HD CCTV Digital Video Camera OPERATION MANUAL M133-HDX210-001 Thank you for choosing our high quality camera. Before attempting to connect or operate, please read and follow these instructions.
CAUTION These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so. Use Class 2 Power Supply Only 2
CONTENTS 1. CAUTIONS 2. IMPORTANT SAFETY INSTRUCTION 3. FEATURES 4. EQUIPMENT AND ACCESSORIES 5. CAMERA COMPONENT DESCRIPTIONS 6. INSTALLATION 7. DIMENSIONS 8. SPECIFICATION 9. OSD MANUAL 3
1. CAUTIONS This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions; 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. Note This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. WARNING This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. Caution Any changes or modifications in construction of this devices which are not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment. CAUTIONS 1. A regulated DC12V 1A power supply is recommended for use with this camera for the best picture and the most stable operation. An unregulated power supply can cause damage to the camera. When unregulated power supply is applied, product warranty will be out of subject. 2. It is recommended that the camera is used with a monitor that has a CCTV quality 75 video impedance level. If your monitor is switched to high impedance then please adjust accordingly. 3. Do not attempt to disassemble the camera to gain access to the internal components. Refer servicing to your dealer. 4. Never face the camera towards the sun or any bright or reflective light, which may cause smear on the picture and possible damage to the CCD. 5. Do not remove the serial sticker for the warranty service. 6. Do not expose the camera to rain or other types of liquid. 7. The apparatus must be connected to a mains socket-outlet with a protective earthing connection. 4
1. CAUTIONS Correct Disposal of This Product (Waste Electrical & Electronic Equipment) (Applicable in the European Union and other European countries with separate collection systems) This marking shown on the product or its literature, indicate that it should not be disposed with other household wastes at the end of its working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources. This product should not be mixed with other commercial wastes purchased this product, or their local government office, for details of where and how they can take item for environmentally safe recycling. Business users should contact their supplier and check the terms and conditions of the purchase contract. Household users should contact either the retailer where they for disposal. 5
2. IMPORTANT SAFETY INSTRUCTION 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5) Do not use this apparatus near water. 6) Clean only with dry cloth. 7) Do not block any ventilation openings. Install in accordance with the manufacturer s instructions. 8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 11) Only use attachments/accessories specified by the manufacturer. 12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. 13) Unplug this apparatus during lightning storms or when unused for long periods of time. 14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. 6
3. FEATURES High Resolution. 1/3 SONY Progressive Color CMOS Image Sensor, 1920 x 1080 60fps Support various digital video output. 720p30, 720p60, 720p25, 720p50, 1080i60, 1080i50, 1080p30, 1080p25 Video Output. Primary HD-SDI (BNC) Test / Setup TV Out (BNC), NTSC / PAL selectable. Support RS485 Communucation Protocol for Camera Configuration Remote Control. OSD menu for setup and configuration. Lens Control. Manual Iris, DC Iris (or Video Iris : factory selectable). Provides True Day/Night Capability with Motorized IR Cut Filter. Accepts CS Mount Lenses Adapter included for C-Mount Lens. Power Source DC 12V / AC 24V 7
AC 24V DC 12V 4. EQUIPMENT AND ACCESSORIES HD CCTV Digital Video Camera AUTO IRIS LENS CONNECTION PLUG C-MOUNT ADAPTOR RING OPERATION MANUAL TERMINAL BLOCK * NOTE PLEASE REMOVE PROTECTION FILM HDcctv 1.0 OUTPUT 8
5. CAMERA COMPONENT DESCRIPTIONS FRONT TRIPOD MOUNTING HOLE(1/4"-20 UNC) MOUNT COVER C-MOUNT ADAPTOR RING (Optional use for C-Mount lens only) AUTO IRIS JACK TRIPOD MOUNTING HOLE(1/4"-20 UNC) BACK FOCUS CONTROL LEVER 9
5. CAMERA COMPONENT DESCRIPTIONS BACK 1 2 5 7 4 3 HDcctv 1.0 OUTPUT 6 AC 24V DC 12V 8 11 10 9 1. MENU SET BUTTON MENU NAVIGATION BUTTONS 2. UP BUTTON 3. DOWN BUTTON 4. LEFT BUTTON 5. RIGHT BUTTON 6. POWER LED 7. SDI OUT BNC 8. VIDEO OUT BNC 9. MIC IN JACK 10. AUDIO OUT JACK (TBD) 11. TERMINAL (POWER, RS-485, Digital Input/Output) AC 24V DC 12V 10
6. INSTALLATION LENS CONNECTION Mega Pixel Lenses are sold separately. Lenses such as an auto iris lens, CS-Mount lens and C-Mount lens can be used (adapter included for C-Mount Lens). NOTE Please keep the lens clean. Any foreign objects and Finger marks on the lens can cause inferior image quality in low light level conditions. When using an auto iris lens 1. Please peel off about 8mm of the outer skin of the auto iris lens cable. 2. Please peel off about 2mm of the outer skin of the insulated conductor inside the lens cable. 11
6. INSTALLATION 3. Please remove the cover of the auto iris lens connection plug and solder the lens cable to the connector pin in the plug. * PIN ASSIGNMENT OF THE LENS CONNECTOR 1) Video auto iris lens Pin 1: Power source(dc 12V) Pin 2: N.C(Not used) Pin 3: Video signal Pin 4: Shield, GND(Ground) 2) DC auto iris lens Pin 1: DAMP-(CTL-) Pin 2: DAMP+(CLT+) Pin 3: DRV+ Pin 4: DRV-(GND) 4. Please replace the auto iris lens connection plug cover and take off the sensor protection cap and then attach the auto iris lens to the camera by screwing it in clockwise. 12
6. INSTALLATION 5. Please insert the connection plug from the auto iris lens cable into the auto lens connector, which is located on the side of the camera. *NOTE When using a CS-Mount Lens, you can attach it directly to camera. If using a C-Mount Lens, you must attach the ring spacer provided, otherwise if will crack the image sensor. C-mount lens : 10mm or less CS-mount lens : 5mm or less 13
6. INSTALLATION Installation of C-Mount Lens C-MOUNT ADAPTOR RING Installation of CS-Mount Lens 14
6. INSTALLATION MONITOR CONNECTION HDcctv DVR or Other HDcctv Signal Equipment HDcctv 1.0 OUTPUT To HD - SDI IN AC 24V DC 12V BNC FEMALE VIDEO Hand - Held Test Monitor To VIDEO IN DC12V / AC24V REGULATED POWER SUPPLY 15
7. DIMENSIONS Unit(mm) MOUNTING HOLE (1/4"-20 UNC, Depth 5) 72.5 143.5(C-Mount) 138.5(CS-Mount) 66 AUTO IRIS JACK C-MOUNT ADAPTOR RING (Optional use for C-Mount lens only) MOUNTING HOLE 16
8. SPECIFICATION Image Device Effective Pixels Unit cell size Video output mode Minimum illumination S/N Ratio Shutter speed Min. Exposure Time Flickerless True Day/Night White Balance BLC WDR Lens Control Privacy Mask OSD Menu Power Consumption Dimension (W x H x D) Weight Lens Mount Conformity Temperature/Humidity (non-condensing) SONY 1/3 Progressive Color CMOS Image Sensor 2096(H) x 1561(V) 60fps 2.5um(H) x 2.5um(V) HD-SDI : 720p30, 720p60, 720p25, 720p50, 1080i60, 1080i50, 1080p30, 1080p25 TV Out : NTSC / PAL selectable 1.0 Lux Max 50dB Auto / Manual selectable 1/10000 sec Off / 60Hz(50Hz) selectable IR Cut / Pass Filter change ATW / Manual / Specific Color / Push On / Off (by OSD) On / Off (by OSD) Manual Iris, DC Iris (or Video Iris : factory setting only) On / Off selectable & Position controlable each 15 Zone Yes DC 12V (±10%) Max. 500mA AC 24V (±10%) Max. 6W 72.5mm x 66mm x 138.5mm 450g CS / C-mount CE, FCC, KC, HDcctv Alliance Base-Line Compliance Operation : -10~50 / 20~80% Storage : -20~70 / 20~95% Specifications and designs are subject to change for improving the functionality of this product without notice. 17
9. OSD MANUAL Menu structure - Main Menu VIDEO OUT LENS EXPOSURE WHITE BALANCE DAY / NIGHT IMAGE SYSTEM - VIDEO OUT Menu VIDEO SDI RESOLUTION 1080P / 1080I / 720P SDI FRAME RATE CDBS FORMAT 1080P 1080i 720P 30HZ / 25HZ 60HZ / 50HZ 30HZ / 25HZ / 60HZ / 50HZ NTSC / PAL VIDEO APPLY 18
9. OSD MANUAL - LENS Menu LENS LENS TYPE DC IRIS (VIDEO IRIS) / MANUAL IRIS IRIS VOLUME 0 ~ 50 - EXPOSURE Menuv EXPOSURE SHUTTER SHUTTER MODE NORMAL AE / AE HOLD / MANUAL NORMAL AE AE PRIORITY NORMAL / GAIN / SHUTTER GAIN SHUTTER GAIN LEVEL 0 DB / 1.2 DB / 3.31 DB 5.12 DB / 6.92 DB / 9.33 DB / 11.14 DB / 12.94 DB / 15.34 DB / 17.16 DB / 18.96 DB / 21.37 DB / 23.18 DB / 24 DB / 27.09 DB / 29.2 DB SHUTTER LEVEL 1 ~ 160 NORMAL USER MODE 1 ~ 4 GAIN LEVEL 1 ~ 150 SHUTTER LEVEL 1 ~ 160 FLICKERLESS OFF / 50HZ / 60HZ BRIGHTNESS 0 ~ 255 AGC 0 ~ 186 BLC ON / OFF WDR ON / OFF 19
9. OSD MANUAL - WHITE BALANCE Menu WHITE BALANCE WB MODE ATW / MANUAL / SPECIFIC COLOR / PUSH ATW ATW MODE INDOOR / OUTDOOR MANUAL R GAIN 0 ~ 255 B GAIN 0 ~ 255 SPECIFIC COLOR TARGET TEMP 1500K / 1567K / 1641K / 1721K / 1810K / 1909K / 2019K / 2143K / 2283K / 2442K / 2625K / 2838K / 3088K / 3387K / 3750K / 4200K / 4773K / 5526K / 6563K / 8077K / 10500K / 15000K - DAY / NIGHT Menu DAY & NIGHT DAY & NIGHT AUTO / BW / COLOR AUTO DELAY TIME 0 SEC ~ 10 SEC DAY THRESHOLD 0 ~ 255 NIGHT THRESHOLD 0 ~ 255 20
9. OSD MANUAL - IMAGE Menu IMAGE GAMMA Y GAMMA PRESET 0 ~ PRESET 3 C GAMMA PRESET 0 ~ PRESET 3 SHARPNESS 0 ~31 CONTRAST 0 ~ 31 SATURATION 0 ~ 31 DNR OFF / LOW / MIDDLE / HIGH PRIVACY ZONE SELECT ZONE 0 ~ ZONE 14 MASK ON / OFF ON / OFF TRANSPARANT 0 / 0.5 / 0.75 / 1 COLOR WHITE / BLACK / RED / GREEN / BLUE YELLOW / CYAN / MAGENTA POSITION CONTROL V SIZE 0 ~ 1080 H SIZE 0 ~ 1920 V POSITION 0 ~ 1080 H POSITION 0 ~ 1920 MOSAIC ON / OFF MIRROR OFF / H FLIP / V FLIP / HV FLIP 21
9. OSD MANUAL - SYSTEM Menu SYSTEM FIRMWARE VER COMMUNICATION CAMERA ID NO. 0 ~ NO.255 BAUD RATE 2.4K / 4.8K / 9.6K 19.2K / 38.4K /57.6K COMM APPLY AUDIO MODE ENABLE / DISABLE FOCUS MODE ON / OFF FACTORY RESET 22
9. OSD MANUAL Main Menu MAIN MENU + VIDEO + LENS + EXPOSURE + WHITE BALANCE + DAY / NIGHT + IMAGE + SYSTEM - VIDEO : Select SDI out format and TV out format. - LENS : Select the IRIS type and adjust the IRIS control value. - EXPOSURE : Adjust exposure control. - WHITE BALANCE : Adjust white balance control. - DAY / NIGHT : Day & Night control. - IMAGE : Apply image processing effects. - SYSTEM : System information & setting. - EXIT : Close OSD Menu. 23
9. OSD MANUAL Video VIDEO OUT * SDI RESOLUTION * SDI FRAME RATE * CVBS FORMAT + VIDEO APPLY 1080p 30HZ NTSC - SDI RESOLUTION Use the LEFT/RIGHT button to select the SDI output video resolution - 720p, 1080i, 1080p * Note : When the OSD menu is not displayed on video, 720p resolution can be selected by pressing the UP button in 5 seconds. Similarly, 1080p resolution can be selected by pressisng the DOWN button in 5 seconds. - SDI FRAME RATE Use the LEFT/RIGHT button to select the SDI output video frame rate SDI resolution 1080p 1080i 720p Available frame rate 30Hz, 25Hz 60Hz, 50Hz 30Hz, 25Hz, 60Hz, 50Hz - CVBS FORMAT Use the LEFT/RIGHT button to select the TV out video format - NTSC, PAL * Note : When the OSD menu is not displayed on video, NTSC video format can be selected by pressing the LEFT button. Similarly, PAL video format can be selected by pressing the RIGHT button. - VIDEO APPLY Apply all video setting changed at once. Use the SET button to apply. - ESC Back to the prevois menu page. LENS * LENS TYPE * IRIS VOLUME LENS DC IRIS 25 - LENS TYPE Use the LEFT/RIGHT button to select the lens type for iris control. - DC IRIS(VIDEO IRIS), MANUAL IRIS. - IRIS VOLUME Use the LEFT/RIGHT button to adjust the iris volume level. Iris volume control does not apply when the LENS TYPE is set to MANUAL IRIS. 24
9. OSD MANUAL EXPOSURE EXPOSURE + SHUTTER * FLICKERLESS * BRIGHRNESS * AGC * BLC * WDR OFF 30 140 OFF OFF - SHUTTER Use the SET button to go to the SHUTTER sub menu. - FLICKERLESS Use the LEFT/RIGHT button to select the flickerless control setting - OFF, 60Hz, 50Hz. - BRIGHTNESS Use the LEFT/RIGHT button to adjust the brightness reference level. - AGC Use the LEFT/RIGHT button to adjust the AGC max value - BLC Use the LEFT/RIGHT button to select ON/OFF the Back-Light Compensation control. - WDR Use the LEFT/RIGHT button to select ON/OFF the Wide Dynamic Range effect control. 25
9. OSD MANUAL SHUTTER (Sub Menu) SHUTTER SHUTTER SHUTTER * SHUTTER MODE NORMAL AE * SHUTTER MODE NORMAL AE * SHUTTER MODE NORMAL AE * AE PRIORITY NORMAL * AE PRIORITY GAIN * AE PRIORITY SHUTTER * GAIN LEVEL 0 DB * SHUTTER LEVEL 25 SHUTTER SHUTTER * SHUTTER MODE AE HOLD * SHUTTER MODE MANUAL * USER MODE 1 * GAIN LEVEL * SHUTTER LEVEL 20 50 - SHUTTER MODE Use the LEFT/RIGHT button to select shutter & gain control mode - NORMAL AE, AE HOLD, MANUAL. - AE PRIORITY This menu can be accessed when the SHUTTER MODE is set to NORMAL AE. Use the LEFT/RIGHT button to select the AE control priority setting. - NORMAL, GAIN, SHUTTER. - USER MODE This menu can be accessed when the SHUTTER MODE is set to MANUAL. Use the LEFT/RIGHT button to select the user mode(1~4) to save setting. - GAIN LEVEL In GAIN priority mode at NORMAL AE mode. This menu can be accessed when the SHUTTER MODE is set to NORMAL AE and AE PRIORITY is set to GAIN. Use the LEFT/RIGHT button to select the Gain value setting. - GAIN LEVEL In MANUAL mode. This menu can be accessed when the SHUTTER MODE is set to MANUAL. Use the LEFT/RIGHT button to select the Gain level setting. - SHUTTER LEVEL This menu can be accessed when the SHUTTER MODE is set to MANUAL. Use the LEFT/RIGHT button to select the Shutter level setting. 26
9. OSD MANUAL WHITE BALANCE WHITE BALANCE WHITE BALANCE * WB MODE ATW * WB MODE SPECIFIC COLOR * ATW MODE INDOOR * TARGET TEMP 3387K WHITE BALANCE WHITE BALANCE * WB MODE MANUAL * WB MODE PUSH * R GAIN * B GAIN 48 64 - MODE Use the LEFT/RIGHT button to select White balance modes - ATW, MANUAL, SPECIFIC COLOR, PUSH ATW MANUAL SPECIFIC COLOR PUSH Auto trace white balance mode Manual white balance mode Manual setting with target color temperature White Balance Push mode to Auto AWB - ATW MODE This menu can be accessed when the WB MODE is set to ATW. Use the LEFT/RIGHT button to select environment setting. - INDOOR, OUTDOOR - TARGET TEMP This menu can be accessed when the WB MODE is set to SPECIFIC COLOR. Use the LEFT/RIGHT button to select target color temperature. - R GAIN This menu can be accessed when the WB MODE is set to MANUAL. Use the LEFT/RIGHT button to adjust the Red Gain. - B GAIN This menu can be accessed when the WB MODE is set to MANUAL. Use the LEFT/RIGHT button to adjust the Blue Gain. 27
9. OSD MANUAL Day / Night DAY & NIGHT DAY & NIGHT * DAY & NIGHT AUTO * DAY & NIGHT EXT * DELAY TIME 3 SEC * DAY THRESHOLD * NIGHT THRESHOLD 101 188 DAY & NIGHT DAY & NIGHT * DAY & NIGHT COLOR * DAY & NIGHT BW - DAY & NIGHT: Use the LEFT/RIGHT button to select Day & Night modes - AUTO, EXT, COLOR, BW AUTO EXT Auto controlled by AGC level in the processor. (AGC Type) Auto controlled by EXT signal. COLOR Fixed Day State. Color Image. BW Fixed Night State. BW Image. - DELAY TIME: This menu can be accessed when the DAY & NIGHT is set to AUTO. Use the LEFT/RIGHT button to select state change delay time. - DAY THRESHOLD: This menu can be accessed when the DAY & NIGHT is set to AUTO. Use the LEFT/RIGHT button to select threshold value of change from night state to day state. - NIGHT THRESHOLD: This menu can be accessed when the DAY & NIGHT is set to AUTO. Use the LEFT/RIGHT button to select threshold value of change from day state to night state. 28
9. OSD MANUAL IMAGE IMAGE + GAMMA * SHARPNESS * CONTRAST * SATURATION * DNR + PRIVACY * MIRROR 7 17 18 OFF OFF - GAMMA: Use the SET button to go to the GAMMA sub menu. - SHARPNESS: Use the LEFT/RIGHT button to adjust the sharpness value. - CONTRAST: Use the LEFT/RIGHT button to adjust the contrast value. - SATURATION: Use the LEFT/RIGHT button to adjust the saturation level. - DNR: Use the LEFT/RIGHT button to select the digital noise reduction level. - OFF, LOW, MIDDLE, HIGH - PRIVACY: Use the SET button to go to the PRIVACY MASK sub menu. - MIRROR: Use the SET button to select image flip modes. - OFF, H FLIP, V FLIP and H/V FLIP. GAMMA (Sub Menu) GAMMA * Y GAMMA * C GAMMA RPESET 2 RPESET 3 - Y GAMMA: - C GAMMA: Use the LEFT/RIGHT button to select preset gamma setting for luma. Use the LEFT/RIGHT button to select preset gamma setting for chroma. 29
9. OSD MANUAL PRIVACY MASK (Sub Menu) PRIVACY MASK * ZONE SELECT * MASK ON / OFF * TRANSPARANT * COLOR + POSITION CONTROL ZONE 0 OFF 0.5 WHITE - ZONE SELECT: Use the LEFT/RIGHT button to select the mask zone number to setting. - MASK ON/OFF: Use the LEFT/RIGHT button to select ON/OFF the mask that is zone selected. - TRANSPARENT: Use the LEFT/RIGHT button to adjust the mask transparent level. - COLOR: Use the LEFT/RIGHT button to select the mask color. - POSITION CONTROL: Use the SET button to go to the mask position setting sub menu PRIVACY MASK (Sub Menu) * V SIZE * H SIZE * V POSITION * H POSITION * MOSAIC PRIVACY MASK 0 0 0 0 OFF - V SIZE: Use the LEFT/RIGHT button to adjust the mask vertical size. - H SIZE: Use the LEFT/RIGHT button to adjust the mask horizontal size. - V POSITION: Use the LEFT/RIGHT button to adjust the mask vertical position. - H POSITION: Use the LEFT/RIGHT button to adjust the mask horizontal position. - MOSAIC: Use the LEFT/RIGHT button to select ON/OFF the mask mosaic setting. 30
9. OSD MANUAL SYSTEM SYSTEM * FIRMWARE * COMMUNICATION * AUDIO OUTPUT * FOCUS MODE * FACTORY RESET - FIRMWARE VER : Information of camera s firmware version. - COMMUNICATION: Use the SET button to go to the COMMUNICATION sub menu. - AUDIO OUTPUT: Use the LEFT/RIGHT button to select the audio output ENABLE/ DISABLE. - FOCUS MODE: Use the LEFT/RIGHT button to select ON/OFF the Focus mode. In Focus mode, the iris becomes fully open, electronic shutter controls the light level, and the TV out screen zooms into the center in order to make focusing easier. When in Focus Mode, the OSD menu is not displayed. - FACTORY RESET: Use the SET button to action start of reset. Clear all setting and initialize to factory setting. COMMUNICATION (Sub Manu) COMMUNICATION * CAMERA ID * BAUD RATE * COMM APPLY 0.2B.25 DISABLE OFF NO. 1 2.4K - CAMERA ID : Use the LEFT/RIGHT button to select the RS485 ID Address. - BAUD RATE : Use the LEFT/RIGHT button to select the baudrate setting for RS485 communication. - COMM APPLY : Apply all communication setting changed at once. Use the SET button to apply. EXIT This menu can be accessed when use the EXIT action in all menu pages. SAVE & EXIT SETUP EXIT WITHOUT SAVING - SAVE & EXIT SETUP: Save all current setting and Close OSD menu. These setting are loaded and applied automatically when the Camera is power on. - EXIT WITHOUT SAVING: Close OSD menu. Camera s current setting is not saved. Use the SET button to action. 31
Quick Setup Guide(HD CCTV CAMERA) OSD Menu Button. UP / 720p LEFT / NTSC RIGHT / PAL DOWN / 1080p - Video out Format Change (NTSC/PAL Selection) Default(Factory default setting) video out format is NTSC. Camera power on & Until push the SET button(while OSD menu is not displayed on video), Can select NTSC/PAL video format output on VIDEO port - Push the LEFT button to select NTSC format video out mode or Push the RIGHT button to select PAL format video out mode. *Warning : When HD-SDI out format is setted 1080P, NTSC/PAL video out is not supported. While OSD menu is not displayed on video, Can select 1080P/720P format output on HD-SDI port - Push the UP button in 3 seconds to select 720P format video out or Push the DOWN button in 3 seconds to select 1080p format video out. - OSD menu Display on Video Push the SET button. - Use the Focus mode Can be found in SYSTEM menu section in OSD menu. Use the LEFT/RIGHT button to select ON/OFF the Focus mode. Video output port - HDcctv 1.0 OUTPUT (BNC) : HD-SDI video out to HDcctv DVR or Other HDcctv Signal Equipment. - VIDEO (BNC) : NTSC or PAL video out to Hand-Held Test Equipment(TV Monitor). Focus Mode In the Focus mode, the Iris becomes fully open and the TV out screen zooms into the center in order to make focusing easier. When turn on the Focus mode, the OSD menu display in turned off automatically and when turn off the focus mode, the OSD menu display is back.