Contour Measuring Systems CONTRACER CV-3200/4500 Series

Form Measurement Contour Measuring Systems CONTRACER CV-3200/4500 Series Bulletin No. 2067 igh-accuracy contour measuring machine with exciting new features

CONTRACER CV-4500 Series Continuous top-bottom measurement function for easy measurement of upper and lower surfaces Upper and lower surfaces can be measured continuously by using Mitutoyo s double-sided conical stylus. This continuous measurement data can be used to facilitate analysis of features that were difficult to measure before, such as the effective diameter of an internal screw-thread. Lower direction measurement (Bottom surface) Top and bottom measurement switched by software Upper direction measurement (Top surface) Variable measuring force function The measuring force can be varied in 5 steps by using the software provided (FORMTRACEPAK), eliminating the need to adjust the measuring force by switching weights or through positional adjustment. The CV-4500 Series can also maintain the specified measuring force even when tilted. Measuring force X-axis inclination Measuring direction Effective diameter Continuous top-bottom measurement allows hassle-free one-step calibration (Patent pending in Japan) The one-step calibration kit supplied with the CV-4500 Series has been upgraded to enable easy calibration of the double-ended conical stylus featuring a contact on both the top and the bottom. Precise work such as calibrating the Z1-axis gain, symmetry, and stylus radius can now be carried out in a single operation. Calibration kit for CV-4500series Plain-section diameter Ball Gauge blocks Pin gauge Measuring force maintained Best-in-class displacement accuracy The CV-4500 Series features a built-in precision arc scale on the Z1 axis (detector) that allows the arc trajectory of the stylus tip to be read directly, minimizing the detector mechanism error and enabling precision, high-resolution measurement. On the X axis (driver) is a linear scale, allowing high-accuracy full-stroke measurement. Accuracy Z1 axis (detector unit): ± (0.8 + 2 /100) μm = Measurement height from the horizontal position (mm) X axis (drive unit): ±(0.8+0.01L) µm * 1 L = drive length (mm) Resolution Z1 axis (detector unit) : 0.02µm X axis (drive unit) : 0.05µm *1 These specifications apply to the CV-4500S4/4/W4. For specifications of other products in the series, see Specifications on page 14. Fast traverse improves measurement efficiency X axis (drive unit) : 80mm/s (MAX) Z2 axis (column) : 30mm/s (MAX) The total measurement time can be shortened by speeding up the traverse movements. Z2 axis (column) X axis (drive unit) 2

New top-bottom continuous measurement and variable measuring force enable efficient, highly accurate measurement of a wide range of objects. CV-4500 Detector with new arm design Expands measurement range while reducing workpiece interference Mitutoyo s newly designed detector arm lowers workpiece interference while expanding the measurement range in the Z1 axis (detector). When using the SP-71 one-sided cut stylus CV-4100 CV-4500 (Conventional product) 50 mm 10 mm 60 mm 19 mm Detector measurement range expanded by 10 mm One-touch arm attachment (Patent pending in Japan) The arm mount uses a magnetic joint for quick and easy arm replacement. The mount also includes a safety mechanism. CV-4100 (Conventional product) CV-4500 Excellent operability Remote-control unit enables safe, easy & fast measurement The remote-control unit lets you move quickly from positioning to measurement. The unit also features an emergency stop switch and speed control knob for added safety while the machine is moving at high speeds. Emergency stop switch Drive speed control knob New Remote Control Box Remarkable Ease of Operation Incorporation of an ABS scale in the Z2 axis eliminates the need for wearisome origin point re-setting conventionally required for every step of repeated measurements over stepped or multiple sections. Screw fixing Removable unit (arm) Magnetic joint Removable unit (detector) All detector and drive unit cables are housed inside the main unit to eliminate any risk of abrasion and guarantee trouble free, highspeed operation. Simple positioning by fine feed mechanisms Inclination unit Small holes and inclined planes can be efficiently measured using the inclined X-axis drive unit and fine-feed handles on the X and Z2 axes. Z2-axis fine-feed handle X-axis fine-feed handle X-axis inclination handle Auto stop feature assures safety even during high-speed movement The detector includes a safety mechanism (auto stop upon collision) to assure measurement safety even during high-speed movement. If the arm is removed or shifts during measurement, the safety mechanism is triggered and stops the machine. Direction of collision that may cause the safety device to be triggered Simplified CNC Function With the support for a wide range of optional peripherals designed for use with the CNC Form Measuring Unit enables simplified CNC measurement. 1-axis Rotary unit: Automatic circular-form measurement 2-axis Rotary unit: Automatic multiple-section continuous measurement Removable unit 3

CONTRACER CV-3200 Series Detector with new arm design Expands measurement range while reducing workpiece interference Mitutoyo s newly designed detector arm lowers workpiece interference while expanding the measurement range in the Z1 axis (detector). When using the SP-71 one-sided cut stylus CV-3100 CV-3200 (Conventional product) 50 mm 10 mm 60 mm 19 mm Detector measurement range expanded by 10 mm One-touch arm attachment The arm mount uses a magnetic joint for quick and easy arm replacement. The mount also includes a safety mechanism. CV-3100 (Conventional product) CV-3200 (Patent pending in Japan) assle-free one-step calibration The CV-3200 Series provides a dedicated calibration gage that lets you carry out precise work such as calibrating the Z1-axis gain, symmetry, and stylus radius in a single operation. Calibration of upward measurement is also possible by using Mitutoyo s optional calibration stage. Calibration kit for CV-3200 series Gauge blocks Ball Pin gauge Screw fixing Removable unit (arm) Magnetic joint Removable unit (detector) All detector and drive unit cables are housed inside the main unit to eliminate any risk of abrasion and guarantee trouble free, highspeed operation. Auto stop feature assures safety even during high-speed movement The detector includes a safety mechanism (auto stop upon collision) to assure measurement safety even during high-speed movement. If the arm is removed or shifts during measurement, the safety mechanism is triggered and stops the machine. Direction of collision that may cause the safety device to be triggered Best-in-class displacement accuracy The CV-3200 Series features a built-in precision arc scale on the Z1 axis (detector) that allows the arc trajectory of the stylus tip to be read directly, minimizing the detector mechanism error and enabling precision, high-resolution measurement. On the X axis (driver) is a linear scale, allowing high-accuracy full-stroke measurement. Accuracy Z1 axis (detector unit): ± (1.6 + 2 /100) μm = Measurement height from the horizontal position (mm) X axis (drive unit): ±(0.8+0.01L) µm* 1 L = drive length (mm) Resolution Z1 axis (detector unit): 0.04µm X axis (drive unit): 0.05µm *1 These specifications apply to the CV-3200S4/4/W4. For specifications of other products in the series, see Specifications on page 14. Removable unit 4

Best-in-class accuracy, high-speed movement, and new detector arm design enable hassle-free, highly accurate measurement. CV-3200 Excellent operability Remote-control unit enables safe, easy & fast measurement The remote-control unit lets you move quickly from positioning to measurement. The unit also features an emergency stop switch and speed control knob for added safety while the machine is moving at high speeds. Emergency stop switch Drive speed control knob New Remote Control Box Fast movement improves measurement efficiency X axis (drive unit) : 80mm/s (MAX) Z2 axis (column) : 30mm/s (MAX) The total measurement time can be shortened by speeding up the movement. Z2 axis (column) X axis (drive unit) Remarkable Ease of Operation Incorporation of an ABS scale in the Z2 axis eliminates the need for wearisome origin point re-setting conventionally required for every step of repeated measurements over stepped or multiple sections. Simplified CNC Function With the support for a wide range of optional peripherals designed for use with the CNC Form Measuring Unit enables simplified CNC measurement. 1-axis Rotary unit: Automatic circular-form measurement Simple positioning by fine feed mechanisms Small holes and inclined planes can be efficiently measured using the inclined X-axis drive unit and fine-feed handles on the X and Z2 axes. Inclination unit Z2-axis fine-feed handle X-axis fine-feed handle 2-axis Rotary unit: Automatic multiple-section continuous measurement X-axis inclination handle 5

Contour Analysis Software: FORMTRACEPAK FORMTRACEPAK functions offer total support for measurement system control, surface roughness analysis, contour analysis, contour tolerancing, and inspection report creation. Measurement control To make only a single measurement, you can create a part program in the single mode. To measure multiple workpieces of an identical shape, you can use the teaching mode. FORMTRACEPAK supports the new top-bottom continuous measurement and variable measuring force functions of the CV-4500 Series (see page 2 for details), providing an even higher level of usability. Since you can embed the entire flow, from making measurement to printing a report, into a part program, you can efficiently make measurements, analyze data, and output a report. A function is also provided that enables you to insert comments accompanied with photographs at desired timings, enabling you to embed the roles described in a measurement procedure document that specifies important points such as work settings. To make immediate measurements, you can use the pull-down menu to easily select and call up the desired operating procedure. Multiple language support (15 languages) You can switch the language* to be used in the measurement, analysis, and layout windows. After measurements have been made, you can switch to another language and create a report in that language. This function can be used worldwide. * Supported languages: Japanese, English, German, French, Italian, Spanish, Polish, ungarian, Swedish, Czech, Simplified Chinese, Traditional Chinese, Korean, Turkish, Portuguese. Online help function* Online help that can be viewed any time is incorporated into the software. In addition to index and keyword searches, a status saving help button, which displays menus and Windows help with a click of the mouse, is provided. Button-editing function You can hide buttons that are not used frequently. For example, you can choose to display only those buttons that are used frequently and increase the size of the displayed graphics window, thereby customizing the window to suit your needs. * Online help function supports only Japanese and English. Simple statistical commands You can perform statistical calculations of roughness parameters and contour analysis results without using a separate program such as Excel. 6

Contour analysis function A wide variety of commands, which form the basic elements for analysis, are provided, including those for points (10 kinds), lines (6 kinds), and circles (6 kinds). A rich set of commands that combine these elements to calculate angles, pitches, and distances, a contour tolerancing function, and a design value generation function are also provided as standard features. These functions, combined with the function that allows you to customize the calculation command buttons by hiding less frequently used commands, let you tailor the window according to the user environment. Circle and line automatic determination function Using the circle/line auto-fitting command, you can automatically calculate all circles and lines contained in the data without having to click the command button each time. Removal of abnormal points function Irregular defects in the data are filtered out from the calculation. This function is effective when specifying the calculation range for locations at which the boundary between circle and line is difficult to determine. Text output of the calculation result and graphics data You can output the calculation result as text (in csv or txt format), output graphics data obtained from measurements as point-string data to a text file or CAD file (in the DXF or IGES format), or copy the data to the clipboard. Combined with commercial document or statistical processing software, this feature can be used to share data with computers that do not have dedicated analysis software installed or execute CAD-based reverse engineering. Contour Analysis Simple pitch calculation function You can efficiently analyze the pitch between identical shapes, such as a screw pitch or the distance between circles (centerto-center pitch), by simply specifying the desired range using mouse operations. Example of range specification for screw thread pitch with rectangular tool. Contour-tolerancing function as a standard feature The best-fit processing function that moves the coordinate values of the design data and measurement data to the optimum positions is provided as a standard feature. Since the tolerancing results can be visually displayed as graphics, displayed as tolerance values and tolerance expansions in each coordinate, or output as a text file, they can be utilized as feedback data for machining systems. Example of contour-tolerancing result Example of contour tolerancing results output as numeric values 7

Contour Analysis Software: FORMTRACEPAK Contour Analysis Design value generation function You can generate design data from CAD data (DXF or IGES file) or text data. Furthermore, since you can also convert measurement data into design data, you can save parts data prior to use (testing) as design data and effectively utilize it for checking the wear following use (testing). Data combination function You can combine partial data collected separately from a workpiece (made necessary due to shape characteristics) into a single graphic for convenient analysis. Data 1 Data 2 Calculation command repetition setting When identical shapes have the same pitch, you can analyze all of the shapes in a batch by specifying a single analysis location and the pitch. Data combine Best-fit processing function for measurement point strings This function tries to fit the measurement points to the stored reference data on the same coordinate system. It can eliminate the effects of a shift that may occur when setting the workpiece during automatic analysis. Data superimposition command You can superimpose two sets of data by detecting their characteristic points. Use the mouse to drag and move the measurement point strings to the desired positions to be superimposed. 8

Integrated layout You can use simple operations to lay out graphics obtained from measurements as well as measurement results for surface roughness, contour, and roundness on a single page. Furthermore, since the program now allows you to specify a saved file and paste it, you can easily paste results from multiple files. Note: the optional ROUNDPAK roundness/cylindricity analysis program is required. (Ver. 7 or higher) Element information bar This bar displays the attribute values of the pasted items, allowing you to easily check the contents of the pasted measurement data files. System layout printing By simply selecting the items to be output, you can automatically lay out the page to be printed. Use this feature when you wish to simplify the printing task. Element insertion bar Using the mouse to drag and drop the analysis content displayed in the element insertion bar, you can paste it into the layout. From the contour analysis result, you can also select the analysis result for a circle or line alone and paste it in position. Saving the result as a web page Since you can save the result in html or mhtml format, which can be displayed using Internet Explorer or Microsoft Word, you can check the result even on a PC on which no layout-editing program is installed. Report creation function You can freely assemble measurement results/conditions/graphics as well as comments/circles/lines/arrows, and print them out in a measurement result report. Furthermore, since you can paste bitmap files, you can also add a workpiece image or company logo to the layout. You can also save the created layout and use it again later for similar measurements. 9

Optional Accessories for Automatic Measurement Y-axis table: 178-097 Enables efficient, automatic measurement of multiple aligned workpieces and multiple points on a single measurement surface. Travel range Resolution Positioning accuracy Drive speed Maximum load Mass 200mm 0.05μm ±3μm Max 80mm/s 50kg 28kg Rotary Table 1-axis table: 12AAD975* For efficient measurement in the axial/transverse directions. When measuring a cylindrical workpiece, automatic alignment can be performed in combination with the Y-axis table. * 1-axis mounting plate (12AAE630) is required when directly installing on the base of the CV-3200/4500 series. Displacement 360 Resolution 0.004 Maximum load 12kg Rotational speed Max 10 /s Mass 7kg Rotary Table 2-axis unit: 178-078* You can measure multiple points on a cylindrical workiece and automate front/rear-side measurement. * 2 -axis mounting plate (12AAE718) is required when directly installing on the base of the CV-3200/4500 series. Displacement 360 Resolution 0.0072 Maximum load (loading moment) 4kg (343 N cm or less) Rotational speed Max 18 /s Mass 5kg Centering chuck (ring operated): 211-032 Micro-chuck: 211-031 This chuck is useful when measuring small workpieces. You can easily clamp them with its knurled ring. Inner latch OD: ø1-6mm Retention Inner latch I D: ø16 - ø69mm range Outer latch OD: ø25 - ø79mm Dimensions ø118 41mm Mass 1.2kg This chuck is suitable for clamping extra-small diameter workpieces (ø1 mm or less), which cannot be retained with the centering chuck. Retention range Dimensions Mass OD: ø0.1 - ø1.5mm ø118 x48.5mm 0.6kg 10

Optional Accessories 3-axis Adjustment Table: 178-047 This table helps make the adjustments required when measuring cylindrical surfaces. The corrections for the pitch angle and the swivel angle are determined from a preliminary measurement and the Digimatic micrometers are adjusted accordingly. A flat-surfaced workpiece can also be leveled with this table. By using Mitutoyo s 3-axis adjustment table, the workpiece can be aligned and leveled easily, simply by following the FORMTRACEPAK guidance. No experience or special expertise is required. Guidance display when using 3-axis adjustment table Aligned End point Path traced by stylus Not Aligned End point Path traced by stylus Start point Start point Recorded profiles Table and fixture systems Leveling table 178-043-1 (mm), 178-053-1 (inch) Digital Leveling table 178-042-1 (mm), 178-052-1 (inch) Leveling table 178-016 Leveling table (for D.A.T.) 178-058 Calibration stand *1 12AAM100 Calibration stand *2 12AAG175 Calibration stand *3 12AAM309 V-block 998291 Precision vise 178-019 Cross-travel table 218-001 (mm), 218-011 (inch) Cross-travel table 218-041 (mm), 218-051 (inch) Rotary vise 218-003 Center support 172-142 Center support riser 172-143 Swivel center support 172-197 older with clamp 176-107 *1 Required for calibrating upward measurement of CV-3200 series. *2 Required for calibrating in bulk by mounting straight arm/small-hole stylus arm without using cross-travel table and Y-axis table. *3 Required for calibrating in bulk by mounting straight arm/eccentric arm/small-hole stylus arm without using cross-travel table and Y-axis table. V-block with clamp 172-234, 172-378 11

Optional Accessories Vibration isolators Desk types Desk type* 1 No.12AAK110 Monitor arm* 2 No.12AAK120 Side table* 3 No.12AAL019 Monitor arm Desk Side table Desk Example combination: with side table but no monitor arm (tester and PC not included) *1 For models with a product code that ends in S4, S8, 4, or 8. Please contact us directly if you require units for models with a product code that ends in W4 or W8 (large base models). *2 Used together with vibration isolator (No.12AAK110). *3 User to provide a printer rack. Desktop types Example combination: with monitor arm but no side table*3 (tester and PC not included) Manually charged pneumatic type* 4 No.178-023 Automatically charged pneumatic type* 4 No.178-025 Stand for Desktop type External size (W D ): 640 470 660mm Mass: 25kg No.178-024 *4 For models with a product code that ends in S4, S8, 4, or 8. Please contact us directly if you require units for models with a product code that ends in W4 or W8 (large base models). Arms Description Arm No. Parts No. Applicable stylus No. Straight arm AB-31* 5 12AAM101 SP-5S, 6S, 7S, 8S, 9S, SPW* 6-56,66,76 Eccentric arm AB-32 12AAM102 SP-5S, 6S, 7S, 8S, 9S, SPW* 6-56,66,76 Small-hole arm AB-33 12AAM103 SP-41, 42, 43 *5 Standard accessory *6 Stylus for CV-4500 series Straight arm AB-31 Eccentric arm AB-32 Small-hole arm AB-33 *7 One-sided cut stylus SP-71(standard accessory) mounting ø8 57.5 20 ø8 57.5 20 ø8 57.5 20 218* 7 218* 7 218* 7 40 12

Styli Stylus name Stylus No. Parts No. Application arm No. (mm) SPW-56 12AAM095* Double-sided 2 AB-31, AB-32 20 conical stylus* 1 SPW-66 12AAM096 AB-31, AB-32 32 SPW-76 12AAM097 AB-31, AB-32 48 SP-51 354882 AB-31, AB-32 6 SP-61 354883 AB-31, AB-32 12 One-sided cut SP-71 354884 * stylus 2 * 3 AB-31, AB-32 20 SP-81 354885 AB-31, AB-32 30 SP-91 354886 AB-31, AB-32 42 Intersecting cut stylus Cone stylus Tip angle 30 Sapphire tipped Cone stylus Tip angle 30 Cone stylus Tip angle 20 Cone stylus Tip angle 50 Diamond tipped Knife edge stylus Ball stylus SP-52 354887 AB-31, AB-32 6 SP-62 354888 AB-31, AB-32 12 SP-72 354889 AB-31, AB-32 20 SP-82 354890 AB-31, AB-32 30 SP-92 354891 AB-31, AB-32 42 SP-53 354892 AB-31, AB-32 6 SP-63 354893 AB-31, AB-32 12 SP-73 354894 AB-31, AB-32 20 SP-83 354895 AB-31, AB-32 30 SP-93 354896 AB-31, AB-32 42 SP-56 12AAA566 AB-31, AB-32 6 SP-66 12AAA567 AB-31, AB-32 12 SP-76 12AAA568 AB-31, AB-32 20 SP-86 12AAA569 AB-31, AB-32 30 SP-96 12AAA570 AB-31, AB-32 42 SP-57 12AAE865 AB-31, AB-32 6 SP-67 12AAE866 AB-31, AB-32 12 SP-77 12AAE867 AB-31, AB-32 20 SP-87 12AAE868 AB-31, AB-32 30 SP-97 12AAE869 AB-31, AB-32 42 SP-79 355129 AB-31, AB-32 20 SP-54 354897 AB-31, AB-32 6 SP-64 354898 AB-31, AB-32 12 SP-74 354899 AB-31, AB-32 20 SP-84 354900 AB-31, AB-32 30 SP-94 354901 AB-31, AB-32 42 SP-55 354902 AB-31, AB-32 6 SP-65 354903 AB-31, AB-32 12 SP-75 354904 AB-31, AB-32 20 SP-85 354905 AB-31, AB-32 30 SP-95 354906 AB-31, AB-32 42 Small hole stylus* 4 SP-42 12AAM105 AB-33 4 SP-41 12AAM104 AB-33 2 SP-43 12AAM106 AB-33 6.5 *1 Stylus for CV-4500 series *2 Standard accessory of CV-4500 series *3 Standard accessory of CV-3200 series *4 Styli SP-21, 22, and 23 for CV-3100/4100 series are not available. Double-sided conical stylus One-sided cut stylus Tip angle: 12º Intersecting cut stylus Arm stylus (comprising an arm and stylus) Arm stylus name Stylus No. Parts No. (mm) SPW-31 12AAM108 2.4 Double-sided small hole arm stylus SPW-32 12AAM109 5 SPW-33 12AAM110 9 *5 Arm Stylus for CV-4500 series Tip angle: 30º Tip angle: 20º Cone stylus Tip angle: 30º (SP-79: 50º) Sapphire, (SP-79:Diamond tipped) Cone stylus Knife edge stylus Ball stylus Tip angle: 20º Tip angle: 20º Edge width: 3mm Ball dia: 1mm Small hole stylus SP-41 0.4 1 ø1.6 ø4.8 55 Small hole stylus SP-42 ø5 55 Small hole stylus SP-43 2.5 ø4 Tip shape: One-sided cut Tip angle: 20º Tip shape: One-sided cut Tip angle: 20º 55 Tip shape: One-sided cut Tip angle: 20º Double-sided small hole arm stylus SPW-31 Double-sided small hole arm stylus SPW-32 Double-sided small hole arm stylus SPW-33 ø8 20 ø8 20 ø8 20 closeup of tip ø4 ø1.6 275 Tip shape:cone Tip angle: 30º tip radius: 25µm closeup of tip ø5 275 Tip shape:cone Tip angle: 30º tip radius: 25µm closeup of tip ø4 275 Tip shape:cone Tip angle: 30º tip radius: 25µm 13

Specifications Measuring range Detector (Z1 axis (detector unit)) Drive unit Accuracy (20 C) External dimensions (W D ) Mass Model Order No. CV-3200S4 CV-32004 CV-3200W4 CV-3200S8 CV-32008 CV-3200W8 218-491A 218-492A 218-493A 218-496A 218-497A 218-498A CV-4500S4 CV-45004 CV-4500W4 CV-4500S8 CV-45008 CV-4500W8 218-451A 218-452A 218-453A 218-456A 218-457A 218-458A X axis 100mm 200mm Z1 axis (detector unit) 60mm (±30mm in horizontal situation) Z2 axis (column) travel range 300mm 500mm 300mm 500mm Scale unit Resolution Stylus up/down motion Measuring direction Measuring face direction Measuring force Stylus traceable range Arc scale CV-3200 series: 0.04µm, CV-4500 series: 0.02µm Arc movement Both pulling and pushing directions CV-3200 series: Downward or upward CV-4500 series: Both upward and downward (direction switch from FORMTRACEPAK) CV-3200 series: 30mN (by adjusting weight) CV-4500 series: 10, 20, 30, 40, 50mN (Setting measuring force FORMTRACEPAK) Ascent 77, Descent 83 (with one-sided cut stylus: standard accessory) X axis Separate type linear encoder Scale unit Z2 axis (column) ABS encoder X axis 0.05µm Resolution Z2 axis (column) 1µm X axis 0-80mm/s and manual operation Drive speed Z2 axis (column) 0-30mm/s and manual operation Measuring speed X axis 0.02-5mm/s Straightness (when the X axis is horizontal) X axis 0.8µm/100mm 2µm/200mm X axis inclination angle X axis ±45 CV-3200 Series CV-4500 Series Main unit Controller Remote box X axis Z1 axis (column) X axis Z1 axis (column) ±(0.8 + 0.01L) µm L = Drive length (mm) Wide range: 1.8µm/100mm Narrow range: 1.05µm/25mm ±(0.8 + 0.02L) µm L = Drive length (mm) Wide range: 4.8µm/200mm Narrow range: 1.3µm/25mm ± (1.6 + 2 /100) µm = Measurement height from the horizontal position ±(0.8 + 0.01L) µm L = Drive length (mm) Wide range: 1.8µm/100mm Narrow range: 1.05µm/25mm 756 482 966mm ±(0.8 + 0.02L) µm L = Drive length (mm) Wide range: 4.8µm/200mm Narrow range: 1.3µm/25mm ±(0.8 + 2 /100) µm = Measurement height from the horizontal position 756 482 1166mm 1156 482 766 482 1176mm 966mm 221 344 490mm 248 102 62.2mm 766 482 1166mm 1166 482 1176mm Main unit 140kg 150kg 220kg 140kg 150kg 220kg Controller Remote box Operating temperature range Operating humidity range 14kg 0.9kg 15-25 C (within ±1K temperature fluctuation on calibration and measurement) 20-80%R (with no condensation) Storage temperature range 10 to 50 C Storage humidity range 5-90%R (with no condensation) 14

Dimensions CV-3200S4/4/W4, CV-4500S4/4/W4 Unit: mm 8 14 966 (1166) [1176] 854 (1054) [1054] 300 (500) [500] 110 [510] 100 228 220 386 T-groove 15 7 T-groove size (Common for all models) 100 [110] 46 85 12 600 [1000] 156 175 130 450 32 Measuring range CV-3200S8/8/W8, CV-4500S8/8/W8 ( ): CV-32004, CV-45004 [ ]: CV-3200W4, CV-4500W4 The CV-3200 series detector comes with weights for adjusting the measuring force. CV-3200 60 [460] 200 178 966 (1166) [1176] 854 (1054) [1054] 300 (500) [500] 20 486 T-groove 100 [110] 46 85 12 600 [1000] 156 166 175 130 450 32 Measuring range ( ) : CV-32008, CV-45008 [ ] : CV-3200W8, CV-4500W8 The CV-3200 series detector comes with weights for adjusting the measuring force. 15 CV-3200

One Number to Serve You Better 1-888-MITUTOYO (1-888-648-8869) Note: All information regarding our products, and in particular the illustrations, drawings, dimensional and performance data contained in this printed matter as well as other technical data are to be regarded as approximate average values. We therefore reserve the right to make changes to the corresponding designs. The stated standards, similar technical regulations, descriptions and illustrations of the products were valid at the time of printing. In addition, the latest applicable version of our General Trading Conditions will apply. Only quotations submitted by ourselves may be regarded as definitive. Specifications are subject to change without notice. Mitutoyo products are subject to US Export Administration Regulations (EAR). Re-export or relocation of our products may require prior approval by an appropriate governing authority. Aurora, Illinois (Corporate eadquarters) Westford, Massachusetts untersville, North Carolina Mason, Ohio Plymouth, Michigan City of Industry, California Birmingham, Alabama Trademarks and Registrations Designations used by companies to distinguish their products are often claimed as trademarks. In all instances where Mitutoyo America Corporation is aware of a claim, the product names appear in initial capital or all capital letters. The appropriate companies should be contacted for more complete trademark and registration information. 2012 Mitutoyo America Corporation, Aurora IL 3M 1111-07 Printed in USA, May 2012 Precision is our Profession