Telindus 2400 Series Features and benefits Small ADSL/SHDSL DSLAM for professional broadband services 1 unit high housing for compact central-office solution 8, 16 or 24 ADSL or SHDSL line pairs per unit with possibility for cascading Combines ATM switching, IP routing and VLAN switching in one device Suitable for flexible migration from Frame-Relay/ATM to IP transport Full IP QoS support Modular interface for maximum flexibility for backbone connectivity The Telindus 2400 Series enable service providers to deploy business services over ADSL and SHDSL, while maintaining a maximum flexibility for the connection to the backbone. Apart from a fixed 100Base-T backbone connection, the Telindus 2400 Series can accept various modular interfaces with support for PPP, Frame-Relay or ATM. These interfaces include 6x E1 with support for IMA (Inverse Multiplexing over ATM), multilink PPP or multilink Frame- Relay. The number of E1 lines and the encapsulation scheme effectively used can be selected by configuration (e.g. 4x E1 IMA) E3 with PPP, Frame-Relay or ATM STM1 with ATM 10/100 Ethernet interface with built-in 4 port switch The Telindus 2400 Operating System supports ATM switching, full IP-routing, bridging and VLAN switching. The unit can be split into multiple bridge groups, enabling direct mappings between DSL lines and VLANs. In addition is has an extended support for IP CoS (Class of Service) and it can initiate and terminate VPN (Virtual Private Network) circuits. Therefore, the Telindus 2400 Series can be used for supporting services like VoIP (Voice over IP) and intranet applications. The Telindus 2400 access concentrator houses 8, 16 or 24 ADSL or SHDSL modems. Two SHDSL circuits can also be combined to increase the distance or speed towards the end-users. The equipment can be used as desktop equipment or can be rack-mounted (19 or ETSI). Multiple units can be cascaded through the 100Base-T Ethernet interface. In case of IP routing, bridging or VLAN Telindus 2400 Series data sheet Version 2.0 30 January 2004 1 / 7
switching, several units can be interconnected via the fixed and modular Ethernet interfaces. On the last Telindus 2400 unit, the data is encapsulated for the WAN interface. In case of ATM switching, 2 units can be cascaded over Ethernet using a proprietary mechanism as shown on the figure. The unit comes with an extensive built-in management agent. The unit can be controlled locally by means of a craft terminal or can be managed remotely over IP. In this way the existing IP infrastructure can be used to transport all management information to a central location without the need for a separate overlay network. Typical applications include the rollout of business-oriented services over DSL as it is applicable in operator or campus network environments. Block diagram of the Telindus 2400 Series access concentrator As indicated in the diagram, by using the appropriate CPE at the end-user site, the Telindus 2400 Series can provide IP, VLAN, ATM, Circuit Emulation and Frame-Relay services based on SHDSL or ADSL transmission technology. Telindus 2400 simplified protocol diagram Telindus 2400 Series data sheet Version 2.0 30 January 2004 2 / 7
Technical specifications Versions Version # DSL ports Options Power supply TELINDUS 2401 ADSL 8 Annex A / annex B, built-in splitter -, AC TELINDUS 2402 ADSL 16 Annex A / annex B - TELINDUS 2403 ADSL 24 Annex A / annex B - TELINDUS 2421 SHDSL 8 -, AC TELINDUS 2422 SHDSL 16 - TELINDUS 2423 SHDSL 24 - ADSL Line interface Single-pair ADSL line access Coding: compliant to ITU-T G.992.1 (ADSL G.dmt), ITU-T G.992.2 (ADSL G.Lite), ETSI TS 101 388 v1.3.1, ITU-T G.992.3 (ADSL2 G.dmt)* and ITU-T G.992.4 (ADSL2 G.Lite)* Support for ITU-T annex A (POTS) or Annex B (ISDN and POTS) Optional integrated POTS or ISDN splitters (on 2401 versions) Connector: 50 pin telco connector Line speeds: Downstream: 32 kbps up to 12* Mbps Upstream: 32 kbps up to 1024* kbps Performance monitoring: compliant G.826 (errored seconds, severely errored seconds, unavailability seconds) SHDSL Line interface Single or two-pair SHDSL line access (configurable) Coding: TC PAM, compliant to ITU-T G.991.2 (G.SHDSL) and ETSI TS 101524 Connector: 50 pin telco connector Line speeds: Single-pair: N x 64 kbps (N = 3 36) Two-pair: N x 128 kbps (N = 3 36) Handshaking: compliant G.994.1 (automatic speed negotiation) or fixed speed Performance monitoring: compliant G.826 (errored seconds, severely errored seconds, unavailability seconds) Fixed Ethernet uplink Connector: RJ45 Encapsulations: IEEE 802.3 (10Mbps Ethernet), IEEE 802.3u (100Mbps Ethernet) Speed: 10/100Mbps auto-sense Modular uplink interfaces Multiple E1 Connector: 6x RJ45 Electrical: G.703, 120 Ohm Supported layer-2 protocols: ATM, ATM IMA, Frame-relay*, multi-link Frame-Relay*, PPP*, multi-link PPP* status LED per port E3/T3* Connector: BNC Electrical G.703, 75 Ohm Speed: 34 Mbps or 45 Mbps Supported layer-2 protocols: ATM, Frame-Relay*, PPP* status and test LED STM1* UTP Connector: RJ45 Telindus 2400 Series data sheet Version 2.0 30 January 2004 3 / 7
Speed: 155 Mbps Supported layer-2 protocols: ATM status and test LED Optional SFP fibre interface Versions: dual fibre 1300 nm, multimode short haul, typ. 2 km dual fibre 1300nm, single mode medium haul, typ. 50km single fibre 1300-1500nm, single mode medium haul, typ. 15km Speed: 155 Mbps Supported layer-2 protocols: ATM status and test LED Ethernet Connector: RJ45 Encapsulations: IEEE 802.3 (10Mbps Ethernet), IEEE 802.3u (100Mbps Ethernet) Speed: 10/100Mbps auto-sense Integrated 4 ports Ethernet switch 1 status LED per port Local Maintenance interface Local 9-pin sub-d connector Station clock interface G.703/G.704, 2048 kbps, RJ45 120 Ohm ATM encapsulation Applicable for modular uplink ATM implementation conform ITU-T I.311, I.321, I.361, I.432 ATM forum UNI 3.1/4.0 PVCs ATM forum ILMI 3.1/4.0 OAM F4/F5 loop-back, Continuity Check* (ITU-T I.610) Supports ATM Forum Traffic Management 4.1 service types CBR, UBR, VBR-rt, VBR-nrt and UBR+ Supports up to 32 ATM PVCs for each DSL interface DSL encapsulation schemes: Multiprotocol encapsulation in AAL5 LLC and VC multiplexed (RFCs 1483, 2684) PPPoA LLC and VC multiplexed (RFC 2364) PPPoE LLC multiplexed (RFC 2516) Frame-Relay encapsulation* Applicable for modular uplink Encapsulation compliant with RFCs 1490, 2427 Support of multiple DLCI s (PVC) CIR (Committed Information Rate) configurable per DLCI EIR (Excess Information Rate) configurable per DLCI Support of Inverse ARP over Frame-Relay for automatic gateway configuration Support of LMI (revision 1 LMI, ANSI T1.617 and ITU-T) Multilink Frame Relay (FRF.15) Frame Relay fragmentation (FRF.12) Up to 256 DLCIs PPP encapsulation* Applicable for modular uplink Encapsulation compliant with RFCs 1661, 1662 IPCP (RFC 1332) BCP (RFC 2878) Support of PAP authentication and CHAP authentication with MD5 hashing (RFC 1994) PPP multilink (RFC 1990) including PPP fragmentation Telindus 2400 Series data sheet Version 2.0 30 January 2004 4 / 7
PPP multiclass (RFC 2686) IP Routing IP (RFC 791) ARP (RFC 826) Static routing, RIP1 (RFC 1058), RIP2 with MD5 hashing and authentication (RFC 2453), OSPF* (RFC 2328) Router requirements (RFC 1812) Standard and extended access filtering on all router ports NAT (Network Address Translation) with dynamic or static IP address conversion and PAT (Port Address Translation) (RFC 3022) BOOTP/DHCP server, client, relay agent (RFC 2131, RFC 951, RFC 2132) Numbered/unnumbered WAN Interface Traffic policies based on access lists and TOS bits DiffServ priority and drop precedence (RFC 2474, RFC 2475) Priority policies FIFO, round robin, absolute priority, WFQ, low delay WFQ Policy based routing Traffic shaping* L2TP tunneling (RFC 2661) on WAN and LAN interfaces L2TP LAC* including the use of RADIUS (RFC 2809) Support for up to 256 L2TP tunnels Bridging and VLAN switching Bridging with spanning tree protocol (IEEE 802.1D) Bridging without multicast/broadcast traffic between neighbour DSL lines Multiple bridge groups (up to 32) VLAN interconnect (IEEE 802.1Q) VLAN priority queuing (IEEE 802.1P) DSL line to VLAN mapping VLAN switching* Support for up to 256 VLANs ATM switching Conform ITU-T I.371 for traffic and congestion control Support for up to 1024 PVCs Front panel indications PWR: Power indication for each power inlet R: Reset condition LAN: Lan status CLK: Station clock status DCD: Data Carrier Detect for each DSL line Clocking Slave on STM1, E3, T3 or E1 uplink Station clock (G.703 clock input) Internal Maintenance and management support Local console (VT100 command line interface or interactive interface) TELNET (command line interface or interactive interface) (RFC 854) TMA (Telindus Maintenance Application) HTTP web interface (RFC 2616) PING (RFC 792) SNMP MIB2 (RFC 1213), private MIB Syslog client (RFC 3164) SNTP client (RFC 2030) RADIUS client (RFC 2865) DNS client* Telindus 2400 Series data sheet Version 2.0 30 January 2004 5 / 7
FTP and TFTP configuration and firmware flash download (RFC 414, RFC 1350) 2 alarm contact outputs (normally open and closed contacts) 7 alarm input contacts with common return (normally closed contacts) TMA CLI stand-alone command line console software** TMA for HP OV management integration in HP Openview** Mechanical data H x W x D: 44 x 440 x 240 mm (desktop) Weight: 3.5 kg Power requirements DC: -36 up to -72V AC: 85 264V, 47 63 Hz Power consumption: 8P versions: 25 W 16P versions: 35W 24P versions: 45 W Environmental conditions Storage: ETS 300019-1-1 class 1.1 Transportation: ETS 300019-1-2 class 2.3 Stationary use: ETS 300019-1-3 class 3.2 ETSI racks ETS 300019-2/-3/-4 IEC 60529 protection IP30 Temperature controlled fan Memory 32MByte DRAM 16MByte Flash Available accessories ADSL splitters Rack mount kit AC power supplies Telco cables Sales codes Code Product Description 182573 TELINDUS 2401 ADSL ANNEXA S BU 182735 TELINDUS 2401 ADSL ANNEXA S BU AC/ 8 lines ADSL annex A, internal line splitter, redundant 8 lines ADSL annex A, internal line splitter, 182736 TELINDUS 2401 ADSL ANNEXA BU 8 lines ADSL annex A, redundant 182737 TELINDUS 2401 ADSL ANNEXA BU AC/ 182574 TELINDUS 2401 ADSL ANNEXB S BU 182738 TELINDUS 2401 ADSL ANNEXB S BU AC/ 8 lines ADSL annex A, internal line splitter, 8 lines ADSL annex B, internal line splitter, redundant 8 lines ADSL annex B, internal line splitter, 182739 TELINDUS 2401 ADSL ANNEXB BU 8 lines ADSL annex B, redundant 182740 TELINDUS 2401 ADSL ANNEXB BU AC/ 8 lines ADSL annex B, internal line splitter, 182575 TELINDUS 2402 ADSL ANNEXA BU 16 lines ADSL annex A, redundant 182576 TELINDUS 2402 ADSL ANNEXB BU 16 lines ADSL annex B, redundant 182577 TELINDUS 2403 ADSL ANNEXA BU 24 lines ADSL annex A, redundant 182578 TELINDUS 2403 ADSL ANNEXB BU 24 lines ADSL annex B, redundant Telindus 2400 Series data sheet Version 2.0 30 January 2004 6 / 7
181305 TELINDUS 2421 SHDSL BU 8 lines SHDSL, redundant 183065 TELINDUS 2421 SHDSL BU AC/ 8 lines SHDSL, 181306 TELINDUS 2422 SHDSL BU 16 lines SHDSL, redundant 181307 TELINDUS 2423 SHDSL BU 24 lines SHDSL, redundant 184106 SPLITTER 24P POTS 24 lines POTS splitter 184107 SPLITTER 24P ISDN 24 lines ISDN splitter 181308 TIM 4P 100BASE TX Telindus Interface Module 4 ports 10/100 Ethernet interface with built-in Ethernet switch 181309 TIM STM1 BU Telindus Interface Module STM1 with UTP interface and 2 free slots for fibre interfaces. (possible redundancy). Basic unit, fibre modules not included. 188295 SFP13 DUAL FIBRE MM-SH Small Form Pluggable dual fibre, Multi-Mode, 1310nm, Short-Haul. Suitable for TIM STM1 BU code 181309 188296 SFP13 DUAL FIBRE SM-MH Small Form Pluggable dual fibre, Single-Mode, 1310nm, Medium-Haul. Suitable for TIM STM1 BU code 181309 188297 SFP13-15 SINGLE FIBRE SM-MH Small Form Pluggable single fibre, Single-Mode, Tx 1310nm - Rx 1550nm, Medium-Haul. Suitable for TIM STM1 BU code 181309 188298 SFP15-13 SINGLE FIBRE SM-MH Small Form Pluggable single fibre, Single-Mode, Tx 1550nm - Rx 1310nm, Medium-Haul. Suitable for TIM STM1 BU code 181309 181310 TIM E3/T3 BNC Telindus Interface Module E3/T3 with BNC connectors 181312 TIM 6E1 IMA Telindus Interface Module with 6 E1 interfaces RJ45 connectors supporting ATM IMA 183021 TELINDUS RACK MOUNT KIT Rack mount kit for 19 and ETSI racks 185881 DESK-TOP PWR MOD 230VAC-> 70W Optional External Desk-top Power supply module (230/115Vac -> 48Vdc). 183019 TELINDUS 2901 PSU CHASSIS Rack mountable chassis for up to 4 270W PSUs (suitable for 19 rack) 183020 TELINDUS 2902 230VAC / PSU 270W 270W PSU for 230VAC to conversion Notes: Information in this document is subject to change without notice. Telindus assumes no responsibility for errors that appear in this document. The products and features listed in this document are available in Q1 2004. Some features are marked with a *. Those are not yet supported in the software release in Q1 2004. Upgrades can be downloaded from the Telindus website. The Telindus 2402, 2403, 2422 and 2423 versions as well as the TIM E3/T3 and TIM STM1 interfaces are available in Q2 2004. Features marked with a ** are optional items. Telindus 2400 Series data sheet Version 2.0 30 January 2004 7 / 7