Brocade 5600 vrouter OSPFv3

14 September 2015 Brocade 5600 vrouter OSPFv3 Reference Guide Supporting Brocade 5600 vrouter 3.5R6

2015, Brocade Communications Systems, Inc. All Rights Reserved. ADX, Brocade, Brocade Assurance, the B-wing symbol, DCX, Fabric OS, HyperEdge, ICX, MLX, MyBrocade, OpenScript, The Effortless Network, VCS, VDX, Vplane, and Vyatta are registered trademarks, and Fabric Vision and vadx are trademarks of Brocade Communications Systems, Inc., in the United States and/or in other countries. Other brands, products, or service names mentioned may be trademarks of others. Notice: This document is for informational purposes only and does not set forth any warranty, expressed or implied, concerning any equipment, equipment feature, or service offered or to be offered by Brocade. Brocade reserves the right to make changes to this document at any time, without notice, and assumes no responsibility for its use. This informational document describes features that may not be currently available. Contact a Brocade sales office for information on feature and product availability. Export of technical data contained in this document may require an export license from the United States government. The authors and Brocade Communications Systems, Inc. assume no liability or responsibility to any person or entity with respect to the accuracy of this document or any loss, cost, liability, or damages arising from the information contained herein or the computer programs that accompany it. The product described by this document may contain open source software covered by the GNU General Public License or other open source license agreements. To find out which open source software is included in Brocade products, view the licensing terms applicable to the open source software, and obtain a copy of the programming source code, please visit http://www.brocade.com/support/oscd.

Contents Preface... 7 Document conventions...7 Text formatting conventions... 7 Command syntax conventions... 7 Notes, cautions, and warnings... 8 Brocade resources... 9 Contacting Brocade Technical Support...9 Document feedback... 10 About This Guide...11 OSPFv3 Configuration...13 OSPFv3 overview... 13 Support for OSPFv3 address families...14 Supported standard...14 Configuring OSPFv3... 14 Basic OSPFv3 configuration... 15 Verifying the OSPFv3 configuration... 17 OSPFv3 Commands... 21 monitor protocol ospfv3 background... 24 monitor protocol ospfv3 disable events...25 monitor protocol ospfv3 disable ifsm...26 monitor protocol ospfv3 disable lsa...27 monitor protocol ospfv3 disable nfsm...28 monitor protocol ospfv3 disable nsm...29 monitor protocol ospfv3 disable packet all... 30 monitor protocol ospfv3 disable packet dd...31 monitor protocol ospfv3 disable packet detail... 32 monitor protocol ospfv3 disable packet hello... 33 monitor protocol ospfv3 disable packet ls-ack... 34 monitor protocol ospfv3 disable packet ls-request... 35 monitor protocol ospfv3 disable packet ls-update... 36 monitor protocol ospfv3 disable packet recv... 37 monitor protocol ospfv3 disable packet send... 38 monitor protocol ospfv3 disable route... 39 monitor protocol ospfv3 enable events... 40 monitor protocol ospfv3 enable ifsm... 41 monitor protocol ospfv3 enable lsa... 42 monitor protocol ospfv3 enable nfsm... 43 monitor protocol ospfv3 enable nsm... 44 monitor protocol ospfv3 enable packet all...45 monitor protocol ospfv3 enable packet dd... 46 monitor protocol ospfv3 enable packet detail...47 monitor protocol ospfv3 enable packet hello...48 monitor protocol ospfv3 enable packet ls-ack... 49 monitor protocol ospfv3 enable packet ls-request...50 Brocade 5600 vrouter OSPFv3 Reference Guide 3

monitor protocol ospfv3 enable packet ls-update... 51 monitor protocol ospfv3 enable packet recv... 52 monitor protocol ospfv3 enable packet send... 53 monitor protocol ospfv3 enable route...54 protocols ospfv3 abr-type...55 protocols ospfv3 auto-cost reference-bandwidth <bandwidth>...56 protocols ospfv3 default-information originate... 57 protocols ospfv3 default-metric <metric>... 59 protocols ospfv3 distance...60 protocols ospfv3 distribute-list <name>... 62 protocols ospfv3 log... 63 protocols ospfv3 log events...64 protocols ospfv3 log ifsm...65 protocols ospfv3 log lsa...66 protocols ospfv3 log nfsm... 67 protocols ospfv3 log nsm... 68 protocols ospfv3 log packet...69 protocols ospfv3 log rib... 70 protocols ospfv3 log route...71 protocols ospfv3 passive-interface...72 protocols ospfv3 passive-interface-exclude... 73 protocols ospfv3 process <process-id> address-family ipv4 unicast... 74 protocols ospfv3 process <process-id> address-family ipv4 unicast area <area-id> range...76 protocols ospfv3 process <process-id> address-family ipv4 unicast default-information originate...78 protocols ospfv3 process <process-id> address-family ipv4 unicast redistribute...80 protocols ospfv3 process <process-id> address-family ipv4 unicast redistribute bgp...82 protocols ospfv3 process <process-id> address-family ipv4 unicast redistribute connected... 84 protocols ospfv3 process <process-id> address-family ipv4 unicast redistribute kernel...86 protocols ospfv3 process <process-id> address-family ipv4 unicast redistribute rip...88 protocols ospfv3 process <process-id> address-family ipv4 unicast redistribute static... 90 protocols ospfv3 process <process-id> address-family ipv4 unicast summary-address...92 protocols ospfv3 process <process-id> passive-interface-exclude...94 protocols ospfv3 redistribute bgp... 95 protocols ospfv3 redistribute connected... 96 protocols ospfv3 redistribute kernel... 97 protocols ospfv3 redistribute rip... 98 protocols ospfv3 redistribute static...99 protocols ospfv3 router-id <router-id>...100 protocols ospfv3 summary-address... 101 show ipv6 ospfv3...103 show ipv6 ospfv3 database...104 show ipv6 ospfv3 database adv-router... 106 show ipv6 ospfv3 database external...107 show ipv6 ospfv3 database grace...108 show ipv6 ospfv3 database inter-prefix...109 show ipv6 ospfv3 database inter-router... 110 show ipv6 ospfv3 database intra-prefix...111 show ipv6 ospfv3 database link... 112 show ipv6 ospfv3 database max-age...113 4 Brocade 5600 vrouter OSPFv3 Reference Guide

show ipv6 ospfv3 database network... 114 show ipv6 ospfv3 database nssa-external... 115 show ipv6 ospfv3 database router... 116 show ipv6 ospfv3 database self-originate... 117 show ipv6 ospfv3 interface...118 show ipv6 ospfv3 neighbor...119 show ipv6 ospfv3 route... 120 show ipv6 ospfv3 topology... 121 show ipv6 ospfv3 virtual-links...122 show ipv6 route ospfv3... 123 show monitoring protocols ospfv3...124 OSPFv3 Area Commands... 125 protocols ospfv3 area <area-id>... 126 protocols ospfv3 area <area-id> nssa...127 protocols ospfv3 area <area-id> nssa default-cost... 128 protocols ospfv3 area <area-id> nssa default-information-originate... 129 protocols ospfv3 area <area-id> nssa default-information-originate metric.. 130 protocols ospfv3 area <area-id> nssa default-information-originate metric-type...131 protocols ospfv3 area <area-id> nssa no-redistribution... 132 protocols ospfv3 area <area-id> nssa no-summary...133 protocols ospfv3 area <area-id> nssa stability-interval... 134 protocols ospfv3 area <area-id> nssa translator-role...135 protocols ospfv3 area <area-id> range... 136 protocols ospfv3 area <area-id> stub...138 protocols ospfv3 area <area-id> virtual-link <router-id>...139 protocols ospfv3 area <area-id> virtual-link <router-id> dead-interval <interval>...140 protocols ospfv3 area <area-id> virtual-link <router-id> hello-interval <interval>...142 protocols ospfv3 area <area-id> virtual-link <router-id> retransmitinterval <interval>... 143 protocols ospfv3 area <area-id> virtual-link <router-id> transmit-delay <delay>...144 OSPFv3 Interface Commands...147 interfaces <interface> ipv6 ospfv3... 148 interfaces <interface> ipv6 ospfv3 cost <cost>... 149 interfaces <interface> ipv6 ospfv3 dead-interval <interval>...151 interfaces <interface> ipv6 ospfv3 hello-interval <interval>... 152 interfaces <interface> ipv6 ospfv3 link-lsa-suppression enable...153 interfaces <interface> ipv6 ospfv3 mtu-ignore... 154 interfaces <interface> ipv6 ospfv3 neighbor... 155 interfaces <interface> ipv6 ospfv3 network <type>...156 interfaces <interface> ipv6 ospfv3 priority <priority>...157 interfaces <interface> ipv6 ospfv3 retransmit-interval <interval>...158 interfaces <interface> ipv6 ospfv3 transmit-delay <delay>... 160 Supported Interface Types...163 List of Acronyms...165 Brocade 5600 vrouter OSPFv3 Reference Guide 5

6 Brocade 5600 vrouter OSPFv3 Reference Guide

Preface Document conventions...7 Brocade resources... 9 Contacting Brocade Technical Support...9 Document feedback... 10 Document conventions The document conventions describe text formatting conventions, command syntax conventions, and important notice formats used in Brocade technical documentation. Text formatting conventions Text formatting conventions such as boldface, italic, or Courier font may be used in the flow of the text to highlight specific words or phrases. Format bold text italic text Courier font Description Identifies command names Identifies keywords and operands Identifies the names of user-manipulated GUI elements Identifies text to enter at the GUI Identifies emphasis Identifies variables Identifies document titles Identifies CLI output Identifies command syntax examples Command syntax conventions Bold and italic text identify command syntax components. Delimiters and operators define groupings of parameters and their logical relationships. Convention bold text italic text value Description Identifies command names, keywords, and command options. Identifies a variable. In Fibre Channel products, a fixed value provided as input to a command option is printed in plain text, for example, --show WWN. Brocade 5600 vrouter OSPFv3 Reference Guide 7

Notes, cautions, and warnings Convention Description [ ] Syntax components displayed within square brackets are optional. Default responses to system prompts are enclosed in square brackets. { x y z A choice of required parameters is enclosed in curly brackets separated by vertical bars. You must select one of the options. In Fibre Channel products, square brackets may be used instead for this purpose. x y A vertical bar separates mutually exclusive elements. < > Nonprinting characters, for example, passwords, are enclosed in angle brackets.... Repeat the previous element, for example, member[member...]. \ Indicates a soft line break in command examples. If a backslash separates two lines of a command input, enter the entire command at the prompt without the backslash. Notes, cautions, and warnings Notes, cautions, and warning statements may be used in this document. They are listed in the order of increasing severity of potential hazards. NOTE A Note provides a tip, guidance, or advice, emphasizes important information, or provides a reference to related information. ATTENTION An Attention statement indicates a stronger note, for example, to alert you when traffic might be interrupted or the device might reboot. CAUTION A Caution statement alerts you to situations that can be potentially hazardous to you or cause damage to hardware, firmware, software, or data. DANGER A Danger statement indicates conditions or situations that can be potentially lethal or extremely hazardous to you. Safety labels are also attached directly to products to warn of these conditions or situations. 8 Brocade 5600 vrouter OSPFv3 Reference Guide

Brocade resources Brocade resources Visit the Brocade website to locate related documentation for your product and additional Brocade resources. You can download additional publications supporting your product at www.brocade.com. Select the Brocade Products tab to locate your product, then click the Brocade product name or image to open the individual product page. The user manuals are available in the resources module at the bottom of the page under the Documentation category. To get up-to-the-minute information on Brocade products and resources, go to MyBrocade. You can register at no cost to obtain a user ID and password. Release notes are available on MyBrocade under Product Downloads. White papers, online demonstrations, and data sheets are available through the Brocade website. Contacting Brocade Technical Support As a Brocade customer, you can contact Brocade Technical Support 24x7 online, by telephone, or by e- mail. Brocade OEM customers contact their OEM/Solutions provider. Brocade customers For product support information and the latest information on contacting the Technical Assistance Center, go to http://www.brocade.com/services-support/index.html. If you have purchased Brocade product support directly from Brocade, use one of the following methods to contact the Brocade Technical Assistance Center 24x7. Online Telephone E-mail Preferred method of contact for nonurgent issues: My Cases through MyBrocade Software downloads and licensing tools Knowledge Base Required for Sev 1-Critical and Sev 2-High issues: Continental US: 1-800-752-8061 Europe, Middle East, Africa, and Asia Pacific: +800-AT FIBREE (+800 28 34 27 33) For areas unable to access toll free number: +1-408-333-6061 Toll-free numbers are available in many countries. support@brocade.com Please include: Problem summary Serial number Installation details Environment description Brocade OEM customers If you have purchased Brocade product support from a Brocade OEM/Solution Provider, contact your OEM/Solution Provider for all of your product support needs. OEM/Solution Providers are trained and certified by Brocade to support Brocade products. Brocade provides backline support for issues that cannot be resolved by the OEM/Solution Provider. Brocade 5600 vrouter OSPFv3 Reference Guide 9

Document feedback Brocade Supplemental Support augments your existing OEM support contract, providing direct access to Brocade expertise. For more information, contact Brocade or your OEM. For questions regarding service levels and response times, contact your OEM/Solution Provider. Document feedback To send feedback and report errors in the documentation you can use the feedback form posted with the document or you can e-mail the documentation team. Quality is our first concern at Brocade and we have made every effort to ensure the accuracy and completeness of this document. However, if you find an error or an omission, or you think that a topic needs further development, we want to hear from you. You can provide feedback in two ways: Through the online feedback form in the HTML documents posted on www.brocade.com. By sending your feedback to documentation@brocade.com. Provide the publication title, part number, and as much detail as possible, including the topic heading and page number if applicable, as well as your suggestions for improvement. 10 Brocade 5600 vrouter OSPFv3 Reference Guide

About This Guide This guide describes how to configure OSPFv3 on the Brocade vrouter (referred to as a virtual router, vrouter, or router in the guide). Brocade 5600 vrouter OSPFv3 Reference Guide 11

About This Guide 12 Brocade 5600 vrouter OSPFv3 Reference Guide

OSPFv3 Configuration OSPFv3 overview... 13 Support for OSPFv3 address families...14 Supported standard...14 Configuring OSPFv3... 14 OSPFv3 overview Open Shortest Path First Version 3 (OSPFv3) is a link-state Interior Gateway Protocol (IGP) developed by IETF and is based on OSPF Version 2 (OSPFv2), which supports IPv4. For more information about OSPFv2, refer to Brocade 5600 vrouter OSPF Reference Guide. OSPFv3 adds support for IPv6 in the OSPF routing protocol and is described in RFC 5340. OSPFv3 works as in OSPFv2, that is, OSPFv3 router IDs, area IDs, and LSA link-state IDs are 32 bits as in OSPFv2 IPv4. In addition, all optional capabilities of OSPFv2 for IPv4, for example, NSSA, are supported in OSPFv3 for IPv6. However, some significant changes exist in OSPFv3 for IPv6 and these changes include the following: Router LSAs and network LSAs no longer carry prefix information. In OSPFv3, these LSAs carry only the topology information. New and modified LSAs have been created to handle the flow of IPv6 addresses and prefixes in an OSPFv3 network. OSPFv3 runs on a per-link basis, instead of a per-ip-subnet basis. Two nodes can communicate over a link even when they do not share a common IPv6 prefix. Multiple OSPFv3 instances can run over the same link. OSPFv3 supports stub areas. IPv6 link-local addresses are used for OSPFv3 neighbor exchanges, except over virtual links. Linklocal addresses have local significance only. The 32-bit router ID in OSPFv3 always identifies neighboring routers. The flooding scope for LSAs is generalized into three categories for OSPFv3: Link-local scope. The OSPFv3 packet is flooded only to the members connected on a link. Area scope. The OSPFv3 packet is flooded to all members of an OSPFv3 area. AS scope. The OSPFv3 packet is flooded to all members of an AS. Authentication is removed from the OSPFv3 protocol. Instead, OSPFv3 relies on the AH and ESP portions of the IPSec for all authentication tasks in IPv6. LSPs and traffic engineering are not supported in OSPFv3. In OSPFv3, the Options field is available in only Hello packets, DD packets, Router LSAs, Network LSAs, Inter-Area-Router LSAs, and Link LSAs. OSPFv3 has two new LSAs: Link LSA and Intra Area Prefix LSA. OSPFv3 communicates over IPv6, but can carry routing data for other address families, most notably IPv4. OSPFv3 adds support for address families which helps OSPFv3 IPv6 networks to support both IPv6 and IPv4 nodes. For more information on this feature, refer to Support for OSPFv3 address families on page 14. Brocade 5600 vrouter OSPFv3 Reference Guide 13

Support for OSPFv3 address families Support for OSPFv3 address families OSPFv3 communicates with peer routers over IPv6, but can carry routing data for other address families. By default, OSPFv3 supports the IPv6 unicast address family. However, OSPFv3 can support other address families when configured to do so. The Brocade 5600 vrouter OSPFv3 implementation provides support for carrying IPv4 and IPv6 unicast routing data. It is important to understand that instance identifiers not only identify a routing instance, but also identify an address family. The following are the instance IDs breakdown: Instance ID 0 to 31: IPv6 unicast AF Instance ID 32 to 63: IPv6 multicast AF Instance ID 64 to 95: IPv4 unicast AF Instance ID 96 to 127: IPv4 multicast AF OSPFv3 supports multiple OSPFv3 processes and each process may support one address family. Multiple routing instances within each OSPFv3 process are also supported. Supported standard The Brocade Communications Systems, Inc. implementation of OSPFv3 complies with the following standards: RFC 5340: OSPF for IPv6 RFC 5838: Support of Address Families in OSPFv3 Configuring OSPFv3 This section provides the following topics: Basic OSPFv3 configuration on page 15 Verifying the OSPFv3 configuration on page 17 This section presents a sample configuration for OSPFv3. The configuration example is based on the following reference diagram. 14 Brocade 5600 vrouter OSPFv3 Reference Guide

Basic OSPFv3 configuration FIGURE 1 OSPFv3 configuration reference diagram Basic OSPFv3 configuration In this section, you configure OSPFv3 on the routers labeled R1 and R2 in the reference network diagram. To create a basic OSPFv3 configuration, perform the following steps in configuration mode: TABLE 1 Basic OSPFv3 configuration Router Step Command(s) Configure Interface IP addresses and OSPFv3 Configuration R1 R1 R1 R1 R1 Set an IPv6 address on interface dp0p1p2. Set an IPv6 address on interface dp0p1p3. Set the OSPFv3 area on interface dp0p1p2. Set the OSPFv3 area on interface dp0p1p3. Set the OSPFv3 area for a given process ID and instance ID on interface dp0p1p2. vyatta@r1# set interfaces dataplane dp0p1p2 address 2001:db8:0:4::1/64 vyatta@r1# set interfaces dataplane dp0p1p3 address 2001:db8:0:8::1/64 vyatta@r1# set interfaces dataplane dp0p1p2 ipv6 ospfv3 area 0.0.0.0 vyatta@r1# set interfaces dataplane dp0p1p3 ipv6 ospfv3 area 0.0.0.0 vyatta@r1# set interfaces dataplane dp0p1p2 ipv6 ospfv3 process labr instance-id 3 area 0.0.0.0 R1 Set the OSPFv3 area for a given process ID and instance ID on interface dp0p1p3. vyatta@r1# set interfaces dataplane dp0p1p3 ipv6 ospfv3 process labr instance-id 3 area 0.0.0.0 Brocade 5600 vrouter OSPFv3 Reference Guide 15

OSPFv3 Configuration TABLE 1 Basic OSPFv3 configuration (Continued) R1 Display the configuration. vyatta@r1# show interfaces dataplane dp0p1p2 { address 2001:db8:0:4::1/64 duplex auto hw-id 00:0c:29:09:3e:73 ipv6 { dup-addr-detect-transmits 1 ospfv3 { area 0.0.0.0 process labr { instance-id 3 { area 0.0.0.0 dataplane dp0p1p3 { address 2001:db8:0:8::1/64 duplex auto hw-id 00:0c:29:09:3e:7d ipv6 { dup-addr-detect-transmits 1 ospfv3 { area 0.0.0.0 process labr { instance-id 3 { area 0.0.0.0 Configure OSPFv3 Protocol Commands R1 R1 R1 R1 Specify the OSPFv3 address range and advertise this range. Set the global router ID for OSPFv3. Commit the configuration. Display the configuration. vyatta@r1# set protocols ospfv3 process labr area 0.0.0.0 range 2001::1/128 advertise vyatta@r1# set protocols ospfv3 process labr router-id 10.10.10.10 vyatta@r1# commit vyatta@r1# show protocols ospfv3 { process labr { area 0.0.0.0 { router-id 10.10.10.10 Configure Interface IP Addresses and OSPFv3 Configuration R2 R2 R2 Set an IPv6 address on interface dp0p1p2. Set an IPv6 address on interface dp0p1p3. Set the OSPFv3 area on interface dp0p1p2. vyatta@r2# set interfaces dataplane dp0p1p2 address 2001:db8:0:4::2/64 vyatta@r2# set interfaces dataplane dp0p1p3 address 2001:db8:0:200::/64 vyatta@r2# set interfaces dataplane dp0p1p2 ipv6 ospfv3 area 0.0.0.0 16 Brocade 5600 vrouter OSPFv3 Reference Guide

Verifying the OSPFv3 configuration TABLE 1 Basic OSPFv3 configuration (Continued) R2 Set the OSPFv3 area for a given process ID and instance ID on interface dp0p1p2. vyatta@r2# set interfaces dataplane dp0p1p2 ipv6 ospfv3 process labr instance-id 3 area 0.0.0.0 R2 Display the interface configuration. vyatta@r2# show interfaces dataplane dp0p1p2 { address 2001:db8:0:4::2/64 duplex auto hw-id 00:0c:29:4b:d8:ff ipv6 { dup-addr-detect-transmits 1 ospfv3 { area 0.0.0.0 process labr { instance-id 3 { area 0.0.0.0 dataplane dp0p1p3 { address 2001:db8:0:200::/64 duplex auto hw-id 00:0c:29:4b:d8:09 speed auto Configure OSPFv3 Protocol Commands R2 R2 R2 R2 Specify the OSPFv3 address range and advertise this range. Set the global OSPFv3 parameter of a router ID. Commit the configuration. Display the configuration. vyatta@r2# set protocols ospfv3 process labr area 0.0.0.0 range 2001::2/128 advertise vyatta@r2# set protocols ospfv3 process labr router-id 10.10.10.11 vyatta@r2# commit vyatta@r2# show protocols ospfv3 { process labr { area 0.0.0.0 { range 2001::2/128 { advertise router-id 10.10.10.11 Verifying the OSPFv3 configuration The following operational mode commands can be used to verify the OSPFv3 configuration. R1: show ipv6 ospfv3 neighbor The following example shows the output of the show ipv6 ospfv3 neighbor command for router R1. Brocade 5600 vrouter OSPFv3 Reference Guide 17

R1: show ipv6 route Verifying OSPFv3 on R1: "show ipv6 ospfv3 neighbor vyatta@r1:~$ show ipv6 ospfv3 neighbor OSPFv3 Process (labr) Neighbor ID Pri State Dead Time Interface Instance ID 10.10.10.11 1 Full/DR 00:00:34 dp0p1p2 3 R1: show ipv6 route The following example shows the output of the show ipv6 route command for router R1. Verifying OSPFv3 on R1: show ipv6 route vyatta@r1:~$ show ipv6 route IPv6 Routing Table Codes: K - kernel route, C - connected, S - static, R - RIP, O - OSPF, IA - OSPF inter area, E1 - OSPF external type 1, E2 - OSPF external type 2, I - IS-IS, B - BGP > - selected route, * - FIB route, p - stale info Timers: Uptime C *> ::1/128 is directly connected, lo O 2001:db8:0:4::/64 [110/1] is directly connected, dp0p1p2, 23:39:41 C *> 2001:db8:0:4::/64 is directly connected, dp0p1p2 O 2001:db8:0:8::/64 [110/1] is directly connected, dp0p1p3, 23:39:41 C *> 2001:db8:0:8::/64 is directly connected, dp0p1p3 C * fe80::/64 is directly connected, dp0p1p2 C * fe80::/64 is directly connected, dp0p1p1 C *> fe80::/64 is directly connected, dp0p1p3 K *> ff00::/8 is directly connected, dp0p1p2 K * ff00::/8 is directly connected, dp0p1p1 K * ff00::/8 is directly connected, dp0p1p3 R2: show ipv6 ospfv3 neighbor The following example shows the output of the show ipv6 ospfv3 neighbor command for router R2. Verifying OSPFv3 on R2: show ipv6 ospfv3 neighbor vyatta@r2:~$ show ipv6 ospfv3 neighbor OSPFv3 Process (labr) Neighbor ID Pri State Dead Time Interface Instance ID 10.10.10.10 1 Full/Backup 00:00:36 dp0p1p2 3 R2: show ipv6 route The following example shows the output of the show ipv6 route command for router R2. Verifying OSPFv3 on R2: show ipv6 route vyatta@r2:~$ show ipv6 route IPv6 Routing Table Codes: K - kernel route, C - connected, S - static, R - RIP, O - OSPF, IA - OSPF inter area, E1 - OSPF external type 1, E2 - OSPF external type 2, I - IS-IS, B - BGP > - selected route, * - FIB route, p - stale info Timers: Uptime C *> ::1/128 is directly connected, lo O 2001:db8:0:4::/64 [110/1] is directly connected, dp0p1p2, 23:44:53 C *> 2001:db8:0:4::/64 is directly connected, dp0p1p2 O *> 2001:db8:0:8::/64 [110/2] via fe80::20c:29ff:fe09:3e73, dp0p1p2, 23:44:02 18 Brocade 5600 vrouter OSPFv3 Reference Guide

R2: ping 2001:db8:0:8::1 C C C C C K K K *> 2001:db8:0:200::/64 is directly connected, dp0p1p3 *> 2004::/64 is directly connected, lo * fe80::/64 is directly connected, dp0p1p2 * fe80::/64 is directly connected, dp0p1p1 *> fe80::/64 is directly connected, dp0p1p3 *> ff00::/8 is directly connected, dp0p1p2 * ff00::/8 is directly connected, dp0p1p1 * ff00::/8 is directly connected, dp0p1p3 R2: ping 2001:db8:0:8::1 Using the ping command from R2, we can verify that we can reach hosts on remote networks. In this case we ping an IP address on R1. This verification is shown in the following example. Verifying OSPF on R2: ping6 2001:db8:0:8::1 vyatta@r2# ping6 2001:db8:0:8::1 PING 2001:db8:0:8::1(2001:db8:0:8::1) 56 data bytes 64 bytes from 2001:db8:0:8::1: icmp_seq=1 ttl=64 time=0.460 ms 64 bytes from 2001:db8:0:8::1: icmp_seq=2 ttl=64 time=0.153 ms 64 bytes from 2001:db8:0:8::1: icmp_seq=3 ttl=64 time=0.209 ms 64 bytes from 2001:db8:0:8::1: icmp_seq=4 ttl=64 time=0.156 ms 64 bytes from 2001:db8:0:8::1: icmp_seq=5 ttl=64 time=0.163 ms 64 bytes from 2001:db8:0:8::1: icmp_seq=6 ttl=64 time=0.159 ms --- 2001:db8:0:8::1 ping statistics --- 6 packets transmitted, 6 received, 0% packet loss, time 4997ms rtt min/avg/max/mdev = 0.153/0.216/0.460/0.111 ms The output confirms that the OSPFv3 configuration is working and that we are able to reach a remote network. Brocade 5600 vrouter OSPFv3 Reference Guide 19

R2: ping 2001:db8:0:8::1 20 Brocade 5600 vrouter OSPFv3 Reference Guide

OSPFv3 Commands monitor protocol ospfv3 background... 24 monitor protocol ospfv3 disable events...25 monitor protocol ospfv3 disable ifsm...26 monitor protocol ospfv3 disable lsa...27 monitor protocol ospfv3 disable nfsm...28 monitor protocol ospfv3 disable nsm...29 monitor protocol ospfv3 disable packet all... 30 monitor protocol ospfv3 disable packet dd...31 monitor protocol ospfv3 disable packet detail... 32 monitor protocol ospfv3 disable packet hello... 33 monitor protocol ospfv3 disable packet ls-ack... 34 monitor protocol ospfv3 disable packet ls-request... 35 monitor protocol ospfv3 disable packet ls-update... 36 monitor protocol ospfv3 disable packet recv... 37 monitor protocol ospfv3 disable packet send... 38 monitor protocol ospfv3 disable route... 39 monitor protocol ospfv3 enable events... 40 monitor protocol ospfv3 enable ifsm... 41 monitor protocol ospfv3 enable lsa... 42 monitor protocol ospfv3 enable nfsm... 43 monitor protocol ospfv3 enable nsm... 44 monitor protocol ospfv3 enable packet all...45 monitor protocol ospfv3 enable packet dd... 46 monitor protocol ospfv3 enable packet detail...47 monitor protocol ospfv3 enable packet hello...48 monitor protocol ospfv3 enable packet ls-ack... 49 monitor protocol ospfv3 enable packet ls-request...50 monitor protocol ospfv3 enable packet ls-update...51 monitor protocol ospfv3 enable packet recv...52 monitor protocol ospfv3 enable packet send...53 monitor protocol ospfv3 enable route...54 protocols ospfv3 abr-type...55 protocols ospfv3 auto-cost reference-bandwidth <bandwidth>...56 protocols ospfv3 default-information originate... 57 protocols ospfv3 default-metric <metric>... 59 protocols ospfv3 distance...60 protocols ospfv3 distribute-list <name>...62 protocols ospfv3 log... 63 protocols ospfv3 log events...64 protocols ospfv3 log ifsm...65 protocols ospfv3 log lsa...66 protocols ospfv3 log nfsm... 67 protocols ospfv3 log nsm... 68 Brocade 5600 vrouter OSPFv3 Reference Guide 21

OSPFv3 Commands protocols ospfv3 log packet...69 protocols ospfv3 log rib... 70 protocols ospfv3 log route...71 protocols ospfv3 passive-interface...72 protocols ospfv3 passive-interface-exclude... 73 protocols ospfv3 process <process-id> address-family ipv4 unicast... 74 protocols ospfv3 process <process-id> address-family ipv4 unicast area <areaid> range...76 protocols ospfv3 process <process-id> address-family ipv4 unicast defaultinformation originate... 78 protocols ospfv3 process <process-id> address-family ipv4 unicast redistribute... 80 protocols ospfv3 process <process-id> address-family ipv4 unicast redistribute bgp...82 protocols ospfv3 process <process-id> address-family ipv4 unicast redistribute connected... 84 protocols ospfv3 process <process-id> address-family ipv4 unicast redistribute kernel...86 protocols ospfv3 process <process-id> address-family ipv4 unicast redistribute rip... 88 protocols ospfv3 process <process-id> address-family ipv4 unicast redistribute static... 90 protocols ospfv3 process <process-id> address-family ipv4 unicast summaryaddress...92 protocols ospfv3 process <process-id> passive-interface-exclude...94 protocols ospfv3 redistribute bgp... 95 protocols ospfv3 redistribute connected...96 protocols ospfv3 redistribute kernel... 97 protocols ospfv3 redistribute rip... 98 protocols ospfv3 redistribute static...99 protocols ospfv3 router-id <router-id>...100 protocols ospfv3 summary-address... 101 show ipv6 ospfv3...103 show ipv6 ospfv3 database...104 show ipv6 ospfv3 database adv-router... 106 show ipv6 ospfv3 database external...107 show ipv6 ospfv3 database grace...108 show ipv6 ospfv3 database inter-prefix...109 show ipv6 ospfv3 database inter-router... 110 show ipv6 ospfv3 database intra-prefix...111 show ipv6 ospfv3 database link... 112 show ipv6 ospfv3 database max-age...113 show ipv6 ospfv3 database network... 114 show ipv6 ospfv3 database nssa-external... 115 show ipv6 ospfv3 database router... 116 show ipv6 ospfv3 database self-originate... 117 show ipv6 ospfv3 interface...118 show ipv6 ospfv3 neighbor...119 show ipv6 ospfv3 route... 120 show ipv6 ospfv3 topology...121 22 Brocade 5600 vrouter OSPFv3 Reference Guide

OSPFv3 Commands show ipv6 ospfv3 virtual-links...122 show ipv6 route ospfv3... 123 show monitoring protocols ospfv3...124 Brocade 5600 vrouter OSPFv3 Reference Guide 23

monitor protocol ospfv3 background monitor protocol ospfv3 background Starts and stops background monitoring of OSPFv3 packets. Syntax monitor protocol ospfv3 background { start stop start stop Operational mode Starts background monitoring of OSPFv3 packets. Stops background monitoring of OSPFv3 packets. Use this command to start and stop background monitoring of OSPFv3 packets. 24 Brocade 5600 vrouter OSPFv3 Reference Guide

monitor protocol ospfv3 disable events monitor protocol ospfv3 disable events Disables the generation of debug messages related to OSPFv3 events. Syntax monitor protocol ospfv3 disable events [ abr asbr nssa os router vlink ] Command Default OSPFv3 event debugging is disabled. abr asbr nssa os router vlink Operational mode Disables debugging of Area Border Router (ABR) events. Disables debugging of Autonomous System Boundary Router (ASBR) events. Disables debugging of not-so-stubby area (NSSA) events. Disables debugging of OS-interaction events. Disables debugging of other router events. Disables debugging of virtual-link events. Use this command to disable the generation of debug messages related to OSPFv3 events. Brocade 5600 vrouter OSPFv3 Reference Guide 25

monitor protocol ospfv3 disable ifsm monitor protocol ospfv3 disable ifsm Disables the generation of debug messages related to OSPFv3 Interface Finite State Machine (IFSM) events. Syntax monitor protocol ospfv3 disable ifsm [ events status timers ] Command Default OSPFv3 IFSM event debugging is disabled. events status timers Operational mode Disables debugging of IFSM events. Disables debugging of IFSM status information. Disables debugging of IFSM timer information. Use this command to disable the generation of debug messages related to OSPFv3 IFSM events. 26 Brocade 5600 vrouter OSPFv3 Reference Guide

monitor protocol ospfv3 disable lsa monitor protocol ospfv3 disable lsa Disables the generation of debug messages related to OSPFv3 Link State Advertisements (LSAs). Syntax monitor protocol ospfv3 disable lsa [ flooding generate install maxage refresh ] Command Default OSPFv3 LSA event debugging is disabled. flooding generate install maxage refresh Operational mode Disables debugging of OSPFv3 LSA flood events. Disables debugging of OSPFv3 LSA generation. Disables debugging of OSPFv3 LSA installation. Disables debugging of maximum age processing related OSPFv3 LSA. Disables debugging of OSPFv3 LSA refreshes. Use this command to disable the generation of debug messages related to OSPFv3 LSAs. Brocade 5600 vrouter OSPFv3 Reference Guide 27

monitor protocol ospfv3 disable nfsm monitor protocol ospfv3 disable nfsm Disables the generation of debug messages related to OSPFv3 Neighbor Finite State Machines (NFSMs). Syntax monitor protocol ospfv3 disable nfsm [ events status timers ] Command Default OSPFv3 NFSM debugging is disabled. events status timers Operational mode Disables debugging of OSPFv3 NFSM events. Disables debugging of OSPFv3 NFSM status. Disables debugging of OSPFv3 NFSM timers. Use this command to disable the generation of debug messages related to OSPFv3 NFSM. 28 Brocade 5600 vrouter OSPFv3 Reference Guide

monitor protocol ospfv3 disable nsm monitor protocol ospfv3 disable nsm Disables the generation of debug messages related to the OSPFv3 Network Services Module (NSM). Syntax monitor protocol ospfv3 disable nsm [ interface redistribute ] Command Default OSPFv3 NSM debugging is disabled. interface redistribute Operational mode Disables debugging of OSPFv3 NSM interface events. Disables debugging of OSPFv3 NSM redistribute events. Use this command to disable the generation of debug messages related to the OSPFv3 NSM. Brocade 5600 vrouter OSPFv3 Reference Guide 29

monitor protocol ospfv3 disable packet all monitor protocol ospfv3 disable packet all Disables the generation of debug messages related to all OSPFv3 packets that are arriving at and leaving a router. Syntax monitor protocol ospfv3 disable packet all [ detail recv [ detail ] send [ detail ] ] Command Default Debug messages are disabled for all OSPFv3 packets at a medium level of detail. detail recv detail send detail Operational mode Disables detailed debugging of all OSPFv3 packets, both sent and received. Disables debugging of all received OSPFv3 packets. Disables detailed debugging of all received OSPFv3 packets. Disables debugging of all transmitted OSPFv3 packets. Disables detailed debugging of all transmitted OSPFv3 packets. Use this command to disable the generation of debug messages related to all OSPFv3 packets that are arriving at and leaving a router. 30 Brocade 5600 vrouter OSPFv3 Reference Guide

monitor protocol ospfv3 disable packet dd monitor protocol ospfv3 disable packet dd Disables the generation of debug messages related to OSPFv3 Database Description (DD) packets. Syntax monitor protocol ospfv3 disable packet dd [ detail recv [ detail ] send [ detail ] ] Command Default Debug messages are disabled for OSPFv3 DD packets at a medium level of detail. detail recv detail send detail Operational mode Disables detailed debugging of OSPFv3 DD packets, both sent and received. Disables debugging of received OSPFv3 DD packets. Disables detailed debugging of received OSPFv3 DD packets. Disables debugging of transmitted OSPFv3 DD packets. Disables detailed debugging of transmitted OSPFv3 DD packets. Use this command to disable the generation of debug messages related to OSPFv3 DD packets. Brocade 5600 vrouter OSPFv3 Reference Guide 31

monitor protocol ospfv3 disable packet detail monitor protocol ospfv3 disable packet detail Disables the generation of debug messages related to OSPFv3 detailed packets. Syntax Command Default monitor protocol ospfv3 disable packet detail Debug messages are disabled for OSPFv3 detailed packets. Operational mode Use this command to disable the generation of debug messages related to OSPFv3 detailed packets. 32 Brocade 5600 vrouter OSPFv3 Reference Guide

monitor protocol ospfv3 disable packet hello monitor protocol ospfv3 disable packet hello Disables the generation of debug messages related to OSPFv3 Hello packets. Syntax monitor protocol ospfv3 disable packet hello [ detail recv [ detail ] send [ detail ] ] Command Default Debug messages are disabled for OSPFv3 Hello packets at a medium level of detail. detail recv detail send detail Operational mode Disables detailed debugging of OSPFv3 Hello packets, both sent and received. Disables debugging of received OSPFv3 Hello packets. Disables detailed debugging of received OSPFv3 Hello packets. Disables debugging of transmitted OSPFv3 Hello packets. Disables detailed debugging of transmitted OSPFv3 Hello packets. Use this command to disable the generation of debug messages related to OSPFv3 Hello packets. Brocade 5600 vrouter OSPFv3 Reference Guide 33

monitor protocol ospfv3 disable packet ls-ack monitor protocol ospfv3 disable packet ls-ack Disables the generation of debug messages related to OSPFv3 link-state acknowledgement (LS Ack) packets. Syntax monitor protocol ospfv3 disable packet ls-ack [ detail recv [ detail ] send [ detail ] ] Command Default Debug messages are disabled for OSPFv3 LS Ack packets at a medium level of detail. detail recv detail send detail Disables detailed debugging of OSPFv3 LS Ack packets, both sent and received. Disables debugging of received OSPFv3 LS Ack packets. Disables detailed debugging of received OSPFv3 LS Ack packets. Disables debugging of transmitted OSPFv3 LS Ack packets. Disables detailed debugging of transmitted OSPFv3 LS Ack packets. Operational mode Use this command to disable the generation of debug messages related to OSPFv3 LS Ack packets. 34 Brocade 5600 vrouter OSPFv3 Reference Guide

monitor protocol ospfv3 disable packet ls-request monitor protocol ospfv3 disable packet ls-request Disables the generation of debug messages related to OSPFv3 link-state request (LSR) packets. Syntax monitor protocol ospfv3 disable packet ls-request [ detail recv [ detail ] send [ detail ] ] Command Default Debug messages are disabled for OSPFv3 LSR packets at a medium level of detail. detail recv detail send detail Operational mode Disables detailed debugging of OSPFv3 LSR packets, both sent and received. Disables debugging of received OSPFv3 LSR packets. Disables detailed debugging of received OSPFv3 LSR packets. Disables debugging of transmitted OSPFv3 LSR packets. Disables detailed debugging of transmitted OSPFv3 LSR packets. Use this command to disable the generation of debug messages related to OSPFv3 LSR packets. Brocade 5600 vrouter OSPFv3 Reference Guide 35

monitor protocol ospfv3 disable packet ls-update monitor protocol ospfv3 disable packet ls-update Disables the generation of debug messages related to OSPFv3 link-state update (LSU) packets. Syntax monitor protocol ospfv3 disable packet ls-update [ detail recv [ detail ] send [ detail ] ] Command Default Debug messages are disabled for OSPFv3 LSU packets at a medium level of detail. detail recv detail send detail Operational mode Disables detailed debugging of OSPFv3 LSU packets, both sent and received. Disables debugging of received OSPFv3 LSU packets. Disables detailed debugging of received OSPFv3 LSU packets. Disables debugging of transmitted OSPFv3 LSU packets. Disables detailed debugging of transmitted OSPFv3 LSU packets. Use this command to disable the generation of debug messages related to OSPFv3 LSU packets. 36 Brocade 5600 vrouter OSPFv3 Reference Guide

monitor protocol ospfv3 disable packet recv monitor protocol ospfv3 disable packet recv Disables the generation of debug messages related to OSPFv3 received packets. Syntax Command Default monitor protocol ospfv3 disable packet recv Debug messages are disabled for OSPFv3 received packets. Operational mode Use this command to disable the generation of debug messages related to OSPFv3 received packets. Brocade 5600 vrouter OSPFv3 Reference Guide 37

monitor protocol ospfv3 disable packet send monitor protocol ospfv3 disable packet send Disables the generation of debug messages related to OSPFv3 sent packets. Syntax Command Default monitor protocol ospfv3 disable packet send Debug messages are disabled for OSPFv3 sent packets. Operational mode Use this command to disable the generation of debug messages related to OSPFv3 sent packets. 38 Brocade 5600 vrouter OSPFv3 Reference Guide

monitor protocol ospfv3 disable route monitor protocol ospfv3 disable route Disables the generation of debug messages related to OSPFv3 route calculations. Syntax monitor protocol ospfv3 disable route [ ase ia install spf ] Command Default Debug messages are disabled for OSPFv3 route calculations. ase ia install spf Operational mode Disables detailed debugging of OSPFv3 external route calculations. Disables detailed debugging of OSPFv3 inter-area route calculations. Disables detailed debugging of OSPFv3 route installation. Disables detailed debugging of OSPFv3 Shortest Path First (SPF) calculation. Use this command to disable the generation of debug messages related to OSPFv3 route calculations. Brocade 5600 vrouter OSPFv3 Reference Guide 39

monitor protocol ospfv3 enable events monitor protocol ospfv3 enable events Enables the generation of debug messages related to OSPFv3 events. Syntax monitor protocol ospfv3 enable events [ abr asbr nssa os router vlink ] abr asbr nssa os router vlink Operational mode Enables debugging of Area Border Router (ABR) events. Enables debugging of Autonomous System Boundary Router (ASBR) events. Enables debugging of not-so-stubby area (NSSA) events. Enables debugging of OS-interaction events. Enables debugging of other router events. Enables debugging of virtual-link events. Use this command to enable the generation of debug messages related to OSPFv3 events. 40 Brocade 5600 vrouter OSPFv3 Reference Guide

monitor protocol ospfv3 enable ifsm monitor protocol ospfv3 enable ifsm Enables the generation of debug messages related to OSPFv3 Interface Finite State Machine (IFSM) events. Syntax monitor protocol ospfv3 enable ifsm [ events status timers ] events status timers Operational mode Enables debugging of IFSM events. Enables debugging of IFSM status information. Enables debugging of IFSM timer information. Use this command to enable the generation of debug messages related to OSPFv3 IFSM events. Brocade 5600 vrouter OSPFv3 Reference Guide 41

monitor protocol ospfv3 enable lsa monitor protocol ospfv3 enable lsa Enables the generation of debug messages related to OSPFv3 Link State Advertisements (LSAs). Syntax monitor protocol ospfv3 enable lsa [ flooding generate install maxage refresh ] flooding generate install maxage refresh Operational mode Enables debugging of OSPFv3 LSA flood events. Enables debugging of OSPFv3 LSA generation. Enables debugging of OSPFv3 LSA installation. Enables debugging of maximum age processing related OSPFv3 LSA. Enables debugging of OSPFv3 LSA refreshes. Use this command to enable the generation of debug messages related to OSPFv3 LSAs. 42 Brocade 5600 vrouter OSPFv3 Reference Guide

monitor protocol ospfv3 enable nfsm monitor protocol ospfv3 enable nfsm Enables the generation of debug messages related to OSPFv3 Neighbor Finite State Machines (NFSMs). Syntax monitor protocol ospfv3 enable nfsm [ events status timers ] events status timers Operational mode Enables debugging of OSPFv3 NFSM events. Enables debugging of OSPFv3 NFSM status. Enables debugging of OSPFv3 NFSM timers. Use this command to enable the generation of debug messages related to OSPFv3 NFSM. Brocade 5600 vrouter OSPFv3 Reference Guide 43

monitor protocol ospfv3 enable nsm monitor protocol ospfv3 enable nsm Enables the generation of debug messages related to OSPFv3 Network Services Module (NSM). Syntax monitor protocol ospfv3 enable nsm [ interface redistribute ] interface redistribute Operational mode Enables debugging of OSPFv3 NSM interface events. Enables debugging of OSPFv3 NSM redistribute events. Use this command to enable the generation of debug messages related to OSPFv3 NSM. 44 Brocade 5600 vrouter OSPFv3 Reference Guide

monitor protocol ospfv3 enable packet all monitor protocol ospfv3 enable packet all Enables the generation of debug messages related to all OSPFv3 packets that are arriving at and leaving a router. Syntax monitor protocol ospfv3 enable packet all [ detail recv [ detail ] send [ detail ] ] Command Default Debug messages are enabled for all OSPFv3 packets at a medium level of detail. detail recv detail send detail Operational mode Enables detailed debugging of all OSPFv3 packets, both sent and received. Enables debugging of all received OSPFv3 packets. Enables detailed debugging of all received OSPFv3 packets. Enables debugging of all transmitted OSPFv3 packets. Enables debugging of all transmitted OSPFv3 packets. Use this command to enable the generation of debug messages related to all OSPFv3 packets that are arriving at and leaving a router. Brocade 5600 vrouter OSPFv3 Reference Guide 45

monitor protocol ospfv3 enable packet dd monitor protocol ospfv3 enable packet dd Enables the generation of debug messages related to OSPFv3 Database Description (DD) packets. Syntax monitor protocol ospfv3 enable packet dd [ detail recv [ detail ] send [ detail ] ] Command Default Debug messages are generated for OSPF DD packets at a medium level of detail. detail recv detail send detail Operational mode Enables detailed debugging of OSPFv3 DD packets, both sent and received. Enables debugging of received OSPFv3 DD packets. Enables detailed debugging of received OSPFv3 DD packets. Enables debugging of transmitted OSPFv3 DD packets. Enables detailed debugging of transmitted OSPFv3 DD packets. Use this command to enable the generation of debug messages related to OSPFv3 DD packets. 46 Brocade 5600 vrouter OSPFv3 Reference Guide

monitor protocol ospfv3 enable packet detail monitor protocol ospfv3 enable packet detail Enables the generation of debug messages related to OSPFv3 detailed packets. Syntax monitor protocol ospfv3 enable packet detail Operational mode Use this command to enable the generation of debug messages related to OSPFv3 detailed packets. Brocade 5600 vrouter OSPFv3 Reference Guide 47

monitor protocol ospfv3 enable packet hello monitor protocol ospfv3 enable packet hello Enables the generation of debug messages related to OSPFv3 Hello packets. Syntax monitor protocol ospfv3 enable packet hello [ detail recv [ detail ] send [ detail ] ] Command Default Debug messages are generated for OSPFv3 Hello packets at a medium level of detail. detail recv detail send detail Operational mode Enables detailed debugging of OSPFv3 Hello packets, both sent and received. Enables detailed debugging of received OSPFv3 Hello packets. Enables detailed debugging of received OSPFv3 Hello packets. Enables debugging of transmitted OSPFv3 Hello packets. Enables detailed debugging of transmitted OSPFv3 Hello packets. Use this command to enable the generation of debug messages related to OSPFv3 Hello packets. 48 Brocade 5600 vrouter OSPFv3 Reference Guide

monitor protocol ospfv3 enable packet ls-ack monitor protocol ospfv3 enable packet ls-ack Enables the generation of debug messages related to OSPFv3 link-state acknowledgment (LS Ack) packets. Syntax monitor protocol ospfv3 enable packet ls-ack [ detail recv [ detail ] send [ detail ] ] Command Default Debug messages are generated for OSPFv3 LS Ack packets at a medium level of detail. detail recv detail send detail Enables detailed debugging of OSPFv3 LS Ack packets, both sent and received. Enables debugging of received OSPFv3 LS Ack packets. Enables detailed debugging of received OSPFv3 LS Ack packets. Enables debugging of transmitted OSPFv3 LS Ack packets. Enables detailed debugging of transmitted OSPFv3 LS Ack packets. Operational mode Use this command to enable the generation of debug messages related to OSPFv3 LS Ack packets. Brocade 5600 vrouter OSPFv3 Reference Guide 49

monitor protocol ospfv3 enable packet ls-request monitor protocol ospfv3 enable packet ls-request Enables the generation of debug messages related to OSPFv3 link-state request (LSR) packets. Syntax monitor protocol ospfv3 enable packet ls-request [ detail recv [ detail ] send [ detail ] ] Command Default Debug messages are generated for OSPFv3 LSR packets at a medium level of detail. detail recv detail send detail Operational mode Enables detailed debugging of OSPFv3 LSR packets, both sent and received. Enables debugging of received OSPFv3 LSR packets. Enables detailed debugging of received OSPFv3 LSR packets. Enables debugging of transmitted OSPFv3 LSR packets. Enables detailed debugging of transmitted OSPFv3 LSR packets. Use this command to enable the generation of debug messages related to OSPFv3 LSR packets. 50 Brocade 5600 vrouter OSPFv3 Reference Guide