intellaspot XT-1 Map Level 2 Level 3 Option/Setting Description/tes DMX ADDRESS Set DMX Start Channel: ### 1 474 Sets the first value of a unique 39-channel range on DMX link. Factory Default Settings: XXXXX Reset OFF Indicates factory default change Reverts to default setting Pan/Tilt Swap: Restores default Pan and Tilt Swaps the Pan and Tilt Motion Pan Invert: Restores default Pan direction Inverts Pan motor direction Tilt Invert: Restores default Tilt direction Inverts Tilt motor direction Display at full brightness Display Level: 14 1 Reduces brightness in 14 steps Display off when menu is locked Panel LEDs at full brightness Set Parameters LED Level 14 1 Reduces brightness in 14 steps Panel LEDs off when menu is locked. te: Blue Power LED dims but does not turn off. Disables lamp life tracking Lamp Life Limit: Tracks lamp operation time and sends a warning when the lamp approaches it s rated life limit. Lamp Level Econo Mode Standard Mode Operates lamp at 700W Operates lamp at 850 W Data Loss Timeout: Short Long Shutter closes 1 second after data loss. Shutter closes on shutdown. Auto Strikes the lamp when DMX is applied. Lamp Strike Mode Power Manual Strikes the lamp when power is applied. Leaves the lamp off until you send a lamp strike command from the DMX controller. Data Source DMX WiFi NetWork Selects the Data Source from the installed options on this unit. Mode Crossload Firmware: Safe setting Uploads fixture software to all intellaspot XT-1 fixtures on the link.
Level 2 Level 3 Option/Setting Description/tes Test Options Home Fixture: Lamp State: Copy Boot: Self Test Display Test Setup Motors Encoders Code Pan Tilt DIM Cyan Magenta Yellow CTO Gobo 1 Gobo 2 Animation Iris Soft Edge Effect Focus Zoom All Homes all fixture functions Indicates or turns lamp off Indicates or turns lamp on Does nothing when selected Copies boot code to fixture Tests motion functions Tests the mechanical function of separate wheels, flags and iris movement. te: Effect designates the 4-facet prism wheel. Tests all functions in sequence Default Safe setting Performs Display test Default Safe setting Runs motor setup routine Leaves encoders enabled Disables encoders For factory use only
Level 2 Level 3 Option/Setting Description/tes Sensor Status Unique Number ########## DMX Values By Channel Pan Encoder Tilt Encoder 1:### ### ### 4:### ### ### Pan Pan Fine Tilt Tilt Fine Mix Color Cyan Magenta Yellow CTO Position Gobo 1 Gobo 1 Position Fine By Parameter Gobo 2 Gobo 2 Position Fine Effect Effect Rotate Effect Rotate Fine Animate Animate Rotate Soft Edge Focus Focus Focus Fine Zoom Zoom Fine Iris Locates Pan position Locates Tilt position Displays fixture s unique 10-character number Displays current values for all channels in groups of six DMX values per screen Displays current DMX decimal value of each of the 39 channels used by the intellaspot XT-1 fixture
Level 2 Level 3 Option/Setting Description/tes DMX Values Temperatures Fan Speed Fixture Hours: Lamp Shutter Dim M Speed Macro By Parameter Control DMX Breaks DMX Framing Err DMX Overrun Err DMX Start Channl Current Temp Topbox: ###C Maximum Temp Minimum Temp Temperatures Reset Topbox: ###C Topbox: ###C YES LPS: ###RPS Optics: ###RPS Lamp : ####RPS Displays current DMX decimal value of each of the 39 channels used by the intellaspot XT-1 fixture Monitors the DMX stream for transmission errors Displays temperature in degrees Celsius for the Electronics Housing (topbox) and the Head. Select YES and press Enter for 5 seconds to reset all sensors to Current Temperature Displays current speed of the electronics housing fan and the fans in the fixture head Displays fixture operation time in hours:minutes Fixture Hours Reset: YES Default safe setting Press Enter for 5 seconds to reset fixture hours to 0
Level 2 Level 3 Option/Setting Description/tes Lamp Hours: Lamp Strikes: Lamp Hr/Strike Reset: ### Lamp Status: Display Errors YEs Lamp Lamp Lamp Striking Lamp Error XXXXXXXXXXXXX XXXXXXXXXXXXX Lamp operation time in hours:minutes Current number of lamp strikes Default safe setting Press Enter for 5 seconds to reset fixture hours to 0 Current lamp status Scrolls through errors displayed in 2-line, 16-character format Software Version: L##.##.### Status Major.Minor.Build Module Version Channels Needed: ## Next DMX Channel: ## Pan Tilt Animate/FX Dim/Cyn/CTO/Iris Dim/Mag/Yel/Clr Litho1/Litho2 Focus/Frost/Zoom Display L##.##.### Displays the Hardware and Software versions for each logic board in the fixture. Status Major.Minor.Build Displays channel range for the unit as configured Current channel range + 1 te: The display reads Link Full if there is not a sufficient channel range remaining on the DMX link.