Event Notification Module - PDF Free Download

SAFETY INFORMATION Read these instructions carefully and look at the equipment to become familiar with the device before trying to install, operate, service, or maintain it. The following special messages may appear throughout this bulletin or on the equipment to warn of potential hazards or to call attention to information that clarifies or simplifies a procedure. The addition of either symbol to a Danger or Warning safety label indicates that an electrical hazard exists which will result in personal injury if the instructions are not followed. This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death. DANGER DANGER indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. WARNING WARNING indicates a potentially hazardous situation which, if not avoided, can result in death or serious injury. CAUTION CAUTION indicates a potentially hazardous situation which, if not avoided, can result in minor or moderate injury. NOTICE NOTICE is used to address practices not related to physical injury. The safety alert symbol shall not be used with this signal word. PLEASE NOTE Electrical equipment should be installed, operated, serviced, and maintained only by qualified personnel. No responsibility is assumed by Schneider Electric for any consequences arising out of the use of this material. Do not base your maintenance or service actions solely on messages and information displayed by the software. 2014 Schneider Electric. All Rights Reserved. 2

Introduction Event Notification Module installation is one step in the commissioning of a system. The current install allows for a great deal of flexibility including both local and remote database instances. To facilitate remote installation the setup allows the user to choose from three install paths. Complete Installation The Event Notification Module and the SQL database will reside on the same server host and the user is required to choose an SQL instance on the local machine for the install to configure the database server. Database Server Installs the database components on the target database server for Event Notification Module. Application Server The user must select the target database server, but only the application components will be installed. The user must install the database server first. For reference the following have been provided in this guide: Requirements Hardware and Software requirements that must be met in order to install ENM. Upgrades Upgrade cases which have been detailed for previous users. 2014 Schneider Electric. All Rights Reserved. 3

Requirements Please note the following system requirements when installing or using Event Management solutions. NOTE For server systems where SQL Server will also be installed, please refer to the SQL requirements to ensure the system is up to hosting both SQL and ENM. Hardware Component Processor Memory Hard Drive Network Minimum Required Quad Core 4 GB 150 GB Software Component Required Operating System Windows 7 Windows Server 2008 SP 2 Windows Server 2008 R2 Windows Server 2012 Windows Server 2012 R2 Windows 8 Windows 8.1 SQL Server MS SQL Server 2008 R2 MS SQL Server 2012 MS SQL Server Express 2012 Language English Other Internet Information Services Version 7.0 or later.net Version 4.5.1 Internet Explorer 9, 10, and 11 (Non Compatibility Mode) Chrome 20+ Firefox 14+ 2014 Schneider Electric. All Rights Reserved. 4

Upgrades Note: To upgrade a system that has an ENM 7.1 configuration to ENM 8.2, please see the steps that follow. Upgrading from ENM 7.1 to ENM 8.2 - Uninstall ENM 7.1 through Control Panel -> Programs and Features. - Install ENM 8.2 by running the install Note that during the Configuration step of the Upgrade three Tasks will occur: - Backing Up Previous Historical Data o Backs up the PLES_AEHistory Database to the Database Location selected in the installer. - Trimming Previous Historical Data o Trims the PLES_AEHistory Database to 2,000,000 records. - Migrating Previous Historical Data o Converts the data into the new ENM 8.2 Schema. 2014 Schneider Electric. All Rights Reserved. 5

This process will upgrade the database to a new Database Schema followed in ENM 8.2, automatically preserving the ENM 7.1 Database. This is an irreversible change. To use the ENM 7.1 database backup, it must be restored to another ENM 7.1 system. 2014 Schneider Electric. All Rights Reserved. 6

Complete Installation ENM and Database on same server. Start the install by running the Mainsetup.exe. License Agreement: -Click on the I Agree button to proceed with the install. Setup Type: Standalone - Select Event Notification Module Complete. - Click Next to proceed. 2014 Schneider Electric. All Rights Reserved. 7

- Otherwise you could select a different install location by clicking the button with the ellipse (See diagram below). NOTE When installing Event Notification Module (ENM) and Sequence of Events Recorder (SER) on the same machine, they are required to share the same File Destination. Files are shared between both products that are fundamental to proper behaviour. When installing on the same machine verify what location these products may be installed. 2014 Schneider Electric. All Rights Reserved. 9

Database Server: -By default the local database instance is selected. The format displayed is machine name\database instance ; please ensure it is correct. After this, provide the login credentials (username and password) associated with the database, and click Next to continue. 2014 Schneider Electric. All Rights Reserved. 10

Note: When PowerLogic SCADA or PowerSCADA Expert is installed then an additional Screen will ask for Citect Credentials (see image below). Enter in the username and password with Administrative Privileges for the accompanying Citect Project which requires Event Notification. 2014 Schneider Electric. All Rights Reserved. 12

Database Maintenance Credentials: - Please enter credentials belonging to a Local Windows Administrator associated with the machine which ENM is being installed. The username and password credentials will be verified in the following screen. Note: A Domain Admin is not a supported configuration due to the great amount of variation in possible Domain Rule/Rights. 2014 Schneider Electric. All Rights Reserved. 13

Database Maintenance Destination: -Click Next to have Database Maintenance scripts installed in the default location. You will be prompted to create a new folder if it s a new install. 2014 Schneider Electric. All Rights Reserved. 14

Check System: This is where the ENM application checks to see if the requirements are met. If there is an issue with any requirement, the user will be notified and the installation will not proceed until the issue is corrected. The program verifies the following: - Operating System - Previous ENM installs - Formal Product Name - PME Version (If ION E/SPM/ or PME is installed) - Previous SER installs - SQL Server version - Local SQL instance - SQL Server connection - SQL Server permissions - Previous Historical Database Schema Version -.NET 4.5.1 - ASP.NET - Shared Components - Database maintenance credentials - Verify SQL Mixed Mode Authentication 2014 Schneider Electric. All Rights Reserved. 16

Ready to Configure: This is where configuration choices are displayed before being installed. Please ensure that this configuration is correct before proceeding with the installation. See the screen shot for details: 2014 Schneider Electric. All Rights Reserved. 18

Configure System: -ENM configuration settings are applied. -Please note that Advosol OPC Core Component needs to be installed (Accept the license agreement for Advosol OPC Core Component - Required). Please see the image below: 2014 Schneider Electric. All Rights Reserved. 20

-If any errors were encountered while configuring the system, the page will display Configuration failed. Click on the configuration step(s) that failed, and then click on Open Log to diagnose the error. Click on try again to try configuring the system again. Complete: -This page is displayed after the install is successful and provides a link to the Installation Log. Click on the Close button to end the install. ENM is ready to be used. 2014 Schneider Electric. All Rights Reserved. 22

-Upon install there are three shortcuts which are pasted on the desktop named ENM Configuration, Alarm Sentry, and Monitoring and Diagnostics. -Please refer to the ENM Configuration Guide, Alarm Sentry Configuration Guide, and the Monitoring and Diagnostics guide respectively for functionality. 2014 Schneider Electric. All Rights Reserved. 23

Database Server Install Distributed install requires two machines; Database server and Application Server. ENM database is installed on the database server and ENM components are installed on the Application Server. Procedure Start the install by running the Setup.exe. Please note for a distributed system install, the database server needs to be installed before installing the Application Server. License Agreement: -Click on the I Agree button to proceed with the install. 2014 Schneider Electric. All Rights Reserved. 24

Database Server: -By default the local database instance is selected. The format displayed is machine name\database instance ; please ensure it is correct. There after provide the login credentials (username and password) associated with the database, and click Next to continue. Database Maintenance Credentials: - Please enter credentials belonging to a Local Windows Administrator associated with the machine which ENM is being installed. The username and password credentials will be verified in the following screen. Note: A Domain Admin is not a supported configuration due to the great amount of variation in possible Domain Rule/Rights. 2014 Schneider Electric. All Rights Reserved. 27

Check System: This is where the ENM application checks to see if the requirements are met. If there is an issue with any requirement, the user will be notified and the installation will not proceed until the issue is corrected. The program verifies the following: - Operating System - Formal Product Name - PME Version (If ION E/SPM/ or PME is installed) - Previous SER installs - SQL Server version - Local SQL instance - SQL Server connection - SQL Server permissions - Previous Historical Database Schema Version - Shared Components - Database maintenance credentials - Verify SQL Mixed Mode Authentication 2014 Schneider Electric. All Rights Reserved. 28

Ready to Configure: -This is where configuration choices are displayed before being installed. Please ensure that this is the desired configuration before proceeding with the installation. -If the configuration is not right, the use may go back (via the Back button) and correct the configuration problems. -Please see the screen shot for details: 2014 Schneider Electric. All Rights Reserved. 30

Configure System: -ENM configuration settings are applied; and if successful the following screen is displayed. Otherwise one is alerted of the configuration issue. Complete: Upon successful Database Server install the following screen is displayed; click on the close button to end the install. 2014 Schneider Electric. All Rights Reserved. 32

Application Server Install Procedure -Launch ENM installer on the Application Server Machine. Please note for a distributed system install, the database server needs to be installed before installing the Application Server. License Agreement: -Click on the I Agree button to proceed with the install. Setup Type: - Select Application Server (by clicking the drop down arrow to select the Application Server option). - Click Next to proceed. 2014 Schneider Electric. All Rights Reserved. 33

File Destination: Click Next to have ENM installed in default location. You will be prompted to create a new folder if it s a new install. Click Yes to confirm creating a new folder for the application. 2014 Schneider Electric. All Rights Reserved. 34

Database Server: -Select the database server instance from database server. The format displayed is machine name\database instance ; please ensure it is correct. There after provide the login credentials (username and password) associated with the database, and click Next to continue. Database Maintenance Credentials: - Please enter window s administrator login credentials associated with the machine that ENM is being installed. The username and password credentials get verified in the screen that follows. 2014 Schneider Electric. All Rights Reserved. 35

Check System: This is where the ENM application checks to see if the requirements are met. If there is an issue with any requirement, the user will be notified and the installation will not proceed until the issue is corrected. The program verifies the following: - Operating System - Formal Product Name - PME Version (If ION E/SPM/ or PME is installed) - Previous SER installs - SQL Server connection - Previous Historical Database Schema Version -.NET 4.5.1 - ASP.NET - Shared Components 2014 Schneider Electric. All Rights Reserved. 36

Copy Files: ENM Files are copied to the machine: Configure System: -ENM configuration settings are applied. - Please note that Advosol OPC Core Component needs to be installed (Accept the license agreement for Advosol OPC Core Component - Required). Please see the image below: 2014 Schneider Electric. All Rights Reserved. 38

Complete: Upon successful Application Server install the following screen is displayed; click on the close button to end the install. ENM is ready to be used. -Upon install there are three shortcuts which are pasted on the desktop named ENM Configuration, Alarm Sentry, and Monitoring and Diagnostics. -Please refer to the ENM Configuration Guide, Alarm Sentry Configuration Guide, and the Monitoring and Diagnostics guide for functionality. 2014 Schneider Electric. All Rights Reserved. 40