Servo-electric 2-finger parallel gripper WSG 32

Translation of the original manual Servo-electric 2-finger parallel gripper WSG 32 Assembly and Operating Manual Superior Clamping and Gripping

Imprint Copyright: Imprint This manual is protected by copyright. The author is SCHUNK GmbH & Co. KG. All rights reserved. Any reproduction, processing, distribution (making available to third parties), translation or other usage - even excerpts - of the manual is especially prohibited and requires our written approval. Technical changes: We reserve the right to make alterations for the purpose of technical improvement. Document number: 0389575 Version: 03.00 28/08/2017 en SCHUNK GmbH & Co. KG All rights reserved. Dear Customer, thank you for trusting our products and our family-owned company, the leading technology supplier of robots and production machines. Our team is always available to answer any questions on this product and other solutions. Ask us questions and challenge us. We will find a solution! Best regards, Your SCHUNK team SCHUNK GmbH & Co. KG Spann- und Greiftechnik Bahnhofstr. 106 134 D-74348 Lauffen/Neckar Tel. +49-7133-103-0 Fax +49-7133-103-2399 info@de.schunk.com schunk.com 2 03.00 WSG 32 en

Table of contents Table of contents 1 General... 6 1.1 About this manual... 6 1.1.1 Presentation of Warning Labels... 6 1.1.2 Applicable documents... 7 1.2 Warranty... 7 1.3 Scope of delivery... 8 1.4 Accessories... 8 2 Basic safety notes... 9 2.1 Intended use... 9 2.2 Not intended use... 9 2.3 Constructional changes... 9 2.4 Special standards... 10 2.5 Spare parts... 10 2.6 Gripper fingers... 10 2.7 Environmental and operating conditions... 11 2.8 Personnel qualification... 11 2.9 Personal protective equipment... 12 2.10 Notes on safe operation... 12 2.11 Transport... 13 2.12 Malfunctions... 13 2.13 Disposal... 13 2.14 Fundamental dangers... 14 2.15 Notes on particular risks... 14 3 Technical data... 16 3.1 Outer dimensions... 16 3.2 Nominal mechanical data... 17 3.2.1 Permitted finger load... 19 3.2.2 Gripping force... 19 3.3 Nominal electrical data... 22 3.3.1 Fuse... 22 3.4 Interfaces and connections... 23 3.4.1 Power supply and CAN-Bus (option)... 23 3.4.2 Ethernet... 24 3.4.3 CAN-Bus (optional)... 25 3.4.4 Base jaw with a sensor port... 26 3.5 Name plate... 28 03.00 WSG 32 en 3

Table of contents 4 Design and description... 29 4.1 Design... 29 4.2 Description... 30 5 Assembly... 31 5.1 Safety notes... 31 5.2 Mechanical connection... 32 5.3 Electrical connection... 33 5.4 Installation of the fingers... 35 6 Start-up... 36 6.1 Initial commissioning... 36 6.2 Changing the IP address and using DHCP... 39 7 Operation... 40 7.1 Operating software... 41 7.2 Memory card... 41 7.3 The boot process... 42 7.4 Display of operating state... 42 7.5 Status word and gripper state... 44 7.5.1 Status word... 44 7.5.2 Gripper state... 45 7.6 Homing the product... 47 7.7 Gripping, detecting parts to be gripped and monitoring the gripping... 48 7.8 Software limit switch... 50 7.9 Fast stops requiring acknowledgment... 51 7.10 Log memory... 52 7.11 Thermal monitoring... 52 7.12 Monitoring the motor current... 53 7.13 Monitoring the supply voltage... 54 7.14 Configuration and diagnosis via the web interface... 55 7.14.1 Access restrictions for the web user interface... 57 7.15 Command interface... 58 7.16 Scripting... 58 7.17 Resetting the configuration... 59 7.18 Implementing the gripping process... 59 8 Maintenance and cleaning... 62 9 Troubleshooting... 63 9.1 The gripper jaws don't move... 63 9.2 Gripper stops abruptly... 63 4 03.00 WSG 32 en

Table of contents 9.3 No connection to the web interface... 64 10 Translation of original declaration of incorporation... 65 11 Annex to Declaration of Incorporation... 66 03.00 WSG 32 en 5

General 1 1.1 General About this manual This manual contains important information for a safe and appropriate use of the product. This manual is an integral part of the product and must be kept accessible for the personnel at all times. Before starting work, the personnel must have read and understood this operating manual. Prerequisite for safe working is the observance of all safety instructions in this manual. Illustrations in this manual are provided for basic understanding and may differ from the actual product design. In addition to these instructions, the documents listed under ( 1.1.2, Page 7) are applicable. 1.1.1 Presentation of Warning Labels To make risks clear, the following signal words and symbols are used for safety notes. DANGER Danger for persons! Non-observance will inevitably cause irreversible injury or death. WARNING Dangers for persons! Non-observance can lead to irreversible injury and even death. CAUTION Dangers for persons! Non-observance can cause minor injuries. NOTICE Material damage! Information about avoiding material damage. 6 03.00 WSG 32 en

General 1.1.2 Applicable documents General terms of business* Catalog data sheet of the purchased product * Assembly and operating manuals of the accessories * WSG Command Set Reference Manual - Description of the binary command protocol (TCP/IP, CAN-Bus) * WSG GCL Reference Manual Description of the text based command protocol (TCP/IP) * WSG Fieldbus Interface Manual - Description of the fieldbus interface (PROFINET, Modbus/TCP) * WSG Scripting Reference Manual - Description of the optional script interpreter for the gripper control system The documents marked with an asterisk (*) can be downloaded on our homepage schunk.com 1.2 Warranty If the product is used as intended, the warranty is valid for 24 months from the ex-works delivery date under the following conditions: Intented use in 1-shift operation Observe the specified maintenance and lubrication intervals Observe the ambient conditions and operating conditions Parts touching the workpiece and wear parts are not included in the warranty. The product is considered defective if its basic function "gripping" is no longer given. 03.00 WSG 32 en 7

General 1.3 Scope of delivery The scope of delivery includes Servo-electric 2-finger parallel gripperwsg 32 in the version ordered 3 m network cable M8 to RJ-45 CD with documentation and firmware 1.4 Accessories The following accessories, which must be ordered separately, are required for the product: Ethernet data cable, length 5 m, 10 m, 4-pole M8-connector straight, right angle to RJ-45, for WSG gripper Power supply cable length 5 m, shielded, 6-pole M8 connector straight, right angle to free wire ends Centering sleeves, Ø6.0x5.35, outer diameter 6h6 Universal finger ABF WSG32/50-GV Force measurement finger ABF WSG32/50-DV 8 03.00 WSG 32 en

Basic safety notes 2 2.1 Basic safety notes Intended use The product is designed exclusively for gripping and temporarily holding workpieces or objects. The product may only be used within the scope of its technical data, ( 3, Page 16). When implementing and operating components in safety-related parts of the control systems, the basic safety principles in accordance with DIN EN ISO 13849-2 apply. The proven safety principals in accordance with DIN EN ISO 13849-2 also apply to categories 1, 2, 3 and 4. The product is intended for installation in a machine/system. The applicable guidelines must be observed and complied with. The product is intended for industrial and industry-oriented use. Appropriate use of the product includes compliance with all instructions in this manual. 2.2 Not intended use It is not intended use if the product is used, for example, as a pressing tool, stamping tool, lifting gear, guide for tools, cutting tool, clamping device or a drilling tool. Any utilization that exceeds or differs from the appropriate use is regarded as misuse. 2.3 Constructional changes Implementation of structural changes By conversions, changes, and reworking, e.g. additional threads, holes, or safety devices can impair the functioning or safety of the product or damage it. Structural changes should only be made with the written approval of SCHUNK. 03.00 WSG 32 en 9

Basic safety notes 2.4 Special standards The following standards are met: Fast transients on supply and I/O lines (burst) to IEC / EN 61000-4-4 HF power supply to IEC/EN 61000-4-6 HF radiation according to IEC/EN 61000-4-3 Emissions according to EN 55011:2009 Class A (corresponds to EN 61000-6-4:2007) Magnetic field with energy technical frequency according to EN 61000-4-8 2.5 Spare parts Use of unauthorised spare parts Using unauthorised spare parts can endanger personnel and damage the product or cause it to malfunction. Use only original spare parts or spares authorised by SCHUNK. 2.6 Gripper fingers Requirements for the gripper fingers Stored energy within the product creates the risk of serious injuries and significant property damage. Arrange the gripper fingers in a way that the product reaches either the position "open" or "closed" in a de-energized state. Only exchange the gripper fingers when no residual energy remains in the product. Make sure that the product and the top jaws are a sufficient size for the application. 10 03.00 WSG 32 en

Basic safety notes 2.7 Environmental and operating conditions Required ambient conditions and operating conditions Incorrect ambient and operating conditions can make the product unsafe, leading to the risk of serious injuries, considerable material damage and/or a significant reduction to the product's life span. Make sure that the product is used only in the context of its defined application parameters, ( 3, Page 16). Observe Maintenance intervals, ( 8, Page 62). Make sure that the environment is clean and the ambient temperature corresponds to the specifications per the catalog. 2.8 Personnel qualification Inadequate qualifications of the personnel If the personnel working with the product is not sufficiently qualified, the result may be serious injuries and significant property damage. All work may only be performed by qualified personnel. Before working with the product, the personnel must have read and understood the complete assembly and operating manual. Observe the national safety regulations and rules and general safety instructions. Trained electrician Qualified personnel Instructed person Service personnel of the manufacturer The following personal qualifications are necessary for the various activities related to the product: Due to their technical training, knowledge and experience, trained electricians are able to work on electrical systems, recognize and avoid possible dangers and know the relevant standards and regulations. Due to its technical training, knowledge and experience, qualified personnel is able to perform the delegated tasks, recognize and avoid possible dangers and knows the relevant standards and regulations. Instructed persons were instructed by the operator about the delegated tasks and possible dangers due to improper behaviour. Due to its technical training, knowledge and experience, service personnel of the manufacturer is able to perform the delegated tasks and to recognize and avoid possible dangers. 03.00 WSG 32 en 11

Basic safety notes 2.9 Personal protective equipment Using personal protective equipment Not wearing personal protective equipment while working with the product, may result in dangers that impact the personnel's safety and health. While working with the product, observe the health and safety regulations and wear the required personal safety equipment. Observe the valid safety and accident prevention regulations. In case of sharp edges and corners and rough surfaces, wear protection gloves. In case of hot surfaces, wear heat-resistant protection gloves. When dealing with hazardous substances, wear protection gloves and goggles. In case of moving parts, wear tight protection clothes. 2.10 Notes on safe operation Incorrect handling of the personnel Incorrect handling and assembly may impair the product's safety and cause serious injuries and considerable material damage. Avoid any manner of working that may interfere with the function and operational safety of the product. Use the product as intended. Observe the safety notes and assembly instructions. Do not expose the product to any corrosive media. This does not apply to products that are designed for special environments. Eliminate any malfunction immediately. Observe the care and maintenance instructions. Observe the current safety, accident prevention and environmental protection regulations regarding the product's application field. 12 03.00 WSG 32 en

Basic safety notes 2.11 Transport Handling during transport Incorrect handling during transport may impair the product's safety and cause serious injuries and considerable material damage. When handling heavy weights, use lifting equipment to lift the product and transport it by appropriate means. Secure the product against falling during transportation and handling. Stand clear of suspended loads. 2.12 Malfunctions Behavior in case of malfunctions Immediately remove the product from operation and report the malfunction to the responsible departments/persons. Order appropriately trained personnel to rectify the malfunction. Do not recommission the product until the malfunction has been rectified. Test the product after a malfunction to establish whether it still functions properly and no increased risks have arisen. 2.13 Disposal Handling of disposal The incorrect handling of disposal may impair the product's safety and cause serious injuries as well as considerable material and environmental harm. Follow local regulations on dispatching product components for recycling or proper disposal. 03.00 WSG 32 en 13

Basic safety notes 2.14 Fundamental dangers General Observe safety distances. Never deactivate safety devices. Before commissioning the product, take appropriate protective measures to secure the danger zone. Disconnect power sources before installation, modification, maintenance, or calibration. Ensure that no residual energy remains in the system. If the energy supply is connected, do not move any parts by hand. Do not reach into the open mechanism or movement area of the product during operation. 2.15 Notes on particular risks WARNING Risk of injury from objects falling and being ejected! Falling and ejected objects during operation can lead to serious injury or death. Take appropriate protective measures to secure the danger zone. WARNING Risk of injury from crushing and impacts! Serious injury could occur during the base jaw procedure and when breaking or loosening the gripper fingers. Wear suitable protective equipment. Do not reach into the open mechanism or the movement area of the product. 14 03.00 WSG 32 en

WARNING Basic safety notes Risk of injury due to unexpected movements! If the power supply is switched on or residual energy remains in the system, components can move unexpectedly and cause serious injuries. Before starting any work on the product: Switch off the power supply and secure against restarting. Ensure that no residual energy remains in the system. 03.00 WSG 32 en 15

Technical data 3 3.1 Technical data Outer dimensions Outer dimensions 16 03.00 WSG 32 en

Technical data 3.2 Nominal mechanical data NOTICE Exceeding the specified nominal data can damage the product. If in doubt, please discuss your application with SCHUNK. Mechanical operating data value Note Stroke per finger [mm] 34 Nominal gripping force [N] 50 Grip force approximation via motor current Min.Gripping force [N] 5 Gripping speed 5 mm/s, finger length 55 mm, steel on steel Max.Gripping force [N] 50 Gripping speed 50 mm/s, finger length 55 mm, steel on steel Weight [kg] 0.55 Recommended workpiece weight [kg] 0.5 Max. permissible finger length [mm] 120 at nominal force, see following figure "Determining the clamping height" Max. permitted weight per finger [kg] 0.1 IP rating 40 DIN EN 60529 Ambient temperature [ C] Min. Max. Air humidity [%] Min. Max. 0 50 0 90 non condensing Repeatability [mm] ±0.005 3σ-divergence Gripping speed [mm/s] Min. Max. Finger acceleration [mm/s 2 ] Min. Max. 5 400 100 5000 03.00 WSG 32 en 17

Technical data Determining the clamping height Typical finger acceleration, gripping force: 50 N, finger mass: 2x 0.1 kg 18 03.00 WSG 32 en

Technical data 3.2.1 Permitted finger load The following table shows the permitted load of the finger. The specified load may be applied simultaneously and in addition to the gripping force. Mechanical Load Value Fz [N], max. 50 Mx [Nm], max. 1.6 My [N], max. 1.6 Mz [N], max. 1 Finger load 3.2.2 Gripping force The gripping force of the product is defined as the effective force acting between the fingers multiplied by the number of fingers in contact with the part to be grasped. To operate the gripping product without force measurement fingers, the gripping force is calibrated during the manufacturing process. The actual gripping force depends on gripping speed, finger length and temperature. Following figure "Recommended gripping speed" shows the recommended gripping speed according to the desired gripping force. The typical influence of the finger to the effective gripping force is shown in following "Gripping force over clamping height diagram". NOTE For a precise control of the gripping force use the Force Measurement Finger ABF WSG32/50-DV (available as an accessory) 03.00 WSG 32 en 19

Technical data Recommended gripping speed (steel on steel, finger length: 55 mm) NOTE The diagram above is considered as a recommendation. If in doubt, please try out and measure the actual force for your application. Gripping force in dependency of the finger length (exemplary) Definition of the nominal gripping force To determine the nominal gripping force, the product is nonpositively mounted to an aluminum plate, see following figure. The plate itself is thermally insulated from the underlying surface. With an ambient temperature of 22 C the product can hold with the nominal gripping force for at least 5 hours. 20 03.00 WSG 32 en

Technical data Arrangement for ascertaining the nominal gripping force NOTICE For high gripping forces or long holding cycles, make sure that heat is well dissipated via the screw contact surface. Damage to the product is possible! 03.00 WSG 32 en 21

Technical data 3.3 Nominal electrical data NOTICE Exceeding the specified nominal data can damage the product. If in doubt, please discuss your application with SCHUNK. Electrical operating data value Note Clamping voltage [V DC] Min. Typical Max. 22 24 28 Currend drawn when idle [A] 0.05 Current drawn when holding [A] 0.75 Gripping force = 50N Positioning resolution [μm] 1.3 Controller Integrated Command interface Ethernet CAN-Bus (optional) PROFINET (optional) Configuration interface web based 3.3.1 Fuse The product has an integrated fuse to protect against short circuits and incorrect polarity. To have the fuse changed, please contact SCHUNK (Tel. +49 7133-103-2333). 22 03.00 WSG 32 en

Technical data 3.4 Interfaces and connections The product has different interfaces for controlling. The selection of the communication interface goes on via the web-surface ( 7.14, Page 55). 3.4.1 Power supply and CAN-Bus (option) Power is supplied via a 6-way M8 connector on the product's housing, which also carries the optional CAN-Bus interface. CAN-Bus can be used for commands. The CAN-Bus interface is not electrically isolated and uses the product s GND pin as reference potential. Terminal assignment of the power supply and CAN-Bus connector Requirement for the power supply: Power supply: 24 V DC ±10% Ripple < 150 mvss Available output current: at least 3 A The following cables are suitable to connect the power supply: Type: KA GLN0806-LK-00500-A Power cable, length 5, 6 pole M8 connector straight to RJ-45, Ident-No. 0307787 Type: KA WLN0806-LK-00500-A Power cable, length 5m, 6 pole M8 connector angle to RJ-45, Ident-No. 0307785 03.00 WSG 32 en 23

Technical data 3.4.2 Ethernet The Ethernet interface can be used both for commands as well as for configuration via the integrated web server. It is presented via a 4- way M8 connector (socket). Pin assignment of the Ethernet connector (view on the socket). The following cables are suitable to connect the Ethernet interface: Type: KA GGN0804-PG-00300-R Ethernet cable, length 3m, 4 pole M8 connector straight to RJ-45, Ident-No. 0349620 Type: KA GGN0804-PG-00500-R Ethernet cable, length 5m, 4 pole M8 connector angle to RJ-45, Ident-No. 0349621 Commands are sent to the product via TCP/IP connections, using the TCP or UDP protocol. For further information, please see the "WSG Command Set Reference Manual" (on the accompanying CD or can be called up via the web interface). The product currently also supports the following network services: DHCP (dynamic IP addresses) SNTP (network time) HTTP (web user interface) DNS (resolution of host names) mdns (decentralized resolution of host names) 24 03.00 WSG 32 en

Technical data Interface specification: parameter value Note Transmission standard IEEE 802.3 Communication standard TCP/IP (IPv4) Transmission speed [MBit/s] 10; 100 Auto-Negotiated Transmission type Half duplex Auto-MDIX yes 3.4.3 CAN-Bus (optional) The product is available with an optional CAN-Bus interface. It is connected using the connector of the power supply,( 3.4.1, Page 23). Interface specification CAN-Bus (option): parameter value Note Bus Standard CAN 2.0A, CAN 2.0B Supported bit rates [kbit/s] 10; 20; 50; 100; 125; 250; 500; 1000 Voltage CAN-L and CAN-H [V] Min. Max. Input resistance CAN-L and CAN-H [kω] Min. Max. Differential input resistance Min. Max. -7 12 20 50 40 100 Connecting the product to CAN-Bus relative to GND CAN networks must have a defined termination at the first and last participant of the bus. The product comes with a factory-set optional termination. For this purpose, please contact the technical sales of SCHUNK. NOTE There is no electrical isolation on the CAN-Bus! 03.00 WSG 32 en 25

Technical data 3.4.4 Base jaw with a sensor port The product has an integrated sensor port in each of the base jaws which makes it easy to connect intelligent gripper fingers. The sensor port makes the following interfaces available: UART (LVTTL Levels) SPI (LVTTLlevels) Digital I/O pin (LVTTL levels) The sensor port supports the automatic configuration of the connected fingers. To use this function, a configuration memory must be integrated into the fingers. All of the intelligent fingers offered by SCHUNK for this gripper (e.g. force measurement finger) already have this memory integrated and are completely configured, so that you just have to fit this finger to the product. The fingers will then be automatically detected the next time the system starts. The sensor port supplies an operating voltage of 5 V ±10% at max. 200 ma. The supply voltage is protected against short circuits and can be switched on and off from the gripper control system. A short circuit in the supply voltage will trigger an error state which must be acknowledged. NOTE The power supply from the sensor port is not suitable to supply actuators. NOTICE The gripper control system may be destroyed by excess voltage on the sensor port pins! The digital pins on the sensor port are protected against electrostatic discharge. However, SCHUNK still recommends that you should not directly touch the pins on the connector with fingers, to avoid damage from electrostatic discharge. The SPI and UART digital interfaces share transmit and receive pins. The configuration memory determines which function is active. 26 03.00 WSG 32 en

Technical data Sensor port Should you require detailed specifications of the sensor port to implement your own fingers, please contact SCHUNK. Matching centering sleeves Matching centering sleeves are supplied with the fingers. For your own designs or as a spare part, please use the centering sleeves which are available as accessories, described as: centering sleeve Ø6.0 x 5.35 (outer diameter: 6h6). Sensorport connector type Manufacturer: ERNI, type: SMC-B-12 (terminal strip), part number: 154805 03.00 WSG 32 en 27

Technical data Counterpiece: SMC-Q-12 (male, low-profile connector), part number: 154818 Sensor port connector pin assignments Pin number Name Direction Function 1 MOSI/TXD OUT SPI/UART: Transmit data from the manual controller 2 nssel OUT Only SPI: A low signal selects the slave 3 DIO I/O Digital I/O pin 4 SCLK OUT Only SPI: Clock for transmit and receive data 5 CFG-SDA I/O Configuration bus data line 6 MISO/RXD IN SPI/UART: Received data 7 CFG-SCL OUT Configuration bus clock line 8 NC - not connected 9 +5V OUT Operating voltage output 5V/200mA max. 10 +5V 11 GND OUT Mass 12 GND 3.5 Name plate The name plate is on the narrow side of the product above the connector. It shows the type and the serial number of the product. 28 03.00 WSG 32 en

Design and description 4 4.1 Design and description Design Components and connections WSG 32 Item Designation 1 Base jaw 2 Sensorport 3 Display of operating status 4 Name plate 5 Ethernet-port 6 Power supply and CAN-Bus (opt.) 7 Button for configuration-reset 8 Memory card 9 Communikation-LEDs 10 Cover control tray 03.00 WSG 32 en 29

Design and description 4.2 Description The product is an electrical 2-Finger Compact Gripper with covered guides and a powerful brushless drive. It has an integrated control unit supporting the Interfaces: Ethernet TCP/IP, CAN-Bus (optional), PROFINET (optional) and Modbus/TCP (optional). Previous figure shows the components and connectors of the product. The configuration of the product is done via a Web-Interface supporting almost every common web browser. Furthermore, the product comes standard with a sensor port in the base jaws. Here gripper fingers can be connected with integrated sensors, which are evaluated directly from the gripper control. SCHUNK provides standardized finger as accessories, which work directly with the gripper control. For more information, please contact SCHUNK. 30 03.00 WSG 32 en

Assembly 5 5.1 Assembly Safety notes DANGER Risk of fatal injury due to electric current! Touching live parts poses an immediate risk of fatal injury by electrocution. Only allow a qualified electrician to perform work on electrical components. Prior to commencing work on electric components, restore to a de-energized state. In case of damage to the insulation, switch off the power supply immediately and arrange for a repair. Keep humidity away from live parts. WARNING Risk of injury due to unexpected movements! If the power supply is switched on or residual energy remains in the system, components can move unexpectedly and cause serious injuries. Before starting any work on the product: Switch off the power supply and secure against restarting. Ensure that no residual energy remains in the system. WARNING Risk of burns through contact with hot surfaces! Surfaces of components can heat up severely during operation. Skin contact with hot surfaces causes severe burns to the skin. For all work in the vicinity of hot surfaces, wear safety gloves. Before carrying out any work, make sure that all surfaces have cooled down to the ambient temperature. 03.00 WSG 32 en 31

Assembly 5.2 Mechanical connection The threads and centering holes which can be used to mount the product are shown in the following figure. The product has M3 and M4 threads for fixing on the rear of housing, as well as Ø 6 mm centering holes. The M4 threads together with the centering holes form part of the 50 mm ISO standard flange for industrial robots. When in holding mode, the product constantly adjusts the gripping force, to ensure a constant gripping force. The surfaces which are screwed together must be capable of dissipating the resulting heat. NOTICE Risk of overheating! Please ensure that the thermal coupling is good, especially if the product is to apply high gripping forces over longer periods of time. Prevent exposure to external sources of heat, such as from your robot s pan-tilt unit, as this can reduce the product s performance. Poor dissipation of heat or exposure to additional heat will require the gripping force to be reduced. NOTE To ensure fault-free operation and to minimize the radiation of electromagnetic interference (EMC) the product s housing must be properly earthed. 32 03.00 WSG 32 en

Assembly NOTICE Material damage due to incorrect tightening torques! Observe the maximum tightening torque: Screw M3: 1.0 Nm Screw M4: 2.0 Nm 5.3 Electrical connection As supplied, the product is configured so that the M8 connector carries both the power as well as the logic parts for the integrated gripper control system. If your application requires the power and logic parts to be separated, for instance if you would like to use an external relay to ensure that the gripping force is safely switched off (cf. "safe torque off", STO), then the power and logic parts can be supplied separately (see Fig. "Equivalent circuit for the power supply"). The power and logic supply are not electrically isolated so they must use the same power supply unit (see Fig. "Connection type common supply to load and logic"). If the supply to the load is to be switchable in operation, then the connection can be arranged as shown in "Connection type supply to load separate from supply to logic". 03.00 WSG 32 en 33

Assembly Equivalent circuit for the power supply Connection type common supply to load and logic Connection type supply to load separate from supply to logic 34 03.00 WSG 32 en

Assembly NOTE If load and logic are operated separately, always use the same power supply! 5.4 Installation of the fingers To install the standard fingers, please use the fixing material supplied with the fingers. The centering sleeves supplied with the fingers must be used during the installation. This is particularly necessary if the finger has an electrical interface to the sensor port as otherwise the sensor port's connector can be damaged. Installation of the fingers 1 Force measurement finger ABF WSG32/50-DV 3 Screw M4, ISO 4762 Tightening torque, max.: 2.5 Nm! 2 Base jaw 4 Centering sleeve 03.00 WSG 32 en 35

Start-up 6 6.1 Start-up Initial commissioning NOTE To ensure fault-free operation and to minimize the radiation of electromagnetic interference (EMC) the product s housing must be properly earthed. When starting up the product for the first time, please follow the steps below: 1 Using the Ethernet/Power cable, connect the product to the existing Ethernet network of alternatively to the network card in your PC or laptop. NOTE The product s IP address is factory-set to a static value of 192.168.1.20. Should you wish to operate several products in the same network and/or if this address is already in use, then you will have to change the product s IP address accordingly (e.g. set the 2nd product s IP address to 192.168.1.21). To do that, first connect the product directly to computer s network connection, to avoid address conflicts in the network. For more information about changing the IP address: ( 6.2, Page 39) To directly operate the product on your computer s network connection, you may have to alter your computer s network configuration. If in doubt, contact your system administrator. 2 Connect your product with the power supply (24 V, 3 A). The product will now start up. The indicator for the operating state will light up blue and after about 5 seconds it will start flashing quickly blue. This signals that the product is booting. After about 15 seconds the indicator will slowly flash white. The product is ready for use 3 On your computer, open the Internet browser and enter the address http://192.168.1.20. You will be presented with the product s configuration interface 36 03.00 WSG 32 en

Start-up The starting page of the web-based interface 4 From the menu, select the Motion -> Manual Control option and click on the Home button The product will now zero itself. 03.00 WSG 32 en 37

Start-up Manual Control configuration page 5 Once the homing sequence has been finished, for test purposes, you can move the product via the web interface. For this, select the movement parameters about the adjuster and then click on the Move button. Important: The product must have been zeroed to be able to execute movement commands. Other steps which you should take during the commissioning: 1 Call up the Diagnostics -> System State page, to check the product s supply voltage. 2 On the Settings -> Command Interface page, select the protocol on which your product is to be operated. 3 If necessary, on the Settings -> Motion Configuration page enable automatic homing during startup ( Homing on Startup ) 4 On the Settings -> System page, create a user with corresponding rights and activate the web interface s security function, to prevent changes to your setting by unauthorized persons. 38 03.00 WSG 32 en

Start-up 6.2 Changing the IP address and using DHCP To change the product s IP address, in the web interface, select the Settings -> Network option menu. Adjust the IP address, subnet masks and any gateway or DNS server addresses for your local network and confirm the changes by clicking on the Apply button. NOTE After changing the network configuration you will have to restart the product. To use addresses dynamically assigned via DHCP, check the corresponding box. In this case the product will automatically take its network configuration from a DHCP server. NOTE Please note that if you use DHCP to dynamically allocate IP addresses, there is no integrated way of finding out what IP address has been allocated. This is why the DHCP server should be config-ured so that the product is issued with an IP address which is known in advance For further information, please contact your network administrator. 03.00 WSG 32 en 39

Operation 7 Operation The product disposes a powerful integrated control unit. The control unit is accessible by removing the cover plate with the Schunk-Logo. Access shaft to the control unit 1 Button: configuration-reset 2 Memory card 3 LED: Access memory card 4 LED: networkactivity Via this tray, additional control LEDs and the memory card can be accessed. NOTICE Material damage due to improper fastening! The control unit can be damaged if using the wrong screws. Only use the supplied screws to mount the plate. 40 03.00 WSG 32 en

Operation 7.1 Operating software The software needed to operate the product is already installed in the unit. NOTE To guarantee proper operation, the latest version of firmware should always be installed in the product. The latest firmware can be obtained from the SCHUNK. 7.2 Memory card The gripper control unit has a slot to insert a MicroSD memory card. Although all common variants are supported (SD and SDHC), we recommend the use of the following memory cards: MicroSD card: Made by: SANDISK, type: SDSDQM-002G-B35, capacity: 2 GB The memory cards hold the following data: Software needed to operate the product Configuration data Documentation and software tools (can be called up via the web interface) Scripts and other user.specific data in the /user directory The card installed by the manufacturer has a capacity of 2 GB. The required operating software is already installed on the card. Userspecific data and scripts can be saved in the "user" subdirectory. Please do not change or delete any files outside of this directory as, otherwise, fault-free operation of the product can no longer be guaranteed. NOTE The memory card and the software which it contains are needed to operate the product. Should you wish to replace the memory card, please copy the contents of the original card onto the new one using a suitable card reader. 03.00 WSG 32 en 41

Operation 7.3 The boot process The product has a boot loader, which loads and runs the unit s software from the memory card when the unit is powered up. The indicator for the operating state will light up blue during this. If there is an error, the indicator will light up red for 5 seconds. After this the boot loader will automatically be restarted. This will continue until the firmware can be loaded correctly. 7.4 Display of operating state The product has a multi-colored indicator for the operating state. The current operating state is shown by both the color of the indicator as well as by the flash rate. Display of operating state The following operating states are indicated: State Loading the operating software The product loads the firmware and gets ready to start. Bootloader, interactive mode The bootloader has detected a connected VT100 terminal and is operated by it (in normal operation this state does not occur). There was an error loading the operating software After this the boot loader will automatically be restarted. Display Blue, constantly on Violet, continuously Red for about 5 seconds, then blue again 42 03.00 WSG 32 en

Operation State The boot process for the operating software. The operating software will be started and the control system will be configured. Wait state The product is ready for operation and is waiting for a command. Busy The product is in the initialization phase or is currently executing a command. Executing a script A script is being executed by the control system. Warning One or more parameters have reached warning limits. Please check the system s status via its web interface. Command received with no errors The product has received an error-free command. Error carrying out a command An error has occurred while receiving or executing a command. Critical fault An error has occurred (e.g. excess temperature, loss of communications, etc.). This error must be acknowledged before the product can process new commands to move. Critical software fault A serious error has occurred and the execution of the software in the unit has been stopped. The product will restart after a short time. Display Blue, flashing White, slowly pulsating White, quickly pulsating Green, quickly pulsating Yellow, quickly pulsating Green, pulses once Red, pulses once Red, pulses quickly Red, flash code 2x short, long pause More LEDs indicating SD card and communication activity can be found next to the SD card slot under the cover plate with the SCHUNK logo. A constant lightning of the respective LED indicates that the interface is active. The LEDs flash in the rhythm of the interface activity or data traffic. 03.00 WSG 32 en 43

Operation 7.5 Status word and gripper state The product's current state can be called up at any time via the status word and the gripper state. 7.5.1 Status word The current state of the product is summarized in the so-called status word. This can be read out via the command interface (using the command: Get System State, 40h), via the web interface or via a script (using the command: Read System State flags, gripper.state()). Following figure shows the display of the status word via the side bar in the web interface. The status word includes both pure status messages (e.g. zeroed, execution of script, etc.) as well as warnings and errors (e.g. temperature warning, power failure, etc.). NOTE You will find the documentation for the status word in the manual WSG Command Set Reference Web Interface side bar with system state 44 03.00 WSG 32 en

Operation 7.5.2 Gripper state The gripper state reflects the current state of the gripper and is used to control the process of gripping. It can take the following states: State IDLE GRIPPING HOLDING PART LOST NO PART FOUND RELEASING POSITIONING ERROR Description The gripper is in its idle state No gripping process is currently in progress The gripper is closing A part is being gripped, the fingers are moving towards the part. The detection of gripped items is active. A part is being held A part is being held with the configured force. The monitoring of the gripped part has been activated. A part has been lost The pre-configured gripping force can no longer be applied, presumably because the part to be gripped has been lost. No part has been found When closing the gripper at the configured position, no part was found to be gripped. The gripper is opening The gripped part is being released, the fingers are moving. Pre-positioning The gripper is being pre-positioned and the fingers are moving. Error An error occurred carrying out the last command. For errors which require acknowledgment, the SF_FAST_STOP flag is also set in the system status word. After any acknowledgment required, the movement can be restarted. The gripper's state is shown like the status word in the side bar of the web interface. The following diagram shows the possible transitions between the gripper s states. 03.00 WSG 32 en 45

Operation Transitions between the gripping states Stop command: Issuing a Stop command in any state (except ERROR) will abort the current action and immediately return to IDLE state. 46 03.00 WSG 32 en

Operation 7.6 Homing the product To detect the products's position, it is equipped with a measuring system which can detect the finger's spatial location at a high resolution. Due to the incremental method of position detection, the product has to be homed before motion commands can be executed. The product has a special command for homing which can be issued via the command interface, by a script or via the web interface. It then moves its fingers to the inner or outer physical limit and saves the measured position as a reference value. To offer maximum flexibility, the product can be referenced to the inner as well as to the outer limit. For outer homing, a factory-calibrated value is used to shift the reference position, so that both variants end up with the same direction and the same origin for the axis coordinates. NOTE Make sure that the fingers can actually move freely in the reference drive direction up to the product s mechanical limit. Due to the integrated damping elements at the outer limit, the grippers s position accuracy is better when homing to the inside. To automatically execute a homing sequence on start up, activate the Homing on Start up option via the web interface Settings - >Motion Configuration 03.00 WSG 32 en 47

Operation 7.7 Gripping, detecting parts to be gripped and monitoring the gripping The product is equipped with an integrated detector for parts to be gripped and a grip monitor, which allows reliable handling even for difficult parts without the use of external sensors. To configure these functions, the following parameters are available on the web interface Settings -> Motion Configuration: Parameter Part Width Tolerance ("Part Width Tolerance") Clamping travel ("Clamping Travel") Description The tolerance of the specified nominal gripper width which is sent to the product with the grasp command. This is measured as the relative gap between two fingers moving towards one another. If a part to be gripped has been detected, the product will attempt to apply the required gripping force by moving the fingers within this range. This is measured as the relative gap between two fingers moving towards one another. Parameters defining a grip The figure clarifies the function of these two parameters. A grip is only valid (which means it doesn't create an error) if the detected width of the part lies within the hatched area consisting of the part width tolerance and the clamping travel. If no part is detected, then the 48 03.00 WSG 32 en

Operation gripper state will change to "NO PART FOUND". If a contact is detected outside of the defined range, this will be detected as an axis block and the gripper's state will change to "ERROR". NOTE The detector of parts to be gripped and the grip monitoring are not running in pre-position mode ("Pre-position" command). NOTICE Material damage due to insufficient lubrication! In the case of long-term short travel, it is possible to dry the product. Every 1000 movements or at least once per day the gripper should be moved through its full range of travel. NOTE For soft parts to be gripped, it may be necessary to increase the clamping travel. Setting the part width tolerance to the full range of movement of the product (maximum settings) will deactivate the detection of axis blocking when gripping. 03.00 WSG 32 en 49

Operation 7.8 Software limit switch Software limit switch The product s travel can be limited via the software limit switch. There is one limit switch for an inner range ("MINUS") and one for an outer range ("PLUS"). If the software limit switches have been activated, then positioning commands to move fingers into this range will get a range error response and the command will not be executed. There is also protection from crossing the edges of these ranges. The monitoring will trigger a fast stop which requires acknowledgment if the fingers should be moved into these areas. The software limits can be set via the command interface, a script or the web interface (Settings -> Motion Configuration). WARNING These software limits do not represent a safety function as understood by the machine directive! NOTICE The software limit switches are always related to the reference position of the base jaws. Bodies on the base jaws or on the gripper jaws are not included! 50 03.00 WSG 32 en

Operation NOTE If the fingers are within the forbidden area when the software limit switches are activated, then only movements to leave this area will be possible. More information on this subject are in the manuals "WSG Command Set Reference Manual" and "WSG Scripting Reference Manual". 7.9 Fast stops requiring acknowledgment The product offers a so-called Fast Stop to put the product into a defined state in case of an error or malfunction. Fast Stops are displayed by setting the SF_FAST_STOP flag in the status word. If a fast stop is triggered, for example due to an insufficient voltage error, then all movement commands will be rejected until the error is acknowledged and any fault condition has been cleared, with corresponding error codes being returned (access denied). If the product is in Fast Stop state, power will be removed from the drives but the position reference will be retained. The error can be acknowledged both via the command interface (the command is: Acknowledging a Fast Stop or fault Condition, 24h) as well as manually by clicking on the "Ack" button in the side bar of the web interface ( 7.5.1, Page 44). Fast stops are recorded in the product's event log ( 7.10, Page 52). WARNING Loss of gripping power on fast stop! Workpieces can fall down and cause serious injury. The fast stop does not represent a safety function as understood by the machine directive. NOTE A fast stop can also be triggered via the command interface, by a script or manually via the web interface. NOTE More information on this subject are in the manuals "WSG Command Set Reference Manual" and "WSG Scripting Reference Manual". 03.00 WSG 32 en 51

Operation 7.10 Log memory The product has a non-volatile log memory in which important events can be recorded. The events can be saved with a timestamp and they are sorted in chronological order. If no time of day is available via the network, then the time in milliseconds since the system was started will be used. When the memory is full, the oldest events will be overwritten. The log memory can be read out via the web interface (Diagnostics ->System State). For diagnostic purposes, it can also be copied to the internal SD card and can be downloaded via the file manager integrated in the web interface: 1 Open the web interface. 2 Go to Diagnostics -> System Information. 3 Click on the "Dump" button underneath the log. A file "logfile.txt" will be created in the user directory on the SD card. 4 Download the file using the file manager. To do that, select "File Manager" in the in the menu "Scripting". Click on the file and start the download via the button. 7.11 Thermal monitoring To protect the product from overheating, its housing is constantly monitored during operation. The current housing temperature can be checked both via the web interface as well as the command interface. If the temperature measured exceeds the limit of 65 C, then a temperature warning will be issued. From a housing temperature of 70 C the product will change into temperature error mode and will switch the power output stage off via a fast stop. This temperature error must be acknowledged via the "Fast Stop Acknowledge" command. Temperature warnings and errors are recorded in the product's event log memory ( 7.10, Page 52). WARNING Loss of gripping force on temperature error! Workpieces can fall down and cause serious injury. 52 03.00 WSG 32 en

Operation NOTE This error can only be acknowledged if there is no longer a temperature error. The command to read out the current housing temperature and the command to acknowledge the Fast Stop via the command interface are documented in the "WSG Command Set Reference Manual". 7.12 Monitoring the motor current The drive current is continuously measured and monitored during operation. An integrated motor model is used to check whether the drive is being overloaded or not. In this case, the power output stage will be switched off via a fast stop and a "current fault" will be displayed. The current error must be acknowledged. This can either be done via the web interface or via the command interface using the "Fast Stop Acknowledge command. Current errors are recorded in the product's event log ( 7.10, Page 52). WARNING Loss of gripping force when there is a current error! Workpieces can fall down and cause serious injury. NOTE This error can only be acknowledged if there is no longer a current error. For the documentation of the command to acknowledge the "Fast Stop" via the command inter-face, see the "WSG Command Set Reference Manual". 03.00 WSG 32 en 53

Operation 7.13 Monitoring the supply voltage To ensure the correct functioning of the product, the supply voltage to its power section is continuously monitored. If this is outside a defined range, a warning or an error will be issued. The following limits apply: Threshold VDRIVE <= 20 V VDRIVE <= 22 V VDRIVE >= 26 V VDRIVE >= 28 V Consequence Low voltage fault SF_POWER_FAULT will be set in the system's status word and the status indicator will show the error state. Low voltage warning SF_POWER_WARNING will be set in the system's status word and the status indicator will show the warning state. Excess voltage warning SF_POWER_WARNING will be set in the system's status word and the status indicator will show the warning state. Excess voltage error SF_POWER_FAULT will be set in the system's status word and the status indicator will show the error state. Hysteresis is used to prevent the states chattering to and fro. If there is a voltage error, the power output stage will be switched off using a fast stop and a voltage error will be indicated. This must be acknowledged, but will only be possible when the operating voltage is back in its permissible range. You can do this either via the web interface or via the command interface via the "Fast Stop Acknowledge" command. WARNING Loss of gripper power following an error due to the voltage being too high or too low! Workpieces can fall down and cause serious injury. 54 03.00 WSG 32 en

Operation NOTE The low voltage fault will also be triggered if the power supply is interrupted when switching the force off, e.g. via an emergency stop relay. This error can only be acknowledged when there is no longer a high/low voltage error. Futher information of the system status word and of the command to acknowledge the "Fast Stop" via the command interface, see the "WSG Command Set Reference Manual". 7.14 Configuration and diagnosis via the web interface The product has an integrated web server, with an user interface for configuration and diagnosis. To use this, the product must be connected via Ethernet. To get to the configuration user interface, open a browser and enter the product's IP address (on delivery this is 192.168.1.20) into the browser's address line: Entering the IP address to start web-based configuration The following browsers have been tested and support the product s web interface: Mozilla Firefox 16 and above Google Chrome 23 and above Apple Safari 5 and above Mobile Safari (ios 4.3 and above) Internet Explorer 8 and above NOTE To display the web user interface, JavaScript must be enabled in your browser. 03.00 WSG 32 en 55

Operation Web interface for configuration and diagnosis Via integrated help texts, the product s web interface is intuitive to use. In the upper area you will find a menu bar via which the individual pages can be called up. 56 03.00 WSG 32 en

Operation 7.14.1 Access restrictions for the web user interface Depending on the network configuration, the product will be visible to everyone in the entire network and the configuration can thus be altered unchecked. To restrict access to the product's web interface, under Settings -> System Configuration you can activate access restrictions for the interface and create users with differing access rights. Login screen If this is activated, each user must be identified with a login name and personal password. Every user is assigned to one of the following user groups: User Standard user: Cannot adjust settings, but can only access the pages under the menu options Diagnostics and Help. Administrator Administrator: Can adjust all of the product s settings without restriction. 03.00 WSG 32 en 57