300M Wireless-N Broadband Router Model No.: ib-wrb314n User Manual Ver.: 1.0.0
Contents...Error! Bookmark not defined. Chapter 1 Product Overview... 3 Package Contents 3 Conventions....4 Panel Overview... 4 Chapter 2 Installation... 6 Chapter 3 Internet Connection Setup... 7 3.1 Login to Router... 7 3.2 Quick Setup... 7 3.3 Quick Setup Internet Connection Setup. 8 3.5 Quick Setup - Wireless Setup... 8 3.6 Quick Setup Manual Setup... 9 3.7 Wireless Repeater... 10 3.8 Wireless WISP (Wireless Internet Service Provider) 11 Chapter 4 Network Settings... 14 4.2 WAN... 14 4.3.PPPoE... 15 4.4 Static IP... 15 4.5 Dynamic IP... 16 4.6 MAC Cloning... 16 Chapter 5. Security... 17 5.1 IP Filtering... 20 5.2 MAC Filtering... 21 5.3 Port Forwarding... 21 5.4 URL Filtering 22 5.5 DMZ... 23 5.6 QoS...... 24 5.7 Routing... 24 Chapter 6. Maintenance... 25 Chapter 7. Status Info.... 26 Contact Information... 27 2
Chapter 1 Product Overview iball Baton 300M Wireless-N Broadband Router complies with IEEE 802.11 b/g/n wireless standards. Enhanced Wireless Transmission speed up to 300Mbps Integrates 4-10/100Mbps LAN ports & 1 - WAN port. Multi-Operation Modes - Wireless Router / WISP / Repeater WISP Internet - Configure Internet through wireless mode 5dBi x 2 Omni-directional Antenna Package Contents The following items should be found in your package: 300M Wireless-N Broadband Router 1 x QIG 1 x RJ45 Patch Cord 1 x DC Power Adapter Product Feature: Complies with IEEE802.11b/g/n, IEEE802.3 & IEEE802.3u standards With 4-10/100M LAN ports, 1- WAN port & Wireless-N AP Operation Mode: Router / WISP / Repeater Broadband Internet: PPPoE, Static IP, Dynamic IP connection type With Security feature such as IP, MAC and domain filtering With WEP, WPA-PSK, WPA2-PSK encryption security Built-in NAT, DHCP Server, Virtual server, DMZ and UPnP Web-based management 5dBi Omni-Directional Antenna Power Adapter: 5V DC, 1000mA 3
Conventions 300M Wireless-N Broadband Router (ib-wrb314n) The Router or ib-wrb314n mentioned in this guide stands for iball Baton 300M Wireless-N Broadband Router without any explanation. 1.2 Panel Overview LED overview: LED Status Colour Description PWR Steady Red led Router is ON & functioning properly Blue Led Steady Wireless on & WLAN Steady / no Data Transmission / Blinking Blinking on Data Transmission WAN Blinking Green Led Functioning properly WPS Blinking Green Led WPS ON 4
Port/Button Overview: 300M Wireless-N Broadband Router (ib-wrb314n) Port/Bu tton WAN LAN RESET PWR Description Internet port connecting to a DSL/Cable modem or ISP directly. For connection to a computer or router. Pressing this button for 7 seconds restores the device to factory default settings. Power Adapter. Do not use a different power adapter than the included one. 5
Chapter 2 Installation 1. Connect one end of the included power adapter to the router and then plug the other end into a wall outlet nearby. 2. Connect the LAN port on the Router to the NIC port on your PC using an Ethernet cable. 3. Connect the WAN port on the Router to an Internet-enabled Cable/xDSL modem using an Ethernet cable. 4. Switch on the Router 6
Chapter 3 Internet Connection Setup 300M Wireless-N Broadband Router (ib-wrb314n) 3.1 Login to Router 1. Configuring the router via Web based configuration To login to the router, you should set up the TCP/IP Protocol in "Obtain an IP address automatically" mode on your PC(s). 2. To access the configuration GUI, open a web-browser and type in the default address of the router http://192.168.1.1 3. Type username admin and password admin and then click Log in to go to interface below: Note: Web-based utility can be used on any Windows, Macintosh or UNIX OS with a Web browser, such as Microsoft Internet Explorer 8.0 / 9.0 (Suggested) & Mozilla Firefox. 3.2 Quick Setup Default page shows quick Setup steps to configure the router quickly and easily Click the below Operation modes to configure the router settings 7
Auto Detect Manually 3.3 Quick Setup Internet Connection Setup 3.4 Quick Setup In this page, the device enables to make configure WAN Setup. Configuring Internet Connection Set the router WAN As per ISP requirement Dynamic IP / Static IP / PPPoE / PPTP / L2TP Settings provided by your Internet Service Provider which will enable Internet access to router and wireless Click Next button 3.5 Quick Setup - Wireless Setup 8
Set Wireless SSID, Wireless Security, Pre-shared Key & Click on Save 3.6 Quick Setup - Manual Setup Internet Connection Setup Configuring Internet Connection Setup Set the router WAN As per ISP requirement Dynamic IP / Static IP / PPPoE / PPTP / L2TP Settings provided by your Internet Service Provider which will enable Internet access to router and wireless If your ISP offer you automatic IP address on DHCP Select Dynamic IP. In this page, the device enables to make configure WAN Setup. Router Internet WAN settings can be configured with different connection mode as details provided by your ISP. Static IP Select static IP, if your ISP is using STATIC IP connection mode. Enter WAN IP address, Subnet Mask, Default Gateway, DNS. Click the SAVE button to save your settings. Dynamic IP Select Dynamic IP as per your ISP details provided. Click the SAVE button to save your settings. We recommend you to setup a wireless security key on this interface to protect your wireless network from undesired access. Then click the OK button to save your settings. 9
PPPoE Select PPPoE, if your ISP are using a PPPoE connection and enter the PPPoE user name and password provided by your ISP. Then setup a wireless security key on the interface below to secure your wireless network. At last, click the SAVE button to save your settings. the default Internet connection type is DHCP. If your ISP offers you static IP Internet connection type Static IP Address, select Static IP" from Mode drop-down menu and then enter IP address, subnet mask, Primary DNS and secondary DNS information provided by your ISP into corresponding fields. WAN Access Type: Displays the current Internet connection type. IP Address: Enter the WAN IP address provided by your ISP. Inquire your ISP if you are not clear. Subnet Mask: Enter WAN Subnet Mask provided by your ISP. The default is 255.255.255.0. Default Gateway: Enter the WAN Gateway provided by your ISP. Primary DNS Server: Enter the necessary DNS address provided by your ISP. Secondary DNS Server: Enter the secondary DNS address if your ISP provides, and it is optional. MTU: Maximum Transmission Unit. DO NOT change it from the factory default of 1500 unless necessary. You may need to change it for optimal performance with some specific websites or application software that cannot be opened or enabled. WAN Access Type: PPPoE. User Name: Enter the PPPoE User name given by your ISP. Password: Enter the password provided by your ISP. 3.7 Wireless Repeater 10
Wireless Repeater Mode Wireless Repeater is a device that allows wireless to boost the existing wireless network and allows devices to connect to a network using WiFi. Wireless devices will able to communicate over network through Wireless Repeter SSID: Default SSID of router is iball-baton Pre-Shared Key: You can configure security key to protect your wireless security. 3.8 Wireless WISP (Wireless Internet Service Provider) ***To configure WISP you have to configure Internet settings first Set the router WAN As per ISP requirement Dynamic IP / Static IP / PPPoE / PPTP / L2TP Settings provided by your Internet Service Provider which will enable Internet access to router and wireless In this mode, the Wireless works as a WAN port to connect to remote SSID to configure WISP function. Configuring WISP function Wireless ISP: Click Enable button to configure WISP. 11
Site Survey: Click site survey button to view remote SSID Enter the remote wireless Pre-shared key & click SAVE button 3.9 Wireless Basic Settings In this page, the device enables to make configure Wireless Basic Settings.. 12
Configuring Wireless Basic Settings Set SSID: Set the SSID Network Mode: Automatic (802.11b/g/n) Channel No: Auto Configuring Multi SSID Enable SSID1 Set SSID: Set the SSID Configuring Wireless Security Setup Encryption: WPA2 (AES) Pre-shared-Key-Format: Passphrase Pre-shared-Key: Set the wireless password (Key) to connect and access wireless SSID 13
Click Finish to complete the Quick Configuration. Now you can power off and power on the router and can connect to SSID using the password which you have set previously. Chapter 4 Network Settings 4.1 Network Settings LAN Configuring LAN Setup Set the router LAN IP Address and Subnet Mask of the router for Local Access. In this page, the device enables to make configure LAN Setup. Select the option Network settings > WAN to Configure Internet connection type. 4.2 WAN There are 3 Internet connection types available for your selection: PPPoE, Static IP,Dynamic IP. Select your Internet connection and follow corresponding instructions for internet connection configuration. 14
4.3. PPPoE 300M Wireless-N Broadband Router (ib-wrb314n) Select PPPoE, if your ISP are using a PPPoE connection and provide you with PPPoE user name and password information. WAN Access Type: Displays current Internet connection type. User Name: Enter the user name provided by your ISP. Password: Enter the password provided by your ISP. Service Name: Description of PPPoE connection. Leave blank unless necessary. Note: To activate the Connect on Demand" feature, you must first configure current time on the "Time Zone Settings screen under "Maintenance" menu. 4.4 Static IP If your ISP offer you static IP Internet connection type, select Static IP" from Mode drop-down menu and then enter IP address, subnet mask, Primary DNS and secondary DNS information provided by your ISP into corresponding fields. 15
WAN Access Type: Displays the current Internet connection type. IP Address: Enter the WAN IP address provided by your ISP. Inquire your ISP if you are not clear. Subnet Mask: Enter WAN Subnet Mask provided by your ISP. The default is 255.255.255.0. Default Gateway: Enter the WAN Gateway provided by your ISP. Primary DNS: Enter the necessary DNS address provided by your ISP. Secondary DNS: Enter the secondary DNS address if your ISP provides, and it is optional. 4.5 Dynamic IP Select this option if your ISP does not give you any IP information or account information. You don t need to configure any settings for this connection. MTU: Maximum Transmission Unit. DO NOT change it from the factory default of 1500 unless necessary. You may need to change it for optimal performance with some specific websites or application software that cannot be opened or enabled. 4.6 MAC Cloning This section allows you to configure router s WAN MAC address. Some ISP may require binding an accepted MAC address for communication. If the bound MAC address differs from your router s predefined WAN MAC address, then you need to replace the router s WAN MAC with the bound MAC for achieving valid communication with your ISP. MAC Address: Configure router s WAN MAC address. MAC Address Clone: Clicking this button changes router s WAN MAC address from default to the MAC address of the PC you are currently on. Don t use this button unless your PC s MAC address is the one bound by your ISP. Reset: Restores router s WAN MAC to default settings. 16
5. Chapter 5. Security 300M Wireless-N Broadband Router (ib-wrb314n) URL filtering, Virtual Server, DMZ, Remote Management, Ping settings can be configured through menu WAN Ping & Static routing if required in your network need to be configured through static routing menu. Routing table will show the routing status. 5.1. IP Filtering IP Filtering l function will help to filter the access of your network. 5.2. MAC Filtering MAC Filtering l function will help to filter the access of your network. Entries in this table are used to restrict certain types of data packets from your local network passing to the Internet through the Gateway. Use of such filters can be helpful in securing or restricting your local network. 5.3 Port Forwarding 17
This function allows you to automatically redirect common network services to a specific machine behind the NAT firewall. These settings are only necessary if you wish to host some sort of server such as a web server or mail server on the private local network behind your Gateway's NAT firewall. 5.4. URL Filtering The URL filter is used to restrict LAN user s access to the internet. Block those URLs which contain listed in rules. 5.5. DMZ A Demilitarized Zone is used to provide Internet services without sacrificing unauthorized access to its local private network. Typically, the DMZ host contains devices accessible to Internet traffic, such as Web (HTTP) servers, FTP servers, SMTP (e-mail) servers, and DNS servers. 18
5.6. QoS 300M Wireless-N Broadband Router (ib-wrb314n) This function improves your online gaming experience by ensuring that your game traffic is prioritized over other network traffic, such as FTP or Web. 5.7. Routing This page is used to setup static route entry. A static route is a pre-determined path that network information must follow to reach a specific host or network. Use the Routing page to add or delete a route. 6.1. Maintenance This Page allows setting Time Zone, Firmware Upgrade, Backup & Restore, 19
Password, Diagnostic Tools, and Restart. 300M Wireless-N Broadband Router (ib-wrb314n) 7.1. Status Info. This Page shows the current status of Wireless Router. COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. iball Baton is a registered trademark of Best IT World (India) Pvt. Ltd. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from Best IT World (India) Pvt. Ltd. All rights reserved. Appendix 3: Contact Information Note: For any technical help on iball Baton products please contact support.baton@iball.co.in www.iball.co.in www.iballbaton.com 20