Power Switching & Controls for usiness-critical Continuity
4-hour protection no matter when trouble strikes SCO Series 00 Power Transfer Switches for Power Outage Protection Where would you be without a constant flow of electrical power? We often take for granted that power will always be around when we need it. In reality, power failures are very common. nd when the power goes out, your business suffers. Power failures are unpredictable. They can occur at any time and for any number of reasons a bolt of lightning, a power surge, a blackout, an accident or even equipment failure. They come without warning and often at the most inconvenient times. It s for this reason that many businesses and other entities have invested in emergency power backup systems. Typically, the system consists of an engine generator and an automatic transfer switch (TS) which transfers the load from the utility to the generator. n TS with built-in control logic monitors your normal power supply and senses any interruptions. When the utility power fails, the TS automatically starts the engine and transfers the load after the generator has reached proper voltage and frequency. This happens in a matter of seconds after the power failure occurs. When the utility power has been restored, the TS will automatically switch the load back, and after a time delay, it will shut down the engine. With an utomatic Transfer Switch, you are protected 4 hours a day, seven days a week.
Typical pplications Telecom In the telecommunications industry, providing a high level of service and dependability is crucial. Lost power means an interruption in service for your customers and lost business for your company. For instance, with cell sites scattered across a wide geographical region and in many remote areas, the chances of an interruption in power are increased, making utomatic Transfer Switches a valuable resource at each location. To maintain dependable service, each cell site must be monitored 4 hours a day. This can be very difficult without some type of remote monitoring and testing capability. The Series 00 Transfer Switch, combined with SCO s monitoring and control management system, is a costeffective, packaged solution which can help meet both of these challenging objectives without a major investment at each cell site. With SCO s connectivity solutions you can remotely monitor and control numerous sites from around the corner or around the world. griculture Maintaining electrical power is vital to an agriculture operation. If the flow of power is interrupted, your operation could be at risk unless the backup generator is quickly activated. prolonged power outage can affect numerous aspects of the operation, from housing and feeding livestock to processing and producing the end product. With an SCO Series 00 Transfer Switch, power will automatically be transferred over to your backup generator, eliminating the need to manually switch from utility to generator. When power is restored, the SCO Series 00 Transfer Switch will, after an adjustable time delay to allow for utility stabilization, automatically switch the load back to the utility service. Commercial / Retail, Light Industrial The retail industry is very competitive. n electrical power failure can have a dramatic impact on a retailer s bottom line. If power is interrupted during peak shopping times, the effect could be extremely damaging to present and future business. power interruption will not only suspend shopping, it can also create safety problems, result in lost transaction data, lost account information and damage to data collection equipment. In addition, retailers who rely on controlled climates to protect valuable inventory could suffer even greater losses, especially if the power failure occurs at a time when no one is available to rectify the situation. To avoid any of these power outage problems, simply install a backup generator with an SCO Series 00 Transfer Switch and power outage concerns will be a thing of the past. Municipal The SCO Series 00 Transfer Switch can be a critical component of a municipal government s emergency power backup system. Residents of townships, cities and counties rely on police, fire, ambulance/ first aid and other critical public sector services. n interruption in power would affect the ability of emergency services to effectively respond to the needs of the community. When time is a critical factor, such as when responding to a fire alarm or an emergency call, an SCO Series 00 Transfer Switch can be a lifesaver, switching power to the backup generator. While not all municipal services are a matter of life and death, they are always expected to be there.
Series 00 Power Transfer Switches Maximum Reliability & Excellent Value With a Series 00 Transfer Switch, you get a product backed by SCO Power Technologies, the industry leader responsible for virtually every major technological advance in the Transfer Switch industry. The SCO Series 00 was designed for one purpose to automatically transfer critical loads in the event of a power outage. Each and every standard component was designed by SCO engineers for this purpose. The rugged construction and proven performance of the SCO Series 00 assure the user of many years of complete reliability. The Series 00 is even designed to handle the extraordinary demands placed on the switch when starting or restarting stalled motors and switching high inrush loads. SCO s Series 00 modular, compact design makes it easy to install, inspect and maintain. ll parts are accessible from the front so switch contacts can be easily inspected. Features The Series 00 is listed to UL 1008 standard for Transfer Switch Equipment and CS standard C. for automatic transfer switches. Meets NFP 110 for Emergency and Standby Power Systems and the National Electrical (NEC) rticles 700, 701 and 70. 0 through 000 amps in a compact design. vailable to 600 VC, single or three phase. True double-throw operation: The single solenoid design is inherently inter-locked and prevents contacts from stopping between sources or from being in contact with both sources at the same time. UL Listed Withstand & Close-On Ratings Switch Ratings mps vailable Symmetrical mperes RMS When Used With Current Limiting Fuses Maximum Voltage When Used With Specific Circuit reakers 0 100,000 480v/60Hz 10,000 70-00 00,000 480v/60Hz,000 0 100,000 480v/60Hz,000 60, 400 00,000 480v/60Hz 4,000 600 00,000 600v/60Hz 4,000 600 00,000 480v/60Hz 50,000 600 00,000 40v/60Hz 65,000 800,1000,100 00,000 600v/60Hz 65,000 1600, 000 00,000 600v/60Hz 85,000 600, 000 00,000 600v/60Hz 100,000 Fig. 1: SCO Power Transfer Switch rated 00 amperes shown in Type R enclosure There s no danger of the Series 00 TS transferring loads to a dead source because the unique SCO single-solenoid operator derives power to operate from the source to which the load is being transferred. Easy-to-read flush-mounted control and display panel provides LED indicators for switch position and source availability. It also includes test and time-delay bypass switches as standard features. Standard engine exerciser for weekly automatic testing of engine generator set with or without load. djustable time-delay feature prevents switch from being activated due to momentary utility power outages and generator dips. Supplied with solid neutral termination. Optional switched neutral pole available. ccessory kits available. vailable for immediate delivery. Now available for service entrance applications. Contact sco for assistance. 4 Notes: 1. Current limiting fuse should be Class J type through 400 amps: use Class L type above 400 - amp fuse rating. Refer to publication 118 for specific manufacturer s breakers
Series 00 Power Transfer Switches Designed to Fit nywhere The SCO Series 00 product line represents the most compact design of automatic power transfer switches in the industry. With space in electrical closets being at a premium, the use of wall or floor-mounted SCO Power Transfer Switches assures designers optimum utilization of space. ll transfer switches through 000 amps are designed to be completely front accessible. This permits the enclosures to be installed flush to the wall and still allows installation of all power cabling and connections from the front of the switch. Cable entrance plates are also standard on the 1600 and 000 amp units to install optional side-mounted pull boxes for additional cable bending space. Fig. : SCO Power Transfer Switch rated 00 amperes Fig. : SCO Power Transfer Switch rated 400 amperes Fig. 4: SCO Power Transfer Switch rated 600 mperes Fig. 5: SCO Power Transfer Switch rated 1000 amperes Fig. 6: SCO Power Transfer Switch rated 000 amperes shown in Type R enclosure Fig. 7: SCO Power Transfer Switch rated 000 amperes 5
Series 00 Microprocessor Controller The SCO Microprocessor Controller is used with all sizes of Power Transfer Switches. It represents the most reliable microprocessor controller in the industry and includes, as standard, all of the voltage, frequency, control, timing and connectivity functions required for most emergency and standby power applications. Fig. 8: SCO Series 00 Microprocessor Controller Fig. 9: Door-Mounted Control & Display Panel Control and Display Panel Easy-to-read flush-mounted control and display panel provides LED indicators for switch position and source availability. It also includes test and time-delay bypass switches. Voltage & Frequency Sensing djustable three-phase, close-differential voltage sensing on normal source. Normal source pickup voltage is adjustable to 95% of nominal; drop-out is adjustable from 70% to 90% of nominal. Frequency sensing on emergency source. Pickup at 95% and dropout at 85% of nominal. Time Delays djustable time delay to override momentary normal source outages to delay all transfer switch and enginestarting signals. Transfer to emergency time delay djustable from 0 to 5 minutes for controlled timing of load transfer to emergency. Re-transfer to normal time delay djustable to 0 minutes. Five-minute unloaded running time delay for emergency engine generator cool down. Four-second time delay to ignore momentary voltage and frequency transients during initial genset loading. Standard Selectable Features Inphase monitor to transfer motor loads, without any intentional off time, to prevent inrush currents from exceeding normal starting levels. Engine exerciser to automatically test backup generator each week Includes control switch for testing with or without load. Selective load disconnect, double-throw contact to operate at an adjustable 0 to 0 second adjustable time delay prior to transfer and reset 0 to 0 seconds after transfer. 60 Hz or 50 Hz selectable switch. Three-phase/single-phase selectable switch. Remote Control Features Terminal provisions for connecting: Remote test switch. Remote contact for test or for peak shaving applications. Circuit will be automatically bypassed if emergency source fails. Remote time-delay bypass switch. 6
Series 00 Microprocessor Controller attery to Maintain Engine Exerciser Clock Settings Simple and ccurate djustment of Voltage, Frequency and Time-Delay Settings Without Need for Meters and Variable Power Supplies Dip Switches for Enabling uilt-in Control Functions Customer Control Interfaces Re-transfer to Normal djustable Time Delay Transfer to Emergency djustable Time Delay Serial Communication Port Fig. 10: Microprocessor Controller Performance Features 600 volt spacing per UL and CS standards. Interfacing relays are industrial grade, plug-in type with dust covers. Meets or exceeds the requirements for Electromagnetic Compatibility (EMC). NSI C7.90/IEEE47 Voltage Surge Test NEM ICS-109.1 Impulse Withstand Test Digital circuitry isolated from line voltages IEC 801- Electrostatic discharge (ESD) immunity ENV50140 and IEC 80-1: Radiated electromagnetic field immunity IEC 801-4 Electrical fast transient (EFT) immunity ENV5014 Surge transient immunity ENV50141: Conducted radio-frequency field immunity EN55011: Group 1, Class conducted and radiated emissions Optically isolated RS-485 Serial Port EN61000-4-11 voltage dips and interruptions immunity 7
Series 00 TS Optional ccessories ccessory 11G programmable engine exerciser that provides for weekly or bi-weekly operation, includes one form C contact for source availability of normal and one contact for availability of emergency (contact rating amps @ 0 Vdc, 0.5 amp @ 15 Vac resistive). The programmable engine exerciser incorporates a 7 day or 14 day time base with a digital readout display. Includes with or without load control selection for exerciser period. ccessory 14/14 uxiliary contacts to indicate position of main contacts. Two () for normal and two () for emergency position (one set is standard). ccessory 44 Strip Heater with thermostat for extremely cold areas to prevent condensation and freezing of this condensation. External 10 volt power source required. Fig. 11: Programmable Engine Exerciser with Source vailability Contacts (ccessory 11G) ccessory 44G Strip Heater with thermostat, wired to load terminals: 08-40, 60-80, 460-480, 550-600 volts. Contains wiring harnesses for all transfer switch sizes. ccessory 7 /7E *See Connectivity Products, Page 18 ccessory 1 protective window that includes a poly-carbonate frame and weather gasket to provide secure access to the membrane interface for the type 1 enclosures. This lockable cover is an alternative to providing R secure enclosures. Fig. 1: Strip Heater Kit (ccessory 44G) Field Conversion Kits for Series 00 Transfer Switches Kit No. Description K6980 Engine Exerciser and source availability contacts (cc. 11G) K6117-001 Strip Heater Kit (15 watt) 10 volt (cc. 44) K6117-00 Strip Heater Kit (15 watt) 08-480 volt (cc. 44G) K60907 Cable Pull ox (1600-000 amp) K4787-001 6 FT Extension Harness 1 K75557-001 Serial Module with or without power manager (cc. 7) K75460-001 Connectivity Module with or without power manager (cc. 7E) K7780-001 Window Kit (cc. 1) 1. For 0-00 mp switches only, not available for 00SE, or 00L Fig. 1: Window Kit (ccessory 1) 8
Series 86 Non-utomatic Power Transfer Switches User-Initiated Control SCO 86 non-automatic transfer switches are generally used in applications where operating personnel are available and the load is not an emergency type requiring automatic transfer of power. The power-switching mechanism and controller is the same hardware used on the highly reliable SCO Series 00 transfer switches. SCO 86s are furnished as standard with a momentary-type selector switch to initiate transfer and re-transfer. They can also be arranged for remote control via SCO s connectivity products. Fig. 14: SCO 86 400 mp Type 1 Enclosure w/optional ccessories 9C, 9D Source vailability Lights Fig. 15: Control and Display Panel Electrical Features: Listed under UL 1008, CS certified: - UL listed through 480 VC. - CS certified through 600 VC. Door-mounted selector switch for local, manually initiated electrical control. Sizes from 0 through 000 amps. vailable to 600 VC, 50 or 60 Hz. Rated for all classes of load transfer. 100% tungsten load ratings through 400 amps. Designed for emergency and standby applications. Same withstand and close-on rating as Series 00. Standard Selectable Control Features: Inphase monitor to transfer motor loads between live sources, without any intentional off time, to prevent inrush currents from exceeding normal starting levels. Selective load disconnect, double-throw contact to operate at an adjustable 0 to 0 second time delay prior to transfer and reset 0 to 0 seconds after transfer. High/Low nominal voltage setting. llows user to adjust for source low reduced voltage conditions in remote areas. 60 Hz or 50 Hz selectable switch. Single/Three-phase selectable switch. Control Features: Switch position indicating signal lights. One auxiliary contact closed when transfer switch is connected to normal and one closed on emergency, standard feature 14/14. Optional ccessories: 6Q Key-operated, momentary source selector switch furnished instead of the standard selector switch. 9C, 9D Source availability lights to provide operator with a local indication of power source availability. ccessory 14/14 auxiliary contacts to indicate position of main contacts. Two () for normal position and two () for emergency position (one set is standard). 7 Serial module (5110) is used to allow local or remote communications with SCO POWERQUEST connectivity products. Special Enclosures (Specify by appropriate code in catalog number): Type R: Rain-tight Type 4: Weatherproof Type 1: Oil Tight 7E Connectivity Module 5150 is used to bring several different serial devices that communicate at different baud rates and with different protocols to a common Ethernet media. 9
To order an SCO Series 00 Power Transfer Switch, complete the following catalog number: 00 + + + 600 + N + 1 + X + C + 11CD + 480 V 60 Hz Product 00 lank Solid 1 Switched Poles mperes Voltage poles, 1Ø poles, Ø Continuous rating 0, 70, 104, 150, 00 4, 0 4, 60, 400, 600, 800, 1000, 100, 1600, 000 600 5, 000 5 C D E F H J K L M N Q R Controller 1 Options lank Insert X C If optional accessories F are required G H L Enclosure Open Type M Type 1 (Standard) Type R Type 4 Type 4X Type 1 Type R Type 4 Type 4X 6 Double Door SS Type RX 6,7 Double Door SS To order an SCO Series 86 Transfer Switch, complete the following catalog number: Optional ccessories 11G Programmable Engine Exerciser 14/14 uxiliary Contacts ( sets) 44, 44G Strip Heater w/ Thermostat 7 Serial Module 7E Connectivity Module 1 Window Kit Specific Volt & Freq This information is necessary to allow correct control settings prior to shipment 86 + + + 600 + N + 1 + X + C + 9C/9D + 480 V 60 Hz Product 86 Notes: Solid 1 Switched Series 00 & 86 Transfer Switch Ordering Information Phase Poles poles, 1Ø poles, Ø mperes Continuous rating 0, 70, 100, 150, 00 4, 0 4, 60, 400, 600, 800, 1000, 100, 1600, 000, 600, 000 5 C D E F H J K L M N Q R 115 10 08 0 0 40 80 400 415 440 460 480 575 600 Voltage 115 10 08 0 0 40 80 400 415 440 460 480 575 600 Controller Options 1 Insert X If optional accessories are required Enclosure lank Open Type C Type 1 (Standard) 1. Specify neutral code C for 60 and 400 amperes only.. vailable 0-1000, and 1600 amps. Use Type R for 100, 000, 600 and 000 amp applications.. 115-10 volt available 0-400 amps only. For other voltages contact SCO. 4. 00 and 0 amp rated switches for use with copper cable only. 5. R type provided as standard for 600-000 amp when outdoor enclosure is required. 6. Type 04 Stainless Steel is standard. Suitable for indoor or outdoor use where there may be caustic or alkali chemicals in use. To provide an improved reduction in corrosion of salt and some chemicals, optional type 16 Stainless Steel is recommended. This is a preferred choice for marine environments. 7. vailable on switches rated 100, 000, 600, and 000 mps. Extended Warranties for Series 00 Transfer Switches Catalog No. Description N P R F G H L M N P R Type R Type 4 Type 4X Type 1 Type R Type 4 Type 4X 6 Double Door SS Type RX 6,7 Double Door SS Optional ccessories 6Q Key-Operated Control 9C/9D Source vailability Lights 14/14 uxiliary Contacts 7 Serial Module ll ccessories 7E Connectivity Module Specific Volt & Freq This information is necessary to allow correct control settings prior to shipment 10 EXW00 EXW00 4EXW00 5EXW00 Two-Year Extended Warranty (Parts & Labor) Three-Year Extended Warranty (Parts & Labor) Four-Year Extended Warranty (Parts & Labor) Five-Year Extended Warranty (Parts & Labor)
Series 00 & 86 Transfer Switch Dimensions and Shipping Weights UL Type 1 Enclosure 4 Switch Rating mps 0, 70, 100*, 104 150, 00 *Series 86 only 0, 60, 400 600 800, 1000 100 1600, 000 1 600, 000 Phase Poles or C or C UL Type R, 4 or 1 Enclosure 1,4,5,6 Switch Rating mps 0, 70, 100*, 104 150, 00 *Series 86 only 0, 60, 400 600 800, 1000 100 6 1600, 000 600, 000 Phase Poles or C or C Dimensions, In. (mm) Width Height Depth 17 1/ (445) 17 1/ (445) 17 1/ (445) 17 1/ (445) 18 (457) 18 (457) 18 (457) 18 (457) 4 (610) 4 (610) 4 (610) 4 (610) 4 (864) 4 (864) 4 (864) 4 (864) 8 (965) 8 (965) 8 (965) 8 (965) 8 (965) 8 (965) 8 (965) 8 (965) 1 (787) 1 (787) 1 (787) 1 (787) 48 (119) 48 (119) 48 (119) 48 (119) 6 (1600) 6 (1600) 6 (1600) 6 (1600) 7 (189) 7 (189) 7 (189) 7 (189) 87 (10) 87 (10) 87 (10) 87 (10) 87 (10) 87 (10) 91 (11) 91 (11) 11 5/8 (95) 11 5/8 (95) 11 5/8 (95) 11 5/8 (95) 1 (0) 1 (0) 1 (0) 1 (0) 17 (4) 17 (4) 17 (4) 17 (4) 0 (508) 0 (508) 0 (508) 0 (508) 4 (610) 4 (610) 4 (610) 4 (610) 4 (610) 4 (610) 60 (154) 60 (154) Dimensions, In. (mm) Width Height Depth 17 1/ (445) 17 1/ (445) 17 1/ (445) 17 1/ (445) 18 (458) 18 (458) 18 (458) 18 (458) 4 (610) 4 (610) 4 (610) 4 (610) 4 (864) 4 (864) 4 (864) 4 (864) 41 (104) 41 (104) 41 (104) 41 (104) 41 (104) 41 (104) 41 (104) 41 (104) 5 (886) 5 (886) 5 (886) 5 (886) 50 1/ (184) 50 1/ (184) 50 1/ (184) 50 1/ (184) 6 (160) 6 (160) 6 (160) 6 (160) 75 (1907) 75 (1907) 75 (1907) 75 (1907) 94 1/ (40) 94 1/ (40) 94 1/ (40) 94 1/ (40) 95 1/ (48) 95 1/ (48) 95 1/ (44) 95 1/ (44) 11 5/8 (95) 11 5/8 (95) 11 5/8 (95) 11 5/8 (95) 14 1/ (64) 14 1/ (64) 14 1/ (64) 14 1/ (64) 18.50 (470) 18.50 (470) 18.50 (470) 18.50 (470) 0 (508) 0 (508) 0 (508) 0 (508) 1/ (85) 1/ (85) 1/ (85) 1/ (85) 6 (1577) 6 (1577) 74 (188) 74 (188) pprox. Shipping Weight Lb. (kg) 69 () 7 () 7 () 75 (4) 100 (45) 110 (50) 100 (45) 10 (55) 6 (119) 70 (1) 70 (1) 77 (16) 450 (04) 475 (17) 475 (17) 500 (8) 685 (1) 705 (1) 705 (1) 75 (8) 95 (419) 975 (441) 1700 (771) 15 (969) pprox. Shipping Weight Lb. (kg) 84 (8) 87 (40) 87 (40) 90 (41) 1 (60) 140 (6) 140 (6) 148 (67) 664 (00) 67 (0) 67 (0) 680 (07) 664 (00) 67 (0) 67 (0) 680 (07) 111 (51) 1160 (56) 1160 (56) 1189 (59) 1810 (817) 1860 (84) 005 (905) 070 (98) Notes: 1. Unit is designed for top cable entry of emergency & load and bottom entry of normal. cable pull box is also available for all top or bottom cable access when required (optional accessory kit #K60907). Not required for type R, 4X & 1 enclosures where available.. Enclosures for 600, 000 amps are free-standing with removable top, sides & back.. for 0 amperes only. 4. Dimensional data is approximate and subject to change. Certified dimensions available upon request. Notes: 1. 0-1000 amps non-secure enclosure. 100-000 amps secure enclosure. When climate conditions at installation site present condensation risk, special precautions should be taken, such as the inclusion of space heaters, to prevent interior condensation and freezing of this condensation.. code for 0 amperes only. 4. Dimensions for switch sizes 0-1000 amperes suitable for Type R, 4, or 1 non secure enclosure, 100-000 amperes only suitable for type R. 5. For 100 ampere type 4, or 1 use 1600 amperes secure enclosure dimensions. 6. Dimensional data is approximate and subject to change. Certified dimensions available upon request. Series 00 & 86 External Power Connections Sizes UL-Listed Solderless Screw-Type Terminals Switch Rating (mps) 0-0 60, 400 600 800, 1000, 100 1600, 000 600, 000 Ranges of L-CU Wire Sizes (Unless Specified Copper Only) One #14 to 4/0 WG Two 1/0 WG to 50 MCM or One #4 WG to 600 MCM Two /0 WG to 600 MCM Four 1/0 to 600 MCM Six 1/0 to 600 MCM Twelve /0 to 600 MCM Notes: 1. ll Series 00 switches are furnished with a solid neutral plate (unless switched neutral configuration is specified) and terminal lugs. Specify in catalog number to order a neutral plate on the series 86 switches.. 00 and 0 amp rated switches for use with copper cable only. Refer to paragraph 10.15 of the NEC for additional information.. Use wire rated 75 o C minimum for all power connections. 11
Series 00SE Power Transfer Switch The SCO Service Entrance Power Transfer Switch combines automatic power switching with the necessary disconnecting, grounding, and bonding required for use as service entrance equipment. The power transfer switch meets all National Electrical requirements for service entrance use. Transfer switches generally are installed at facilities that have a single utility feed and a single emergency power source. 600-000 mp Construction SCO Series 00SE products use two types of construction. Products 400 amperes or less, utilize a single enclosure including a service (utility source) disconnect circuit breaker, as well as the power transfer switch, grounding and bonding provisions. Products 600 amperes and above, utilize a multi-section switchboard construction including a service equipment section containing the service (utility source) disconnect circuit breaker, grounding, and bonding provisions. second section contains the power transfer switch. Product Features: Suitable for use as service entrance equipment. Listed to UL 891 (standard for switchboards) for 600-000 amps, sizes and UL 1008 (standard for panel-boards) for 70-400 amps. utomatic Transfer Switch is listed to UL 1008 for total system loads Sizes available from 70-000 amps, 600 VC, 50 or 60 Hz, single or three phase Silver plated copper ground and neutral bus solderless screw type terminals Ground fault trip protection provided on sizes 1000 amps and above vailable with solid or switched neutral 70-400 mp Construction Fig. 16: SCO Series 00 SE Rated 800 amperes Type 1 enclosure with Service Entrance Equipment Fig. 17: SCO Series 00 SE rated 00 amperes in Type 1 enclosure with single source breakers 1 To order an SCO Series 00SE Power Transfer Switch, complete the following catalog number: US + + + 400 + N + 1 + X + C + 11CD + 40 V/60 Product US Notes: 1 Switched Series 00SE Transfer Switch Ordering Information Phase Poles poles, 1Ø poles, Ø mperes Continuous Rating 70, 100, 150, 00 6, 5 6, 50, 400, 600, 800, 1000, 100, 1600, 000 500, 000 Voltage C D E F H J K L M N Q R 115 10 08 0 0 40 80 400 415 440 460 480 575 600 1. Specify neutral code C for 50 and 400 amperes only.. vailable 70-1000 ampacity. Use Type R for 100-000 amp applications.. 115-10 volt available 150-400 amps only. 4. solid neutral is standard on US. 5. For switch sizes 70-5 amperes only. Controller Options 1 Insert X If optional accessories are required Enclosure lank Open Type C Type 1 (Standard) F Type R G Type 4 H Type 4X L Type 1 M Type R N Type 4 Type 4X 6 P Double Door SS Type RX 7,8 R Double Door SS Optional ccessories 11G Programmable Engine Exerciser 14/14 uxiliary Contacts ( sets) 44G Strip Heater w/thermostat 7 Serial Module 7E Connectivity Module 7 Surge Suppressor 6. 00, 5 amp rated switch suitable for use with copper cable only. 7. Type 16 Stainless Steel is standard. It provides an improved reduction in corrosion of salt and some chemicals. It is the preferred choice for marine environments. 8. vailable only on switches rated 100, 000, 600, and 000 mps. Specific Volt & Freq This information is necessary to allow correct control settings prior to shipment
Series 00SE Transfer Switch Dimensions and Shipping Weights UL Type 1 Enclosure 4 Switch Rating mps 70, 100,150, 00, 5 50, 400 600 1, 800 1 1000 1, 100 1 1600 1, 000 1 500 1, 000 1 Phase Poles C C Dimensions, In. (mm) Width Height Depth 6.5 (97) 48.5 (1) 1.5 (7) 6.5 (97) 48.5 (1) 1.5 (7) 6.5 (97) 48.5 (1) 1.5 (7) 6.5 (97) 48.5 (1) 1.5 (7) 6.5 (97) 48.5 (1) 1.5 (7) 6.5 (97) 48.5 (1) 1.5 (7) 6.5 (97) 48.5 (1) 1.5 (7) 6.5 (97) 48.5 (1) 1.5 (7) 8 (965) 91 (11) 8 (711) 8 (965) 91 (11) 8 (711) 8 (965) 91 (11) 8 (711) 8 (965) 91 (11) 8 (711) 8 (965) 91 (11) 48 (118) 8 (965) 91 (11) 48 (118) 8 (965) 91 (11) 48 (118) 8 (965) 91 (11) 48 (118) 8 (965) 91 (11) 48 (118) 8 (965) 91 (11) 48 (118) 8 (965) 91 (11) 7 (189) 8 (965) 91 (11) 7 (189) pprox. Shipping Weight Lb. (kg) 400 (185) 408 (188) 408 (188) 416 (19) 400 (185) 408 (188) 408 (188) 416 (19) 800 (70) 80 (78) 80 (78) 846 (90) 1085 (501) 1105 (510) 1105 (510) 114 (5) 590 (1198) 640 (118) 4590 (118) 4655 (148) UL Type R Enclosure 4 Switch Rating mps 70, 100,150, 00, 5 must specify 50, 400 600 1, 800 1 1000 1, 100 1 1600 1, 000 1 500 1, 000 1 Phase Poles C C Notes: 1. Unit is designed for top and bottom cable entry for all services and load.. Enclosures for 600 000 amps are freestanding.. When temperatures below F can be experienced, special precautions should be taken, such as the inclusion of strip heaters, to prevent condensation and freezing of this condensation. This is Dimensions, In. (mm) Width Height Depth 6(914) 48(119) 16 (406) 6(914) 48(119) 16 (406) 6(914) 48(119) 16 (406) 6(914) 48(119) 16 (406) 6(914) 48(119) 16 (406) 6(914) 48(119) 16 (406) 6(914) 48(119) 16 (406) 6(914) 48(119) 16 (406) 95.5(46) 4(864) 95.5(46) 4(864) 95.5(46) 4(864) 95.5(46) 4(864) 95.5(46) 6(1575) 95.5(46) 6(1575) 95.5(46) 6(1575) 95.5(46) 6(1575) 95.5(46) 6(1575) 95.5(46) 6(1575) 96(48) 85(159) 96(48) 85(159) pprox. Shipping Weight Lb. (kg) 180 (8) 188 (87) 188 (87) 196 (90) 440 (0) 448 (07) 448 (07) 485 (5) 990 (458) 1010 (467) 1010 (467) 106 (479) 105 (604) 15 (61) 15 (61) 154 (66) 890 (17) 940 (160) 550 (474) 5415 (504) particularly important when environmental enclosures (Type R, 4 & 1) are ordered for installation outdoors. See Optional ccessories page for space heater options (acc. 44G). 4. Dimensional data is approximate and subject to change. Certified dimensions available upon request. Extended Warranties for Series 00SE Transfer Switches Catalog No. EXW00SE EXW00SE 4EXW00SE 5EXW00SE Description Two-Year Extended Warranty (Parts & Labor) Three-Year Extended Warranty (Parts & Labor) Four-Year Extended Warranty (Parts & Labor) Five-Year Extended Warranty (Parts & Labor) Series 00SE IC Rating Switch Rating 70, 100, 150, 00, 5 50, 400 600 800, 1000,100, 1600, 000 500, 000 IC Rating 5,000 5,000 50,000 65,000 100,000 Voltage 480 480 480 480 480 Series 00SE External Power Connections Sizes UL-Listed Solderless Screw-Type Terminals Switch Rating 70, 100, 150, 00 *, 5 * 50, 400 600 800, 1000, 100 1600, 000 500 000 Ranges of L-CU Wire Sizes (Unless Specified Copper Only) One #14 to 4/0 WG Two 1/0 WG to 50 MCM or One #4 WG to 600 MCM Two 1/0 WG to 600 MCM Four 1/0 to 600 MCM Six 1/0 to 600 MCM Twelve /0 to 600 MCM Twelve /0 to 600 MCM Note: ll Series 00SE switches are furnished with a solid neutral plate (unless switched neutral configuration is specified) and terminal lugs. * 00 and 5 amp rated switch for use with copper cable only. 1
Series 00L Power Transfer Load Center Conventional double throw transfer switch configuration utomatic Transfer Switch is listed to UL1008, the standard for Transfer Switch Equipment, and meets NFP 110 for Emergency and Standby Power Systems and the National Electrical (NEC) rticles 700, 701, and 70. lso certified to CS. No. 178 Rated up to 40VC, 00, or 400 amps vailable in Type 1 indoor, or Type R secure aluminum outdoor enclosure Reliable and field proven single solenoid operating mechanism Programmable microprocessor controller with flush mounted control and display panel LED indicators for switch position and source availability Engine exerciser for weekly automatic testing of engine generator set with or without load Two auxiliary contacts, one contact closed when switch is in normal position and one contact closed when switch is in emergency position Suitable as service entrance equipment, includes main circuit breaker overcurrent protection on the normal source, and circuit breaker disconnect device on emergency Includes a UL 67 Listed 4 position Square - D panelboard load center Local/remote communications capability for interfacing with SCO POWERQUEST communication products 14 SCO 00L utomatic Power Transfer Load Center shown with optional quick connect Cam - Loc assembly and bottom Telco cabinet section (in type R secure aluminum enclosure) Short Circuit Ratings 00 Mains: k at 40vac (Main circuit breaker (Normal & Emergency) Square D circuit breakers rated / pole, 00) Note: If a generator input receptacle is supplied for a portable generator then the ratings are as follows: Normal Source k at 40 vac (Utility Main Disconnect circuit breaker) Emergency Source # (Permanent Generator Input circuit breaker) 10k at 40vac Emergency Source -#1 (Portable Generator Input circuit breaker) 5k at 40vac 400 Mains: 4k at 40vac. (Main circuit breaker (Normal & Emergency) Square D circuit breakers rated / pole, 400) Panelboard: Square D 5/400 series rated 4 circuit panelboard single/three phase with 100% rated neutral, accepts bolt on or plug in branch devices.
00L Power Transfer Switch Ordering Information 00 Product 00 + L4 + + 00 + F + 5 + X + C Load Center 4 = 4 Space Poles poles, 1Ø poles, Ø mperes Continuous Rating 00 400 C F Voltage 08 40 Controller Options Enclosure Type R (Outdoor) + 7TL1 Optional ccessories 11G - Programmable 1 Insert X Type 1 C if optional (Standard) Engine Exerciser accessories are required M 14/14 - uxiliary Contacts ( Sets) 1 7P - Generator Receptacle 44 - Strip Heater w/thermostat + 40V 60Hz Specific Voltage & Freq This Information is necessary to allow correct settings prior to shipment 7 -Serial Module 7E - Connectivity Module 7 - Surge Suppression (TVSS) 85L - Power Manager 117I - Interlock reaker for Portable Generator 18T - Telco Cabinet 10MG - Cam Loc 1. vailable on 00L, Power Transfer Load Center only. (two sets are standard) for 7000L Series.. vailable for Type R enclosure only, rated 00 mps. Not available for 400 mp. Sizes UL-Listed Solderless Screw-Type Terminals Switch Rating (mps) 00 400 Max # of Conductors per Terminal One One Two Ranges of L-CU Wire Sizes (Unless Specified Copper Only) # 4 WG to 50 MCM # 1 WG to 600 MCM # 1 WG to 50 MCM Dimensions for UL Type 1 and R d Enclosure Switch Rating mps Enclosed UL Type1 00 Phase Poles, Dimensions, In. (mm) Width Height Depth 0(76) 78(1981) 6(15) pprox. Shipping Weight Lb. (kg) 50(115) 400, 8(965) 80(0) 7-1/4(184) 00(18) Enclosed UL TypeR luminum 00 1, 6(914) 5(146) 11(79) 05(141) 400, 8(965) 84(14) 11-1/4(86) 5(149) Note: 1. dd 0 inches to the height of the type R enclosure if accessory 18T, Telco cabinet is required. Extended Warranties for Series 00L Power Transfer Center Switches Catalog No. EXW00L EXW00L 4EXW00L 5EXW00L Description Two-Year Extended Warranty (Parts & Labor) Total years Three-Year Extended Warranty (Parts & Labor) Total years Four-Year Extended Warranty (Parts & Labor) Total 4 years Five-Year Extended Warranty (Parts & Labor) Total 5 years Field Conversion Kits for Series 00L Transfer Switches Kit No. Description K74-001 Single Phase Surge Suppression 40v/10v (cc. 7V*1) K74-00 Three Phase Surge Suppression 09v/10v (cc. 7V*) Note: 1. Consult SCO for Type R secure enclosures 15
16
17
18 PowerQuest 5700 Critical Power Management System
19
Emerson Network Power. The global leader in enabling usiness-critical Continuity TM. C Power Connectivity DC Power Embedded Computing Embedded Power Infrastructure Management & Monitoring Outside Plant Power Switching & Controls Precision Cooling EmersonNetworkPower.com Racks & Integrated Cabinets Services Surge Protection Emerson Network Power and the Emerson Network Power logo are trademarks and service marks of Emerson Electric Co. 01 Emerson Electric Co. Publication 1195 R14.5 pril, 01 Printed in the U.S..