Xitanium LED driver Datasheet Xitanium Prog/Prog+ LED Xtreme drivers Xitanium Prog/Prog+ LED Xtreme drivers Philips Xitanium Prog/Prog+ Prograable LED drivers are specifically designed to deliver the highest performance, protection and configurability. The portfolio offers both central and standalone diing protocols further increasing the energy savings and O2 reductions achieved with LED lighting. The Xtreme technology ensures maximum robustness and protection combined with a very long lifetime. enefits Features Application Ultimate robustness, offering peace of mind and lower High surge protection (M/DM) Road and street lighting Long lifetime and robust protection against moisture, vibration and temperature Area lighting onfigurable operating windows (AO) Industrial lighting maintenance costs Fully prograable LED-drivers designed for the new digital and connected lighting world Multiple control interfaces: DALI, 1-10V (Prog+ : also AmpDim) Extended diagnostics via MultiOne Autonomous diing via integrated DynaDier Easy to design-in, configure and install Suitable for D operation Energy savings through high efficiency and via multiple Thermal protection for driver and for module (MTP) diing options onstant Light Output (LO) Adjustable Start-up Time (AST) End-Of-Life indicator (EOL)
Electrical input data Rated input voltage range 120...277 Vac Performance range Rated input voltage 230 Vac Rated input frequency range 50...60 Hz Performance range Rated input current 0.37 A Max. input current 0.79 A @ rated output power @ minimum performance input voltage Rated input power 85 W Power factor 0.97 Total harmonic distortion 9 Efficiency 91 Rated input voltage D range 186...250 Vdc Performance range Input voltage A range 108...305 Vac Operational range Input frequency A range 45...66 Hz Operational range Input voltage D range 168...275 Vdc Operational range Standby Power (TD) 0.45 W Isolation input to output Electrical output data Regulation method onstant urrent Output voltage 80...152 Vdc Output voltage max. 160 V Peak voltage at open load Output current 0.05...0.7 A Full output current setting Output current min prograable 200 ma Output current min diing 50 ma Output current tolerance ±5 Output current ripple LF 15 Output current ripple HF 15 Output power 4.5...75 W Full output ontrol method 1-10V, DALI, Dynadier Diing range 10...100 Galvanic Isolation Ripple = peak / average Electrical data controls input Output current amplitude diing, DALI acc. IE62386-102/207; 1-10V acc. IE60929 Default range Logistical data Product name Order code 871829111887900 Logistic code 12N 9290 007 02302 EAN3 8718291999799 Pieces per box 10 2/8
Wiring & onnections Input wire cross-section 0.82 2 solid wire, double-insulated 18 AWG solid wire, double-insulated Input wire strip length 8...12 Output wire cross-section 0.82 2 solid wire, double-insulated 18 AWG solid wire, double-insulated Output wire strip length 8...12 Maximum cable length 10000 Maximum NT output cable length 0.6 m Total length of wiring including LED module, one way Insulation Insulation Mains Mains LED + NT DALI/1-10V Housing LED + NT DALI/1-10V Housing Dimensions and weight Length (A1) 240.5 Width (1) 59.8 Width (2) 42.88 Height (1) 37.6 Fixing hole diameter (D1) 6 Fixing hole distance (A2) 226 Weight 1270 gram 3/8
Operational temperatures and humidity Ambient temperature -40...+55 Higher ambient temperature allowed as long as Tcase-max is not Starting Ambient temperature -40...+55 Tcase-max 80 Maximum temperature measured at Tcase-point Tcase-life 70 Measured at Tcase-point Maximum housing temperature 110 In case of a failure Relative humidity 10...90 Non-condensing Ambient temperature -40...+80 Relative humidity 5...95 Non-condensing Driver lifetime 100,000 hours Measured temperature at Tcase-point is Tcase-life. exceeded. Storage temperature and humidity Lifetime Maximum failures = 10 Prograable features Remark Set output current (AO) Prograable, Rset1 See Design-in guide. Default output current: = 700 ma LED module temperature derating (MTP) onstant Lumen Over Lifetime (LO) D emergency diing (DemDIM) No Diagnostics Adjustable Start-up Time AST 1-10V minimum dim level Integrated Dynadier End Of Life indicator Driver will not automatically dim when D input voltage is applied. Prograed AO value will be maintained. 4/8
Features Open load protection Remark Short circuit protection Over power protection Hot wiring No Suitable for fixtures with protection class I per IE60598 Over temperature protection driver Overheating protection ertificates and standards Approval marks / / E / SA / ENE / UL Ingress Protection classification Inrush current Inrush current Ipeak 108 A Input voltage 230V Inrush current Twidth 140 µs Input voltage 230V, measured at 50 Ipeak Drivers / M 16A type 7 pcs M Rating Relative number of LED drivers 10A 63 13A 81 16A 100 (stated in datasheet) 20A 125 25A 156 10A 104 13A 135 16A 170 20A 208 25A 260 Driver touch current / protective conductor current Typical touch current (ins. lass II) < 0.7 ma peak Acc. IE61347-1. LED module contribution not included Mains surge iunity (diff. mode) 3 Acc. IE61000-4-5. 2 Ohm, 1.2/50us, 8/20us Mains surge iunity (co. mode) 3 Acc. IE61000-4-5. 12 Ohm 1.2/50us,8/20us ontrol surge iunity (diff. mode) 0.5 Acc. IE61000-4-5. 2 Ohm, 1.2/50us, 8/20us ontrol surge iunity (co. mode) 3 Acc. IE61000-4-5. 12 Ohm 1.2/50us,8/20us DALI surge iunity (co. mode) 3 DALI - L/N acc. IE61000-4-5. 12 Ohm, 1.2/50us, 8/20us Surge iunity 5/8
Additional information Default setting Remark AO 700 ma LO OFF MTP ON Dynadier OFF EOL OFF 1-10V ON Graphs Operating window Thermal Guard 6/8
Power factor versus output power Efficiency versus output power THD versus output power 7/8
Iout as function of 1-10V interface Notes Installation & Application Notes: 1: y factory default, the 1-10V interface is enabled and DALI interface is disabled. These controls are mutually exclusive. 2: Integrated Dynadier cannot be overruled by DALI. These controls are mutually exclusive. 3: Driver is for built-in use only and must not be exposed to the elements such as snow, water and ice or to any other chemical agent which can be expected to have an adverse effect on the driver (e.g. corrosive environments). It is the responsibility of both luminaire manufacturer and installer to prevent exposure. oon sense needs to be used in order to define the proper luminaire or application IP rating. 4: Suitable for UL Damp & Dry locations 5: IE: driver housing is not allowed to be connected to accessible insulation lass II luminaire parts. Driver is suitable for insulation lass I application only. 6: Standard lead length on all wires: 500 +/- 30 solid copper. Insulation rating: 105 /600V. 7: Driver complies with the requirements of UL, SA, E, ENE, ISPR15, F 47FR15 lass A 2017 Philips Lighting Holding.V. All rights reserved. This document contains information relating to the Philips Lighting portfolio, intended for companies who may be interested in developing their product offering. Note that the information provided is subject to change. Philips Lighting does not give any representation or warranty as to the accuracy or completeness of the information included herein and shall not be liable for any action in reliance thereon. The information presented in this document is not intended as any coercial offer and does not form part of any quotation or contract. Date of release: April 24, 2017 www.philips.com/technology