm 4 ] [cm 3 ] [cm 3 ] [cm 2 ] [kg/m] 12-120 0.53 0.12 0.53 0.24 1.29 0.35 12-020 0.72 0.72 0.72 0.72 1.85 0.52 12-124 5.01 1.27 2.50 1.27 3.18 0.86 Description Unit Part # (Clear) Profile 20x10 Cut off max. 3m 12-120 Profile 20x20 Cut off max. 3m 12-020 Profile 20x Cut off max. 3m 12-124 *Saw Cut Needed for Cut to Length 19-001 12-124 20 Quick Reference for Mating Components Fasteners End Caps Standard Fastener 20-021 20x10 18-830 Universal Fastener 20-0 20x20 18-802 20x 18-831 42 Parker Hannifin Corporation Business Unit
20 Series 20 Series & End Caps 12-0 20 Series profiles are designed for light duty enclosures and fixtures. They are also useful in building light accessories and components on workstations or assembly tables. The 5mm T-Slot requires 20 Series hardware. Aluminum, Clear Anodized (See page 9 for full material and finish specifications) Part # I X I Y W X W Y Section Weight [cm 4 ] [cm 4 ] [cm 3 ] [cm 3 ] [cm 2 ] [kg/m] 12-0 8.55 8.55 4.27 4.27 4.90 1.32 12-081 41.01 1.14 10.25 1.57 6.65 1.80 12-126 16.02 2.04 5.34 2.04 4.73 1.28 12-125 36. 2.70 9.10 2.70 6.19 1.67 20 60 12-126 Description Unit Part # (Clear) Profile x, 20 Series Cut off max. 3m 12-0 Profile 80x14 20 Series Cut off max. 3m 12-081 Profile 20x60 Cut off max. 3m 12-126 Profile 20x80 Cut off max. 3m 12-125 *Saw Cut Needed for Cut to Length 19-001 80 80 Quick Reference for Mating Components Fasteners End Caps Standard Fastener 20-021 x 18-832 Universal Fastener 20-0 20x60 18-834 T-Nuts 20x80 18-835 Roll-In Single M4 20-044 80x14 18-833 Roll-In Single M5 20-045 14 20 12-081 12-125 43 Parker Hannifin Corporation Business Unit
Specialty Specialty Profile Type Compatibility Part # Description Page Picture Frame 12-031 Profile 18x32 Mono-Slot 45 Bi-Slot 12-032 Profile 18x32 Bi-Slot 46 Rolling Door Guides 12-022 Profile Rolling Door Guide 47 12-421 Guide Profile UHMW 47 Sliding Door Guides 12-012 Profile Sliding Door Guide Upper 48 12-013 Profile Sliding Door Guide Lower 48 28 30 12-014 Profile Sliding Door Guide 30/28 Upper 48 28 30 12-015 Profile Sliding Door Guide 30/28 Lower 48 Panel Extrusion 12-018 Panel Extrusion 49 Stiffener/Handle Profile 12-011 Profile Stiffener / Handle 49 Mesh Clamp 28 30 12-010 Profile Mesh Clamp 49 Panel Holder 28 30 12-016 Profile Panel Holder - Black 50 28 30 12-016 Profile Panel Holder - Gray 51 Clamp Bar 12-105 Profile Clamp 51 Rack Angle 28 30 12-109 Profile Rack Angle with Holes 51 28 30 12-110 Profile Rack Angle no Holes 51 20-075 Rack Angle Clip Nut M5 51 20-076 Rack Angle Clip Nut M6 51 UHMW Slide Bar 12-0 Slide Bar UHMW 52 12-420 Slide Bar UHMW x10 52 12-420 Slide Bar UHMW x10, ANTISTATIC 52 28 30 12-420 Slide Bar UHMW 28/30x8 52 28 30 12-410 Slide Strip UHMW 52 44 Parker Hannifin Corporation Business Unit
Specialty Miter Bracket [20-127] 39.1 13.6 32x18 Picture Frame Profile & End Caps 90 Miter Connector [20-128] M6x8 Set Screw [24-508-6C] 32 x 18 Mono-Slot Profile [12-031] 32x18 Mono-Slot [12-031] 6mm Panel Vinyl Panel Gasket [12-108] 8 B A Ø6.8 THRU 10 11 32 PANEL SIZE B = A - 48mm 13.6 9 18 Light duty extrusion for frames and guarding. Accepts panels 10mm (3/8") thick without gaskets or 6mm (1/4") thick with Panel Gasket 10 (12-108). The profile has a recess for magnetic or foam foam tape to provide a tight seal against noise or dust. Aluminum, Clear Anodized Weight: 0.94kg/m Recommend using Loctite Thread Locker No. 242 to secure setscrews. End Cap 18-807 can not be used with this profile 12-031 Description Unit Part # Profile 18x32 Mono-Slot Cut off max. 6m 12-031 *Saw Cut Needed for Cut to Length 19-001 *45 o Miter Cut (each end) 19-105 *Special Miter Cut (each end) 19-104 Quick Reference for Mating Components Fasteners Structural Accessories 90 o Miter Connector 20-128Z1 Panel Gasket 10 12-108 Miter Bracket 20-127 45 Parker Hannifin Corporation Business Unit
Specialty 32x18 Bi-Slot Profile 10 Ø4.2 12.3 32 12.3 8 18 12-032 6mm Panel Using 12-106 Gasket Guide Insert Set [21-067] Panel Gasket 10 [12-108] Tap M5x14 32 x 18 Door Profile [12-032] (Small T-slot Facing out) 32x18 Fastener [20-132] 6mm Panel 32 x 18 Door Profile [12-032] (Large T-Slot facing in) Frame for holding panels with small T-slot facing out. (No milling required) M5x20 Roller Insert Set [21-068] Panel Gasket 8 [12-106] 6mm Panel 32x18 End Cap [18-807] 7.6 3 TYP Ø7 13 32x18 Door Profile [12-032] (Small T-Slot facing in) 11 16 10 32x18 Fastener [20-132] Mill Slot 9.6 15 14 Mill Detail Frame for holding panels with large T-slot facing out. (You must mill slot for fastener) 20-132 18 32 Suitable for guarding, sliding doors, and enclosures. Panels up to 9mm thick may be clamped using spring clamp (22-032). T-Slots will accept 6mm panels with Panel Gasket 8 or 10 (12-106 and 12-108). Description Unit Part # Profile 18x32 Bi-Slot Cut off max. 6m 12-032 *Saw Cut Needed for Cut to Length 19-001 Aluminum, Clear Anodized Weight 0.67 kg/m Fastening Set: Steel, galvanized Weight: 9.0 g Clamp Spring: Steel Weight: 4g 18-807 Quick Reference for Mating Components 6 7 Fasteners Structural Accessories 32x18 Bi-Slot Fastener 20-132 Panel Gasket 8 12-106 Clamp Spring 22-032 Panel Gasket 10 12-108 End Caps Roller Insert Set 21-068 32x18 18-807 Guide Insert Set 21-067 10 12-108 46 Parker Hannifin Corporation Business Unit
Specialty Series Profile Handle Guide Insert [21-067] Fastening See Detail 4 24.5 Rolling Door Guide Profile & End Caps 66 60 6mm (1/4") Panel B C A 21 3X10 Vinyl Panel Gasket [12-106] 12 6 T-Slot 8 T-Slot 10 8.0 12-022 1 Rolling Door Guide Profile [12-022] Door Framed by 32x18 Bi-Slot [12-032] 2 Roller Insert [21-068] 23.5 12.5 Standard Fastening Set [20-002] Drill & Tap M5 x 10mm Deep On Center 50 25 Connection Method 1 41 OR Leave 5mm Clearance for Std. Fastener 4 Flat Plate Connector [20-028z1] * Recommend fastener every 250mm 20 M5x12BHCS [24-312-5L] M6x16 Set Screws 10 25 Mill Key Back 5mm 2mm Gap 21-067 3 Connection Method 2 5 2mm Gap Designed for large doors with removable door panels for maintenance. s include case packers, material handling equipment, packaging installations and access panels for large machine enclosures. Profile Aluminum, Clear Anodized Weight: 1.78 kg/m Guide Insert UHMW (white) Roller Insert Roller: Delrin (black) Housing: Aluminum, Clear Anodized Pin: Steel Description Unit Part # Profile Rolling Door Guide Cut off max. 4m 12-022 Guide Profile UHMW Cut off max. 3.1m 12-421 *Saw Cut Needed for Cut to Length 19-001 M6 Econ. T-Nut [20-190] M6x14SHCS [24-314-6] 10 Opt. Spring [24-719-6] 52 Ø25.4 18 9.9 10 21-068 Quick Reference for Mating Components Roller Insert Set Roller Set including (1) Housing, (1) roller, (2) M6x14 SCHS screws and (2) Offset T-Slot nuts with compression spring 21-068 Guide Insert Set Guide Set including (1) 50mm guide insert, (2) M6x16 setscrews 21-067 14 3.5 24.5 12-421 47 Parker Hannifin Corporation Business Unit
Specialty Sliding Door Guide Profile 28 Series Sliding Door Guide Upper 17 A B 2 TYP. Any Panel (up to 1/4") 7 TYP. 12-012 R2 29 7 TYP. 2 TYP. Stiffener/Handle [12-011] Sliding Door Guide Lower 10 B = A - 15mm for removable doors B = A - 10mm for non-removable doors *Designed for panels up to 1/4 (6.4mm) 29 12-013 7 2 16.9 2 1.6 These profiles create light duty sliding panels for windows and access ports for safety guards, enclosures or partitions. Installation onto, 30 or 28 series profiles do not require fasteners and will snap into the T-Slot. The lower guides are designed to reduce friction. The upper guides facilitate lift-out removal of the panel without disassembly. Tamper proof mounting may also be provided. Aluminum, Clear Anodized Three panel tracks Panel width up to 6.4mm Weight: 12-012, 12-014 0.45kg/m 12-013, 12-015 0.50kg/m 12-014 R2 28 28 7 TYP. 1.5 TYP. 10 2 Description Unit Part # Series Profile Sliding Door Guide Upper Cut off max. 3m 12-012 Profile Sliding Door Guide Lower Cut off max. 3m 12-013 28/30 Series Profile Sliding Door Guide 30/28 Upper Cut off max. 3m 12-014 Profile Sliding Door Guide 30/28 Lower Cut off max. 3m 12-015 *Saw Cut Needed for Cut to Length 19-001 12-015 Quick Reference for Mating Components Structural Accessories Panels Page 102 48 Parker Hannifin Corporation Business Unit
Specialty Designed as a combination handle and stiffener for sliding panel doors (1/4" thick material). Panels snap into the profile slot and may be secured by an adhesive or a fastener. Aluminum, Clear AnodizedWeight: 0.93kg/m Stiffener/Handle [12-011] Stiffener/Handle Profile 18 4.6 23.9 & End Caps Description Unit Part # Panel Extrusion Cut off max. 3m 12-011 *Saw Cut Needed for Cut to Length 19-001 6.1 10.7 12-011 Extrusion for mounting 34mm (1.34") thick insulation panels onto Series profiles. Extrusion can be serviced to mount on profile using T-Slot nuts or with double sided tape. Aluminum, Clear Anodized Weight: 0.48kg/m Insulated Panel Panel Extrusion [12-018] Fastener Set [20-058 and 24-212-8] Series Profile Panel Extrusion 38.1 34 15.6 7.8 2.5 Description Unit Part # Panel Extrusion Cut off max. 6m 12-018 *Saw Cut Needed for Cut to Length 19-001 12-018 49 Parker Hannifin Corporation Business Unit
Specialty Mesh Clamp Profile Flat Bar 12.7 x 3.2 M6x6SetScrew [25-506-6F] Captures wire mesh panels up to 5.5mm thick. Excellent for constructing safety guards. Installs onto, 30 and 28 series profiles without additional fasteners. A B Length=A-1mm Length = B - 33mm 15.8 200mm ±2mm TYP 0-5.5 Aluminum, Clear Anodized Weight: 0.53 kg/m Tapped for M6 every 200mm (±2mm) Includes clamp strip and M6X6 flat point screws * Wire Mesh Size: A - 6mm and B-6mm 2 18 8 Standard fastener position is critical to avoid interference with the mesh clamp. 12-010 Description Unit Part # Mesh Clamp Profile Cut off max. 4m 12-010 *Saw Cut Needed for Cut to Length 19-001 Clamp Bar Attaches Series profiles to base plates or other parts. Must be used in pairs. Not recommended for linear applications. 20 12-105 15 20 5 Aluminum, Clear Anodized Weight: 1.24 kg/m M8 BHCS Cut to Length and Service as required. Description Unit Part # Clamp Bar Profile Cut off max. 2m 12-105 *Saw Cut Needed for Cut to Length 19-001 50 Parker Hannifin Corporation Business Unit
Specialty 10.5 50.5 67 27 Rack Angle Profile 5.8 2.5 & End Caps 1 (19 ) 27.6 18 4.8 13.7 2 3 4 5 1 Mounting dimensions 2 Inserting rack angle into series T-slot 3 Rack Angle is secured in T-slot with set screw M6x12 4 Panel is attached to Rack Angle with M5 or M6 screw and clip nut 5 Non-removable panels can be attached to the blank Rack Angle 44.5 (1U) 3.2 15.9 9.5 15.9 9.5 2.9m MAX Used for attaching standard 19" rack components to, 30 and 28 Series (30 and 28 series require installation from end of profile). 12-109 is machined with square holes for installation of M5 or M6 Clip Nut. 12-110 is blank and can be used to support horizontal panels such as ceiling tiles.clip Nut snaps into square holes for attaching panels and accessories Extrusion Aluminum, Clear Anodized Weight: 12-109 0.62kg/m 12-110 0.63kg/m Includes M6X12 flat point set screws Clip Nut (Order separately) Steel, Zinc Plated Weight 5g Due to almost identical geometry, M5 Clip nut will accept #10-32 UNF thread screws. 50 100 TYP 2.9m MAX M6 12-109 Description Unit Part # Profile Rack Angle with Holes Cut off max. 2.9m 12-109 Profile Rack Angle no Holes Cut off max. 2.9m 12-110 *Saw Cut Needed for Cut to Length 19-001 Rack Angle Clip Nut M5 1 pc 20-075 Rack Angle Clip Nut M6 1 pc 20-076 50 100 TYP M6 12-110 M5 M6 20-075 51 Parker Hannifin Corporation Business Unit
Specialty UHMW Slide Bar & Slide Strip 39.6 39.6 Service Slide bar and use appropriate screws and t-nuts. 4.7 16 7.9 12-0 39.6 16 7.8 10 4.7 Durable, low-friction material that is self lubricating and easily machined. These profiles provide a smooth gliding surface for a wide range of applications including linear systems to adjustable work surfaces or sliding panels. Extrusion UHMW, White UHMW, Black Antistatic (12-420B) Series s use: 12-0, 12-420, 12-420B and 12-410 28/30 Series s use: 12-430 or 12-410 12-420 27 7.9 8 2 Description Unit Part # Slide Bar UHMW Cut off max. 3m 12-0 Slide Bar UHMW x10 Cut off max. 3m 12-420 Slide Bar UHMW x10, ANTISTATIC Cut off max. 3m 12-420B Slide Bar UHMW 28/30x8 Cut off max. 3m 12-430 Slide Strip UHMW Cut off max. 3m 12-410 *Saw Cut Needed for Cut to Length 19-001 16 12-430 31.8 5.4 7.9 12-410 7.9 52 Parker Hannifin Corporation Business Unit
Profile Accessories These bright covers provide high visibility for caution areas of, 30 or 28 Series guards and enclosures. Covers also prevent dirt and debris from collecting in the T-slot. Rigid PVC, Yellow Safety Cover 24 0.8 7.8 12-112 & End Caps Series Description Unit Weight Part # 30/28 Safety Cover Strip 1 pc at 3m 0.3 kg 12-112 Safety Cover Strip 1 pc at 3m 12-113 34 12-113 Anti-Skid Cover Cover for Series profiles is used for non-slip surfaces such as ladders and stops for sliding doors. Oil and water resistant. Rubber, Black Hardness 80 Shore Description Unit Weight Part # Anti-Skid Cover Cut off max. 20m 180 g/m 12-114 32 4 4.5 8 12 12-114 53 Parker Hannifin Corporation Business Unit
Profile Accessories Panel Gasket 8 6.5 13 Panel gasket for installing 6mm panels in, 30 and 28 Series profile T-slot. Molded vinyl (Grey) Weight: g/m 8 Add 8mm per side of panel for T-slot inserted panel using the 12-106. 12-106 Description Unit Part # Panel Gasket 8 Cut off max. 30.5m 12-106 Panel Gasket 10 10 6 7 Panel gasket for installing 6mm panels in T-slots of 45 Series or 32x18 Door Profile. Molded vinyl (Clear) Weight: 90g/m 12-108 Description Unit Part # Panel Gasket 10 Cut off max. 125m 12-108 Mesh Gasket 8 Mesh gasket for mounting 12 gage wire mesh in, 30 and 28 Series T-Slots. Add length per side of panel for T-slot inserted mesh using the 12-107. 12-107 11 6.5 2 Molded vinyl (Clear) 10 for Series 7 for 30 Series 6 for 28 Series Weight: 90g/m Description Unit Part # Mesh Gasket 8 Cut off max. 30.5m 12-107 54 Parker Hannifin Corporation Business Unit
Profile Accessories B A Cover/Gasket Strips & End Caps T-slot covering can be cut easily with tin snips. Wires and cables can be concealed in T-slot with use of T-slot cover. Series A (mm) B (mm) /30 6 10 28 4-6 7 20 2 6 11.5 8.8 6.3 12-101 Primarily used to cover the T-Slot to prevent dust and debris from building up, or to conceal wiring routed in the T-Slot. These covers can also be inverted and used as a panel gasket. These items are easily cut with tin snips. Polypropylene Colors: Semi-clear, Black or Yellow Weight: Series 52g/m 28 Series 44g/m 20 Series 27g/m Part # Part # Part # Part # Description Unit (Clear) (Black) (Yellow) (Gray) Cover/Gasket Strip Series Each at 2m 12-101 12-101B 12-101Y 12-101G Cover/Gasket Strip 20 Series Each at 2m 12-115 12-115B Push-in Panel Seal Each at 2m 12-117 8.8 6.3 5.3 12-115 12-117 Cover Strips Used to cover the T-Slot to prevent dust and debris from building up, or to conceal wiring routed in the T-Slot. Aluminum, Anodized Colors: Clear or Black PVC Colors: Black or Blue on select styles Part # Part # Part # Description Unit (Clear) (Black) (Blue) Aluminum Cover Strip Series Each at 2m 12-102 12-102B Aluminum Cover Strip 30/28 Series Each at 2m 12-104 12-104B PVC Cover Strip Series Each at 2m 12-111B 12-111BL PVC Cover Strip 30/28 Series Each at 2m 12-116 12-116B 4.1 2.3 9.6 9.7 12-102 12-104 3.8 5.1 9.5 8.8 12-111 12-116 55 Parker Hannifin Corporation Business Unit
Profile Accessories End Caps Caps are used to cover the exposed ends of profiles after assembly. The caps provide both protection from potentially sharp edges, and also an aesthetically pleasing appearance. Glass-Filled Nylon (Black) 4 13 A A A B B B 45 R1.50" Series Description (A x B) Unit Wt (g) Part # Series x16 Each 4 18-811 x Each 7 18-813 x Heavy Square Each 10 18-805 x Quarter Round Each 5 18-843 x100 Each 20 18-804 50x50 Each 10 18-810 80x16 Each 6 18-812 80x Each 15 18-814 80x80 Each 28 18-815 120x Each 22 18-8 120x80 Each 43 18-841 160x16 Each 10 18-806 160x28 Each 20 18-816 160x Each 28 18-817 160x80 Each 66 18-818 x-45 o Each 6 18-820 -45 o Each 4 18-845 -60 o Each 5 18-860 R/80-30 Each 17 18-883 R/80-45 Each 19 18-885 R/80-60 Each 22 18-886 R/80-90 Each 25 18-889 30 Series 30 x 30 Quarter Round Each 4 18-838 30x30 Each 5 18-803 60x30 Each 11 18-863 60x60 Each 19 18-866 B B A A 56 Parker Hannifin Corporation Business Unit
Profile Accessories Assembly Hint Press end cap into end hole(s), then lightly tap with rubber or plastic mallet. End Caps Access Hole Plug B & End Caps A B Series Description (A x B) Unit Wt (g) Part # 28 Series 28x28 Each 4 18-808 28x56 Each 8 18-809 56x56 Each 16 18-819 28x28-45 o Each 3 18-844 20 Series 20x10 Each 0.5 18-830 20x20 Each 1 18-802 20x Each 2 18-831 20x60 Each 3 18-834 20x80 Each 4 18-835 x, 20 Series Each 4 18-832 80x14 Each 3 18-833 Specialty 32x18 Door Profile Each 3 18-807 Access Hole Plugs 7mm Plastic Each 0.1 18-710 7mm Nickel Each 0.5 18-713 A A R1.50" B Secured End Caps are attached to profile end with push-in fastener (sold separately). No profile servicing is required. Glass-Filled Nylon (Black) Screw: St, black oxide Secure End Caps 18-913 18-914 Description Unit Weight (g) Part # x - Secure Each 7 18-913 80x - Secure Each 23 18-914 80x80 - Secure Each 26 18-915 Push-in Fastener Each 2 18-715 18-915 57 Parker Hannifin Corporation Business Unit
Notes 58 Parker Hannifin Corporation Business Unit
Conduit Elements Conduit profiles provide a convenient way to integrate cable, hose and control components to an IPS structural assembly or linear system. These anodized aluminum profiles are modular and provide great flexibility and are easy to assemble. The dimensions are based on mm increments and are compatible with all standard IPS elements. Assembled conduit sections may be attached to any IPS profile using standard T-Sot fastening methods. Reference grooves allow for accurate positioning of any necessary holes or machining. IPS conduit profiles offer snap-together assembly that can be secured with optional locking screws. Conduit Elements Modular Dimensions & End Caps 80 120 typ 80 120 160 The conduit is made up of high tensile strength aluminum elements: Wall duct profile, 80 and 120 Conduit support profile, 80, 120 and 160 (with or without T-slot) Wall duct profiles of any required length are snapped into a support profile. Another support profile closes the duct with a "snap in" fit. The conduit may be secured with screws where necessary. Assembly of Conduit Elements 1 2 1 Scored groove for locating locking screw (24-695) in Support Profile. 2 Locking screw turned into the preextruded threads of the support wall profiles. 59 Parker Hannifin Corporation Business Unit