Analog Timers Key features of the RTE series include: time ranges and timing functions ON-delay, interval, OFF-delay, one-shot Time delays up to 0 hours Space-saving package (." x." x.0") High repeat accuracy of ± 0.% saving.va consumption ON and timing OUT LED indicators Standard 8- or -pin and -blade termination form C delayed output contacts 0A Contact Rating UL Listed File No. E0 CSA Certified File No. LR88 Cert. No. E9909 (EMC, RTE) Cert. No. BL908 (LVD, RTE) Contact Configuration Form C, DPDT (delay outputs) Internal Circuits Specifications Input Voltage Contact Rating Consumption Repeat Accuracy Voltage Accuracy Temperature Error Setting Error Reset Time Insulation Resistance Dielectric Strength 0V AC, 0/0Hz V AC/DC V AC/DC 0A resist. at 0V AC, 0V DC A induct. at 0V AC, 0V DC / HP at 0V AC / HP at 0V AC ON-delay/interval AC:.VA to.va DC: 0.9W to.w OFF-delay/single-shot AC:.VA to.va DC: 0.9W to.w ± 0.% maximum, 0ms ± % maximum, ± 0ms ± % maximum, ± 0ms ± 0% maximum 0.s maximum 00 MΩ minimum 00V AC, minute (except between contacts of same pole) Vibration Resistance N (approximate ) Blade Terminals ON-Delay/Interval A 8 9 B 8-Pin OFF-Delay/e-Shot Pin Terminals (+) (-) (+) (AC or DC) (-) 8 POWER Control Signal Switch A 8 9 B (+) (AC or DC) (-) Control Signal Switch 0 (+) (-) POWER -Pin 8 9 Shock Resistance 00N (approximate 0) Operating Temperature 0 C to + C Do not apply voltage to terminals and. Do not apply voltage to terminals and. Operating Humidity to 8% RH RTE Table of Contents Part Number uide-9 Part Number List-9 RTE Timing Diagrams-0 RTE Accessories- Instructions: Setting Timer- RTE Dimensions- -8 www.idec.com USA: (800) -IDEC or (08) -00, Canada (888) -IDEC
Part Numbering uide RTE series part numbers are composed of part number codes. When ordering a RTE series part, select one code from each category. Example: -AC0V RTE P AC0V ➀ Series ➁ Terminal Style ➂ Function roup ➃ Time Range roup Input Voltage Part Numbers: Description Part Number Code Remarks ➀ Series RTE series RTE For internal circuits, see previous page. ➁ Terminal Style ➂ Function roup ➃ Time Range roup Input Voltage Pin Blade P B Select one only. ON-delay/interval Each function group has two timing functions. OFF-delay/one-shot See page -0. 0.s to 0 minutes 0. minutes to 0 hours 0V AC, 0/0Hz V AC/DC V AC/DC AC0V V V Each time group has 8 selectable ranges. See page -. Part Number List Part Numbers Part No. Mode of Operation Time Range ON-Delay/Interval OFF-Delay/e-Shot 0. seconds to 0 minutes RTE-B 0. minutes to 0 hours RTE-B 0.s to 0 minutes RTE-B 0. minutes to 0 hours RTE-B. After basic part number, insert input voltage.. For schematics, see page -8.. For timing diagrams, see page -0.. All timers have multiple time ranges. For a list of ranges, see page -.. For socket and accessory information, see page -. www.idec.com USA: (800) -IDEC or (08) -00, Canada (888) -IDEC -9
Timing Diagrams ON-Delay (delay on make): When power is applied to the input terminals, the time delay period begins. At the end of the time delay period, the output contacts transfer. Removing power prompts a reset. (Terminal No.) ON-Delay (RTE-P, RTE-B) (-) (A-B) (-) (-) (-) (-) (8-) (9-) (8-) (9-) Indicator Interval: When power is applied to the input terminals, the output contacts instantly transfer and the time delay period begins. At the end of the time delay period, the output contacts de-energize. Removing power prompts a reset. (Terminal No.) Interval (RTE-P, RTE-B) (-) (A-B) Indicator (-) (-) (-) (-) (8-) (9-) (8-) (9-) OFF-Delay (delay on break): must be applied at all times to the input terminal. closure of a normally open control signal switch, the output contacts transfer and remain in this position. When the control switch is reopened, the time delay period begins. At the end of the time delay period, the output contacts transfer back to original position. Reset occurs when the control signal switch is closed. Control Signal OFF-Delay (RTE-P, RTE-B) (Terminal No.) (-0) (A-B) Control Signal (-) (-) Indicator (-) (-) (-) (-) (8-) (9-) (9-) (9-) e-shot: must be applied at all times to the input terminals. momentary or maintained closure of a normally open control signal switch, the output contacts transfer and the time delay period begins. At the end of the delay period, the output contacts transfer back to the original positions. The timer is then ready for the next timing cycle. Control Signal Indicator -0 www.idec.com USA: (800) -IDEC or (08) -00, Canada (888) -IDEC Single-Shot (RTE-P, RTE-B) (Terminal No.) (-0) (A-B) Control Signal (-) (-) (-) (-) (-) (-) (8-) (9-) (9-) (9-)
DIN Rail Mounting Accessories Part Numbers: DIN Rail/Surface Mount Sockets and Hold-Down Springs DIN Rail Mount Socket Applicable Hold-Down Springs Style Appearance Use with Timers Part No. Appearance Part No. 8-Pin Screw Terminal (dual tier) SRP-0 -Pin Screw Terminal (dual tier) SRP-0 SFA-0 8-Pin Fingersafe Socket SRP-0C -Pin FingerSafe Socket SRP-0C 8-Pin Screw Terminal SRP-0 -Pin Screw Terminal SRP-0 SFA-0 -Blade Screw Terminal RTE-B RTE-B RTE-B RTE-B SRB-0 DIN Mounting Rail Length 000mm BNDN000 Installation of Hold-Down Springs DIN Rail Mount Socket Insert the springs into the outer slots with the projections facing inside. Insert the springs into the slots. Socket SRP-0 Hold Down Spring SFA-0 Socket SRP-0 Hold Down Spring SFA-0 ce installed into the sockets, the hold-down springs cannot be removed. www.idec.com USA: (800) -IDEC or (08) -00, Canada (888) -IDEC -
Panel Mounting Accessories Part Numbers: Panel Mount Sockets and Hold-Down Springs Panel Mount Socket Applicable Hold-Down Springs Style Appearance Use with Timers Part No. Appearance Part No. 8-Pin Solder Terminal SRP- SFA-0 -Pin Solder Terminal SRP- -Blade Solder Terminal RTE-B RTE-B RTE-B RTE-B SRB- Part Numbers: Flush Panel Mount Adapter and Sockets that use an Adapter Accessory Description Appearance Use with Part No. Panel Mount Adapter Adaptor for flush panel mounting RTE timers All RTE timers RTB-0 8-pin screw terminal SRP-M08 -pin screw terminal (Shown: SRP-M08 for Wiring Socket Adapter) SRP-M Sockets for use with Panel Mount Adapter 8-pin solder terminal SRP-S08 -pin solder terminal SRP-S No hold down clips are available for flush panel mounting applications. - www.idec.com USA: (800) -IDEC or (08) -00, Canada (888) -IDEC
Instructions Each RTE series electronic timer is available with two functions (operation modes) and eight time ranges. Start by determining which timing function and what time range suits your application. Function roup -AC0V Function Programming. Removal Time Range roup Bend the faceplate slightly and pop out the bottom edge (figure ).. Timing Function Selection Figure Select the function by moving the DIP switch to the right or left position (Figure ). Refer to the table below noting that the function group is the first digit in the part number. After the face plate is replaced, the DIP switch will be visible through the window if it is in the left position. (This is helpful for determining in which mode the timer is set, without removing the faceplate.) Bottom Slot DIP Switch Position Figure Function roup Left Right Interval ON-Delay e-shot OFF-Delay DIP Switch Time Range Programming. Time Range Selection Select the appropriate timer range by rotating the digital switch (figure ). Refer to the table below and note that the time range group is the second digit in the part number. Digital Switch Setting Digital Switch Front View Time Range roup 0 (*8) ** (9) s s s 0s 0s 0s 0 0 0 0 hrs. 0 hrs. Figure *The time setting is the same when the digital switch is at 0 or 8. ** The time setting is the same when the digital switch is at or 9.. Faceplate Configuration Rotate the wheel in the faceplate to correspond with the time range selected in the previous step (figure ). Time Range Time Range roup Color Dial Disk 0 SEC RTE Unit Time Range s s 0s 0s Yellow s 0s 0 Pink 0 0 Violet 0 hrs. 0 hrs. Blue Figure Top Slot. Replacing Faceplate Bend faceplate slightly and replace on the timer (figure ). The digital switch setting should be visible though a window in the faceplate. www.idec.com USA: (800) -IDEC or (08) -00, Canada (888) -IDEC -
Dimensions Dimensions in inches (mm) Front View 8-Pin Terminal -Pin Terminal -Blade Terminal." (0mm).00" (.mm).00" (.mm).9" (.mm).0" (mm) SRP-0 Socket SRP-0 Socket." (0mm).0" (0mm) 0." (8mm) Ø0." (Ø.) Mounting Hole 0.9" () 0.99" (.mm) DIN Rail.0" (0mm).0" (9mm) 0." (8mm) Ø0." (.mm) Mounting Hole Ø.0" (Ø) 0.99" (.mm) 0.09" M. (mm).8" Terminal Screw (mm) 0.0" (8mm) 0.88" (mm).8" (mm) M. Terminal Screw 0.0" (8mm) 0.88" (mm) SRB-0 Socket.0" (mm) 0." (8mm)." (8.mm) BNDN000 DIN Rail." ±0.0 (mm ±0.) 0." +0.00, -0 (0.mm +0., -0).9" (mm) 0.08" (mm)." (mm)." (mm) Ø 0." (Ø.).8" (mm) M. Terminal Screw 0." (.mm) 0.9" (mm) + + +.9" (9mm).99" (mm).99" (mm) 9." (000mm) Ø 0.8" x 0.88" Slot, Places (Ø.8mm x.mm) - www.idec.com USA: (800) -IDEC or (08) -00, Canada (888) -IDEC