C1 Preliminary Product Specification IEEE 802.11 b/g/n Wireless CPE Model Name: ZN72002EIO HW: 0.1
1 Revision History Date Version Author Description 2013/10/14 V0.1 Nancy 1 st draft version
2 Specification 2.1 Hardware Specification The Hardware specifications of the product are as below: Table 21 Hardware Specification Features Additional Information Chipset Solution CPU: AR9342 RF: AR9342 Standard Compliance IEEE802.3u MDI / MDIX 10/100 Fast Ethernet IEEE802.11b/g/n wireless LAN interface IEEE 802.11n wireless LAN standard DDRII 64Mbyte Flash 16Mbyte Power input requirement Passive PoE 15V Pin 4,5 VDC+ Pin 7,8 VDC CPU Rate 400MHz Ethernet PHY 10/100 Mbps Antenna Antenna Frequency band Return loss Isolation Vertical Port HPBW Antenna Connector LAN port Reset Button Default external 5 dbi Omni antenna 2.4~2.5GHz TBD TBD TBD SMA x2 1port Reset to factory default Ground Ground terminal x1 System Update Capability Support WebUI upgrade via Ethernet port or wireless network Support TFTP upgrade via Ethernet port LED Definition Power (Singlecolor LED x1) Green On: Power / system on Green Off: power / system off LAN (Singlecolor LED x1) Off: No Ethernet connection detected Green On: Ethernet connection detected Green Blinking: Sending / receiving data WLAN (Singlecolor LED x1) Green Off: WLAN disabled Green On: WLAN enable Green Blinking: WLAN data transmit Signal *3 (Singlecolor LED x3) Excellent: 3 LED Green ON Good: 2 LED Green ON Weak: 1 LED Green ON Data Rate 11b: 11M, 5.5M, 2M, 1Mbps
11g: 54M, 48M, 36M, 24M, 18M, 12M, 9M, 6Mbps 11n: HT20 MCS0~15 HT40 MCS0~15 Data modulation type DSSS/BPSK/QPSK/CCK/DQPSK/DBPSK 802.11b/g/n: OFDM 802.11n: OFDM RF frequency range FCC: 2.412 GHz ~ 2.462 GHz CE: 2.412 GHz ~ 2.472 GHz Power Consumption (W) <12W Average Output Power @ 25 11b 1,5,11Mbps 27dB 24Mbps (Single Chain) (± 2dBm) 1 11g 6, 9, 12, 18, 25dB 36Mbps 24dB 48, 54Mbps 23dB 11gn(HT20) MCS0, MCS8 27dB MCS1,MCS2,MCS3, 26dB MCS9,MCS10, MCS11 MCS4, MCS12 25dB MCS5, MCS13 24dB MCS6, MCS7, MCS14, 23dB MCS15 11gn(HT40) MCS0, MCS8 26dB MCS1,MCS2,MCS3, 25dB MCS9,MCS10, MCS11 MCS4, MCS12 24dB MCS5, MCS13 23dB MCS6, MCS7, MCS14, MCS15 22dB Sensitivity (at single chain) Mode 11b 11g 11n HT20 11n HT40 FER<8% FER<10% FER<10% FER<10% 11 85 5.5 88 2 89 1 91 6 89 9 88 12 85 18 83 24 80 36 76 48 71 54 70 0/8 83 1/9 80 The listed value is the target power calibrated in the card. The actual power will vary depending on each country s regulation. For detailed CTL table settings please contact our sales representative.
2/10 78 3/11 75 4/12 71 5/13 67 6/14 66 7/15 65 0/8 80 1/9 77 2/10 75 3/11 72 4/12 68 5/13 64 6/14 63 7/15 62
2.2 Firmware Specification The Firmware Specifications of ZN72002EIO as below: Function Catalog Detail Function Default settings Web Language English English Status Information Connections Statistics ARP Table Bridge Table DHCP Client List Network Activity System Basic Settings: 1. Device Mode 2. Device Name 3. Ethernet DateRate 4. Network Modes 5. Country/Region 6. Spanning Tree (STP) 7. STP Forward Delay 8. GPS Coordinate Wireless TCP/IP Settings (Bridge Mode): TCP/IP Settings (Router Mode): Time Setting RADIUS Settings Firewall Setting (Router Mode Only) Basic Wireless Settings Table 21 Firmware Specification (Fat AP Mode) IP Address (Manual or DHCP, In DHCP mode, if DHCP server is not available, then use manually set IP address) 1. WAN Settings 1. Static IP 2. DHCP Client 3. PPPoE 2. LAN Settings 1. DHCP Server 1. Current Time 2. Time Zone Select 3. Enable NTP client update IP Address of Authentication RADIUS Server 1. Src IP Filtering 2. Dest IP Filtering 3. Src Port Filtering 4. Dest Port Filtering 5. Port Forwarding 6. UDP Passthrough 7. DMZ Disable Wireless LAN Interface Operation Mode AP Mode Function: 1. SSID 2. Broadcast SSID apxxxxxx Auto Bridge United States Enable 1 (second) Manual, 192.168.1.1 GMT 0.0.0.0 Unselected AP Wireless
3. 802.11 Mode 4. HT Protect 5. Frequency/Channel 6. Extension Channe 7. Channel Model 1. 5MHz 2. 10MHz 3. 20MHz 4. 40MHz 8. Antenna 9. Maximum Output Power (per chain) 10. Date Rate 11. Extension channel protect mode CTS to self 1. RTSCTS Wireless Client Mode Function: 1. SSID 2. Lock AP MAC 3. 802.11 Mode 4. Channel Model 1. 5MHz 2. 10MHz 3. 20MHz 4. 40MHz 5. Antenna 6. Maximum Output Power (per chain) 7. Extension channel protect mode 1. 2. CTS to self 3. RTSCTS 8. Enable MAC Clone Bridge Mode Function: 1. 802.11 Mode 2. Frequency/Channel 3. Extension Channe 4. Channel Model 1. 5MHz 2. 10MHz 3. 20MHz 4. 40MHz 5. Antenna 6. Maximum Output Power (per chain) 7. Data Rate 8. Extension channel protect mode 1. 2. CTS to self 3. RTSCTS 802.11b/g/n 2437MHz (6) 20MHz Internal (8dBi) Full (26dBm) Auto Wireless 802.11b/g/n 20MHz Internal (8dBi) Full (26dBm) 802.11b/g/n 2437MHz (6) 20MHz Internal (8dBi) Full (26dBm) Auto AP Repeater Mode Function: 1. SSID Wireless
2. Broadcast SSID 3. 802.11 Mode 4. HT Protect 5. Frequency/Channel 6. Extension Channe 7. Channel Model 1. 5MHz 2. 10MHz 3. 20MHz 4. 40MHz 8. Antenna 9. Maximum Output Power (per chain) 10. Date Rate 11. Extension channel protect mode 1. 2. CTS to self 3. RTSCTS Profile Settings 1. VAP Profile Settings (up to 16 profiles) 2. Enable 802.1Q VLAN 1. Management VLAN ID Enable 802.11b/g/n 2437MHz (6) 20MHz Internal (8dBi) Full (26dBm) Auto 0 In Each Profile: Basic Settings 1. Profile Name 2. SSID 3. Broadcast SSID 4. Wireless Separation 5. WMM 6. Station Number Limitation 7. Max. Station Num Profile1~16 Wireless 32 Security Settings Open System 1. Open System 2. Shared Key(64/128/152bits WEP) 3. Lagacy 802.1X 4. WPA 5. WPA2 6. WPA + WPA2 7. WPAPSK(TKIP) 8. WPA2PSK(AES) 9. WPAPSK + WPA2PSK Advanced settings AMPDU Aggregation AMSDU Aggregation Short GI RTS Threshold(0~2347) 2347 Fragmentation Length(256~2346) 2346 Beacon Interval(20~10000ms) 100 DTIM Interval (1255) 1 Preamble Type Auto
Manageme nt IGMP Snooping RIFS Link Integration TDM Coordination Spaceinmeter 1000 (m) Access Control Support up to 32 MAC addresses for each profile with modes below: 1. Disable 2. Allow Listed 3. Deny Listed Traffic Shaping 1. Overall Traffic Shaping 1. Incoming Traffic Limit 2. Incoming Traffic Burst 3. Outgoing Traffic Limit 4. Outgoing Traffic Burst 2. VAP Traffic Shaping (per VAP profile) 1. Outgoing Traffic Limit 2. Outgoing Traffic Burst Captive Portal Support CoovaChilli Access Controller (enable/disable per VAP profile) 1. RADIUS Settings 1. Primary RADIUS Server 2. Secondary RADIUS Server 3. RADIUS Auth Port 4. RADIUS Acct Port 5. RADIUS Shared Secret 6. RADIUS NASID 2. Captive Portal Settings 1. UAM Portal URL 2. UAM Secret WDS Setting WDS Separation Remote AP Address1~4 Remote Embedded Web Configuration Interface HTTP 1. HTTP Management 2. HTTPS Remote Console Telnet Telnet 1. SSH SNMP Management V2 V2 1. V3 FTP WISE (Windowsbased Utility Software) Firmware Upload Upgrade Device s Firmware Configuration File 1. Backup and Restore Configuration 2. Reset Settings to Factory Default 3. Reboot Device Password Settings Change Password password Certificate Settings Import / Delete User s Certificate Files for Wireless Client Mode s User Authentication
(802.1X, WPA, or WPA2) Tools System Logs Syslog (RFC 3164) Support Site Survey Wireless Network (AP) Scan Tool Ping Watchdog Enable Ping Watchdog IP Address to Ping Ping Interval Startup Delay Failure Count To Reboot Data Rate Test Antenna Alignment Speed Test Perform PerDatarate Transmission Test and Display Throughput Statistics (WDS Mode Only) Perform Continuous Throughput Statistics for Antenna Alignment (WDS Mode Only) Perform TCP/IP Data Throughput Test (All Mode) 0.0.0.0 300 Seconds 100 Seconds 300 Table 22 Firmware Specification (AC & Thin AP Mode) Function Catalog Detail Function Default settings Web Language English English Status Information Managed APs Wireless Settings Wireless Networks Wireless Users Wireless Network Name (SSID) Settings, up to 16 SSID profiles can be activated. In Each Profile: Basic Settings 1. SSID 2. Description 3. Broadcast SSID 4. Wireless Separation 5. WMM 6. Station Number Limitation 7. Max. Station Num Security Settings 1. Open System 2. Shared Key(64/128/152bits WEP) 3. Lagacy 802.1X 4. WPA 5. WPA2 6. WPA + WPA2 7. WPAPSK(TKIP) 8. WPA2PSK(AES) 9. WPAPSK + WPA2PSK Wireless Profile1 ~ 16 32 Open System
Wireless Protocol Basic Settings 1. Country Region 2. 802.11 Mode 3. Data Rate Advanced Settings 1. AMPDU Aggregation 2. AMSDU Aggregation 3. Short GI 4. IGMP Snooping 5. RIFS 6. HTProtect 7. Preamble Type 8. RTS Threshold(0~2347) 9. Fragmentation Length(256~2346) 10. Beacon Interval(20~10000ms) 11. DTIM Interval (1255) 12. Extension Channel Protection 13. Space In Meter 14. Link Integration 15. TDM Coordination Access Control Support up to 32 MAC addresses for each profile with modes below: 1. Disable 2. Allow Listed 3. Deny Listed Traffic Shaping 1. Overall Traffic Shaping 1. Incoming Traffic Limit 2. Incoming Traffic Burst 3. Outgoing Traffic Limit 4. Outgoing Traffic Burst 2. VAP Traffic Shaping (per VAP profile) 1. Outgoing Traffic Limit 2. Outgoing Traffic Burst Captive Portal Support CoovaChilli Access Controller (enable/disable per VAP profile) 1. RADIUS Settings 1. Primary RADIUS Server 2. Secondary RADIUS Server 3. RADIUS Auth Port 4. RADIUS Acct Port 5. RADIUS Shared Secret 6. RADIUS NASID 2. Captive Portal Settings 1. UAM Portal URL 2. UAM Secret RADIUS Settings IP Address of Authentication RADIUS Firewall Setting (Router Mode Only) Server 1. Src IP Filtering 2. Dest IP Filtering 3. Src Port Filtering 4. Dest Port Filtering United States 802.11a/b/g/n Auto Auto 2347 2346 100 1 1000 (m) 0.0.0.0
5. Port Forwarding 6. UDP Passthrough 7. DMZ Management AP Management Management of Individual Thin APs 1 Restart 2 Rename 3 Set IP 4 Radio 4.1 Channel Mode 4.2 Channel 4.3 Extension Channel 4.4 Antenna 4.5 Output Power 5 Upgrade Selected 6 Upgrade All System Settings: 1. Device Settings 1. Device Mode 2. Device Name 3. Ethernet DateRate 4. Spanning Tree (STP) 5. STP Forward Delay 2. IP Address Settings 1. (AC) Device s IP Address (Manual or DHCP, In DHCP mode, if DHCP server is not available, then use manually set IP address) 2. DHCP Server for configuring IP Time Settings Firmware Upload Addresses of Thin APs 1. Current Time 2. Time Zone Select 3. Enable NTP client update Upgrade Device s Firmware 1. AC Firmware 2. TAP Firmware 20MHz 2437MHz (6) Internal (8dBi) Full (26dBm) apxxxxxx Auto Enable 1 (second) Manual, 192.168.1.1 GMT Configuration File 1. Backup and Restore Configuration 2. Reset Settings to Factory Default 3. Reboot Device Password Settings Change Password password Syslog Settings 1. Syslog (RFC 3164) Support 2. EMail (SMTP) Support System Log Display System Log System Alert Display System Alert Tools Ping Perform ICMP ping Test Trace Route Perform traceroute Test
2.3 Power Adapter Specification Output: 15V @ 0.8A (switching) 2.4 Physical specification The Physical specifications of the product are as below: Table 24 Physical Specification Items Description Dimension 205mm(L) 64mm(W) 61mm(H) Weight 500g Enclosure IP55 2.5 Environment specification The Environment specifications of the product are as below: Table 25 Environment Specification Items Device Description Power Adapter Spec Operating Temperature(Max) 20 ~ +70 C 0 ~ +40 C Operating Humidity (noncondensing) 10 to 95% RH 20 to 85% RH Storage Temperature 40 ~ +70 C 20 ~ +60 C Storage Humidity (noncondensing) 10 to 95% RH 5 to 95% RH Warranty Green 12 Months RoHs/REACH Compliant
2.6 Safety/Country Approval We will do EMI/EMC pretest according to the following items: FCC Table 26 Safety/Country Approval Items Description ID number Part15 sub B Part15 sub C CE EN300 328 CCC EN301 4891/17 EN60950 For China 2.7 Packaging Specification The following items will be required for the complete packaging of the ZN72002EIO: Table 27 Package Item Comments Carton Gift Box / Cushion ZN72002EIO Power Supply PoE injector Steel Cable Tie Suitable size to fit in Suitable size to fit in Whole product should be in a protective bag Appropriate adapter based on the region Suitable size to fit in Suitable size to fit in
3 Pin Assignment And Dimension of DiP Connector Item Description & Pin Assignment RJ45 PCB Jack 1Port Pin NO. Signal Name Pin Definition (ETH) 1 RX+ Receive (+) 2 RX Receive () 3 TX+ Transmit (+) 4 15V + Power Supply 5 15V + Power Supply 6 TX Transmit () 7 GND GND 8 GND GND RS232 1PORT4Pin (RS232) Pin NO. Signal Name Pin Definition 1 VCC 3.3V 2 GND GND 3 UART_SOUT UART_TX 4 UART_SIN UART_RX
(Reset) Pin NO. Signal Name Pin Definition 1 AR9342_RES AR9342_RES 2 GND GND 3 FGND FGND 4 FGND FGND