Adapter Kit - Remote QSI Electronics Installation Instructions

Adapter Kit Remote QSI Electronics Installation Instructions These installation instructions cover the adapter kit installation of the QSI1, QSI2 and QSI3 versions of communications electronics. The instructions are the same for QSI versions with or without a display. Check the contents of your kit using the list below as a reference. Make sure the power to your meter is disconnected. INSTRUCTIONS 1. Select the mounting location and mount the remote adapter using the (4) mounting ears provided. The holes in the ears will accommodate a 1/4 diameter bolt or screw. The remote can be mounted in any orientation. 2. Remove the (6) 816 x 3/4 screws attaching the kit cover plate to the adapter and separate. Do not damage the seal between the two components (see Figure 1). 3. To route external power and/or electronic cables to the QSI PC board screw connectors, prepare the cover plate by removing the mushroom plug from each strain relief you intend to use. The strain relief will accommodate cable sizes of 0.11 (0.28 cm) through 0.26 (0.66 cm) diameter. 4. Make sure the power is disconnected from external cables before beginning this step. Route external cables through the strain reliefs, and then tighten the dome nut securely around the cable to provide an environmental seal. 5. Connect cable wires to the QSI PC board screw connectors per the wiring diagram in these instructions. 6. Mount the cover plate on the adapter making sure the seal is seated properly between them. Replace the (6) previously removed screws to secure the cover plate to the adapter. Tighten screws. 03/2017 92089705 Rev

(6) SCREWS, #816 X 3/4 COVER PLATE Q09 DISPLAY (SHOWN) (OR) NO DISIPLAY MUSHROOM PLUGS (4) SEAL MOUNTS ADAPTER Figure 1 (1) Completely assembled QSI module (with or without a display). (1) Instruction sheet. KIT CONTENTS (1) QSI Owner s manual. (1) Q09 Owner s manual (if kit includes Q09 display). 2

TERMINAL CONNECTIONS CHART PT100Red PT100White Sensor #1 PT100Blue PT100Red PT100White Sensor #2 PT100Blue RS485 RS485 RS485 GND 5v RS485 Power 420mA GPI Sensor Output Figure 2 TEMP SENSOR PT100Red Sensor VCC Output PT100White High Side PT100Blue Return RS485 (Galvanically Isolated) RS485 () Positive Signal RS485 () Negative Signal RS485 GND Circuit Ground* PULSE INPUT 5VDC output to pow 5V er external sensor Digital Fre () quency, up to 3kHz () Digital Return 420mA (Galvanically Isolated) 4 to 20mA current () loop current in to transmitter 4 to 20mA current () loop current out of transmitter* *NOTE: It is not recommended to connect isolated ground connections together or to board common. Low level sine wave input Low level sine wave input GPI SENSOR Ribbon cable connection to GPI custom sensor designs PULSE OUTPUT (Galvanically Isolated) Output return () current* Output frequency output. This () is a current sinking open collector output.*** POWER INPUT 1236V AC or DC () A** 1236V AC or DC () B** **NOTE: Polarity of voltage for AC/ DC is not important. However an earth ground isolated power supply is required to prevent earth ground loop currents and ground fault conditions. ***NOTE: This output may require an external pull up resistor if interfacing equipment does not include one. 3

S QSI VERSION 1 PC BOARD RS485 BTU RTDs RS485 & B (Nonpolarized) Out Power In Figure 3 ISOLATED POWER SUPPLY 1236V AC/DC () () Power () Power () s: Temp Sensors, GPI Custom Sensor Outputs: RS485, Output QSI Version 1 Out () Out () Open Collector R 1 5V In () In () Unpowered Pickup Coil PT100 (Red) PT100 (White) PT100 (Blue) PT100 (Red) PT100 (White) PT100 (Blue) RS485 () RS485 () RS485 (GND) *R 2...=120Ω R 2 *Shield RS485 () RS485 () RS485 (GND) Figure 4 4

S In BTU RTDs & B (Nonpolarized) Out Power In Figure 5 ISOLATED POWER SUPPLY 1236V AC/DC () () Power () s: Temp Sensors, GPI Custom Sensor Outputs: Output QSI Version 2 Power () Unpowered Pickup Coil R 1 5V In () In () Out () Out () Open Collector PT100 (Red) PT100 (White) PT100 (Blue) PT100 (Red) PT100 (White) PT100 (Blue) Figure 6 5

ISOLATED S QSI VERSION 3 PC BOARD 420mA & B (Nonpolarized) 420mA Out Power In Figure 7 s: GPI Custom Sensor Outputs: 420mA, Outputs ISOLATED POWER SUPPLY 1236V AC/DC () () Power () QSI Version 3 Out () Out () Power () Unpowered Pickup Coil R 1 5V In () In () 420mA () Min. V = 8.5 Max. V = 36 420mA () Figure 8 6 without Builtin Power Supply 420mA Output with Separate Power Supply

S without Builtin Power Supply 420mA Output with Separate Power Supply ISOLATED POWER SUPPLY 1236V AC/DC () () Power () QSI Version 3 Power () 420mA () (Current) Loop () 420mA () (Current) (Current) Loop () Isolated Power Supply Figure 9 () () Figure 10 ISOLATED POWER SUPPLY 24V DC 24V DC recommended for use with both QSI & Conditioned Signal Output Module () () Power () Min. V = 8.5 Max. V = 36 Open Collector Signal Output Into QSI Versions 1, 2 or 3 Power () Red 9 to 35 volt DC Terminal Block Pull Up Resistor 1 2 3 4 Black Common Ground 5v Power White Open Collector Signal (FLOMEC Conditioned Signal Output Module wiring shown above. Diagram is excerpt from module owner s manual.) NOTE: Pull up resistor shown in FLOMEC Conditioned Signal Output Module wiring diagram above is not required for use with QSI Versions 1, 2, or 3. If resistor is already installed, there is no need to remove it. 7