SMA Connectors Series Content Page Description.. 2 Interface Dimensions.. 2 Interface Dimensions in mm/inches.. 2 Characteristics. 3 Cable Connectors 4 PCB Connectors 11 Panel Receptacles.. 13 Adapter Connectors. 18 Termination 25 Assembly Instruction.. 26 1
Description SMA is an acronym for SubMiniature version A and was developed in the 1960's. Its compact design, high durability and outstanding electrical performance have made it one of the most widely used connectors in RF and Microwave applications. Normally utilized in frequency ranges from DC-18 GHz, there are also precision versions that can work effectively up to 26.5 GHz. SMA is a 50 ohm impedance connector with a threaded interface for increased reliability and is suitable for a wide range of applications. It is also available in Reverse Polarity (RP) versions, where the male and female interface is switched. Interface Dimensions E D C REF. Plug (male) G F B A UNS-2B A B F G H I D C E REF. Jack (female) Interface Dimensions (mm/inches) Plug Jack min. max. min. max. A 4.95/.181 4.59/.181 B 4.18/.165 4.18/.165 C 2.54/.100 2.67/.105 D 0.38/.015 1.14/.045 1.88/.074 1.98/.078 E 0.00/.000 0.25/.010 0.00/.000 0.25/.010 F 1.24/.049 1.29/.051 1.24/.049 1.29/.051 G 0.90/.036 0.94/.037 0.38/.015 1.14/.045 H 4.32/.170 I 5.54/.218 Interface dimensions conformable to the standards: International: IEC 60169-15 Europe: CECC 22110 USA: MIL-C-39012, SMA Interface MIL-STD-348a/310 GB: BS 9210 N 0006 F: NF-C-93563(KMR) 2
Characteristics ELECTRICAL REQUIREMENTS Impedance 50 Frequency range DC to 18 GHz Dielectric Withstanding Voltage 2500 V rms 50 Hz, sea level Working Voltage 1,000 V rms 50 Hz, sea level Straight connector,.141": 1.23 (DC~18GHZ) VSWR Straight connector, RG316: 1.19 (DC~6GHZ) Right angle connector,.141": 1.39 (DC~18GHZ) Right angle connectorrg316: 1.28 (DC~6GHZ) Insulation Resistance 5 10³ MΩ min.(initial) Contact Resistance - Center contact 3.0 m max.. - Outer contact 2.5 m max. RF-leakage DC to 3 GHz 3GHzto6GHz -90 db min. -75 db min. MECHANICAL REQUIREMENTS Recommended Coupling Nut Torque Standard: 0.8 Nm1.1 Nm / 7.19.7 in. lbs Brass: 0.45 Nm /4.0 in. lbs Coupling Nut Retention Force Contact Captivation Cable Retention Force - cable 2.6/50 - cable 5/50 -cable.085/50 -cable.141 Durability ( Mating Cycles) 270 N /60.7 lbs Axial: 27 N/6.1 lbs 110 N/25 lbs 150 N/33.75 lbs (single braid) 200 N/48 lbs (double braid) 135 N/30 lbs 270 N/60.75 lbs 500 min. ENVIRONMENTAL REQUIREMENTS Temperature Range -65 C to +165 C Climactic Category IEC55/155/21 Corrosion Salt spray test acc. to MIL-STD-202, Method 101, Condition B Moisture Resistance MIL-STD-202 F, Method 106 Vibration MIL-STD-202, Method 204, Condition D Shock MIL-STD-202, Method 213, Condition I NoteThe above characteristics are typical but may not apply to all connectors. 3
R SMA Series Cable Connectors Straight Cable Plugs (male) for semi-rigid cables ANO 2111-2060.047/50 (SMT680-047) Gold Solder AI 01 11.2 [.441] for semi-rigid cables ANO 2111-2055.083/.085/50 (SMT680-086/RG405) Gold Solder AI 01 10.6 [.417] for semi-rigid cables ANO 2111-2058.141/50 (SMT680-141/RG402) Gold Solder AI 01 11.2 [.441] for flexible cables ANO 2111-2066 2/50/S (RG178) Nickel Solder AI 02 15.9 [.626] 4
ANO 2111-2028 2.6/50/S/D (RG316/LMR100) Gold Crimp AI 03 21.8 [.858] for flexible cables ANO 2111-2001 5/50/S/D (RG58/LMR195) Nickel Crimp AI 03 23.9 [.941] for flexible cables ANO 2111-2006 6/50 /D (LMR240) Albaloy Crimp AI 03 24.2 [.954] for flexible cables ANO 2111-2063 7.5/50 /D (LMR300) Nickel Crimp AI 03 24.9 [.980] 5
for flexible cables ANO 2111-2003 10.5/50 /D (LMR400) Nickel Crimp AI 03 28.6 [1.126] for flexible cables ANO 2111-2050 5/50/D (RG142) Gold Crimp AI 03 25.2 [.992] SW 9 [.354 AF.] Right Angle Cable Plugs (male) for flexible cables ANO 2121-2002 2/50/S (RG178) Gold Solder AI 04 16.5 [.650] 6.7 [.264] 6.5 [.256 SQ.] 11.1 [.437] 13.15 [.518] 6
for flexible cables ANO 2121-2005 2.6/50/S/D (RG316/LMR100) Gold Crimp AI 05 16.5 [.650] 6.7 [.264] 6.5 [.256 SQ.] 16.5 [.650] for flexible cables 13.15 [.518] ANO 2121-2004 5/50/S/D (RG58/LMR195) Gold Crimp AI 06 16 [.630] 6.5 [.256 SQ.] 6.5 [.256] 19.2 [.756] for flexible cables 12.75 [.502] ANO 2121-2007 6/50 /D (LMR240) Albaloy Crimp AI 07 17.8 [.701] 8 [.315 SQ.] 8 [.315] 21 [.827] 13.8 [.543] 7
Straight Cable Jacks (female) for semi-rigid cables ANO 2112-2061.047/50 (SMT680-047) Gold Solder AI 01 11.0 [.433] 8.40 [.331 DIA.] for semi-rigid cables ANO 2112-2056.083/.085/50 (SMT680-086/RG405) Gold Solder AI 01 11.0 [.433] 8.40 [.331 DIA.] for semi-rigid cables ANO 2112-2032.141/50 (SMT680-141/RG402) Gold Solder AI 01 11.0 [.433] 8.40 [.331 DIA.] for flexible cables ANO 2114-2041 5/50/D (LMR200) Gold Crimp AI 03 23.2 [.913] 7 [.276 DIA.] 8
for flexible cables ANO 2112-2064 7.5/50 /D (LMR300) Gold Crimp AI 03 9.60 [.378 DIA.] 24.5 [.965] for flexible cables /Mounting Hole ANO 2112-1012 2/50/S (RG178) Gold Solder AI 02/MH 3 19 [.748] 11.4 [.449 MAX. 2.5 [MAX..098] 2 [.078] 10.4 [.409 DIA.] for flexible cables /Mounting Hole ANO 2112-1014 2.6/50/S/D (RG316/LMR100) Gold Crimp AI 03/MH 3 ANO 2112-1023 2.6/50/S/D (RG316/LMR100) Gold Crimp AI 03/MH 3 11.4 [.449 23.5 [.928] MAX. 2.5 [MAX..098] 2 [.078] 10.4 [.409 DIA.] 9
Straight Bulkhead Cable Jacks (female) for semi-rigid cables /Mounting Hole ANO 2112-1062.047/50 (SMT680-047) Gold Solder AI 01/MH 3 15 [.591] 11.5 [.453] MAX. 2.5 [MAX..098] 2 [.079] 10.40 [.409 DIA.] for semi-rigid cables SW 11.1 [.437 HEX.] /Mounting Hole ANO 2112-1057.083/.085/50 (SMT680-086/RG405) Gold Solder AI 01/MH 3 15 [.591] 11.5 [.453] MAX. 2.5 [MAX..098] 2 [.079] 10.40 [.409 DIA.] SW 11.1 [.437 HEX.] for semi-rigid cables /Mounting Hole ANO 2112-1022.083/.085/50 (RG405) Gold Solder AI 01/MH 3 15.7 [.618] 10.5 [.413] 2.2 [.087] MAX. 2.5 [MAX..098] 10.40 [.409 DIA.] SW 11.1 [.437 HEX.] 10
for semi-rigid cables /Mounting Hole ANO 2112-1059.141/50 (SMT680-141/RG402) Gold Solder AI 01/MH 3 15 [.591] 11.5 [.453] MAX. 2.5 [MAX..098] 2 [.079] 10.40 [.409 DIA.] SW 11.1 [.437 HEX.] PCB Connectors Straight PCB jacks (female) ANO 2112-4015 Gold MH 22 5/8-24UNEF-2A 21.4 [.843] 8.6 [.338] 2 [.079] 18.3 [.720 SQ.] 2.1 [.083 DIA.] 1 [.039 DIA.] 25 [.984 SQ.] 4-3.5 [.138 DIA.] 4-2.5 [.098 DIA.] 2.1 [.083 DIA.] SW 19 [.748 HEX.] MAX. 2.5 [MAX..098] 25 [.984 SQ.] 11
R SMA Series Straight PCB jacks (female) ANO 2112-4019 Gold MH 16 17.5 [.689] 10.9 [.429] 21.5 [.846] 4.10 [.161 DIA.] 1.27 [.050 DIA.] 5.08 [.200 SQ.] MAX. 2.5 [MAX..098] 9.52 [.375 SQ.] 4-1 [.039 SQ.] Straight PCB jacks (female) ANO 2112-4034 Gold MH 3 17 [.669] 0.76 [.30 DIA] 11.4 [.449] MAX. [MAX..118] 3.8 [.150] Body and Contact 1.8 [.071] 5 [.197] 6.5 [.256] 1 [.039] 1 [.039] 6.5 [.256] Straight PCB jacks (female) Part No. Finish Fig. ANO 2112-4016 Gold 1 ANO 2112-4065 Gold 2 6.4 [.252] 14.3 [.563] 9.52 [.375] 1.02 [.040] 9.52 [.375] 7.92 [.312] 14.3 [.563] 9.55 [.376] 1.02 [.040 DIA.] 1.85 [.073 DIA.] 1.73 [.068] 9.52 [.375] 7.92 [.312] 1.85 [.073] 1.9 [.075] 1.02 [.040] 1.02 [.040] Fig. 1 Fig 2 12
Straight PCB jacks (female) ANO 2112-4038 Gold MH 16 13.5 [.531] 10 [.394] 9.5 [.374] 1.27 [.050 DIA.] 6.5 [.256 SQ.] 5.08 [.200 SQ.] 0.9 [.035 SQ.] Right angle PCB jacks (female) ANO 2122-4049 Gold MH 21 13.34 [.525] 6.35 [.250] 7.1 [.280 SQ.] 3.9 [.154 SQ.] 5.07 [.200] 8.25 [.325] 10.25 [.404] 4-1.6 [.063 SQ.] 1.27 [.050 DIA.] Panel Receptacles Receptacles, jack (female) ANO 2112-5051 Passivated MH 2 9.5 [.374] 1.27 [.050] 3 [.118] 0.50 [.020 DIA.] 1.27 [.050 DIA.] 5.25 [.207 DIA.] 13
Receptacles, jack (female) ANO 2112-5054 Passivated MH 3 12.6 [.496] 10 [.394] 1.80 [.071 DIA.] Receptacles, jack (female) ANO 2112-5021 Gold MH 3 12.7 [.500] 16.7 [.657] 1.6 [.063] 1.92 [.076] 1.27 [.050 DIA.] 4.12 [.162 DIA.] Receptacles, jack (female) ANO 2112-3042 Gold MH 4 20 [.787] 1.27 [.050 DIA.] 3/8-32UNEF-2A SW 12 [.472 HEX.] Receptacles, jack (female) ANO 2112-3026 Gold MH 3 10.40 [.409 DIA.] 14 [.551] 11 [.433] MAX. 2.5 [MAX..098] 1.7 [.067] 1.27 [.050 DIA.] 14
Receptacles, jack (female) ANO 2112-3030 Passivated MH 6 9.52 [.375] 1.7 [.067] 27.52 [1.083] 18 [.709] 15 [.591] 1.27 [.050 DIA.] 4.12 [.162 DIA.] 12.7 [.500 SQ.] 8.64 [.340 SQ.] 4-2.60 [.102 DIA.] Receptacles, jack (female) Fig. ANO 2112-3035 Passivated MH 12 1 ANO 2112-3036 Passivated MH 10 2 9.5 [.374] 27.4 [1.079] 17.9 [.705] 1.65 [.065] 15 [.591] 1.27 [.050 DIA.] 4.10 [.161 DIA.] 17.5 [.689 SQ.] 12.7 [.500 SQ.] 4-3.20 [.126 DIA.] Fig. 1 9.5 [.374] 27.4 [1.079] 1.65 [.065] 17.9 [.705] 15 [.591] 1.27 [.050 DIA.] 5.7 [.224] 15.88 [.625] 12.2 [.480] 2-2.60 [.102 DIA.] 4.10 [.161 DIA.] Fig. 2 Receptacles, jack (female) ANO 2112-3020 Gold MH 6 9.52 [.375] 20.37 [.802] 10.85 1.7 [.427] [.067] 8.25 [.325] 1.27 [.050 DIA.] 12.7 [.500 SQ.] 8.64 [.340 SQ.] 4.12 [.162 DIA.] 4-2.60 [.102 DIA.] 15
Receptacles, jack (female) ANO 2112-3045 Gold MH 14 9.8 [.386] 2 [.079] 39.7 [1.563] 10.00 [.394 DIA.] 120 6.00 [.236 DIA.] 1.50 [.059 DIA.] 3-2.10 [.083 DIA.] 14.00 [.551 DIA.] Receptacles, jack (female) ANO 2112-3046 Gold MH 15 9.8 [.386] 2.3 [.091] 33 [1.299] 60 6-2.30 [.090 DIA.] 9.00 [.354 DIA.] 2.00 [.079 DIA.] 28.90 [1.138 DIA.] 16.00 [.630 DIA.] 24.80 [.976 DIA.] Receptacles, jack (female) Fig. ANO 2112-3024 Passivated MH 6 1 ANO 2112-3031 Passivated MH 10 2 9.55 [.376] 1.65 [.065] 0.45 [.018 DIA.] Deep 2 [.079] 2.74 [.108 DIA.] 0.07 [.003] 4.60 [.181 DIA.] 12.7 [.500 SQ.] 8.64 [.340 SQ.] 4-2.60 [.102 DIA.] 9.55 [.376] 1.65 [.065] 0.45 [.018 DIA.] Deep 2 [.079] 2.74 [.108 DIA.] 0.07 [.003] 4.60 [.181 DIA.] 12.2 [.480] 5.6 [.220] 2.34 [.092 DIA.] 15.88 [.625] Fig. 1 Fig. 2 16
Receptacles, jack (female) ANO 2112-3068 Gold MH 10 16 [.630] 9.6 [.378] 1.5 [.059] 6 [.236] 12.2 [.480] 2-2.60 [.102 DIA.] Flat tab receptacles, jack (female) ANO 2112-3029 Passivated MH 11 12 [.472] 9.5 [.374] 1.65 [.065] 0.12 [.005] 9.5 [.374 SQ.] 6.35 [.250 SQ.] 2.5 [.098] 1.27 [.050 DIA.] 4-2.20 [.087 DIA.] Slot receptacles, jack (female) ANO 2112-3039 Passivated MH 6 9.52 [.375] 1.65 [.065] 0.3 [.012] 1.27 [.050] 12.7 [.500 SQ.] 8.64 [.340 SQ.] 4-2.60 [.102 DIA.] 1.27 [.050 DIA.] 17
Adapter Connectors Adapter plug/plug (male/male) ANO 211-211-1007 Gold SMA(plug) / SMA(plug) 21.7 [.854] Adapter plug/plug (male/male) ANO 211-261-1029 Gold/Albaloy SMA(plug) / QMA(plug) 32.05 [1.262] 7.8 [.307 DIA.] 11.5 [.453 DIA.] Adapter plug/plug (male/male) ANO 211-281-1051 Gold/Albaloy SMA(plug) /Mini-QMA(plug) 26.5 [1.043] 7.8 [.307 DIA.] 11.5 [.453 DIA.] Adapter plug/plug (male/male) ANO 211-531-1040 Nickel SMA(plug) / HPQN(plug) 18 [.709 DIA.] 7.8 [.307 DIA.] 37.7 [1.484] 18
Adapter jack/jack (female/female) ANO 212-512-1025 Gold SMA(jack) /SMA(jack) 14 [.551] Adapter jack/jack (female/female) ANO 212-512-1025 Nickel SMA(jack) / N (jack) 31 [1.221] 5/8-24UNEF-2A Adapter jack/jack (female/female) ANO 212-262-1030 Gold/Albaloy SMA(jack) / QMA (jack) 22 [.862] 5.55 [.219] 5.56 [.219 DIA.] Adapter jack/jack (female/female) ANO 212-282-1052 Gold/Albaloy SMA(jack) / Mini-QMA (jack) 17.9 [.705] 4 [.157] 5.56 [.219 DIA.] 19
Adapter jack/jack (female/female) ANO 212-532-1041 Nickel SMA(jack) / HPQN (jack) 28.5 [1.122] 5 [.197] 12 [.472 DIA.] 10 [.394 DIA.] Adapter jack/jack (female/female) Mounting Hole ANO 212-212-1004 Gold SMA(jack) /SMA (jack) MH 3 22.2 [.874] 14.6 [.575] MAX. 6.1 [MAX..240] 1.7 [.067] 10 [.394 DIA.] SW 9.5 [.374 HEX.] Adapter jack/jack (female/female) Mounting Hole ANO 212-214-1005 Gold SMA(jack) /SMA-RP(jack) MH 3 19 [.748] 10 [.394] MAX. 1.5 [MAX..059] 2 [.079] 10.4 [.409 DIA.] 20
Bulkhead Adapter jack/jack (female/female) Mounting Hole ANO 212-212-1009 Gold SMA(jack) /SMA (jack) MH 3 19 [.748] 10 [.394] MAX. 1.5 [MAX..060] 2 [.079] 10.4 [.409 DIA.] SW 11 [.433 HEX.] Bulkhead Adapter jack/jack (female/female) Mounting Hole ANO 212-312-1002 Nickel SMA(jack) /BNC(jack) MH 23 3.0 [0.118] 9.0 [0.354] 33.6 [1.323] 21.6 [0.850] MAX. 5 [MAX..197 ] 1/2-28UNEF-2A Bulkhead Adapter jack/jack (female/female) Mounting Hole ANO 212-512-1003 Nickel SMA(jack) /N(jack) MH 24 2.8 [.110] 31.5 [1.240] 22.0 [.866] MAX. 7 [MAX..276] 22.0 [.866 DIA.] 5/8-24UNEF-2A SW 19 [.748 HEX.] 21
Adapter plug/jack (male/female) ANO 212-511-1024 Nickel SMA(jack) / N(plug) 32.5 [1.280] 20 [.787 DIA.] Adapter plug/jack (male/female) ANO 211-334-1006 Nickel SMA (plug) / TNC-RP (jack) 26.8 [1.055] 7/16-28UNEF-2A Adapter plug/jack (male/female) ANO 211-182-1003 Tin SMA (plug) / UFL (jack) 12.6 [.496] 2 [.079 DIA.] Adapter plug/jack (male/female) ANO 211-332-1020 Nickel SMA (plug) / TNC (jack) 26.8 [1.055] 7/16-28UNEF-2A 22
Adapter plug/jack (male/female) ANO 212-361-1023 Nickel SMA (jack) / TM (plug) 24 [.945] 11 [.433 DIA.] Adapter plug/jack (male/female) ANO 212-261-1031 Gold/Albaloy SMA (jack) / QMA (plug) 31 [1.220] 11.5 [.453 DIA.] Adapter plug/jack (male/female) ANO 211-262-1032 Gold/Albaloy SMA(plug) / QMA (jack) 7.8 [.307 DIA.] 23 [.906] 5.55 [.219] 5.56 [.219 DIA.] Adapter plug/jack (male/female) ANO 212-281-1053 Gold/Albaloy SMA (jack) / Mini-QMA (plug) 25.4 [1.000] 11.5 [.453 DIA.] 23
Adapter plug/jack (male/female) ANO 211-282-1054 Gold/Albaloy SMA(plug) / Mini-QMA (jack) 7.8 [.307 DIA.] 19 [.748] 4 [.157] 5.56 [.219 DIA.] Adapter plug/jack (male/female) ANO 212-531-1042 Nickel SMA (jack) / HPQN (plug) 36.6 [1.441] 18 [.709 DIA.] Adapter plug/jack (male/female) ANO 211-532-1043 Nickel SMA(plug) / HPQN (jack) 5 [.197] 10 [.394 DIA.] 7.8 [.307 DIA.] 29.6 [1.165] 24
Termination Straight Plug (male) Part No. Finish Average Power Peak Power Frequency ANO 211-702 Nickel 1W 500W 0-18 GHz 16.9 [.665] SW 5.5 [.217 AF.] Straight Plug (male) Part No. Finish Average Power Peak Power Frequency ANO 211-703 Nickel 2W 500W 0-18 GHz 20.9 [.823] 12 [.472 DIA.] Straight Jack (female) 11.5 [.453] SW 5.5 [.217 AF.] Part No. Finish Average Power Peak Power Frequency ANO 212-701 Nickel 2W 500W 0-6 GHz SW 6.3 [.248 HEX.] 25
Assembly Instruction AI 01 Stripping Length Part No. Cable Group (Example) a ANO 2111-2060 ANO 2112-2061 ANO 2112-1062 ANO 2112-1057.047/50 (SMT680-047) 2.5 2.5 ANO 2112-2056.083/.085/50 (SMT680-086/RG405) ANO 2111-2055 3.0 ANO 2112-1022 ANO 2111-2058 3.0 ANO 2111-2067.141/50 (SMT680-141/RG402) 2.2 ANO 2112-2032 2.5 ANO 2112-1059 a solder 1.1 Strip the cable. 1.2 Slide on center contact until it bottoms against cable dielectrique. 1.3 Solder center contact. 1.4 Clean soldering area. 2.1 Slide the cable into the body until it bttoms against insulator. solder 3.1 Solder the body onto the cable. 3.2 Clean soldering area. 26
AI 02 Stripping Length Part No. Cable Group (Example) a b c ANO 2111-2066 2.0 2.0 5.0 2/50/S (RG178) ANO 2112-1012 3.0 1.5 8.1 heatshrink sleeve c b a solder 1.1 Slide onto the cable the heatshrink sleeve. 1.2 Strip the cable. 1.3 Slide on center contact until it bottoms against cable dielectrique. 1.4 Solder center contact. 2.1 Slide the cable into the body until it bottoms against insulator. solder 3.1 Solder the body onto the cable. 3.2 Clean soldering area. Shrink the heatshrink sleeve 4.1 Slide sleeve over soldering area and heatshrink in place. 27
AI 03 Stripping Length Part No. Cable Group (Example) a b c ANO 2111-2028 2.5 2.5 5.5 2.6/50/S/D (RG316/LMR100) ANO 2111-2008 2.0 2.0 6.0 ANO 2111-2001 5/50/S/D (RG58/LMR195) 2.5 7.5 8.0 ANO 2111-2006 6/50 /D (LMR240) 2.5 5.7 8.0 ANO 2111-2063 7.5/50 /D (LMR300) 3.0 1.0 6.0 ANO 2112-2064 ANO 2111-2003 10.5/50 /D (LMR400) 4.0 7.5 10.5 ANO 2111-2050 5/50/D (RG142) 4.0 0 7.0 ANO 2114-2041 5/50/D (LMR200) 2.3 7.2 8.0 ANO 2112-1014 2.6/50/S/D (RG316/LMR100) 3.0 2.8 6.0 ANO 2112-1023 3.0 1.9 6.0 c b a 1.1 Slide onto the cable the heatshrink sleeve and the ferrule. 1.2 Strip the cable. solder 2.1 Slide on center contact until it bottoms against cable dielectrique. 2.2 Solder center contact. 2.3 Clean soldering area. FERRULE F Shrink the heatshrink sleeve 3.1 Fan the braid. 3.2 Slide the cable into the body until it bottoms against insulator. 3.3 Slide the ferrule over the braid. (In direction F) 4.1 Cut the excess of braid. 4.2 Crimp the ferrule. 4.3 Slide sleeve over ferrule and heatshrink in place. 28
AI 04 Stripping Length Part No. Cable Group (Example) a b c ANO 2121-2002 2/50/S (RG178) 1.0 2.0 6.2 heatshrink sleeve c b a 1.1 Slide onto the cable the heatshrink sleeve. 1.2 Strip the cable. solder solder 2.1 Slide the cable into the body 2.2 solder inner conductor. 2.3 Solder the body onto the cable. nut insulator 3.1 Slide sleeve over soldering area and heatshrink in place. 3.2 Mount the insultor. 3.3 screw the nut into the body. 29
AI 05 Stripping Length Part No. Cable Group (Example) a b c ANO 2121-2005 2.6/50/S/D (RG316/LMR100) 1.0 2.2 6.0 c b a 1.1 Slide onto the cable the heatshrink sleeve and the ferrule. 1.2 Strip the cable. ferrule solder 2.1 Fan the braid. 2.2 Push connector body under the braid. 2.3 Solder inner conductor. 2.4 Slide the ferrule over the braid. Shrink the heatshrink sleeve 3.1 Cut the excess of braid. 3.2 Crimp th e ferrule. 3.3 Slide sleeve over ferrule and heatshrink in place. nut insulator 4.1 Mount the insultor. 4.2 Screw the nut into the body. 30
AI 06 Stripping Length Part No. Cable Group (Example) a b c ANO 2121-2004 5/50/S/D (RG58/LMR195) 1.7 3.6 7.7 c b a 1.1 Slide onto the cable the heatshrink sleeve and the ferrule. 1.2 Strip the cable. ferrule solder 2.1 Fan the braid. 2.2 Push connector body under the braid. 2.3 Solder inner conductor. 2.4 Slide the ferrule over the braid. Shrink the heatshrink sleeve 3.1 Cut the excess of braid. 3.2 Crimp the ferrule. 3.3 Slide sleeve over ferrule and heatshrink in place. nut 4.1 Screw the nut into the body. 31
AI 07 Stripping Length Part No. Cable Group (Example) a b c ANO 2121-2007 6/50 /D (LMR240) 2.5 3.0 8.0 c b a 1.1 Slide onto the cable the heatshrink sleeve and the ferrule. 1.2 Strip the cable. ferrule solder 2.1 Fan the braid. 2.2 Push connector body under the braid. 2.3 solder inner conductor. 2.4 Slide the ferrule over the braid. Shrink the heatshrink sleeve 3.1 Cut the excess of braid. 3.2 Crimp the ferrule. 3.3 Slide sleeve over ferrule and heatshrink in place. press on 4.1 Place the cap. 4.2 Press cap flush or slightly below surface of body assembly. 32