System connector ultra low profile 18, 22 and 24 contacts I/O connectors for portable equipment 18, 22, 24 and 26 contacts 50 contacts FOR CELLULR PHONE; ULTR LOW PROFILE TYPE FOR PORTBLE EQUIPMENT (0.5mm PITCH) FETURES 1. Compact receptacle helps to design lighter, slimmer, smaller devices. 1) Super low-profile system connector. Board cutting Cutting PC board On board mounting Ultra low-profile 3mm Ultra low-profile 3mm XR(3/5) SYSTEM CONNECTORS ULTR-LOW PROFILE TYPE (XR3) I/O CONNECTORS FOR PORTBLE EQUIPMENT (XR5) 3. Coaxial portion with switching function (1 Form B configuration) can be applied up to 2GHz. 4. Connection of incorrect pairs is prevented by cross-manufacturer mating error prevention key. By changing the location of the mating error prevention key, erroneous insertion of a different connector is prevented. This eliminates the chance of any problems that may be caused by mistaken connections. Please consult us for more information. Error prevention key System connector ultra low profile Plug (cable connection ) 18, 22, 24 and 26 contacts 2) I/O connector for portable equipment 18, 22, 24 and 26 contacts Ultra low-profile mm PC board 0.5mm pitch 7.2mm The key groove is different for every customer. 5. Plugs with 22, 26 and 50 contacts are also available in board mounting s. These are ideal for such applications as the connection between PDs and datacommunication cradles. 50 contacts I/O connectors for portable equipment Plug (cable connection ) 50 contacts Ultra low-profile 3.5mm 0.5mm pitch 8.0mm PC board PC board Plug (Board mounting ) System connector ultra low profile Plug (Board mounting ) 22, 26 and 50 contacts 2. Bellows- contacts Our bellows- contacts resist mating stress and offer high contact reliability. Contact Plug side The bellows contacts are fabricated by bending thin sheet metal. They offer reliable contact since a rounded corner, instead of a sharp edge, is used for tuning fork contact. side 6. Compliance with RoHS Directive Environmentally friendly, the connectors comply with Europe s RoHS Directive. Cadmium, lead, mercury, hexavalent, chromium, PBB and PBDE are not used. Customizable for several contacts. sk about details. ll Rights Reserved COPYRIGHT Matsushita Electric Works, Ltd.
XR(3/5) ORDERING INFORMTION 1. System connectors ultra-low profile receptacle 2. I/O connectors for portable equipment receptacle 3: System connectors ultra-low profile <Composite function> 2: Coaxial, with battery terminal 5: With battery terminal <No. of signal wire> 2: SIL 18 contacts 3: SIL 4: SIL 24 contacts XR <No. of coaxial pole> 7: Without coaxial 8: 1 pin <On board/board cutting> 1: On board 4: Board cutting <Packing> P: Embossed tape and paper reel 2 V: Embossed tape and paper reel 5 5: I/O connectors for portable equipment <> 1: <No. of signal wire> 18: SIL 18 contacts 22: SIL 24: SIL 24 contacts 26: SIL 26 contacts 50: SIL 50 contacts <Function> / 4 8 XR On board/ board cutting/ board mounting On board <Packing> P: Embossed tape and paper reel 2 Positioning boss Not available 3. System connectors ultra-low profile plug 4. I/O connectors for portable equipment plug 3: System connectors ultra-low profile <Plug> 0: Plug <No. of signal wire> 2: SIL 18 contacts 3: SIL 4: SIL 24 contacts 5: SIL 26 contacts 6: SIL 50 contacts XR <On board/board cutting/no. of coaxial pin> On board/board cutting No. of coaxial pin 4 On board Without 7 1 pin Board cutting 9 Without <Function> Cable connection / Board mounting 0 1 Cable connection 3 4 5 Board mounting / <Packing> Nil: Embossed tape and paper reel 2 * Board mounting only. Shield vailable Not available vailable 5: I/O connectors for portable equipment <Plug, /> 2: Plug <No. of signal wire> 5: SIL 50 contacts XR <pplicable cable dia.> 6: 5.5mm dia. 7: 6.2mm dia. <Shield> S: With shield Note) pplicable for cable connection 50 contacts ll Rights Reserved COPYRIGHT Matsushita Electric Works, Ltd.
RECEPTCLE ND PLUG COMPTIBILITY TBLE 1. s 18 to 50 contacts 1) Plug (Cable connection ) Plug Combination table XR(3/5) Plug ( )- ( ) are mated No. of signal terminals On board/board cutting composite function Part No. (Plug) Part No. () 50 contacts On board mounting s only Plug ()- ( ) are mated XR5256S XR5257S XR51508P Design side Corresponds to on board mounting receptacle 50 contacts Design side Corresponds to board cutting receptacle 18 and Corresponds to on board mounting receptacle 18, 22, 24 and 26 contacts No. of signal terminals On board/board cutting composite function Part No. (Plug) Part No. () Coaxial 1 pin 18 contacts Board cutting XR30274 XR32284P Battery terminal 4 contacts Battery terminal 4 contacts XR30394 XR35374P 18 contacts s only XR30244 XR51188P 24 contacts 24 contacts 26 contacts On board mounting s only Battery terminal 3 contacts s only Battery terminal 3 contacts s only Plug ()- () are mated XR30341 XR30344 XR30341 XR30344 XR30444 XR30444 XR30541 XR51228P XR35371P XR51248P XR35471V XR51268P Board cutting 18 and On board mounting 18, 22, 24, 26 and 50 contacts On board mounting No. of signal terminals On board/board cutting composite function Part No. (Plug) Part No. () On board mounting s only XR30341 XR30344 XR51224P Plug (Board mounting ) Plug Combination table Plug ( )- ( ) are mated Corresponds to on board mounting receptacle Corresponds to on board mounting receptacle 22, 26 and 50 contacts No. of signal terminals On board/board cutting composite function Part No. (Plug) Part No. () On board mounting s only XR3034 XR51228P Battery terminal 3 contacts XR3034 XR35371P Plug ( )- () are mated No. of signal terminals On board/board cutting composite function Part No. (Plug) Part No. () On board mounting s only XR3034 XR51224P Plug ()- ( ) are mated No. of signal terminals On board/board cutting composite function Part No. (Plug) Part No. () 26 contacts On board mounting XR30545 XR51268P 50 contacts s only XR30645 XR51508P Plug ()- () are mated On board mounting 22, 26 and 50 contacts On board mounting No. of signal terminals On board/board cutting composite function Part No. (Plug) Part No. () On board mounting s only XR30345 XR51224P ll Rights Reserved COPYRIGHT Matsushita Electric Works, Ltd.
XR(3/5) 3. Information about and s Plug 1) Cable connection When the contact side and design side, face in the same direction it is Type face in opposite directions it is B Type Design side When the contact side and mounting side, face face in opposite directions it is Type face the in the same direction it is B Type Contact side Design side Contact side Contact side Mounting side 2) Board mounting When the contact side and mounting side, face in the same direction it is Type face in opposite directions it is B Type Mounting side Contact side Mounting side Mounting side Contact side Contact side PRODUCT TYPES 1. No. of signal terminals Type Note) For cellular phones and other applications where problems of insertion into the wrong device is possible, the location of the key will be changed for each order. n order number will be set for each separate order. 2. Plug (Cable connection ) No. of Type EMI immunity Part No. signal terminals Note) For cellular phones and other applications where problems of insertion into the wrong device is possible, the location of the key will be changed for each order. n order number will be set for each separate order. 2. Plug (PC board mounting ) No. of Type signal terminals No. of coaxial No. of battery terminal Part No. Packing quantity Inner carton (1 reel) Outer carton 18 contacts Board cutting ( ) 1 4 contacts XR32284P 700 pcs. 1,400 pcs. On board mounting ( ) None None XR51188P 1,000 pcs. 2,000 pcs. Board cutting ( ) None 4 contacts XR35374P 700 pcs. 1,400 pcs. On board mounting ( ) None None XR51228P 1,000 pcs. 2,000 pcs. On board mounting ( ) None 3 contacts XR35371P 700 pcs. 1,400 pcs. On board mounting () None None XR51224P 1,000 pcs. 2,000 pcs. 24 contacts On board mounting ( ) None None XR51248P 1,000 pcs. 2,000 pcs. On board mounting ( ) None 3 contacts XR35471V 700 pcs. 3,500 pcs. 26 contacts On board mounting ( ) None None XR51268P 1,000 pcs. 2,000 pcs. 50 contacts On board mounting ( ) None None XR51508P 750 pcs. 1,500 pcs. Packing quantity Inner carton Outer carton 18 contacts Board cutting () Not available XR30274 600 pcs. On board mounting () Not available XR30244 600 pcs. Board cutting () Not available XR30394 600 pcs. vailable XR30341 600 pcs. On board mounting () Not available XR30344 600 pcs. 24 contacts On board mounting () Not available XR30444 600 pcs. 26 contacts On board mounting () vailable XR30541 600 pcs. 50 contacts On board mounting ( ) vailable XR5256S (for 5.5 dia. cable) 200 pcs. On board mounting ( ) vailable XR5257S (for 6.2 dia. cable) 200 pcs. EMI countermeasure Part No. Packing quantity Inner carton Outer carton On board mounting ( ) vailable XR3034 500 pcs. 1,000 pcs. On board mounting () vailable XR30345 500 pcs. 1,000 pcs. 26 contacts On board mounting () vailable XR30545 500 pcs. 1,000 pcs. 50 contacts On board mounting () vailable XR30645 500 pcs. 1,000 pcs. ll Rights Reserved COPYRIGHT Matsushita Electric Works, Ltd.
SPECIFICTIONS 1. Characteristics 1) Plug (cable connection ) Electrical characteristics High frequency characteristics (Coaxial portion) Mechanical characteristics Lifetime characteristics Environmental characteristics Unit weight Item Rated Current Contact resistance Signal contact Battery contact Signal contact Battery contact Insulation resistance Breakdown voltage 18 contacts (with coaxial) Note) Refer to above table for the characterics of the receptacle. Specifications 18 (without coaxial) 26 contacts 50 contacts 22, 24 contacts 0.5 (1 can be passed through two terminals connected in series) (Total for all terminals is max. 10.) 2 Max. 110mΩ (Initial) Max. 50mΩ (Initial) Min. 1,000MΩ (Initial) 150V C for 1 min. XR(3/5) Condition Characteristic of receptacle alone. Measured based on the milliohmmeter measurement method of JIS C 5402, except for the resistance of the cord on the plug side. Measured based on the milliohmmeter measurement method of JIS C 5402, except for the resistance of the terminals on the battery side. Using 500V DC megger (applied for 1 min.) Rated voltage is applied for one minute and check for short circuit or damage with a detection current of 1 m. Nominal impedance 50Ω pplicable frequency DC to 2GHz Lever lock strength Insertion and removal life of plug and receptacle mbient temperature Storage temperature Resistance to soldering heat Mechanical life: 10,000 times Contact resistance after testing: Max. 110 mω High frequency characteristics of coaxial portion: Satisfies high frequency characteristics given above Min. 49N {5kgf} Mechanical life: 10,000 times Contact resistance after testing: Max. 110mΩ 35 C to +65 C 40 C to +70 C (The allowable storage temperature is 40 C to +50 C if unopened from original packaging) Reflow soldering: peak temperature 245 C or less Mechanical life: 5,000 times (mechanical insertion and removal) Contact resistance after testing: Max. 110mΩ The plug is pulled off with the connectors mated. The connectors are connected and disconnected at a rate of 200 times/hour or less. No freezing or condensation in low temperatures No freezing or condensation in low temperatures Surface temperature (shell) from infrared reflow soldering machine Plug Hand soldering: Soldering iron temperature 300 C, 5 sec. or less (XR32284P): 1 g Plug (XR30274): 6.46 g (XR35371P) : 0.86 g Plug (XR30341) : 6.18 g 2) Plug (Board mounting ) Item Specifications 22, 26, 50 contacts Rated Signal 0.5 (7 can be passed through all terminals connected) current contact (The total for 50 terminals is max. 10.) Electrical characteristics Lifetime characteristics Environmental characteristics Unit weight Contact resistance Signal contact ( ) Max. 110 mω (Initial) () Max. 140 mω (Initial) 26 contacts () Max. 110 mω (Initial) 50 contacts () Max. 110 mω (Initial) (XR51508P) 50 contacts: 1.42 g Plug (XR5256S) 50 contacts: 11.1 g Condition Measured based on the milliohmmeter measurement method of JIS C 5402 Insulation resistance Min. 1,000MΩ (Initial) Using 500V DC megger (applied for 1 min.) Breakdown voltage 150 V C for 1 min. Rated voltage is applied for one minute and check for short circuit or damage with a detection current of 1 m. Insertion and removal life of plug and receptacle Mechanical life: 5,000 times Contact resistance after testing: Max. 110 mω (Contact resistance after testing satisfies initial value.) The connectors are connected and disconnected at a rate of 200 times/hour or less. mbient temperature 35 C to +65 C No freezing or condensation in low temperatures Storage temperature 40 C to +70 C (The allowable storage temperature is 40 C to +50 C if unopened from original packaging) No freezing or condensation in low temperatures Resistance to soldering heat Plug Reflow soldering: peak temperature 245 C or less ( ): 1.43 g, (): 1.53 g, 26 contacts (): 1.48 g, 50 contacts (): 2.30 g ll Rights Reserved COPYRIGHT Matsushita Electric Works, Ltd. Surface temperature (shell) from infrared reflow soldering machine
XR(3/5) 2. Material and surface treatment Portion Material Surface Resin-molding portion Heat resistant resin (UL94V-0) Shell Stainless steel Cu plating base, Sn plating on surface Contact portion: Ni plating on base, u plating on surface Post/battery contact Copper alloy Terminal portion: Ni plating on base, u plating on surface (except for end of the terminal) Resin-molding portion Heat resistant resin (UL94V-0) Only bushing is polyurethane resin (UL94HB) Plug Shell Stainless steel (cable connection Contact portion: Ni plating on base, u plating on surface Contact Copper alloy ) Signal wire soldering portion: Ni plating on base, u plating on surface Tapping screw Carbon steel Rust proofed Insulation plate Phenolic resin or PBT Plug (Board mounting ) Resin-molding portion Heat resistant resin (UL94V-0) Shell Stainless steel Cu plating base, Sn plating on surface Contact Copper alloy Contact portion: Ni plating on base, u plating on surface Terminal portion: Ni plating on base, u plating on surface (except for end of the terminal) DIMENSIONS 1. s 18 contacts/board cutting (1 coaxial/battery terminal 4 contacts) ( ) XR32284P - cross section 7.0±0.2 1.5 1.4±0.2 0.8±0.1 0.3±0.05 B B 17.0±0.2 26.5 24.1 20.1 17.4 5.2 10.8±0.2 16.7±0.2 3.8 Note 1) Note 1) 1.5 7.2±0.2 8.2±0.2 10.0±0.2 (5.3) (6.3) 5.9 1.5±0.1 4.4±0.2 B-B cross section Coaxial terminal 1.5±0.2 R 0.5 1.1±0.1 Battery terminal 2.1±0.1 3.6±0.05 1.2±0.05 0.7±0.05 2.8±0.1 1.9±0.05 0.6±0.05 12.35±0.05 10.35±0.05 2.8±0.05 3.7±0.1 11.8±0.1 16.7±0.05 11.75±0.05 9.75±0.05 8.5±0.05 2.4±0.05 1.5±0.1 1.8±0.1 1.9 2.7 2.9±0.1 0.8±0.05 2.1±0.1 4.0±0.1 (1.5) Please make pattern both side of PC board Notes) 1. The position of the cross-manufacturer mating error 2. Since product bottom is a metal shell, do not make pattern circuits (to prevent shorting). ll Rights Reserved COPYRIGHT Matsushita Electric Works, Ltd.
Plug (cable connection ) () (assembled condition) XR30274 Note) 2.9 Note) 1.5 XR(3/5) 2.35 Note) The position of the cross-manufacturer mating error 23.7 20.5 16.3±0.2 7.8 48.4 34.2 7.6 8.9 5.5 19.0 21.7 11.7 Circuit diagram of coaxial portion No. of signal terminal ( ) (Coaxial portion when not mated) Coaxial ground Common NC Coaxial ground Terminal NO. 1 NC Battery contacts terminals Coaxial ground terminals Common terminals s Terminal NO. 18 Battery contacts (Coaxial portion when mated) Coaxial ground Common NC Coaxial ground Plug Ground Center conductor 2. s 18 contacts/on board mounting ( ) XR51188P 0.2±0.05 7.2±0.2 7.0±0.2 Note) 1.3 8.5± Note) 4.5 13.3 13.7 3.3 - cross section 1.9±0.05 4.4±0.1 8.5±0.05 5.0 0.6±0.05 1±0.05 1.7 1.5±0.1 1.8±0.1 2.7 1.9 Please make pattern both side of PC board 0.2 ±0.1 0.3±0.05 1±0.2 0.45 1.5±0.1 4.4±0.2 R 0.5 Notes) 1. The position of the cross-manufacturer mating error 2. Since product bottom is a metal shell, do not make pattern circuits (to prevent shorting). ll Rights Reserved COPYRIGHT Matsushita Electric Works, Ltd.
XR(3/5) Plug (cable connection ) () (assembled condition) XR30244 8.5± 2.35 Note) The position of the cross-manufacturer mating error 23.7 Note) 1.15 20.5 12.6 Note) 4.5 7.8 0.3 48.4 7.6 34.2 28.9 8.9 5.5 15.0 19.0 21.7 11.7 No. of signal terminal ( ) Terminal No.1 Terminal No.18 3. s /Board cutting (with battery terminal 4 contacts) ( ) XR35374P 7.0±0.2 1.5 12.35±0.2 11.75±0.2 10.35±0.2 9.75±0.2 15 5.25± 0.4±0.05 0.2 - cross section 7.2±0.2 8.2±0.2 10.0±0.2 1 0.6±0.05 12.35±0.05 10.35±0.05 5.25±0.05 11.75±0.05 9.75±0.05 0.8±0.05 1.5±0.1 1.8±0.1 4.0±0.1 2.1±0.1 1.4±0.2 0.8±0.1 R 0.2 Note 1) 1.875 Note 1) 0.8 0.3±0.05 17.0±0.2 26.5 24.1 20.1 17.4 10.8±0.2 16.7±0.2 Note 1) 1.15 Note 1) 2.3 3.8 Note 1) (5.3) (6.3) 5.9 1.5±0.1 4.4±0.2 1.5±0.2 R 0.5 1.1±0.1 Battery terminal 1.9±0.05 Through hole 3.7±0.1 1.9 11.8±0.1 16.7±0.05 2.7 2.9±0.1 (1.5) Please make pattern both side of PC board Notes) 1. The position of the cross-manufacturer mating error 2. Since product bottom is a metal shell, do not make pattern circuits (to prevent shorting). ll Rights Reserved COPYRIGHT Matsushita Electric Works, Ltd.
XR(3/5) Plug (cable connection ) () (assembled condition) XR30394 Note) 1.875 Note) 0.75 Note) 1.15 0.50±0.1 Note) 2.25 Note) 2.35 Note) The position of the cross-manufacturer mating error 15 23.7 20.5 16.3±0.2 7.8 48.4 7.6 34.2 28.9 5.5 8.9 15.0 19.0 21.7 11.7 No. of signal terminal ( ) Terminal No.1 Terminal No.22 Battery contacts Battery contacts Signal terminals 4. s /On board mounting ( ) XR51228P - cross section 1.8±0.05 0.2 1 5.0 15.0±0.05 1.9±0.1 2.7±0.1 2.9±0.1 (1.5) Please make pattern both side of PC board Notes) 1. The position of the cross-manufacturer mating error 2. Since product bottom is a metal shell, do not make pattern circuits (to prevent shorting). ll Rights Reserved COPYRIGHT Matsushita Electric Works, Ltd.
XR(3/5) () XR51224P Terminal No.22 7.2±0.2 7.0±0.2 15 0.2±0.05 15.3±0.2 15.7±0.2 Terminal No.1 - cross section 1.5±0.05 0.2 1 1.9±0.1 5.0 15.0±0.05 (1.5) 2.7±0.1 2.9±0.1 Both side of PC board 0.6 15.0±0.2 4.4±0.2 1.2±0.1 Notes) 1. The position of the cross-manufacturer mating error 2. Since product bottom is a metal shell, do not make pattern circuits (to prevent shorting). (battery terminal 3 contacts) ( ) XR35371P - cross section Battery terminal 1.8±0.05 10.9±0.05 0.8±0.05 9.5±0.05 8.9±0.05 1 0.2 5.0 15.0±0.05 1.9 2.9±0.1 (1.5) 2.1±0.1 4.0±0.1 2.7 Please make pattern both side of PC board Notes) 1. The position of the cross-manufacturer mating error 2. Since product bottom is a metal shell, do not make pattern circuits (to prevent shorting). No. of signal terminal ( ) Terminal No.1 Battery contacts s Terminal No.22 Battery contacts ll Rights Reserved COPYRIGHT Matsushita Electric Works, Ltd.
XR(3/5) Plug (cable connection ) () (assembled condition) XR30341 XR30343 15 2.35 Notes) 1. The drawing shows XR30344. (External dimensions are the same also for XR30341.) 2. The position of the cross-manufacturer mating error 23.7 20.5 14.6±0.2 7.8 48.4 7.6 34.2 28.9 8.9 5.5 0.65 15.0 19.0 21.7 11.7 Plug (Board mounting ) () XR30345 Terminal No.1 2 18.0 10.50± 0.20±0.05 Terminal No.22 2.5±0.1 2±0.1 17.6±0.1 10.50±0.05 0.50±0.05 5.0±0.2 1.5±0.2 13.3 16.0 16.5 ±0.1 1.8±0.1 (7.0) 0.4±0.1 R0.2 R0.8 0.9 dia. (hole) 12.00±0.05 17.85±0.05 3.3±0.1 5.3±0.1 ±0.05 (14.6±0.2) 16.0±0.2 14.6±0.2 Please make pattern both side of PC board 4.8 0.8±0.1 1.4±0.1 Shell SMD portion 12.0±0.2 17.85±0.2 2.35±0.2 1.59±0.2 (10.0) 1.2±0.1 Note) This product is not compatible with mismatch prevention keys. ±0.2 10.0±0.2 - cross section 0.70±0.1 dia. (6.0) (6.5) ll Rights Reserved COPYRIGHT Matsushita Electric Works, Ltd.
0.7±0.1 dia. XR(3/5) Plug (Board mounting ) ( ) XR3034 12.55 B 20.8 18.0 15 0.2±0.05 4.4 B 1.5±0.2 13.8 17.0 2.5±0.1 ±0.1 1.8±0.1 R0.2 R0.8 22.8±0.1 17.6±0.1 14.0±0.05 1 0.50±0.05 0.9±0.05 dia. (hole) 2.5±0.1 5.0±0.1 +0.1 0 8.0 5.5±0.2 0.4±0.1 17.85±0.05 (7.5) (14.6±0.2) 16.0±0.2 14.6±0.2 4.8± 2.35±0.2 Both side of PC board Shell SMD portion 17.85±0.2 0.8± 1.1± 1.59±0.2 1.2±0.1 10.5 - cross section 8.0 ±0.2 15.5±0.2 B-B cross section () (4.4) 14.0±0.2 5. s 24 contacts/on board mounting ( ) XR51248P 7.2±0.2 7.0±0.2 11.5± 0.2±0.05 16.3±0.2 16.7 Note 1) 4.8 Note 1) 4.8 - cross section 1.8±0.05 0.2 11.5±0.05 0.50±0.05 5.0 9.0 1 16.0±0.05 1.9 2.7 (1.5) 2.9 Please make pattern both side of PC board 1.5±0.1 16.0±0.2 4.4±0.2 (#) The dimensions for the improper connection prevention key are set by the customer. Notes) 1. The position of the cross-manufacturer mating error 2. Since product bottom is a metal shell, do not make pattern circuits (to prevent shorting). ll Rights Reserved COPYRIGHT Matsushita Electric Works, Ltd.
(Battery terminal 3 contacts) ( ) XR35471V Note 1) Note 1) - cross section 1.8±0.05 11.4±0.05 10.0±0.05 9.4±0.05 11.5±0.05 0.8±0.05 0.2 5.0 *1.9 16.0±0.05 XR(3/5) 2.9±0.1 (1.5) 2.1±0.1 * 4.0±0.1 *2.7 Please make pattern both side of PC board Notes) 1. The position of the cross-manufacturer mating error 2. Since product bottom is a metal shell, do not make pattern circuits (to prevent shorting). Plug (cable connection ) () (assembled condition) XR30444 2.35 Note) The position of the cross-manufacturer mating error 11.5± 23.7 20.5 15.6±0.2 Note) 4.8 Note) 4.8 7.8 48.4 7.6 34.2 28.9 5.5 8.9 0.65 15.0 19.0 21.7 11.7 No. of signal terminal ( ) Terminal No.1 Battery contacts s Terminal No.24 Battery contacts ll Rights Reserved COPYRIGHT Matsushita Electric Works, Ltd.
XR(3/5) 6. s 26 contacts/on board mounting ( ) XR51268P 7.2±0.2 7.0±0.2 17.8±0.2 12.5± 0.2±0.05 17.3±0.2 17.8 1.8±0.05 0.2 17.0±0.05 12.5±0.05 5.0 9.0 1 Please make pattern both side of PC board 2.7±0.1 2.9±0.1 1.9±0.1 (1.5) 0.8 0.65 14.5 10.5 10.5 14.5 17.0±0.2 3.5 4.4±0.2 1.5±0.1 Note) Since product bottom is a metal shell, do not make pattern circuits (to prevent shorting). - cross section Plug (cable connection ) () (assembled condition) XR30541 0.50±0.1 2.35 Note) This product is not compatible with mismatch prevention keys. 12.5± 25.7 22.5 16.7±0.2 7.8 48.4 7.6 34.2 28.9 8.9 5.5 0.65 17.0 2 23.7 11.7 ll Rights Reserved COPYRIGHT Matsushita Electric Works, Ltd.
0.7±0.1 dia. Plug (Board mounting ) () XR30545 XR(3/5) 11.5 2 20.0 12.5± 0.2±0.05 1.5±0.2 13.3 16.0 ±0.1 1.8±0.1 2.5±0.1 0.4±0.1 R0.8 24.0±0.1 20.6±0.1 12.5±0.05 0.50±0.05 R0.2 0.9±0.05 dia. (hole) 19.85±0.05 16.6±0.2 2.35±0.2 4.8±0.1 ±0.1 5.0±0.1 1.59±0.2 8.0 +0.1 0 16.0±0.2 19.85±0.2 0.8± ± (10.0) 8.0 ±0.2 (7.0) (16.6±0.2) 18.0±0.2 5.0±0.2 Shell SMD portion 1.2±0.1 - cross section 15.0±0.2 (3.5) Please make pattern both side of PC board Note) This product is not compatible with mismatch prevention keys. No. of signal terminal ( ) Terminal No.1 s Terminal No.26 ll Rights Reserved COPYRIGHT Matsushita Electric Works, Ltd.
XR(3/5) 7. s 50 contacts/on board mounting ( ) XR51508P 5 (Terminal portion) 33.5 Terminal No.1 27.4 30.0±0.2 27.4 23.4 23.4 28.85 30.3 24.5 0.3±0.1 Lot display 6.0 2.75±0.2 7.2 8.0 3.5 3.85 2.0 3.65 Retention fitting 0.2±0.05 Terminal No.50 - cross section 2.1± 2-4.1±0.05 2-2.5±0.05 (hole) PC board both sides hole structure (MIN. 32.6) 30.3±0.05 (MX. 25.3) 24.5±0.05 (0.27) (0.27) (R) +0.1 2-0.55 0.05 (hole) 2.15±0.05 PC board edge Pattern forbidden area Notes) 1. The values in parenthesis are reference dimensions. 2. To reinforce the shell portion of the receptacle, have the shell guided by the casing in some way. The gap between the device casing and receptacle should be constructed to be very small, for example, under 0.1 mm. 3. The dimensions of the cross-manufacturer mating error. 2.3±0.05 (0.3) 7.75 4.8 2.8 Plug (cable connection ) ( ) (assembled condition) XR5256S XR5257S Incorrect mating prevention key Terminal No.1 Note 2) 37.7 34.3 29.9 Terminal No.50 8.0 2.7 30.0 5.5 7.6 3.4 (30.2) () 14.2 31.5 35.8 10.7 (23.7) Notes) 1. The values in parenthesis are reference dimensions. 2. The dimensions of the cross-manufacturer mating error. ll Rights Reserved COPYRIGHT Matsushita Electric Works, Ltd.
Plug (Board mounting ) XR30645 Terminal No.1 11.5 8.72 Shell SMD portion 12.0±0.2 5.4 0.6±0.2 C 0.7±0.1 dia. 2.1 39.0 36.0 25.3 24.5 0.2±0.05 16.0 24.0 29.9 31.35 32.9 28.0±0.2 35.85 5.0±0.2 C 0.8±0.2 ±0.2 6.55 Terminal No.50 - cross section 1.5±0.2 12.0 1 4.8±0.2 1.4 C 2.7 R0.3 1.2±0.1 3.3±0.2 XR(3/5) 0.9±0.05 dia. (hole) Both side of PC board Notes) 1. The values in parenthesis are reference dimensions. 2. To reinforce the shell portion of the receptacle, have the shell guided by the casing in some way. The gap between the device casing and receptacle should be constructed to be very small, for example, under 0.1 mm. 3. The dimensions of the cross-manufacturer mating error. PPLICTIONS Products can be made to match your applications, so please contact us if necessary. 1. For cdma-one 2. SMD with retention 3. With battery and charging fitting terminals 4. With compact battery terminal 5. Difference in battery terminal number 6. products (18, 22, 24 and 26 contacts) products (50 contacts) ll Rights Reserved COPYRIGHT Matsushita Electric Works, Ltd.
XR(3/5) EMBOSSED TPE DIMENSIONS (unit: mm) Tape dimensions (Conforming to JIS C 0806, 1995. However, some tapes have mounting hole pitches that do not comply with the standard.) Reel dimensions (Conforming to JIS C 0806, 1995) ±0.3 B C 1.75 E +2 0 Top cover tape Pull-out direction 4 2 D F Embossed carrier tape 1.5 ±0.1 0 dia. 1. Ultra low profile system connector 18, 22 and 24 contacts I/O connector for portable equipment 18, 22, 24 and 26 contacts I/O connector for portable equipment 50 contacts B C D E F Quantity per reel 44.0 40.4 20.2 16.0 44.4 370 dia. 700 32.0 28.4 14.2 16.0 32.4 370 dia. 1,000 44.0 40.4 20.2 16.0 44.4 370 dia. 750 2. Plug (PC board mounting ) B C D E F Quantity per reel 22 and 26 contacts 44.0 40.4 20.2 24.0 44.4 370 dia. 500 50 contacts 56.0 52.4 26.2 24.0 56.4 370 dia. 500 Connector orientation with respect to direction of progress of embossed tape Type Ultra low profile I/O connector for portable equipment Direction of tape progress Plug (Board mounting ) Regarding general notes, please refer to page 14. For other details, please verify with the product specification sheets. ll Rights Reserved COPYRIGHT Matsushita Electric Works, Ltd.