WAGO-I/O-SYSTEM 750 IO-Link Master
What is IO-Link? Line Control IODD 750-657 High Functionality (Smart) IO-Link is the first, globally standardized I/O technology (IEC 61131-9) for communication with both sensors and actuators. The powerful point-to-point communication is based on the well-known 3-wire sensor/actuator connection, and places no additional demands on the cable material. IO-Link is thus not a fieldbus, but instead the further development of previous, tested connection technology for sensors and actuators. Simple and Compatible (Universal) The connection between the IO-Link master and device takes place using an unshielded, 3-wire cable, maximum 20 m in length. The wiring is standardized. Each port of an IO-Link master can process binary switching signals and analog values (e.g., 8, 12, 16 bits). Serial IO-Link communication takes place using the same port. The simple wiring, automated parameterization, and expanded diagnostics are only a few advantages of IO-Link. Two bytes of process data are available per cycle, as standard. Transmission between the IO-Link master and device takes place within 400 μs at a speed of 230 kbaud. The user can also select larger data packets (frame types). Therefore, greater process data with up to 32 bytes in length can also be transmitted at a correspondingly lower cycle time. To ensure that the parameter data of a device is not lost when the device is replaced, it is possible to automatically store it directly in the IO-Link master. If a new, identical replacement device is connected, the parameters from its predecessor are transmitted automatically to the new device. Simple Handling (Easy) Each IO-Link device has an IODD (IO Device Description). This is a device description file, which contains information about the manufacturer, item number, functionality, device type, serial numbers, parameters and process data descriptions, and, depending on design, plug type and housing type, for example. This information can be easily read by the user and further processed. Each device is uniquely identified by the IODD and also by an internal device ID. Source: www.io-link.com
High Cost Efficiency Using IO-Link Save time and money due to:... standardized interfaces (IEC 61131-9) for simple communication with the device... easy configuration... consistent wiring... independent of the recorded data... additional information (diagnostics, quality assurance)... small spatial requirements... single tool for all devices... easy handling due to IODD device descriptions... less expense required for training... lower qualification level required... compatible with all relevant fieldbuses 1 2 4 3 L+ C/Q IO-Link SIO 4.8 / 38.4 / 230 kbit/s L+ C/Q IO-Link Device L- L- IO-Link Master Additional information is available at:
Innovative Potential with IO-Link-Master One Module Instead of Four! Classic Solution With IO-Link IODD 750-657 13 14 W W 1 9 2 10 3 11 4 12 5 13 6 14 7 15 8 16 A B C D Classic connection of complex sensors using different interfaces Different tools (A, B, C, D) for different sensors/actuators One interface for all possibilities One tool for all IO-Link devices
750-657 4-Channel IO-Link Master Module Features IO-Link master as part of the WAGO-I/O-SYSTEM 750 Four IO-Link channels in 3-wire technology in 16-channel housing, 12 mm wide Four additional potential connections (or 2/4 digital inputs) Communication with IO-Link device via standard connection technology Transmission of digital and analog values while maintaining the digital I/O function 24 V via power jumper contacts Transmission rates: 4.8 kbaud, 38.4 kbaud, 230.4 kbaud Process data width: 4 24 bytes Parameterizable using WAGO-I/O-CHECK and function blocks Approvals: Conformity marking 1 r UL 508 User-Friendly Configuration and Parameterization via WAGO-I/O-CHECK Additional information is available at:
IO-NA-US-DE-FP-130801_001 0888-0581/0100-6901 I/O LINK MASTER 1.0 US 01/2014-00 Printed in Germany Subject to design changes WAGO Kontakttechnik GmbH & Co. KG Postfach 2880 32385 Minden Hansastraße 27 32423 Minden Phone: Headquarters +49 (0)571/887-0 Sales +49 (0)571/887-222 Order Service +49 (0)571/887-333 Technical Support +49 (0)571/887-555 Fax: +49 (0)571/887-169 E-mail: info@wago.com Online: www.wago.com