AC-DC 85-50 Watts AHM Series IT & Medical Approvals xppower.com Energy Efficiency Level V, CEC008 & EISA 007 <0.5 W No Load Input Power Class I and Class II Models (Except AHM50) Very High Efficiency IP Environmental Rating 3 Year Warranty Specification Input Input Voltage Input Frequency Input Current Inrush Current Power Factor 80-64 VAC (see derating curve) 47-63 Hz 85 W: 0.8 A at 5 VAC, 0.4 A 00 W:.0 A at 5 VAC, 0.5 A 50 W:.5 A at 5 VAC, 0.75 A 80 W:.7 A at 5 VAC, 0.9 A 50 W:.3 A at 5 VAC, 0.9 A at 30 VAC 70 A typical, 0 A max at 30 VAC, cold start at 5 C >0.9 at 5 VAC, 60 Hz at 50 VAC Earth Leakage Current 85 W: 70 µa typical, 80 µa max 00 W: 70 µa typical, 80 µa max 50 W: 80 µa typical, 00 µa max 80 W: 80 µa typical, 00 µa max 50 W: 80 µa typical, 00 µa max at 64 VAC/60 Hz Input Protection 85 W: Internal T.5 A/50 V 00 W: Internal T.5 A/50 V 50 W: Internal T4.0 A/50 V 80 W: Internal T4.0 A/50 V 50 W: Internal T6.3 A/50 V fuse in line and neutral No Load Input Power <0.5 W Output Output Voltage See tables Output Voltage Trim Not user-adjustable Minimum Load No minimum load required Start Up Delay 00-300 ms typical, model dependant () Hold Up Time 0 ms typical Line Regulation ±.5% maximum Load Regulation ±3.0% maximum Transient Response 5% max. deviation, recovery to within % in 500 µs for a 5% load change Ripple & Noise Typically less than %,.5% max pk-pk () Overvoltage Protection 5% typical, Recycle input to reset Overtemperature Unit shuts down, auto recovery Protection Overload Protection 5-75%, auto recovery Short Circuit Protection Trip and restart (hiccup mode) Temperature 0.05 %/ C Coefficient General Efficiency 9% typical Energy Efficiency Level V Isolation 4000 VAC In to Out, x MOPP 500 VAC In to Earth, x MOPP 500 VAC Out to Earth, x MOPP Switching Frequency 45-00 KHz variable Power Density 4.4-5.7 W/in 3 MTBF 53 khrs typical to MIL-HDBK-7F at 5 C, GB Environmental Operating Temperature 0 C to +60 C, derate linearly from 00% power at +40 C to 60% power at +60 C Cooling Convection-cooled Operating Humidity 5-95% RH, non-condensing Storage Temperature -40 C to +85 C Operating Altitude 3000 m Shock 3 x 30 g/ ms shocks in both +ve & -ve directions along the 3 orthogonal axis, total 8 shocks. Vibration Three axis 5-500 Hz at g x 0 sweeps EMC & Safety Emissions Harmonic Currents Voltage Flicker ESD Immunity Radiated Immunity EFT/Burst EN550/, class B conducted EN550/, class B radiated EN6000-3-, class A EN6000-3-3 EN6000-4-, level 3, Perf Criteria A EN6000-4-3, level 3, Perf Criteria A EN6000-4-4, level 3, Perf Criteria A Surge EN6000-4-5, installation class 3, Perf Criteria A Conducted Immunity EN6000-4-6, level 3, Perf Criteria A Magnetic Field EN6000-4-8, level 3, Perf Criteria A Dips & Interruptions EN6000-4-, EN6060-- Safety Approvals EN6060-, ANSI/AAMI ES6060-, CSA. No. 6060- per cul, Including Risk Management, EN60950, UL60950. Denan (PSE) certification. See longform datasheet for further information.. Measured at the end of the output cable with 0 µf electrolytic and 0. µf ceramic capacitor.
Models and Ratings AHM85 Output Power Output Voltage Output Current Model Number () 85 W.0 VDC 7.08 A AHM85PS 85 W 5.0 VDC 5.67 A AHM85PS5 85 W 9.0 VDC 4.47 A AHM85PS9 85 W 4.0 VDC 3.54 A AHM85PS4 85 W.0 VDC 7.08 A AHM85PSC 85 W 5.0 VDC 5.67 A AHM85PS5C 85 W 9.0 VDC 4.47 A AHM85PS9C 85 W 4.0 VDC 3.54 A AHM85PS4C AC-DC. Models with suffix C have a Class II equipment protection classification.. For IEC30-C8 input connector with Class II models, add suffix -8 to the model number, e.g. AHM85PS4C-8. 3. For optional input connector retention clip, add suffix -A to the model number e.g. AHM85PS4C-A. 4. Alternate case colours available for OEM quantities, contact sales for information. 5.9 (50.0) 36.4 (900.0) 0.79 (Ø0).5 (64.0).4 (36.0) 5. (30.0) IEC30-C4.45 (37.0) 3.0 (76.9).55 (39.4).57 (40.0) 5. (30.0) Standard (Class I) C Models (Class II) C-8 Models (Class II).40 (35.7) 4 3 IEC 30-C4 IEC 30-C8 IEC 30-C8 Pin Output + Pin Output + GND* C Models. Tolerance is 0.0 (0.5) maximum, except output cable length.. Weight 0.9 lbs (400 g). 3. Dimensions shown in inches (mm). 4. Alternate case colours available for OEM quantities, contact sales for information
AC-DC Models and Ratings. Models with suffix C have a class II equipment protection classification.. For IEC30-C8 input connector with class II models, add suffix -8 to the model number, e.g. AHM00PS4C-8. AHM00 Output Power Output Voltage Output Current Model Number () 00 W.0 VDC 8.33 A AHM00PS 00 W 5.0 VDC 6.67 A AHM00PS5 00 W 9.0 VDC 5.6 A AHM00PS9 00 W 4.0 VDC 4.6 A AHM00PS4 00 W 48.0 VDC.08 A AHM00PS48 00 W.0 VDC 8.33 A AHM00PSC 00 W 5.0 VDC 6.67 A AHM00PS5C 00 W 9.0 VDC 5.6 A AHM00PS9C 00 W 4.0 VDC 4.6 A AHM00PS4C 00 W 48.0 VDC.08 A AHM00PS48C 3. For optional input connector retention clip, add suffix -A to the model number e.g. AHM00PS4C-A. 4. Alternate case colours available for OEM quantities, contact sales for information. 0. (5.0) 6.9 (60.0) 36.4 (900.0) 0.79 (Ø0).5 (64.0).4 (36.0) 5. (30.0).45 (37.0) 3.0 (76.9).55 (39.4).57 (40.0) 5. (30.0) Standard (Class I) C Models (Class II) C-8 Models (Class II).40 (35.7) 4 3 IEC 30-C4 IEC 30-C8 IEC 30-C8 Pin Output + Pin Output + GND* C Models. Tolerance is 0.0 (0.5) maximum, except output cable length.. Weight. lbs (500 g). 3. Dimensions shown in inches (mm).
Models and Ratings AHM50 Output Power Output Voltage Output Current Model Number () 50 W.0 VDC.50 A AHM50PS 50 W 5.0 VDC 0.00 A AHM50PS5 50 W 9.0 VDC 7.89 A AHM50PS9 50 W 4.0 VDC 6.5 A AHM50PS4 50 W 48.0 VDC 3.3 A AHM50PS48 50 W.0 VDC.50 A AHM50PSC 50 W 5.0 VDC 0.00 A AHM50PS5C 50 W 9.0 VDC 7.89 A AHM50PS9C 50 W 4.0 VDC 6.5 A AHM50PS4C 50 W 48.0 VDC 3.3 A AHM50PS48C AC-DC. For optional input connector retention clip, add suffix -A to the model number e.g. AHM50PS4-A. Models with suffix C have a class II equipment protection classification. For IEC30-C8 input connector with class II models, add suffix -8 to the model number, e.g. AHM50PS4C-8.. Alternate case colours available for OEM quantities, contact sales for information. Dimensions shown in inches (mm). 0.9 (4.9) 7.8 (00.0) 36.4 (900.0) 0.79 (Ø0) 3.5 (80.0).4 (36.0) 5. (30.0) IEC30-C4.45 (37.0) 3.94 (00.3).0 (5.5).58 (40.30) 6.8 (73.0) Standard (Class I) C Models (Class II) C-8 Models (Class II) IEC 30-C4 IEC 30-C8 IEC 30-C8.40 (35.7) 4 3 Pin Output + Pin Output + GND* C Models. Tolerance is 0.0 (0.5) maximum, except output cable length.. Weight.3 lbs (600 g).
AC-DC Models and Ratings AHM80 Output Power Output Voltage Output Current Model Number 65 W.0 VDC 3.75 A AHM80PS 80 W 5.0 VDC.00 A AHM80PS5 80 W 9.0 VDC 9.47 A AHM80PS9 80 W 4.0 VDC 7.50 A AHM80PS4 80 W 48.0 VDC 3.75 A AHM80PS48 65 W.0 VDC 3.75 A AHM80PSC 80 W 5.0 VDC.00 A AHM80PS5C 80 W 9.0 VDC 9.47 A AHM80PS9C 80 W 4.0 VDC 7.50 A AHM80PS4C 80 W 48.0 VDC 3.75 A AHM80PS48C. For optional input connector retention clip, add suffix -A to the model number e.g. AHM80PS4-A. Models with suffix C have a class II equipment protection classification. For IEC30-C8 input connector with class II models, add suffix -8 to the model number, e.g. AHM80PS4C-8.. Alternate case colours available for OEM quantities, contact sales for information. Dimensions shown in inches (mm). 0.93 (4.9) 7.87 (00.0) 35.43 (900.0) 0.79 (Ø0.0) 3.5 (80.0).4 (36.0) 5. (30.0).6 (4.0) 3.94 (00.3).0 (5.5).58 (40.3) 6.8 (73.0) Standard (Class I) C Models (Class II) C-8 Models (Class II) IEC 30-C4 IEC 30-C8 IEC 30-C8.40 (35.7) 4 3 Pin Output + Pin Output + GND* C Models. Dimensions shown in inches (mm). Tolerance is 0.0 (0.5) maximum, except output cable length.. Weight.4 lbs (60 g)
Models and Ratings AHM50 Output Power Output Voltage Output Current Model Number () 0 W.0 VDC 7.50 A AHM50PST 0 W 5.0 VDC 4.66 A AHM50PS5T 40 W 9.0 VDC.63 A AHM50PS9T 50 W 4.0 VDC 0.4 A AHM50PS4T 50 W 48.0 VDC 5. A AHM50PS48T AC-DC. For optional input connector retention clip, add suffix -A to the model number e.g. AHM50PS4T-A.. For 6 pin DIN connector, remove T from the end of the model number e.g. AHM50PS4 (DIN connector for medical applications only). Dimensions shown in inches (mm). 0. (5.0) 8.8 (3.0) 8.58 (8.0) 35.43 (900.0) Standard Molex 6 pin Connector 0.79 (Ø 0.0) 3.484 (88.50).47 (36.0) IEC 30-C4 Optional 6 pin DIN connector shown (for medical applications only) 0.79 (Ø 0.0).457 (37.0) 0.063 (.60) 7.4 (88.40).47 (36.0) 4.34 (05.0).37 (60.0).97 (50.0) 5. (30.0).40 (35.7) 4 5 6 3 Pin No. OUTPUT CONNECTOR Molex Part No.: 50-36-67 DIN Part No.: DIN453 Pin Return Output + Pin Return Return Return Pin 4 Output + Return Pin 5 Output + Output + Pin 6 Ouput + Ouput + GND* IEC 30-C4 Derating Curve 6 5 3 4. Dimensions shown in inches (mm). Tolerance is 0.0 (0.5) maximum, except output cable length.. Weight. lbs (000 g). 00 90 Output Power (%) 80 70 60 50 40 AHM85,00,50 & 80 Models AHM50 Models 80 85 90 00 0 40 50 64 4-Jul-4