gigabit industrial ethernet Switch user manual Models 503495, 503532, 503570 Model shown: 503495 INT-503495/503532/503570-UM-0308-01
introduction Thank you for purchasing this INTELLINET NETWORK SOLUTIONS Industrial Gigabit Ethernet Switch: Model 503495 (6-port 10/100Base-TX + 2-port 1000Base-SX [SC] Multi-Mode); Model 503532 (6-port 10/100Base-TX + 2-port 1000Base-LX [SC] Single-Mode); or Model 503570 (6-port 10/100Base-TX + 2-port 10/100/1000Base-TX). Specifically designed for industrial Ethernet applications, this switch has all the functions of an unmanaged switch in a robust, aluminum case that offers IP30-standard protection. To meet industrial device-redundancy requirements, the Industrial Gigabit Ethernet Switch is equipped with a terminal block to provide dual power inputs with reverse polarity protection. Plus, store and forward switching architecture greatly increases the network efficiency: It delivers true nonblocking switching performance to all ports running at full wire speed without any loss of packets. Easy-to-follow instructions in this user manual help make installation of the switch quick and simple, so you ll also soon be enjoying the benefits of these additional features: Auto-sensing RJ-45 ports automatically detect optimal network speeds All RJ-45 ports with Auto MDI-X and NWay auto-negotiation support Alarm relay output to alert of power failure Full/half duplex operation Supports IEEE 802.3x flow control on full duplex and back pressure on half duplex Supports 2048 MAC address entries 128 kbytes buffer memory LEDs for link/activity and full/half duplex DIN rail kit, or wall-mounting ears for 3-way installation Terminal block to provide dual power inputs with reverse polarity protection Lifetime Warranty
hardware DIN-Rail Installation Mounting clamp Switch Spring DIN rail 1. Angle the switch s mounting clamp relative to the DIN rail (above left) so that the rail is positioned under the upper lip of the clamp and behind the metal springs. 2. Push the switch toward the DIN rail until the spring on the mounting clamp clicks in place on the rail (above right). Wall-Mount Installation 1. Remove the DIN rail mounting clamp from the back of the switch. 2. Attach the wall-mount panel to the back panel of the switch using the six included screws. 3. With the wall-mount panel securely connected, attach the switch to a wall or other suitably sturdy vertical surface. Wall-mount panel Switch
Front-Panel Ports & Indicators Model 503495 1 1 2 2 3 3 Model 503532 Model 503570 1 Gigabit ports 2 LEDs 3 Fast Ethernet ports Bottom-Panel Connectors The terminal block connections (L-R): GND, V1+ and V1 (PWR 1), Relay Output (1 A / 24 V DC), V2+ and V2 (PWR 2). To the right of the terminal block is the PWR 3 jack (12 45 V DC). Relay GND V1+ V1 V2+ V2 12 48 V DC power jack
specifications Standards (Models 503495/503532) IEEE 802.3 (10Base-T Ethernet) IEEE 802.3u (100Base-TX Fast Ethernet) IEEE 802.3x (flow control, for full duplex mode) IEEE 802.3z (Fiber Optic Gigabit Ethernet) Standards (Model 503570) IEEE 802.3 (10Base-T Ethernet) IEEE 802.3ab (Gigabit Ethernet) IEEE 802.3u (100Base-TX Fast Ethernet) IEEE 802.3x (flow control, for full duplex mode) General Media support: - Model 503495: 10Base-T Cat3, 4, 5 UTP/ STP RJ-45 100Base-TX Cat5 UTP/STP RJ-45 1000Base-SX multi-mode 50/125 µm & 62.5/125 µm fiber - Model 503532: 10Base-T Cat3, 4, 5 UTP/ STP RJ-45 100Base-TX Cat5 UTP/STP RJ-45 1000Base-LX single-mode 9/125 µm fiber - Model 503570: 10Base-T Cat3, 4, 5 UTP/ STP RJ-45 100Base-TX Cat5 UTP/STP RJ-45 1000Base-T Cat5 UTP/STP RJ-45 Packet filter/forwarding rate: - 1,488,000 pps (1000 Mbps) - 148,800 pps (100 Mbps) - 14,880 pps (10 Mbps) Buffer memory: 128 kbytes MAC address table: 2048 entries Backplane speed: 3.2 Gbps Switch architecture: store and forward Certifications: FCC Class A, EN55022 Class A, CE Mark LEDs LINK/ACT Full/half duplex Power Power supply: - Input voltage: 24 V DC (12 48 V DC), dual inputs - Reverse polarity protection: present Power consumption: - Model 503495: 5.5 Watts (maximum) at 24 V - Model 503532: 5.7 Watts (maximum) at 24 V - Model 503532: 5.1 Watts (maximum) at 24 V Environmental Aluminum housing, IP30 protection Dimensions: 53 x 135 x 105 mm W x H x L (2.1 x 5.3 x 4.1 in.) Weight: - Models 503495/503532: 750 g (1.7 lbs.) - Model 503570: 700 g (1.5 lbs.) Operating temperature: -10 70 C (14 158 F) Operating humidity: 5 95% RH, non-condensing Storage temperature: -40 85 C (-40 185 F) Regulatory Approvals EMI: - FCC Class A - EN55022 Class A EMC: - EN61000-4-2 - EN61000-4-3 - EN61000-4-4 - EN6100-4-5 - EN6100-4-6 Safety: - UL - cul - CE/EN60950 Shock: IEC 60068-2-27 Freefall: IEC 60068-2-32 Vibration: IEC 60068-2-6 MTBF: - Model 503495: 283,492 hours - Model 503532: 280,653 hours - Model 503570: 287,250 hours Calculated MTBF is based on MIL-HDBK-217F (Military Handbook) standard Package Contents Industrial Gigabit Ethernet Switch User manual
INTELLINET NETWORK SOLUTIONS offers a complete line of active and passive networking products. Ask your local computer dealer for more information or visit www.intellinet-network.com. Copyright INTELLINET NETWORK SOLUTIONS All products mentioned are trademarks or registered trademarks of their respective owners.