More Precision wiresensor // Draw-wire displacement sensors
Low-cost draw-wire displacement sensors wiresensor MK30 analog - Robust plastic housing - Customized versions for OEM - Conductive plastic/wire/ hybrid potentiometer - Smallest design in its class Model MK30-P (Measuring range 50mm) 8 0.5 Ø8 Ø4.5 Ø3 mounting hole 3x Ø.7 3 pin mounting clip with screw M3 3.5 30 Ø5 3.5 4 3.5 3.5 30 3. 0. 4 5 Model MK30-P (Measuring range 50/50/500/750mm) Ø8 8 (WPS-500-MK30-P) (WPS-750-MK30-P) Ø4.5 Ø3 mounting hole 3x Ø.7 mounting clip with screw M3 3.5 3.5 45.5 3.5 3.5 30 30 Ø3 4.5 0. 4 5
7 Model WPS-50-MK30 WPS-50-MK30 WPS-50-MK30 WPS-500-MK30 WPS-750-MK30 Output P Measuring range 50mm 50mm 50mm 500mm 750mm conductive plastic pot. <0.5% FSO <0.5mm - - - - Linearity wire pot. P5 <0.5% FSO - - - <.5mm <.87mm hybrid pot. P5 <0.5% FSO - <0.375mm <0.5mm - - hybrid pot. P5 <0.% FSO - - <0.5mm <0.5mm <0.75mm conductive plastic pot. quasi infinite Resolution wire pot. - 0.mm 0.mm 0.5mm 0.mm hybrid pot. quasi infinite conductive plastic / wire / hybrid potentiometer Temperature range Material Wire mounting Sensor mounting Wire acceleration Wire retraction force (min) housing draw wire -0... +80 C plastic coated polyamid stainless steel (ø 0.3mm) eyelet mounting holes / mounting grooves appr. 5g appr. N Wire extension force (max) appr..5n Protection class IP 0 Electrical connection Weight FSO = Full Scale Output Specifications for analog outputs on page 5. soldering tag appr 45g rticle description WPS - 50 - MK30 - P5 Output option: potentiometer P50 (Linearity <0.5% FSO) potentiometer P5 (Linearity <0.5% FSO) potentiometer P0 (Linearity <0.% FSO) Model MK30 Measuring range in mm
8 Low-cost draw-wire displacement sensors wiresensor MK30 digital - Robust plastic housing - Customized versions for OEM - Smallest design in its class - Incremental encoder Model MK30 8 (WPS-500-MK-E) (WPS-750-MK30-E) ø8 ø4.5 ø3 0.5 mounting clip with screw M3 30 45.5 3.5 3.5 ø4 3.5 3.5 30 ø.7 mounting hole 40 0. 4 5
9 Model WPS-500-MK30 WPS-750-MK30 Output E/E830 E/E830 Measuring range 500mm 750mm Linearity E <0.05% FSO <0.5mm <0.375mm Resolution Sensor element 0 pulses/mm.7 pulses/mm 0.mm 0.5mm Incremental encoder Temperature range -0... +80 C Material Wire mounting Sensor mounting Wire acceleration Wire retraction force (min) housing draw wire plastic coated polyamid stainless steel (ø 0.3mm) eyelet mounting holes / mounting grooves appr. 5g appr. N Wire extension force (max) appr..5n Protection class Electrical connection Weight FSO = Full Scale Output Specifications for digital outputs on page 5. IP54 cable radial, m appr. 80g rticle description WPS - 500 - MK30 - E830 Output option: encoder E (5... 4 VDC) encoder E830 (8... 30 VDC) Model MK30 Measuring range in mm
50 ccessories and mounting wiresensor ccessories: pplication example with accessories WE-xxxx-M4 Wire extension with M4-wire connection, x=length WE-xxxx-Clip Wire extension with eyelet, x=length TR-WDS Pulley wheel, adjustable TR3-WDS Pulley wheel, fixed GK-WDS MH-WDS MH-WDS MT-0-WDS ttachment head for M4 Magnetic holder for wire mounting Magnetic holder for sensor mounting Mounting clamp for WDS-P0 MT-0-WDS mounting clips MH-WDS magnetic holder measuring range FC8 Female connector for WDS, 8-pin FC8/90 Female connector 90 for WDS PC 3/8-WDS Sensor cable, lenght 3m PS 00 (Power Supply 4 V /,5, Input 00-40 VC, output 4 VDC /.5, for snap in mounting on DIN 500 rail) WE-x-Clip wire extension WDS-MP0 Mounting plate for P0 sensors TR3-WDS pulley wheel, fix TR-WDS pulley wheel, adjustable, 85.5 78.5 0 40 x Ø4.5 x Ø5.3 Installation information: Wire attachment: The free return of the measurement wire is not per- Mounting plate WDS-MP0 missible and it is essential that this is avoided during installation. Wire exit angle: When mounting a draw-wire displacement sensor, a straight wire exit (±3 tolerance) must be taken into account. If this tolerance is exceeded, increased material wear on the wire and at the wire aperture must be expected. wire aperture 0 (±3 tolerance)
Output specifications analog 5 Output Plug M -S / -SR Integrated cable -C / -CR Open contacts Potentiometric output (P) Supply voltage max. 3VDC at kohm / Wmax 5 4 Resistance Temperature coefficient kohm ±0% (potentiometer) ±0.005% FSO/ C 3 7 8 sensor side = input + = ground 3 = signal white = input + brown = ground green = signal = input + = signal 3 = ground CCW 3 CW CLOCKWISE WIPER Voltage output (U) Supply voltage Current consumption Output voltage Load impedance Signal noise Temperature coefficient Electromagnetic compatibility (EMC) 4... 7VDC (non stabilised) max. 30m 0... 0VDC Option 0... 5 / ±5V >5kOhm 0.5mV eff ±0.005% FSO/ C EN 000--4 EN 000-- 5 4 3 8 7 sensor side djustment ranges (if supported by the model) Zero ±0% FSO Sensitivity ±0% = supply = ground 3 = signal 4 = ground white = supply brown = ground green = signal yellow = ground Current Output (I) Supply voltage Current consumption Output current Load Signal noise Temperature coefficient Electromagnetic compatibility (EMC) 4... 7VDC (non stabilised) max. 35m 4... 0m <00Ohm <, µ eff ±0.0% FSO/ C EN 000--4 EN 000-- 5 4 3 8 7 sensor side djustment range (if supported by the model) Zero ±8% FSO = supply Sensitivity ±5% = ground white = supply brown = ground
5 Output specifications SSI wiresensor Contact description U Encoder power supply connection Encoder ground connection. GND The voltage drawn to GND is U. Positive SSI pulse input. Pulse + forms a current loop with 3 Pulses + pulse -. current of approx. 7 m in direction of pulse + input generates a logical in positive logic. Positive, serial data output of the differential line 4 Data + driver. High level at the output corresponds to logical in positive logic. 5 ZERO Data - 7 Pulses - 8 / 0 DTVLID DTVLID MT 9 UP/DOWN / Not in use Zero setting input for setting a zero point at any desired point within the entire resolution. The zeroing process is triggered by a High pulse (pulse duration 00 ms) and must take place after the rotating direction selection (UP/ DOWN). For maximum interference immunity, the input must be connected to GND after zeroing. Negative, serial data output of the differential line driver. High level at the output corresponds to logical 0 in positive logic. Negative SSI pulse input. Pulse - forms a current loop with pulse +. current of approx. 7 m in direction of pulse - input generates a logical 0 in positive logic. Diagnosis outputs DV and DV MT Jumps in data word, e.g. due to defective LED or photoreceiver, are displayed via the DV output. In addition, the power supply of the multiturn sensor unit is monitored and the DV MT output is set when a specified voltage level is dropped below. oth outputs are Low-active, i.e. are switched through to GND in the case of an error. UP/DOWN counting direction input. When not connected, this input is on High. UP/ DOWN-High means increasing output data with a clockwise shaft rotating direction when looking at the flange. UP/ DOWN-Low means increasing values with a counter-clockwise shaft rotating direction when looking at the flange. Pin assignment Pin Cable color ssignment brown U black GND 3 blue Pulses + 4 beige Data + 5 green ZERO yellow Data - 7 violet Pulses - 8 brown/yellow DTVLID 9 pink UP/ DOWN 0 black/yellow DTVLID MT - - - - 7 Inputs 8 9 5 0 4 3 Please use leads twisted in pairs for extension cables. Control signals UP/DOWN and Zero Level High Level Low Connection: > 0.7 U < 0.3 U UP/DOWN input with 0kohms to U, zeroing input with 0kohms to GND. SSI pulse Optocoupler inputs for electrical isolation Outputs SSI data RS485 driver Diagnostic outputs Push-pull outputs are short-circuit-proof Level High > U -3.5V (with I = -0m) Level Low 0.5V (with I = 0m)
Output specifications CNopen 53 CNopen features Setting CNopen baud rate us protocol CNopen Device profile CNopen - Ci DSP 40, V 3.0 aud rate Setting Dip Switch 3 CNopen Features Device Class, CN.0 0kit/s OFF OFF OFF Operating modes (with SDO progr.) Polling Mode (asynch, via SDO) Cyclic Mode (asynch-cyclic) The encoder cyclically sends the current process actual value without a request by a master. The cycle time can be parameterized for values between and 5535 ms. Synch Mode (synch-cyclic) The encoder sends the current actual process value after receiving a synch telegram sent by a master. The synch counter in the encoder can be parameterized so that the position value is not sent until after a defined number of synch telegrams. cyclic Mode (synch-acyclic) 0kit/s OFF OFF ON 50kit/s OFF ON OFF 5kit/s OFF ON ON 50kit/s ON OFF OFF 500kit/s ON OFF ON 800kit/s ON ON OFF Mit/s ON ON ON Preset value Rotating direction Scaling With the Preset parameter the encoder can be set to a desired actual process value that corresponds to the defined axis position of the system. The offset value between the encoder zero point and the mechanical zero point of the system is saved in the encoder. With the operating parameter the rotating direction in which the output code is to increase or decrease can be parameterized. Scaling The steps per revolution and the total revolution can be parameterized. The steps per revolution and the total revolution can be parameterized. Contact description CNopen CN_L CN us Signal (dominant Low) CN_H CN us Signal (dominant High) U Supply voltage 0...30VDC GND Ground contact for U (Terminals with the same designation are internally interconnected) Diagnose The encoder supports the following error messages: - Position and parameter error - Lithium cell voltage at lower limit (Multiturn) Default setting 50kbit/s, node number Settings of user address for CNopen ddress can be set with rotary switch. Example: User address 3 ON CN_L CN_H U GND CN_L CN_H U GND ON 3 Setting of terminating Resistor for CNopen ON ON = Last user OFF = User X
54 Output specifications Profibus wiresensor Profibus-DP features us protocol Profibus-DP Profibus features Device Class and ON Data exch. functions Input: Position value dditional parameterized speed signal (readout of the current rotary speed) Output: Preset value Preset value Parameter functions With the Preset parameter the encoder can be set to a desired actual value that corresponds to the defined axis position of the system. Rotating direction: With the operating parameter the rotating direction for which the output code is to increase or decrease can be parameterized. U GND U GND Settings of terminating resistors for Profibus-DP ON Diagnose Default setting User address 00 The encoder supports the following error messages: - Position error - Lithium cell voltage at lower limit (Multiturn) ON = last user OFF = user X Settings of user address for Profibus-DP Settings of user address for Profibus-DP Contact description Profibus-DP Negative serial data line Positive serial data line U Supply voltage 0...30VDC GND Ground contact for U (Terminals with the same designation are internally interconnected)
Output specifications Incremental encoder 55 Signal output 0 0 Pin assignment TTL, HTL Pin Cable color ssignment Pin pink inv. Pin blue U Sense Pin 3 red N (zero impulse) Pin 4 black N inv. (zero impulse inv.) Pin 5 brown Pin green inv. Pin 7 - - Pin 8 grey Pin 9 - - Pin 0 white/green GND Pin white GND Sense Pin brown/green U Output TTL Linedriver (5 VDC) Level High.5V (with I = -0m) Pegel Low 0.5V (with I = 0m) Load High 0m 7 8 9 0 5 4 3 Pin and Pin are internally connected as well as Pin and 0. For cable length >0m twisted pair wires are required. Output,,,, 0 Output TTL0 NPN (5 VDC ±5%) Level High U -0.V Level Low 0,55-0.75V Load High.85m Output,, 0 Output TTL0 Linedriver (5 VDC ±5 %) Level High.0V (with I= -40m) Level Low 0.5V (with I= 40m) Load High 40m Output,,,, 0 Output HTL Push-pull (0... 30 VDC) Level High U -3V (with I = -0m) Level Low.5V (with I = 0m) Load High 40m Output,,,, 0 Output E Push-pull ((5 VDC) Level High U -.5V Level Low 0.5V Load High 50m Output,, 0 Output E830 Push-pull ((8... 30 VDC) Level High U -3V Level Low.5V Load High 50m Output,, 0 Connection assignment E, E830 Cable color ssignment white 0V brown +U green - yellow - grey 0 Connection assignment TTL0 Cable color ssignment brown 0V grey +U white green yellow 0 Connection assignment TTL0 Cable color ssignment red +U black 0V brown black orange black yellow 0 black n.c.
High performance sensors made by Micro-Epsilon Sensors and systems for displacement and position Sensors and measurement devices for non-contact temperature measurement D/3D profile sensors (laser scanner) Optical micrometers, fibre optic sensors and fibre optics Color recognition sensors, LED analyzers and color inline spectrometer Measurement and inspection systems Modifications reserved / Y97-03GKE MICRO-EPSILON US 80 rownleigh Dr. Raleigh, NC 77 / US Phone +/99/787-9707 Fax +/99/787-970 me-usa@micro-epsilon.com www.micro-epsilon.com