www.edison-opto.com Solid-State Lighting Series PLCC SMT Down Light DATASHEET Features High Brightness SMD LED Light source Ecological Friendly Fully Integral Design Energy Efficient
General Information... 1 Product Dimensions... 2 Product Information... 3 Technical Data... 3 Light Pattern... 4 Assembly Instructions and Recommended Driver Specification... 5 Applications... 6 Product Safety... 7 Package Information... 8 Revision History... 8 About Edison Opto... 9
General Information Introduction Ultra-light PLCC SMT Down Light is designed with high quality PLCC Emitters and integrated with thermal, electrical, mechanical and optical aspect from Edison Opto. The design is to simplify the structure with a small amount of components to achieve the target. Besides, with the high quality lighting solution systems, the product provides a widely use of space from residential to commercial illuminated applications. 1
Product Dimensions Tolerance: ±2.5 mm 45 mm Ø140 mm Ø105 mm 4" PLCC SMT Down Light Tolerance: ±2.5 mm 45 mm Ø185 mm Ø150 mm 6" PLCC SMT Down Light Tolerance: ±2.5 mm 45 mm Ø240 mm Ø200 mm 8" PLCC SMT Down Light 2
PLCC SMT Down Light DATASHEET www.edison-opto.com Product Information Product Type 12W 4" SMT Down Light 26W 6" SMT Down Light 32W 8 SMT Down Light Product Order Code 7-DL04-06 7-DL06-10 7-DL08-10 WATT COLOR ANGLE DRIVER COVER Code Type Code Type Code Type Code Type Code Type 12 12W 30 3,000 K F >70 0 No Driver W0 White 26 26W 40 4,000 K A 100-240V 32 32W 57 5,700 K C 220V DIM Note: Available selection of Watt, color and driver. Technical Data Power Consumption Parameter Rating / Value Units 12 (4") 26 (6") 32 (8") Color Temperature 5,700/ 4,000/ 3,000 K CRI >80 -- Operating Temperature -20 ~ +40 C Storage Temperature -40 ~ +60 C W Notes : 1. Power consumption has 10% tolerance. 2. Color rendering index (CRI) is measured with accuracy in minimum. 3. The operating temperature* is based on the ambient temperature to the heatsink in 5 cm distance. 3
Technical Data Power Consumption (W) Size Beam Angle Color Typ. Lux @1m (lx) Typ. Flux (lm) 5700K 490 1100 12W 4 inch 4000K 470 1050 3000K 450 1000 5700K 1050 2300 26W 6 inch Flood 4000K 1000 2200 3000K 950 2100 5700K 1530 3400 32W 8 inch 4000K 1470 3300 3000K 1400 3200 Notes: 1. LED is a dynamic and constantly evolving technology. The final lux output of your PLCC COB Down Light may vary. 2. Angle has ±5 tolerance. 3. Flux and Lumen are measured under thermal balance condition @ Ta=25oC. Light Pattern 105 Flood 105 90 90 75 0.2 75 60 0.4 60 45 0.6 45 0.8 30 15 1.0 0 1 5 30 4
Assembly Instructions and Recommended Driver Specification Input Voltage Output Voltage Operating Current (Constant) Rated Power AC 100~240V DC16~18V (4") DC36~38V (6") 700mA >15W (4") >30W (6") DC31~33V (8 ) 1050mA >35W (8") Assembly Instructions 1. Connect the PLCC SMT Down Light to the DC driver shown as step 1 2. Plug the driver to AC outlet shown as step 2 Caution Never plug the driver to AC outlet before the PLCC SMT Down Light is properly connected, otherwise it may damage the LEDs permanently. 5
Applications Retail stores Residential Restaurants Commercial spaces Hotel lobby Office spaces, meeting rooms 6
Product Safety WARNING Risk of Electrical Shock, Injury, and damage Disconnect or turn off power before servicing or installing luminaire. Do not hot swap! LED heat sink module must not to be disconnected with line power on failure to do so may damage product. Installation of LED product (with driver) needs to be made with regard to all applicable electrical and safety standards. Only qualified personnel should be allowed to perform installations. Verify that supply voltage is correct by comparing it with the luminaire and driver. All wiring connections should be capped with UL approved recognized wire connectors. The luminaire shall, under no circumstance, be covered with thermal insulation matting or similar material, and pay attention not to exceed the maximum operation temperature of LED module. If the IP rating of the fixture should be higher than IP20, the design of the housing should be according to the IP standards in the application. The LED module itself and all its components must not be mechanically stressed. Assembly must not damage or destroy conducting paths on the circuit board. Be aware of, the luminaire is intended for indoor application and keep away from any chemicals CAUTION Avoid direct eye exposure to the light source while it is on. Wear safety glasses and gloves during installation and servicing. Allow lamp/fixture to cool before handling. Do NOT touch enclosure or light source. Follow all manufacturers warnings, recommendations and restrictions for : driver type, burning position, mounting location/methods, and replacement. 7
Package Information 1pc / Pack 21 Packs / Carton (4") 12 Packs / Carton (6") 16 Packs / Carton (8") 4" PLCC COB Down Light 1. Pack Dimensions : 165mm(length)*165mm(width)*50mm(height) 2. Carton Dimensions : 530mm(length)*430mm(width)*195mm(height) 3. Figures not shown to scale. 6" PLCC COB Down Light 1. Pack Dimensions : 210mm(length)*210mm(width)*50mm(height) 2. Carton Dimensions : 530mm(length)*430mm(width)*195mm(height) 3. Figures not shown to scale. 8" PLCC COB Down Light 1. Pack Dimensions : 250mm(length)*250mm(width)*60mm(height) 2. Carton Dimensions : 640mm(length)*475mm(width)*260mm(height) 3. Figures not shown to scale. Revision History Versions Description Release Date 1 Establish order code information 2014/01/15 2 1. Add 8" PLCC SMT Down Light 2. Update CCT 2014/05/26 3 Revise Power consumption 2014/06/06 4 1. Establish a New version 2. Revise Application&Photo of front page 2014/08/15 8
About Edison Opto Edison Opto is a leading manufacturer of high power LED and a solution provider experienced in LDMS. LDMS is an integrated program derived from the four essential technologies in LED lighting applications- Thermal Management, Electrical Scheme, Mechanical Refinement, Optical Optimization, to provide customer with various LED components and modules. More Information about the company and our products can be found at www.edison-opto.com. Copyright 2014 Edison Opto. All rights reserved. No part of publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photo copy, recording or any other information storage and retrieval system, without prior permission in writing from the publisher. The information in this publication are subject to change without notice. For general assistance please contact: service@edison-opto.com.tw For technical assistance please contact: LED.Detective@edison-opto.com.tw 9