JCT s Dialogic D/480JCT-2T1 and Dialogic D/600JCT-2E1 The Dialogic D/480JCT-2T1 is a 48-port Digital T1 PCI Express board and the Dialogic D/600JCT-2E1 is a 60- port Digital E1 PCI Express board. Both of these boards are well-suited for developing advanced communications applications requiring digital network interfaces as well as multimedia resources. These high performance, scalable products support voice, fax, and softwarebased speech recognition processing in a single PCI Express slot. Dialogic JCT s including these models - can be used by developers to provide small- and medium-sized enterprise Computer Telephony (CT) applications that require high-performance voice and fax processing. Among the features and benefits of these boards, and other Dialogic JCT s, are the following. They have On-board Digital Signal Processor (DSP) based voice processing technology and they are well-suited for server-based CT systems under Windows and Linux. They also provide a powerful platform for creating sophisticated Interactive Voice Response (IVR) applications for the small and medium-sized enterprise market segment. Features such as fax and software-based speech recognition processing enable unified messaging applications. They also provide Automatic Gain Control (AGC), so even a weak telephone signal can be recorded and replayed with clarity. Features 48 to 60 independent voice channels, and 24 to 48 T1 or 30 to 60 E1 network channels in a single PCI Express slot Supports G.726 bit exact and GSM coders Silence-compressed recording Unified call control access through Dialogic Global Call Software interface Available with PCI Express edge connector Supports DSP-based onboard fax and host-based speech recognition (fax and host-based speech recognition are mutually exclusive) Benefits Lower costs while creating larger high-density systems with fewer boards per chassis Enables implementation of unified messaging applications that meet VPIM standards Eliminates silence and preserves hard disk space Provides worldwide application portability and shortens development time by using the same API for almost any network protocol PCI Express form factor compatible with x1 slot (x1 or higher compatible). Maximizes the number of boards in the system
Dialogic D/480JCT-2T1 and Dialogic D/600JCT-2E1 JCT s Technical Specifications D/480JCT-2T1 Number of ports 48 Maximum boards per system 10. Number may be limited by factors including application, system performance, and the number of CT Bus loads per board CT Bus loads per board Approximately 4 Maximum CT Bus loads per system 20 Digital network interface Onboard DSX-1 interface Resource sharing bus H.100 CT Bus Control microprocessors 4 Intel486 GX processors Digital signal processor Freescale DSP56303 @ 100 MHz, with 128Kx24 private Supported operating systems Windows; Linux. Details at www.dialogic.com/systemreleases CSP Yes Signaling Digital ISDN PRI (CAS) Host Interface Bus compatibility Bus speed Shared memory Interrupt I/O ports Complies with PCI-SIG PCI Express Base Specification, Rev. 1.1; x1 or higher compatible 2.5 GHz maximum per direction 32 KB to 64 KB page Legacy INTA emulation shared by Dialogic JCT PCIe s None Physical Dimensions Standard-height, full-length form factor 12. 283 in. (31.200 cm) long (without edge retainer) 0.79 in. (2.007 cm) wide (total envelope) 3.87 in. (9.830 cm) high (excluding edge connector) Power Requirements +3.3 VDC 1.12 A typical, 1.4 A maximum +12 VDC 800 ma typical, 900 ma maximum Environmental Requirements Operating temperature Storage temperature Humidity +32 F (0 C) to +104 F (+40 C) -4 F ( 20 C) to 158 F (+70 C) 8% to 80% noncondensing Telephone Interface Clock rate 1.544 Mb/s ±32 ppm Level 3.0 V (nominal) Pulse width 323.85 ns (nominal) Line impedance 100 Ohm ±10% Other electrical characteristics Complies with AT&T TR62411 and ANSI T1.403-1989 Framing SF (D3/D4) ESF for ISDN Line coding AMI AMI with B7 stuffing B8ZS Clock and data recovery Complies with AT&T TR62411 and Telcordia TA-TSY-000170 Jitter tolerance Complies with AT&T TR62411 and ANSI T1.403-1989 2
Dialogic D/480JCT-2T1 and Dialogic D/600JCT-2E1 JCT s Connectors Telephony bus connector Loopback Reliability Estimated MTBF RJ-48C H.100-style 68-pin fine pitch card edge connector Supports switch-selectable local analog loopback and software-selectable local digital loopback Per Telcordia Method PCI Express: 154,000 hours D/600JCT-2E1 Number of ports 60 Maximum boards per system 10. Number may be limited by factors including application, system performance, and the number of CT Bus loads per board CT Bus loads per board Approximately 4 Maximum CT Bus loads per system 20 Digital network interface Onboard E-1 interface Resource sharing bus H.100 CT Bus Control microprocessors 4 Intel486 GX processors Digital signal processor Freescale DSP56303 @ 100 MHz, with 128Kx24 private Supported operating systems Windows; Linux. Details at www.dialogic.com/systemreleases CSP One E1 span only Signaling R2MF Host Interface Bus compatibility Bus speed Shared memory Interrupt I/O ports Complies with PCI-SIG PCI Express Base Specification, Rev. 1.1; x1 or higher compatible 2.5 GHz maximum per direction 32 KB to 64 KB page Legacy INTA emulation shared by Dialogic JCT PCIe s None Physical Dimensions Standard-height, full-length form factor 12.283 in. (31.200 cm) long (without edge retainer) 0.79 in. (2.007 cm) wide (total envelope) 3.87 in. (9.830 cm) high (excluding edge connector) Power Requirements +3.3 VDC 1.12 A typical, 1.4 A maximum +12 VDC 800 ma typical, 900 ma maximum Environmental Requirements Operating temperature Storage temperature Humidity +32 F (0 C) to +104 F (+40 C) -4 F ( 20 C) to 158 F (+70 C) 8% to 80% noncondensing Telephone Interface Network clock rate 2.048 Mb/s ±50 ppm Internal clock rate 2.048 Mb/s ±32 ppm Level 2.37 V (nominal) for 75 Ohm lines 3.0 V (nominal) for 120 Ohm lines Pulse width 244 ns (nominal) Line impedance 75 Ohm, unbalanced 120 Ohm, balanced Other electrical characteristics Complies with ITU-T Rec. G.703 3
Dialogic D/480JCT-2T1 and Dialogic D/600JCT-2E1 JCT s Framing Line coding Clock and data recovery Jitter tolerance Connectors Telephony bus connector Loopback ITU-T G.704-1988 with CRC4 HDB3 Complies with ITU-T Rec. G.823-1988 Complies with ITU-T Rec. G.823, G.737, G.739, G.742-1988 BNC for 75 Ohm lines RJ-48C for 120 Ohm lines H.100-style 68-pin fine pitch card edge connector Supports switch-selectable local analog loopback and software-selectable local digital loopback Reliability Estimated MTBF Per Telecordia Method 1 154,000 hours Approvals, Compliance and Warranty Environmental Information Country-specific safety and telecom approvals Warranty information www.dialogic.com/en/company/environmental-policy.aspx www.dialogic.com/en/products/others/declarations.aspx www.dialogic.com/en/warranties.aspx Springware/JCT Technical Specifications Facsimile Fax compatibility Data rate Variable speed selection Transmit data modes Receive data modes File data formats ASCII-to-fax conversion Error correction Image widths Image scaling Polling modes Image resolution Fill minimization Audio Signal Receive range Automatic gain control Silence detection ITU-T G3 compliant (T.4, T.30) ETSI NET/30 compliant 14,400 b/s (v.17) send 9600 b/s receive Automatic step-down to 12,000 b/s, 9600 b/s, 7200 b/s, 4800 b/s, and lower Modified Huffman (MH) Modified Read (MR) MH, MR Tagged Image File Format-Fax (TIFF-F) for transmit/receive MH and MR Host-PC-based conversion Direct transmission of text files Windows fonts supported Page headers generated automatically Detection, reporting, and correction of faulty scan lines 1728 pixels 2048 pixels 2432 pixels Automatic horizontal and vertical scaling between page sizes Normal Turnaround Normal (203 pels/in. 98 lines/in., 203 pels/2.54 cm 98 lines/2.54 cm) Fine (203 pels/in. 196 lines/in., 203 pels/2.54 cm 196 lines/2.54 cm) Automatic fill bit insertion and stripping (T-1) 40 to +2.5 dbm0 nominal, configurable by parameter** (E-1) 43 to +2.5 dbm0 nominal, configurable by parameter** Application can enable/disable Above 18 dbm0 (T-1) or 21 dbm0 (E-1) results in full-scale recording, configurable by parameter** 38 dbm0 nominal, software adjustable** 4
Dialogic D/480JCT-2T1 and Dialogic D/600JCT-2E1 JCT s Transmit level (weighted average) Transmit volume control (T-1) 9 dbm0 nominal, configurable by parameter** (E-1) 12.5 dbm0 nominal, configurable by parameter** 40 db adjustment range, with application-definable increments and legal limit cap Frequency Response 24 kbit/s 300 Hz to 2600 Hz ±3 db 32 kbit/s 300 Hz to 3400 Hz ±3 db 48 kbit/s 300 Hz to 2600 Hz ±3 db 64 kbit/s 300 Hz to 3400 Hz ±3 db Audio Digitizing 13 kbit/s GSM @ 8 khz sampling 24 kbit/s OKI ADPCM @ 6 khz sampling 32 kbit/s OKI ADPCM @ 8 khz sampling 32 kbit/s G.726 @ 8 khz sampling 48 kbit/s A-law G.711 PCM @ 6 khz sampling 48 kbit/s µ-law G.711 PCM @ 6 khz sampling 64 kbit/s A-law G.711 PCM @ 8 khz sampling 64 kbit/s µ-law G.711 PCM @ 8 khz sampling Digitization selection Playback speed control DTMF Tone Detection Selectable by application on function call-by-call basis Pitch controlled Available on OKI ADPCM and G.711 PCM Adjustment range: ±50% Adjustable through application or programmable DTMF control DTMF digits 0 to 9, *, #, A, B, C, D per Telcordia LSSGR Sec 6 Dynamic range Minimum tone duration Interdigit timing Acceptable twist and frequency variation Noise tolerance Cut-through Talk-off 36 dbm0 to 3 dbm0 (T-1) or 39 dbm0 to 0 dbm0 (E-1) per tone, configurable by parameter** 40 ms, can be increased with software configuration Detects like digits with a >40 ms interdigit delay Detects different digits with a 0 ms interdigit delay (T-1) Meets Telcordia LSSGR Sec 6 and EIA 464 requirements (E-1) Meets appropriate ITU-T specifications** Meets Telcordia LSSGR Sec 6 and EIA 464 requirements for Gaussian, impulse, and power line noise tolerance (T-1) Local echo cancellation permits 100% detection with a >4.5 db return loss line (E-1) Digital trunks use separate transmit and receive paths to network Performance dependent on far-end handset s match to local analog loop Detects less than 20 digits while monitoring Telcordia TR-TSY-000763 standard speech tapes (LSSGR requirements specify detecting no more than 470 total digits) Detects 0 digits while monitoring MITEL speech tape #CM 7291 Global Tone Detection Tone type Maximum number of tones Frequency range Maximum frequency deviation Frequency resolution Timing Dynamic range Programmable for single or dual Application-dependent Programmable within 300 Hz to 3500 Hz Programmable in 5 Hz increments ±5 Hz. Separation of dual frequency tones is limited to 62.5 Hz at a signal-to-noise ratio of 20 db Programmable cadence qualifier, in 10 ms increments (T-1) Programmable, default set at 36 dbm0 to 0 dbm0 (single tone), 3 dbm0 (dual tone) (E-1) Programmable, default set at 39 dbm0 to +0 dbm0 per tone 5
Dialogic D/480JCT-2T1 and Dialogic D/600JCT-2E1 JCT s Global Tone Generation Tone type Frequency range Frequency resolution Duration Amplitude Generate single or dual tones Programmable within 200 Hz to 4000 Hz 1 Hz 10 ms increments (T-1) 43 dbm0 to 3 dbm0 per tone nominal, programmable (E-1) 40 dbm0 to +0 dbm0 per tone nominal, programmable MF Signaling (T-1) R1 MF digits 0 to 9, KP, ST, ST1, ST2, ST3 per Telcordia LSSGR Sec 6, TR-NWT-000506 and ITU-T Q.321 Transmit level Signaling mechanism Dynamic range for detection Acceptable twist Acceptable frequency variation MF Signaling (E-1) Complies with Telcordia LSSGR Sec 6, TR-NWT-000506 Complies with Telcordia LSSGR Sec 6, TR-NWT-000506 25 dbm0 to 3 dbm0 per tone 6 db Less than ±1 Hz R2 MF digits All 15 forward and backward signal tones per ITU-T Q.441 Transmit level Signaling mechanism Dynamic range for detection Acceptable twist Acceptable frequency variation Call Progress Analysis Busy tone detection Ring back tone detection Positive voice detection Positive answering machine detection Fax/modem detection Intercept detection Dial tone detection before dialing 8 dbm0 per tone, nominal, per ITU-T Q.454; programmable Supports the R2 compelled signaling cycle and non-compelled pulse requirements per ITU-T Q.457 and Q.442 35 dbm0 to 5 dbm0 per tone 6 db Less than ±1 Hz Tone Dialing DTMF digits Frequency variation Rate Level 0 to 9, *, #, A, B, C, D per Telcordia LSSGR Sec 6, TR-NWT-000506 Less than ±1 Hz 10 digits/s, configurable by parameter** 7.5 dbm0 per tone, nominal, configurable by parameter** Pulse Dialing 10 digits 0 to 9 Pulsing rate 10 pulses/s, nominal, configurable by parameter** Break ratio 60% nominal, configurable by parameter** Analog Display Services Interface (ADSI) FSK generation per Telcordia TR-NWT-000030 CAS tone generation and DTMF detection per Telcordia TR-NWT-001273 Ordering Information Please see the Ordering Information tab for this product 6
www.dialogic.com For a list of Dialogic locations and offices, please visit: https://www.dialogic.com/contact.aspx Dialogic is a registered trademark of Dialogic Corporation and its affiliates or subsidiaries ( Dialogic ). Dialogic s trademarks may be used publicly only with permission from Dialogic. Such permission may only be granted by Dialogic s legal department at 6700 Cote-de-Liesse Road, Suite 100, Borough of Saint-Laurent, Montreal, Quebec, Canada H4T 2B5. The names of actual companies and products mentioned herein are the trademarks of their respective owners. Dialogic encourages all users of its products to procure all necessary intellectual property licenses required to implement their concepts or applications, which licenses may vary from country to country. None of the information provided in this other than what is listed under the section entitled Technical Specifications forms part of the specifications of the product and any benefits specified are not guaranteed. No licenses or warranties of any kind are provided under this datasheet. Dialogic may make changes to specifications, product descriptions, and plans at any time, without notice. Any use case(s) shown and/or described herein represent one or more examples of the various ways, scenarios or environments in which Dialogic products can be used. Such use case(s) are non-limiting and do not represent recommendations of Dialogic as to whether or how to use Dialogic products. Positive Answering Machine Detection/Positive Voice Detection These performance results were measured using specific computer systems and/or components within specific lab environments and under specific system configurations. Any difference in system hardware, software design, or configuration may affect actual performance. The results are furnished for informational use only and should not be construed as a commitment by Dialogic. Dialogic assumes no responsibility or liability for any errors or inaccuracies. Outbound Dialing/Telemarketing Outbound dialing systems may be subject to certain laws or regulations. Dialogic makes no representation that Dialogic products will satisfy the requirements of any such laws or regulations (including, without limitation, any regulations dealing with telemarketing). **Configurable to meet country-specific PTT requirements. Actual specification may vary from country to country for approved products. Copyright 2015 Dialogic Corporation. All rights reserved. 12/15 7131-11