eatm tmanager Release 2.5

eatm tmanager Release 2.5 Quick Start Manual IMPORTANT! Befre yu prceed, STOP and REGISTER yur mdule On ur website at http://www.ldi.cm/prduct registratin Ethernet 1 = 192.168.1.254 FACTORY DEFAULTS: Ethernet 2 = DHCP Nte: IP addresses will be scrlling n the mdule s 4-character display LOGIN Username = admin Passwrd = admin

Table f Cntents eatm tmanager : Overview and Installatin... 1 Overview... 1 Definitin f terms that will be used thrughut the dcument:... 1 Hardware and Sftware Installatin... 2 eatm tmanager: xatm Manager... 3 Cnnecting t the eatm tmanager... 3 Cnfiguring the Ethernet Prts... 4 Setting the Time n the eatm tmanager... 5 eatm tmanager : Prject Editr... 6 Cnfiguratin Overview... 6 Creating New Prject... 7 Using xatm Manager Sftware... 7 Using the Prject Editr sftware... 7 Adding a Cntrller (Autmatin Adapter)... 8 Adding PLC Endpints... 9 Adding Triggers... 10 Trigger cnditin ptins:... 10 Adding a Database Adapter (MSSQL)... 11 Adding Database Endpints (MSSQL)... 12 Adding Maps... 13 Output Schema:... 13 Input Schema:... 14 Cnnecting Outputs t Inputs:... 15 Adding a Database Message Path... 16 Starting Cmpnents... 17 Starting a Trigger... 17 Starting an Endpint... 18 Starting a Prject... 18 Starting an Appliance... 19 If yu wish t use the Knwledge Base r cntact Custmer Supprt yu can : Frm within the xatm Manager r Prject Editr sftware, select the HELP icn r Visit www.ldi.cm and select Supprt. and then Online Supprt

Mnitring Status... 19 FAQ: Hw d I add my CLX prfile?... 1 Adding CLX prfile supprt (i.e. Supervisry Cntrller)... 1 CLX Prfile (AOP): Status and cmmand t/frm CLX... 1 Status and Cntrl infrmatin... 2 FAQ: What advanced netwrk settings are supprted?... 3 What ptins are available under Netwrk Diagnstics?... 4 What ptins are available using Netwrk Ruting?... 6 FAQ: What causes the mdule t time sync?... 7 FAQ: What happens if ne r mre f the plc variables are nt available when the trigger fires?... 7 Can I use multiple PLCs my map as the surce r destinatin?... 7 Appendix A: Truble shting... 1 xatm Manager: Attentin Required... 1 Warning: Maximum number f any cmpnent type have been reached... 2 Trigger: Shuld be firing but is nt... 2 ICON: Pssible Trigger/Endpint icn states... 3 PrjectEditr: Clearing Lcks... 4 Errr: the destinatin fr the return map must be the autmatin adapter... 5 Prject: Type Warning... 6 Prject: Dependent Objects Warning... 7 Netwrk trubleshting... 7 Appendix B: Recmmended Usage... 1 Cnfiguratin design... 1 Transactin Lg... 3 Stre & Frward (S&F)... 4 Autmatin EndPints... 5 Appendix C: eatm tmanager Limits... 1 Cnfiguratin Sftware... 1 Appliance Cnfiguratin... 1 Appendix D: Functinality and Hierarchy f the Cnfiguratin Prgrams... 1 If yu wish t use the Knwledge Base r cntact Custmer Supprt yu can : Frm within the xatm Manager r Prject Editr sftware, select the HELP icn r Visit www.ldi.cm and select Supprt. and then Online Supprt

Appendix E: Minimum System Requirements... 1 If yu wish t use the Knwledge Base r cntact Custmer Supprt yu can : Frm within the xatm Manager r Prject Editr sftware, select the HELP icn r Visit www.ldi.cm and select Supprt. and then Online Supprt

eatm tmanager Release 2.5 Page 1 eatm tmanager : Overview and Installatin Overview The eatm tmanager appliance prvides a safe and reliable methd f transmitting data between cntrllers and business systems (databases, JMS applicatins, etc.). Fr a cmplete list f supprted cmmunicatin methds, check the prduct datasheet at www.ldi.cm. This manual will guide yu thrugh a simple installatin. Fr mre infrmatin n any screen, reference the sftware s nline help. T cnfigure the eatm tmanager yu need t: 1. Define access t the appliance (netwrk, users, etc) 2. Create yur prject 3. Cnfigure prject cmpnents (adapters, endpints, data maps, triggers, etc.) 4. Place the abve cmpnents, prject and appliance int RUN mde After yu cmplete these steps the appliance will be able t transmit data. Definitin f terms that will be used thrughut the dcument: Muse Usage: Duble click t select. Right click t view a menu f ptins. Hver Muse t display a descriptin f the icn. Edit screens: Edit: Puts the bject in edit mde OK: Saves the bject and clses the pane Apply: Saves the bject withut clsing the pane Cancel: Clses the pane withut saving changes Status Indicatrs : This includes triangles, squares, text clrs, and exclamatin marks (!). GREEN means RUNNING and active. RED means STOPPED r HALTED r ERROR. YELLOW means trigger has faulted due t data transfer errrs. GRAY means set t RUNNING, but nt ACTIVE because its hierarchy is nt started/running. If yu wish t use the Knwledge Base r cntact Custmer Supprt yu can : Frm within the xatm Manager r Prject Editr sftware, select the HELP icn r Visit www.ldi.cm and select Supprt. and then Online Supprt

eatm tmanager Release 2.5 Page 2 Hardware and Sftware Installatin 1. Plug the eatm tmanager securely int the CntrlLgix chassis. 2. There are tw Ethernet prts n the appliance. These prts are electrically islated frm each and can be used t cnnect t different subnets. Cnnect cables t the Ethernet 1 and/r Ethernet 2 prts n the frnt f the eatm tmanager NOTE Crssver cable : If yu are cnnecting directly frm a PC t an eatm tmanager, yu can use the included crssver cable. In yur PC s Netwrk Cntrl Panel, in the TCP/IP sectin, set yur IP address t 192.168.1.x, and yur subnet t 255.255.255.0.Cnnect t the eatm tmanager s factry default address f 192.168.1.254 NOTE License Keys : All license keys cme pre installed n the eatm tmanager. Yur cnfiguratin firmware may be installed n multiple PC systems fr supprt f the eatm tmanager appliances. See the License Agreement included with the prduct. 3. Install the cnfiguratin sftware. After the installatin is cmplete, the cmputer s Start / All Prgrams menu will have a listing fr Online Develpment Inc / tmanager eatm and its tw cmpnents Prject Editr and xatm Manager. These tw cnfiguratin prgrams require that the eatm tmanager be nline when they are used. NOTE Cnfiguratin Prgrams Overview : The xatm Manager sftware is used t cnfigure administrative items (netwrk settings, time zne, time sync, etc.) fr each eatm tmanager appliance. The Prject Editr sftware is used t cnfigure cnnectins and their transactins. A map f the menu system fr each f these prgrams is prvided in Appendix D. If yu wish t use the Knwledge Base r cntact Custmer Supprt yu can : Frm within the xatm Manager r Prject Editr sftware, select the HELP icn r Visit www.ldi.cm and select Supprt. and then Online Supprt

eatm tmanager Release 2.5 Page 3 eatm tmanager: xatm Manager In this sectin f the manual we will use the xatm Manager sftware t establish a cnnectin between the cmputer and the eatm tmanager, cnfigure its Ethernet prts, and synchrnize its time. Cnnecting t the eatm tmanager 1. Launch the xatm Manager cnfiguratin sftware. 2. In the upper right crner f the screen, type in the IP address f the eatm tmanager appliance. NOTE IP Address : Cnnected IP addresses will be scrlling acrss the frnt f the eatm tmanager. The default is 192.168.1.254 3. Press the RED Cnnectin icn. 1. When prmpted, enter yur username and passwrd and press Lgin. NOTE Username and Passwrd : The default username is admin and the default passwrd is admin. After yu successfully cnnect, the Cnnectin icn will turn GREEN, as shw belw. If yu wish t use the Knwledge Base r cntact Custmer Supprt yu can : Frm within the xatm Manager r Prject Editr sftware, select the HELP icn r Visit www.ldi.cm and select Supprt. and then Online Supprt

eatm tmanager Release 2.5 Page 4 Cnfiguring the Ethernet Prts 1. Select the Administratin tab 2. Select the Netwrk tab. T cnfigure an Ethernet prt: Duble click n the Ethernet1 r Ethernet2 prt t edit it. Make all required changes fr the prt and exit by selecting OK. During the edit f a prt s cnfiguratin, if yu select the Advanced Settings icn, yu will be given access t additinal netwrk settings that yu can mdify. See FAQ sectin f this dcument What advanced netwrk settings are supprted? fr mre infrmatin. Infrmatin n the Netwrk Diagnstics and Netwrk Rutes ptins are available in the FAQ sectin f this dcument. If yu wish t use the Knwledge Base r cntact Custmer Supprt yu can : Frm within the xatm Manager r Prject Editr sftware, select the HELP icn r Visit www.ldi.cm and select Supprt. and then Online Supprt

eatm tmanager Release 2.5 Page 5 Setting the Time n the eatm tmanager The eatm tmanager s time clck can by synced with a variety f devices. In this example, we will sync it with the cmputer s clck. 1. Select Time Management. 2. Select Get Lcal Cmputer Time. 3. Select Set Appliance Time. If yu wish t use the Knwledge Base r cntact Custmer Supprt yu can : Frm within the xatm Manager r Prject Editr sftware, select the HELP icn r Visit www.ldi.cm and select Supprt. and then Online Supprt

eatm tmanager Release 2.5 Page 6 eatm tmanager : Prject Editr Cnfiguratin Overview We will nw start using the Prject Editr sftware t define cnnectins. The eatm tmanager cnfiguratin is based arund the cncept f ENDPOINTS. The destinatin fr all data transfers is an ENDPOINT. Fr example, a CntrlLgix prcessr is an ENDPOINT, an ORACLE database is an ENDPOINT, a MSSQL database is an ENDPOINT. Each adapter can have multiple ENDPOINTS An ENDPOINT is used t define the PROPERTIES fr that cnnectin t the destinatin. Fr example, will the cnnectin use Stre&Frward, Transactin Lgging r Fail Over? The eatm tmanager cnfiguratin is subdivided int PROJECTS. These PROJECTS wrk autnmusly t each ther. Multiple PROJECTS can be running at the same time. Each PROJECT includes the adapters and their ENDPOINTS, data mapping and trigger events used in that prject. When yu cnfigure the mdule (using the Prject Editr sftware) yu will: Define the access t the mdule (netwrk, users, etc) Create yur PROJECT and its cmpnents (adapters, ENDPOINTS, data maps, triggers, etc) Place the abve cmpnents, PROJECT and appliance int RUN mde After yu cmplete the abve steps yur mdule will begin transmitting data. In this manual we will step thrugh a simple installatin. When we define the prject cmpnents we will start at the tp (Adapters) and wrk ur way dwn the list. Fr mre infrmatin n any screen, reference the sftware s nline help by pressing [F1]. If yu wish t use the Knwledge Base r cntact Custmer Supprt yu can : Frm within the xatm Manager r Prject Editr sftware, select the HELP icn r Visit www.ldi.cm and select Supprt. and then Online Supprt

eatm tmanager Release 2.5 Page 7 Creating New Prject Yu have tw ptins when creating a new prject. Bth are shwn in this sectin. Using xatm Manager Sftware T create a prject frm within the xatm Manager sftware: 1. If it s nt already running, start the xatm Manager sftware. 2. Make sure yu are cnnected t the xatm_manager using the steps in the previus sectin. The Cnnectin icn shuld be GREEN. 3. Select the Prjects tab and then select New. 4. When prmpted, type in a prject Name and select OK. 5. Select yur new Prject and press Edit t pen the Prject Editr fr this new prject. Using the Prject Editr sftware T create a prject frm within the Prject Editr sftware: 1. Startup the Prject Editr sftware. 2. Cnnect t the eatm tmanager the same way yu did using the xatm Manger sftware. 3. Enter the IP address f yur appliance (the default is 192.168.1.254, but yu may have changed it in a previus sectin) and press the RED Cnnectin Icn. 4. Enter yur Username and Passwrd. Bth defaults are admin. 5. When the Select Prject screen. Appears, select New. 6. When prmpted, type in a Prject Name and select OK. 7. Select yur new Prject and press Edit. NOTE Prject Editr : The Prject Editr can nly view ne prject at a time. Yu may have multiple Prject Editrs pen at the same time, if needed. If yu wish t use the Knwledge Base r cntact Custmer Supprt yu can : Frm within the xatm Manager r Prject Editr sftware, select the HELP icn r Visit www.ldi.cm and select Supprt. and then Online Supprt

eatm tmanager Release 2.5 Page 8 Adding a Cntrller (Autmatin Adapter) Adapters define the surces and destinatins f the transactins. Each input adapter can cntain ne r mre Triggers and each utput adapter can cntain ne r mre Endpints. Sme adapters, such as the Autmatin Adapter, are bth input and utput adapters. The Autmatin Adapter allws the user t view and cnfigure cntrllers, bridges and ther devices in the industrial envirnment. This industrial envirnment is referred t as the Autmatin Tree (i.e. list f cntrllers, their tag/variable definitins, and the path t these cntrllers). The Autmatin Tree definitin is shared amng all prjects n the eatm tmanager appliance. The Autmatin Adapter is bth an input and an utput adapter. The Autmatin Adapter can cntain ne r mre Triggers. The Autmatin Adapter will cntain at least ne Endpint fr receiving infrmatin. 1. Open Adapters. 2. Right click n Autmatin and select Open. Wait a cuple f secnds and yu will see the cntents f the lcal rack. Clr Black Brwn Status in the Autmatin Tree Cre item label In this example, the lcal rack Item can be cnfigured, but is nt yet cnfigured Green Red Gray Blue Item is cnfigured Item is cnfigured & has an errr NOTE: Cursr ver the mdule t see the errr Item is in the rack/bridge but cannt be cnfigured Item is an eatm frnt prt driver When yu right click n an individual mdule, yu will see the ptins available fr that mdule. 3. Click n the Lgix prcessr, right click and then select Cnfigure the selected mdule. 4. Enter a unique name fr this Autmatin device. Name: Label fr the PLC. This name will be used fr the tag list which will cntain the tags frm this device. Slt Number: The backplane slt number f the PLC. The current slt value will be displayed. Msg Respnse Timeut: The time perid the scanner will wait befre assuming the cnnectin with the PLC is brken. If yu wish t use the Knwledge Base r cntact Custmer Supprt yu can : Frm within the xatm Manager r Prject Editr sftware, select the HELP icn r Visit www.ldi.cm and select Supprt. and then Online Supprt

eatm tmanager Release 2.5 Page 9 5. Select OK and the eatm tmanager will request the tag list frm the cntrller. Nte Tag List : All defined prcessrs have a list f variables under Tag Lists in the left clumn. Yu can als access the Tag List by right clicking n the prcessr and selecting Open Tag List. Nte Update Tag List : Update tag list will be used later t request an updated tag list frm the prcessr. This update is necessary when tags have been added r remved frm the prcessr. Adding PLC Endpints An endpint defines the destinatin f a data transfer. 1. Right click n Autmatin. 2. Select New Endpint. 3. Enter a unique name fr this Autmatin endpint. 4. Select OK. Name: The name f the endpint. Adapter: The name f the adapter that the endpint belngs t. The link buttn pens the adapter fr viewing r editing. If Use Flw Cntrl is set, the user can regulate the flw f messages writing t Autmatin (PLC) tags. Mre details are cvered in Appendix B. If yu wish t use the Knwledge Base r cntact Custmer Supprt yu can : Frm within the xatm Manager r Prject Editr sftware, select the HELP icn r Visit www.ldi.cm and select Supprt. and then Online Supprt

eatm tmanager Release 2.5 Page 10 Adding Triggers A trigger specifies when data is transacted frm the cntrller t the business envirnment r when data is read frm the business envirnment and sent t the cntrller. 1. Right click n Autmatin. 2. Select New Trigger. 3. Enter a Name fr the trigger. 4. Select the Type: Scheduled, Peridic r Event Scheduled the trigger fires at a scheduled time if its cnditins are met. The CONDITIONAL TAGS (if defined) are read at the scheduled time and the cnditin is evaluated. If scheduled cnditins and the tag cnditins are TRUE, the trigger fires. Peridic scans the CONDITIONAL TAGS every scan perid t see if the cnditin is met. If the cnditin is TRUE, the trigger fires Event when the specified event ccurs (i.e. CLX MSG INSTRUCTION is enabled), the CONDITIONAL TAGS (if any) are then read and the cnditin is evaluated. If bth cnditins are TRUE, the trigger fires CONDITIONAL TAGS are defined in the Variable and Reference fields. The Reference field may include a variable frm any cntrller r a cnstant. Select OK. Trigger cnditin ptins: Evaluate every: Mnth Select the day f the mnth and the time f day when the trigger will be evaluated Week Select a day f the week and the time f day when the trigger will be evaluated Day Enter the time f day when the trigger will be evaluated Hur Enter the minutes and secnds after the hur when the trigger will be evaluated Minute Enter the secnds after the minute when the trigger will be evaluated Cnditin (available fr bth Peridic and Scheduled triggers): ALWAYS always fires NEVER never fires CHANGE fires n change f state LT fires when Cmpare Value 1 < Cmpare Value 2 LTE fires when Cmpare Value 1 <= Cmpare Value 2 GT fires when Cmpare Value 1 > Cmpare Value 2 GTE fires when Cmpare Value 1 >= Cmpare Value 2 EQ fires when Cmpare Value 1 = Cmpare Value 2 NEQ fires when Cmpare Value 1 <> Cmpare Value 2 BAND (Bitwise AND) fires when Cmpare Value 1 bitwise ANDed with Cmpare Value 2 is nn zer ELT, ELTE, EGT, EGTE, EEQ, ENEQ, EBAND these cnditins are the same as the cnditins abve with the exceptin that these cnditins are edge trigger cnditins. They nly fire nce when the Cnditin evaluates t TRUE. The Trigger will fire again nce when the Cnditin evaluates t FALSE, then TRUE. If yu wish t use the Knwledge Base r cntact Custmer Supprt yu can : Frm within the xatm Manager r Prject Editr sftware, select the HELP icn r Visit www.ldi.cm and select Supprt. and then Online Supprt

eatm tmanager Release 2.5 Page 11 Adding a Database Adapter (MSSQL) A MSSQL Adapter is an utput adapter and it allws yu t setup a cnnectin t a MSSQL database. 1. Right click n Adapter. 2. Select New Adapter. 3. Select New MSSQL Adapter. 4. Define the Name used t label this device in the eatm tmanager. 5. Define the Hst by either IP address r DNS name. 6. Define the Prt this database server listens n. Fr MS SQL, the default is 1433; fr Oracle the default is 1521. The default prt fr that database type is shwn. 7. Input the Database Name as seen n the database server. 8. Input the Username and Passwrd as defined fr yur access int the database server. 9. Select Validate Cnnectin. This validatin attempts a cnnectin t the database t cnfirm that the netwrk settings are cnfigured crrectly. 10. Select Enumerate Database. The eatm tmanager will request the table, view, and stred prcedure infrmatin frm the database. 11. Select OK. Cnnectin Timeut (sec): The time in secnds the adapter attempts t cnnect t the database befre the cnnectin fails and messages g int the stre and frward queue r are drpped. Transactin Timeut (sec): The time in secnds the adapter attempts t send a transactin t the database befre the cnnectin fails and messages g int the stre and frward queue r are drpped. If yu wish t use the Knwledge Base r cntact Custmer Supprt yu can : Frm within the xatm Manager r Prject Editr sftware, select the HELP icn r Visit www.ldi.cm and select Supprt. and then Online Supprt

eatm tmanager Release 2.5 Page 12 Adding Database Endpints (MSSQL) As an utput adapter, the MSSQL adapter can cntain ne r mre endpints. 1. Right click n MSSQL Device Adapter. 2. Select New Endpint. 3. Enter a Name fr this endpint. Adapter: The name f the adapter that the endpint belngs t. The Link buttn pens the adapter fr viewing r editing. These ptins are cvered in Appendix B: Database Endpint : Transactin Lg (ptinal) Database Endpint : Stre & Frward (ptinal) Database Endpint : Failver (ptinal) If yu wish t use the Knwledge Base r cntact Custmer Supprt yu can : Frm within the xatm Manager r Prject Editr sftware, select the HELP icn r Visit www.ldi.cm and select Supprt. and then Online Supprt

eatm tmanager Release 2.5 Page 13 Adding Maps The next step is t define the mapping f surce data t its destinatin by creating a map. Yu can create a unidirectinal map t map data frm a surce t a destinatin, r a functin map t map data frm a surce t parameters in a functin call and utputs frm the functin call t a destinatin. In this sectin we will be creating a unidirectinal map. Our example will use a MSSQL database table insert, a CntrlLgix tag, and a cuple f eatm macr values. 1. Right click n Maps. 2. Select New Map. 3. Select New Unidirectinal Map. Output Schema: 1. Select Output Schema. 2. Select a Table frm the Tables in yur database. 1. Yu may nly select frm ne table. In the example the table named AUTO was selected. 2. When yu select the table, the table cntents will be shwn in new windw. If yu wish t use the Knwledge Base r cntact Custmer Supprt yu can : Frm within the xatm Manager r Prject Editr sftware, select the HELP icn r Visit www.ldi.cm and select Supprt. and then Online Supprt

eatm tmanager Release 2.5 Page 14 3. With the cnfiguratin f the table displayed, yu will nw be able t drag clumn names frm the Schema screen int the Output Schema (right side) f the Map screen. 4. Select OK when yu are dne. Input Schema: The prcess will nw be repeated fr the Tags frm the PLC. 1. Select Input Schema. The screen will display a list f pssible Input surces. 2. Select Autmatin. 3. Select the name f the PLC yu want t map t. 4. The Tags available frm this prcessr are nw displayed in a Tag windw. Drag the nes yu want int the Input Scheme area n the left side f the Map screen. If yu wish t use the Knwledge Base r cntact Custmer Supprt yu can : Frm within the xatm Manager r Prject Editr sftware, select the HELP icn r Visit www.ldi.cm and select Supprt. and then Online Supprt

eatm tmanager Release 2.5 Page 15 Cnnecting Outputs t Inputs: T cmplete the map definitin, the inputs need t be cnnected t utputs. 1. Highlight ne r mre items. 2. Press the icn r right click and select Cnnect Input t Facing. 3. Repeat steps 1 and 2 until all the inputs are mapped. NOTE Cnnecting Inputs t Outputs : Yu can map ne input t multiple utputs if needed. Yu can select multiple inputs and utputs with ne Cnnect Input t Facing statement. Inputs can be values supplied by eatm tmanager Macrs Cnstants Timestamp Trigger Name including path Value f the tags used in the trigger cnditin (Variable and Reference) Reference the nline Help fr mre infrmatin When yu have cmpleted yur mapping, the screen will shw all inputs mapped t an utput. 4. Select OK t save and clse. If yu wish t use the Knwledge Base r cntact Custmer Supprt yu can : Frm within the xatm Manager r Prject Editr sftware, select the HELP icn r Visit www.ldi.cm and select Supprt. and then Online Supprt

eatm tmanager Release 2.5 Page 16 Adding a Database Message Path In this example, we will create an SQL Insert Message Path t insert data int a database using an SQL INSERT statement. 1. Right click n Message Paths. 2. Select New Path. 3. Select New SQL Insert Message Path. Name: The name f the message path. Triggers: The triggers that fire this message path. T fill this field, drag a trigger frm the tree n the left. Map: The map the message path uses. T fill this field, drag a map frm Lists cnfigured maps n the left. Endpint: The endpint the message path sends data t. T fill this field, drag an endpint frm the tree n the left. 4. Drag items that yu have already created frm the cnfigured items int the message path fields fr Triggers, Map, and Endpint. 5. Select OK t save and clse If yu wish t use the Knwledge Base r cntact Custmer Supprt yu can : Frm within the xatm Manager r Prject Editr sftware, select the HELP icn r Visit www.ldi.cm and select Supprt. and then Online Supprt

eatm tmanager Release 2.5 Page 17 Starting Cmpnents A cmpnent at any level can be stpped. The fllwing may be stpped eatm Appliance Prjects Triggers Endpints In rder fr a transactin t be cmpleted, all f the cmpnents must be Started (Running). Starting a Trigger When a trigger is Stpped, its icn will be displayed with a RED Bx as shwn belw. In Prject Editr, yu can start triggers in several ways: Select the trigger, select Edit frm the tp menu bar, and then select Start. Select the trigger and press F5. Right Click n the trigger and select Run. After the trigger is started, it s icn will display a status triangle n the trigger icn (either gray r green depending n the Prject and Mdule status).. NOTE: If either the Prject r Mdule is nt running, the icn triangle will be gray. If yu wish t use the Knwledge Base r cntact Custmer Supprt yu can : Frm within the xatm Manager r Prject Editr sftware, select the HELP icn r Visit www.ldi.cm and select Supprt. and then Online Supprt

eatm tmanager Release 2.5 Page 18 Starting an Endpint All f the Autmatin and Database endpints that are assciated with yur triggers need t be started. In Prject Editr, yu can start endpints the same way yu start triggers: Select the endpint, select Edit frm the tp menu bar, and then select Start. Select the endpint and press F5. Right Click n the endpint and select Run. Yu can als start endpints in xatm Manager: Right Click n the endpint and select Start. Starting a Prject There are several methds f starting a PROJECT: In Prject Editr, in the upper right crner, press the buttn in the Prject area. Select Yes when prmpted and the state will change t Running. In xatm Manager, select the Prjects r Status tab, right click n the prject name, and select Start. The prject ICON will change frm RED t GREEN. If yu wish t use the Knwledge Base r cntact Custmer Supprt yu can : Frm within the xatm Manager r Prject Editr sftware, select the HELP icn r Visit www.ldi.cm and select Supprt. and then Online Supprt

eatm tmanager Release 2.5 Page 19 Starting an Appliance An appliance can be started in either Prject Editr r xatm Manager. In the tp right crner f the screen, press the buttn in the Appliance area.. Select Yes when prmpted and the state will change t Running. Mnitring Status Nw that yu have started the cmpnents (trigger, endpint, prject and appliance), yu can mnitr the trigger and endpint status infrmatin easily n the PROJECTEDITOR S status screens. Yu can use these screens t Start, Stp, and access Transactin Lgs, and mnitr infrmatin during develpment. NOTE Viewing Status Infrmatin within xatm Manager vs. Prject Editr : This status infrmatin is available fr the whle mdule n the XATM_MANAGER STATUS screen by selecting VIEW TRIGGER / ENDPOINT STATUS. While the frmat is the same, the xatm Manager prvided infrmatin acrss the appliance (i.e. all prjects) and the Prject Editr can nly view ne prject at a time. Hwever, yu can have multiple Prject Editrs sessins pen at the same time, if needed. If yu wish t use the Knwledge Base r cntact Custmer Supprt yu can : Frm within the xatm Manager r Prject Editr sftware, select the HELP icn r Visit www.ldi.cm and select Supprt. and then Online Supprt

eatm tmanager Release 2.5 Page 20 In xatm Manager, yu can view trigger and endpint status by clicking n View Trigger /Endpint Status n the Status tab. If yu wish t use the Knwledge Base r cntact Custmer Supprt yu can : Frm within the xatm Manager r Prject Editr sftware, select the HELP icn r Visit www.ldi.cm and select Supprt. and then Online Supprt

eatm tmanager Release 2.5 FAQ 1 FAQ: Hw d I add my CLX prfile? Adding CLX prfile supprt (i.e. Supervisry Cntrller) The cnfiguratin fr the supervisry cntrller is made using the PROJECTEDITOR under the AUTOMATIONADAPTER. All Autmatin adapter cnfiguratins are in effect fr all the prjects n the mdule. Fr mst 56eATM tmanager installatins, yu will utilize the CLX AOP (Add On Prfile) s the default cnfiguratin is set the CONTROLMETHOD t BACKPLANE; therefre, n Supervisry Cntrller cnfiguratin changes are required. Hwever, yu will be using a CLX AOP (Add On Prfile) feature in RSLOGIX5000 t cnfigure a generic prfile fr yur tmanager. The instructins belw shw this RSLOGIX500 AOP cnfiguratin f yur generic prfile. CLX Prfile (AOP): Status and cmmand t/frm CLX Within RSLgix5000 sftware yu will need t setup a scheduled cnnectin using the CLX Generic Prfile. 1. Right click n I/O cnfiguratin and select New Mdule. 2. Under +Other, select Generic 1756 Mdule and select OK. 3. Setup yu mdule as shw in the screen capture (yur name, descriptin, and slt can differ). 4. Press OK. 5. Under the RSLgix5000 Cnnectin tab, set the packet interval t 20msec r greater ( 50msec recmmended) If yu wish t use the Knwledge Base r cntact Custmer Supprt yu can : Frm within the xatm Manager r Prject Editr sftware, select the HELP icn r Visit www.ldi.cm and select Supprt. and then Online Supprt

eatm tmanager Release 2.5 FAQ 2 Status and Cntrl infrmatin The fllwing infrmatin is passed using the supervisry cntrller cnnectin n matter which Cntrl Methd is selected. NOTE If a secnd cntrller needs t mnitr AOP : The appliance may nly have ne master fr mre infrmatin see the www.ldi.cm knwledgebase entry n Supervisry Cntrllers AOP HIERARCHY LOGIC. If yu wish t use the Knwledge Base r cntact Custmer Supprt yu can : Frm within the xatm Manager r Prject Editr sftware, select the HELP icn r Visit www.ldi.cm and select Supprt. and then Online Supprt

eatm tmanager Release 2.5 FAQ 3 FAQ: What advanced netwrk settings are supprted? During the edit f a prt s cnfiguratin, if yu select the Advanced Settings icn selectins: yu will given these If yu wish t use the Knwledge Base r cntact Custmer Supprt yu can : Frm within the xatm Manager r Prject Editr sftware, select the HELP icn r Visit www.ldi.cm and select Supprt. and then Online Supprt

eatm tmanager Release 2.5 FAQ 4 What ptins are available under Netwrk Diagnstics? T access Netwrk Diagnstics frm within xatm_manager sftware: 1. Select the Administratin tab. 2. Select the Netwrk tab. 3. Duble click n Netwrk Diagnstics See screen captures belw fr the available ptins. Online help is als available by pressing F1. If yu wish t use the Knwledge Base r cntact Custmer Supprt yu can : Frm within the xatm Manager r Prject Editr sftware, select the HELP icn r Visit www.ldi.cm and select Supprt. and then Online Supprt

eatm tmanager Release 2.5 FAQ 5 Fr AS400, iseries, System i users, yu will als see CWBPING. Use this cmmand t determine if a cnnectin can be successfully made t an iseries system, r t help determine the cause f a cnnectin failure. CWBPing checks the status f the hst servers n the iseries system. The name f the cmmunicatins prvider is shwn, as well as the result f cnnecting t each f the hst scket servers. T see detailed messages, use the (/v) verbse ptin available in the Online Help [F1]. If yu wish t use the Knwledge Base r cntact Custmer Supprt yu can : Frm within the xatm Manager r Prject Editr sftware, select the HELP icn r Visit www.ldi.cm and select Supprt. and then Online Supprt

eatm tmanager Release 2.5 FAQ 6 What ptins are available using Netwrk Ruting? T access Netwrk Diagnstics frm within xatm_manager sftware: 1. Select the Administratin tab. 2. Select the Netwrk tab. 3. Duble click n Netwrk Ruting See screen capture belw. Online help is als available n the unit by pressing F1. If yu wish t use the Knwledge Base r cntact Custmer Supprt yu can : Frm within the xatm Manager r Prject Editr sftware, select the HELP icn r Visit www.ldi.cm and select Supprt. and then Online Supprt

eatm tmanager Release 2.5 FAQ 7 FAQ: What causes the mdule t time sync? If time sync is enabled, a time synch cycle ccurs After a time synch cnfiguratin change After an appliance mde change During appliance bt At the specified frequency after cnfiguratin/mde-change-bt. During a time synch cycle: The time f the appliance is set frm the first active synch surce fund. All f the time synch destinatins are set frm the appliance time. Lgging -- Failed and successful synch surces and destinatins are lgged. FAQ: What happens if ne r mre f the plc variables are nt available when the trigger fires? Successful cmpletin f any map requires that all f its PLC variables must be available when: Fr inputs: When the trigger fires fr inputs Fr utputs: When it receives the utput values This is true fr all maps whether that map cntains ne plc r several plcs. If any PLC variable is nt available, the trigger is disabled and des nt cmplete until all variables are available. Can I use multiple PLCs my map as the surce r destinatin? Yu can map frm/t multiple input and/r utputs autmatin devices, if needed, in yur applicatin. Things t cnsider when yu make that decisin when using multiple autmatin devices: Successful cmpletin f this map requires that all f its PLC variables must be available when the trigger fires. This cnstraint is true fr all maps whether that map cntains ne plc r several plcs. If any PLC variable is nt available, the trigger is disabled and des nt cmplete until all variables are available. If this cnstraint is nt acceptable, limit yur maps t ne cntrller by use a single cntrller as a data cncentratr. If yu wish t use the Knwledge Base r cntact Custmer Supprt yu can : Frm within the xatm Manager r Prject Editr sftware, select the HELP icn r Visit www.ldi.cm and select Supprt. and then Online Supprt

eatm tmanager Release 2.5 Appendix A1 Appendix A: Truble shting xatm Manager: Attentin Required ATTENTION REQUIRED status is display in several lcatins: 1. The STS LED n the eatm appliance under the scrlling text display. It will blink RED if the ATTENTION REQUIRED status is set. 2. The screen icn is. a. On xatm Manager STATUS screen (as shwn belw) When yu hver the cursr ver this icn, yu will see the message belw Device requires attentin. Click fr mre details. When yu click fr mre details, yu will see a new windw (Events Requiring Attentin) listing all the errrs n the unit that have been lgged and nt yet acknwledged. This list will be sustained acrss eatm appliance restarts. NOTE: T acknwledge is t CLEAR frm the list. Yu may CLEAR ALL at this time, r individually by selecting the events and the CLEAR EVENTS ptin. b. Prject Editr tp tlbar When yu click this icn list., it will pen the xatm MANAGER s yu may review the events 3. SYSTEM LOG email ntificatin will ntify the user f the existence f an event. These events are marked as ERROR. If yu wish t use the Knwledge Base r cntact Custmer Supprt yu can : Frm within the xatm Manager r Prject Editr sftware, select the HELP icn r Visit www.ldi.cm and select Supprt. and then Online Supprt

eatm tmanager Release 2.5 Appendix A2 Warning: Maximum number f any cmpnent type have been reached If yu exceed any f the cnfiguratin cmpnent limits, yu will receive this errr message. This errr is displayed when yu attempt t create a new cmpnent. See Appendix C fr eatm tmanager Limit Values. Trigger: Shuld be firing but is nt If a trigger is nt running and yu believe that it shuld be, check the fllwing items: 1. Is the eatm appliance RUNNING? Lk in xatm Manager. 2. Is the Prject RUNNING? Lk in Prject Editr. If the eatm appliance is nt RUNNING and the Prject is running state is GRAY. ; hwever, if the eatm appliance is RUNNING, the state is in GREEN 3. If they are bth running, are the trigger and its endpints all in RUN? Right click and check STATUS the icn shuld have a GREEN triangle. 4. If they are then duble check the cnditins fr yur trigger. 5. Check the SYSTEM LOG fr errrs and If yu wish t use the Knwledge Base r cntact Custmer Supprt yu can : Frm within the xatm Manager r Prject Editr sftware, select the HELP icn r Visit www.ldi.cm and select Supprt. and then Online Supprt

eatm tmanager Release 2.5 Appendix A3 ICON: Pssible Trigger/Endpint icn states An item marked with the invalid icn means that the item is dependent n a variable which has either been deleted r the type has changed such that it is n lnger cmpatible with its usage. This wuld nrmally happen when yu update a tag list r schema. If yu hld the muse ver the invalid icn, a message is displayed describing the errr. A trigger marked with the faulted icn means that the PLC prgram des nt cntain ne f the tags used in the trigger cnditin r a map which the trigger is linked t. Mre infrmatin is available in the Prject Editr s nline HELP under Appliance Status. If yu wish t use the Knwledge Base r cntact Custmer Supprt yu can : Frm within the xatm Manager r Prject Editr sftware, select the HELP icn r Visit www.ldi.cm and select Supprt. and then Online Supprt

eatm tmanager Release 2.5 Appendix A4 PrjectEditr: Clearing Lcks When yu pen a selectin fr EDIT, yu create a lck n that cnfiguratin. If the Prject Editr is clsed prir t the exit f the EDIT mde, the next persn t cnnect t this prject will see this WINDOW when they pen cnnectin. Yu can select t UNLOCK all r any individual items. If yu wish t use the Knwledge Base r cntact Custmer Supprt yu can : Frm within the xatm Manager r Prject Editr sftware, select the HELP icn r Visit www.ldi.cm and select Supprt. and then Online Supprt

eatm tmanager Release 2.5 Appendix A5 Errr: the destinatin fr the return map must be the autmatin adapter This errr means that yu have selected an INBOUND MAP fr this SELECT Message Path which is nt mapping cntrller t database. Slutin: In this SELECT Message Path example, select a INBOUND MAP that maps database table infrmatin t autmatin tags. If yu wish t use the Knwledge Base r cntact Custmer Supprt yu can : Frm within the xatm Manager r Prject Editr sftware, select the HELP icn r Visit www.ldi.cm and select Supprt. and then Online Supprt

eatm tmanager Release 2.5 Appendix A6 Prject: Type Warning This warning will be displayed when yu APPLY r select OK (t save) and ne r mre f the INPUT fields n the left side are nt identical t the OUTPUT fields n the right side. This errr is infrming yu that yu are respnsible fr cnfirming the data types are cmpatible n these items. If yu wish t use the Knwledge Base r cntact Custmer Supprt yu can : Frm within the xatm Manager r Prject Editr sftware, select the HELP icn r Visit www.ldi.cm and select Supprt. and then Online Supprt

eatm tmanager Release 2.5 Appendix A7 Prject: Dependent Objects Warning If ther bjects related t the item are STARTED, yu will be asked if yu wish t STOP them t apply the EDIT that yu are nw saving. If yu select YES, yu will be supplied with a list f items that yu will nw want t restart. Warning: If yu select NO, yur changes are nt saved. Netwrk trubleshting See FAQ sectins f this dcument fr the NETWORK DIAGNOSTICS and NETWORK ROUTES If yu wish t use the Knwledge Base r cntact Custmer Supprt yu can : Frm within the xatm Manager r Prject Editr sftware, select the HELP icn r Visit www.ldi.cm and select Supprt. and then Online Supprt

eatm tmanager Release 2.5 Appendix B1 Appendix B: Recmmended Usage Cnfiguratin design FAQ: What d yu recmmend when designing my cnfiguratin? RESPONSE: The eatm tmanager prducts have several features that yu shuld keep in mind when designing yur cnfiguratin. 1. Triggers have several firing cnditin ptins: Optin 1: Tag based (up t 2 tags) typical selectin The use f tag includes cmparisn f a tag t a cnstant r t anther tag. These tags d nt have t reside n the same device. Optin 2: Time schedule Optin 3: CLX MSG INSTRUCTION Optin 4: Cmbinatins Multiple time schedule cnditins Time schedule cnditin(s) r MSG INSTRUCTION ptin cmbined with the Optin 1 cnditin methd. Nte: A trigger s transactin will nt be utput frm the tmanager if any f its map s input variables are nt available when the trigger fires. If any f these variables are nt available, the trigger is marked as disabled and will nt retry fr 60 secnds. 2. Handshake mde selectin made in the trigger cnfiguratin effects when the next trigger firing ccurs: When cmbining transactins under ne trigger, remember that the trigger cannt fire again until the cmpletin f all the messages at their level f handshaking; therefre, ne slw message wuld cause all t wait fr its cmpletin. A trigger will nt fire unless all f the tag/variable used in bth its trigger firing cnditins r its maps surce are nt available. This disabled state is signified in the PrjectEditr trigger name marked with a yellw triangle. When disabled, the trigger will nt fire any f its messages s n transactin will ccur until all the required data is available. If yu wish t use the Knwledge Base r cntact Custmer Supprt yu can : Frm within the xatm Manager r Prject Editr sftware, select the HELP icn r Visit www.ldi.cm and select Supprt. and then Online Supprt

eatm tmanager Release 2.5 Appendix B2 When selecting handshake mde, yu must cnsider the features that yu will be using with yur adapter endpint. Fr example: If yu are using STOREANDFORWARD, yu will use INQUE. typical selectin If yu want t stp the line if yur INSERT r UPDATE is nt cmpleted fr any reasn, yu will use SENTTODEST If yu want t stp the line if yur SELECT r STORED PROCEDURE WITH OUTPUTS is nt cmpleted fr any reasn, yu will use SENTTOSRC 3. Status Tags TriggerStatusTags typical selectin when trigger handshaking is required It is nly used if the plc lgic will be mnitring the cmpletin status f this individual trigger. Fr triggers with multiple message paths, there is the ptin f a separate status tag fr each message path. EndpintStatusTags They are nly used if the plc lgic will be mnitring the verall health f this cnnectin. It is verall health because its value will nly reflect the status f the last transactin t this endpint. 4. Endpint architecture Create separate endpints fr each adapter based n the prperties that yur transactin will require. Fr example, INSERTS and UPDATES sent t a database wuld always utilize STOREANDFORWARD. SELECT cmmands requests data frm the database wuld typically nt utilize STOREANDFORWARD StredPrcedures utilize STOREANDFORWARD r nt based n the functin t be perfrmed by this StredPrcedure If yu have a transactin message which might expect t be mre time cnsuming, then use a separate endpint t allw faster transactins t cntinue while the slwer transactin wait in the queue. 5. Map A transactin will nt be utput frm the tmanager if any f its map s input variables are nt available when the trigger sent its read request. At that time, this trigger is disabled and will nt retry fr 60 secnds. Map may cntain variables (i.e. tags) frm multiple plcs typical installatin, ne plc in a map If yu wish the trigger t cntinue when ne r mre f the plcs is nt available, then yu wuld use a data cncentratr CLX. In that situatin, the map wuld be using nly variables frm the data cncentratr plc. If yu wish t use the Knwledge Base r cntact Custmer Supprt yu can : Frm within the xatm Manager r Prject Editr sftware, select the HELP icn r Visit www.ldi.cm and select Supprt. and then Online Supprt

eatm tmanager Release 2.5 Appendix B3 Transactin Lg FAQ: Why wuld I use transactin lgging? And hw wuld I setup transactin lgging? Typical used fr nnautmatin endpints like databases and nt used fr AUTOMATION endpints RESPONSE: There are a few reasns. I wuld recmmend the use f transactin lgging with nn AUTOMATION endpints. Why? If any f the fllwing are true: 1. If yu wuld like t see the SQL message sent t the database and its respnse Nte Transactin lg cntents : This feature is useful in truble shting because bth the SUCCESSFUL and UNSUCCESSFUL transactins are lgged. If UNSUCCESSFUL, the database errr message is included in the lg. 2. If yu wuld like a histrical recrd f what yu sent. Nte Autmatic Exprt f mdule lgs : Yu can have it autmatically exprt via FTP r SMTP when a file becmes full. This feature is recmmended if yu wish t maintain this infrmatin fr lnger perids f time. 3. Yu have mre than 2G available fr the strage f yur S&F and transactin lg n yur eatm appliance s cmpact flash. Therefre, define yur S&F and Transactin lg sizes apprpriately. Nte Transactin Lg memry allcatin & impact n thrughput speed : These files will be created when yu save (select OK). Fr high speed applicatins, yu may select t use TRANSACTION LOGGING nly during truble shting. If yu wish t use the Knwledge Base r cntact Custmer Supprt yu can : Frm within the xatm Manager r Prject Editr sftware, select the HELP icn r Visit www.ldi.cm and select Supprt. and then Online Supprt

eatm tmanager Release 2.5 Appendix B4 Stre & Frward (S&F) FAQ: When shuld I use it? And Hw big shuld I make my Size f queue and Time T Live? RESPONSE: Yu wuld typically use S&F with nn AUTOMATION endpints. It is recmmended fr any transactin that yu wuld like t stre n the mdule until its destinatin is nce again functining. Once available, the data is passed ut in a FIFO. An example f this types are the INSERT and UPDATE database cmmands. The Time T Live is the maximum length f time that a transactin will be saved in this S&F. After this time perid, the transactin will be deleted. Fr yur Size f queue, yu will need t allcate enugh space fr the strage f yur transactins during the Time T Live perid that yu have selected. If yu are nt sure, I recmmend use f the default values f (10M and INDEFINITE). Nte S&F size : 1. These files will be created when yu save (select OK). 2. Yu cannt mdify an endpint cnfiguratin in any way useless the endpint is STOPPED and this queue is empty. 3. I recmmend that yur stre and frward lg sizes be 10M r less. When larger sizes are selected, yu will see a slw respnse t its selectin f OK r APPLY with the larger sizes because this drive area is allcated t this purpse (i.e. S&F fr this endpint) when yu save this cnfiguratin. 4. Yu have mre than 2G available fr the strage f yur S&F and transactin lg n yur eatm appliance s cmpact flash; therefre, define yur S&F and Transactin lg sizes apprpriately. If yu wish t use the Knwledge Base r cntact Custmer Supprt yu can : Frm within the xatm Manager r Prject Editr sftware, select the HELP icn r Visit www.ldi.cm and select Supprt. and then Online Supprt

eatm tmanager Release 2.5 Appendix B5 Nte Handshake mde selectin impart f S&F : Stre&Frward is nly valid when used in cmbinatin with triggers with a HANDSHAKE MODE f IN QUEUE r RECEIVED FROM SOURCE; therefre, n message will be placed int S&F unless these handshaking mdes are selected fr yur message paths. This handshaking mde selectin is made n yur trigger edit screen. Autmatin EndPints FAQ : Why wuld I use multiple AUTOMATION ENDPOINTS? RESPONSE: There are several reasns. A few f these are listed belw. 1. Endpint STATUS TAG feedback, if used, is set at the AUTOMATION ENDPOINT level. This tag will reflect the status f the last transactin back t its plcs via this endpint. 2. TRANSACTION LOGGING: This lg is typically nt used fr Autmatin endpints. If yu wanted t lg the cmmunicatin between device and this appliance fr sme triggers and nt fr ther, yu wuld use multiple ENDPOINT. In mst cases, yu will wish t lg the ENTIRE MESSAGE r have n transactin lgging; hwever, the flexibility f selecting the # f bytes t lg per message is supprted. These lgs may be autmatically exprted as the file is full via FTP r SMTP. NOTE: Transactin lg Transactin lgging is seldm used with AUTOMATION ENDPOINTS. Its need riginated in the enterprise adapter wrld; hwever, it can be useful if truble shting cntrllers in the future. We recmmend that this features is nly used when it is needed then turned back ff t remve its verhead n the mdule. 3. Endpint handshaking fr FLOW CONTROL, if used, is set at the AUTOMATION ENDPOINT level. While typically nt used, yu wuld use this feature if yu wish t request data fr a database fr example, then hld it in the tmanager (i.e. the AUTOMATION adapter s STORE AND FORWARD) until the plc was ready t receive it. NOTE: Flw Cntrl FLOW CONTROL include cmpletin success and n errr feedback in its respnse. Yu have a REQUEST tag and a RESPONSE tag (DINT) If successful, RESPONSE == REQUEST value On errr, RESPONSE = negative f the REQUEST value Data is written t the plc when the REQUEST value set t a new value which is: Nn zer <10,000 nt equal t the current RESPONSE tag (i.e. the value f the request tag changed) If yu wish t use the Knwledge Base r cntact Custmer Supprt yu can : Frm within the xatm Manager r Prject Editr sftware, select the HELP icn r Visit www.ldi.cm and select Supprt. and then Online Supprt

eatm tmanager Release 2.5 Appendix C1 Appendix C: eatm tmanager Limits Cnfiguratin Sftware There is n limit t the number f UI systems installed, s yu can install the xatm Manager & Prject Editr sftware packages n as many systems as yu wish. Appliance Cnfiguratin The fllwing limits are enfrced n the appliance. These cunts are cumulative fr the entire appliance. Example: Fr MaxTriggers=Z, yu can have several prjects that cmbined have Z triggers r 1 prject with Z triggers. MaxPrjects = 8 MaxTriggers = 25 MaxMaps = 25 MaxPaths = 25 MaxAdapters = 16 Each adapter definitin fr a database, JMS, etc uses ne f these adapter cunts 1 adapter is related t each prject is autmatically allcated t Autmatin All PLCs are under this 1 adapter/prject Any adapter may be used in any cmbinatin allwed by yu license purchase. MaxEndpints = 25 MaxAutmatin = 32 Autmatin Adapter cntains an AUTOMATION TREE. Inside this tree, yu may nly be cnnected t a maximum f x cntrllers. Recmmend usage level maximum f 16 autmatin devices Tag/Variable Cunt Limit = n/a N enfrced tag limit during cnfiguratin NOTE: System Limit mdificatin If yur applicatin requires great numbers cntact OLDI supprt (supprt@ldi.cm) t discuss yur applicatin. If yu exceed any f these cnfiguratin cmpnent limits, yu will receive this errr message. This errr message is displayed when try create a new cmpnent after the maximum has been reached. If yu wish t use the Knwledge Base r cntact Custmer Supprt yu can : Frm within the xatm Manager r Prject Editr sftware, select the HELP icn r Visit www.ldi.cm and select Supprt. and then Online Supprt

eatm tmanager Release 2.5 Appendix D1 Appendix D: Functinality and Hierarchy f the Cnfiguratin Prgrams After the cnfiguratin sftware is installed, the cmputer s Start / All Prgrams menu will have a listing fr Online Develpment Inc / tmanager eatm and its tw cmpnents Prject Editr and xatm Manager. These tw cnfiguratin prgrams require that the eatm tmanager be nline when they are used. The xatm Manager sftware is used t cnfigure administrative items (netwrk settings, time zne, timesync, etc.) fr each eatm tmanager appliance. The Prject Editr sftware is used t cnfigure cnnectins and their transactins. A map f the menu system fr each f these prgrams is shwn belw. xatm Manager functinality: Administratin tab Status tab Netwrk tab Appliance name Ethernet prts Netwrk Diagnstics (PING,etc) Netwrking Rute Time Management tab Time zne/sync surce/manual System tab Appliance Backup/Restre Appliance Restart/Shutdwn Update tab Firmware Update Retrieve Supprt Infrmatin Reset t factry default License Management tab View/Update/RequestFile Cnfigure lgs tab General tab tab Lcatin / cntract / descriptin Appliance Versin/SerialNumber Users tab tab Define users and select their access level View individual appliance status System lg & Audit lg (View&Exprt) Prjects by name Endpints by name Right click t: Start/Stp Flush Messages Reset Failver Clear statistics Trigger & endpint statistics Requires Attentin/N Attentin Required flag View list f Attentin Required events Clearing flag Prjects tab Create/Delete Prject Editr functinality: Creatin f the cmpnents inside individual prjects Adapters AUTOMATION (PLC Cnnectin) Triggers Endpints Nn PLC adapter Endpints Triggers (Nn PLC&nn database) Maps (mapping surce t destinatin) Message Paths Schemas XML database clumn Tag Lists List fr variables fr each Autmatin endpint Request update Tables/Views Prcedures/Functins Database stred prcedures Applicatin Edit Status Exprt Crss reference Create NEW prjects, triggers, endpints,etc Switch prjects Imprt Schema Enumerate Schema (Autmatin) Mdule Cnnect/Exit (Discnnect) Start/Stp/Edit/Delete Cpy/Cut/Paste Search&Replace (tag names, etc) Prject Settings (Prject Status Tag) Lgs (mdule wide) View&Exprt System lg Audit lg Lgs (prject wide) If yu wish t use the Knwledge Base r cntact Custmer Supprt yu can : Frm within the xatm Manager r Prject Editr sftware, select the HELP icn r Visit www.ldi.cm and select Supprt. and then Online Supprt

eatm tmanager Release 2.5 xatm Manager functinality: Imprt/Exprt Cpy/Paste/Rename Start/Stp Edit (which starts Prject Editr) Appliance Brwser (Left panel) View Help Mnitr multiple eatm tmanager appliances n subnet NET : Define and scan subnets Cnnect t mdules Edit prjects (with Prject Editr) Appliance Brwser Full screen License agreement Cntext help Online supprt Abut this prgram Edit prjects (flder icn) Prject Editr functinality: View Appendix D2 View &Exprt Transactin lgs View Statistics Triggers statistics As well as the ability t by cmpnent Start/Stp/Open View its lg Reset statistics Endpints statistics As well as the ability t by cmpnent Start/Stp/Open View its lg Flush Messages Reset Failver Reset statistics Tag View (Autmatin variables read/write values) Help Appliance Brwser Full screen Clse panes Cntext help Online supprt Abut this prgram Manager appliance (Return t xatm MANAGER with cnnectin maintained t this eatm appliance) Attentin required (triangle with!) (Return t xatm MANAGER with cnnectin maintained t this eatm appliance) User t change user Appliance status Running/Halted & buttn t change status Prject status Running/Stpped & buttn t change status Plug icn status f PrjectEditr cnnect t tmanager (Green) and discnnect(red) & this buttn changes the status If yu wish t use the Knwledge Base r cntact Custmer Supprt yu can : Frm within the xatm Manager r Prject Editr sftware, select the HELP icn r Visit www.ldi.cm and select Supprt. and then Online Supprt

eatm tmanager Release 2.5 Appendix E1 Appendix E: Minimum System Requirements The eatm tmanager cnfiguratin applicatins require:.net 3.5 SP1 Windws 7 (32 bit r 64 bit mde) with ur applicatins running in 32 bit mde Or Windws XP Hme r Prfessinal, SP 2 r later Or Windws Server 2003 family with SP 1 r later Minimum Pentium 400MHz 1 GB RAM Recmmended: Pentium 1 GHz r higher, 2 GB r mre f RAM If yu wish t use the Knwledge Base r cntact Custmer Supprt yu can : Frm within the xatm Manager r Prject Editr sftware, select the HELP icn r Visit www.ldi.cm and select Supprt. and then Online Supprt