Articulating TV/Monitor Clamp/Grommet Desk Mount Model: DE640S (Hydro Series) Instruction Manual Images may be different from actual product Disclaimer It is Dyconn s intention to have all the correct information present within this manual. Although we try our best, Dyconn makes no claim that the information comprised herein covers all conditions or details in connection with installation or use of this product. Dyconn assumes no responsibility for accuracy or adequacy of information comprised in this document. The information comprised here is subject to change without notice or obligation of any kind. This warning informs you of the possibilities of personal injury or damage to equipment if you do not follow the corresponding instructions. It is the installer's responsibility to make sure all components are properly assembled and installed using the instruction manual provided. Using improper screws or screw sizes may damage your display. If spacers are required, be sure to use screws of the correct size. Proper screws used will easily and completely thread into the display mounting holes. Inadequate thread engagement in the display may cause display to fall. It is the installer s responsibility to make sure the combined weight of all components does not exceed the weight capacity of 17.6lbs (8kg). Exceeding weight capacity can result in severe personal injury or damage to equipment. Allowing any part of your component cables to be caught between movable parts can result in serious personal injury or damage to equipment. The Articulating Arm will spring upward and may cause personal injury or equipment damage when the weight of the monitor is removed. Secure arm by lifting the arm to full upright position when monitor is removed. Page 2
Please read the following Instructions before installing: Verify that all parts are included. Do not install if the products or hardware are damaged. Not all hardware included will be used. Please contact a qualified installer. This product contains moving parts. Use with caution. Determine approximate location for mounting and be sure to consider the display size, extension, height adjustment and pitch/roll requirements. This product contains small items; please keep these items away from children. Do not exceed the maximum weight capacity for this product. Exceeding the weight capacity can result in serious personal injury or damage to equipment! The table being used for installation must be stable and strong enough to support the DE640S mount and display. Specifications Weight Capacity Suits LCD Flat Panel Displays Length Retracted Length Extended Arm Lift Range Vertical Height Range on Pole 17.6lbs (8kg) 12-24 (305mm-610mm) 2.95" (75mm) 22.72" (577mm) +/- 40 11.8"(300mm) 12.9" (327mm) Mounting surface thickness Desk Clamp: 2.95" (75mm) Grommet: 2 (50.8mm) Tilt +/-90 Swivel +/-90 Display Rotation 360 Page 3
Product Dimension Page 4
Parts List Page 5
Installation Instructions 1) Place the Gasket Cushions to the base of the Desk Clamp. 2) Place the Desk Clamp on the edge of the desk. Adjust the screw on the Desk Clamp to ensure that pressure plate is pressed flat onto the desk surface. Tighten the hex screw using the Allen Wrench 8mm until the Desk Clamp is secure. Page 6
1) Remove the Desk Clamp and attach the Grommet Plate. 2) Place the Gasket Cushions onto Grommet Plate. Page 7
3) Place the Grommet mount over the cable management hole. Adjust the screw until the pressure plate is pressed flat onto the desk surface. Using the Allen Wrench 8mm, tighten the hex screw until the Grommet mount is secured in place. Page 8
1) Place the mounting head onto the back of display. Align the holes with the holes on the back of the monitor. Select the proper length of screws that suit your monitor s specifications and tighten the screws with a Philips Screwdriver until the mount head is firmly attached to the display. Do not over tighten the screws. Stop immediately if you encounter any resistance 2) Use Spacer for displays with recessed mounting holes. 1) Hold the top of collar and rotate the lower part counterclockwise to loosen. Adjust the collar along the pole to desired location. Tighten in a clockwise direction to secure position. Page 9
1) Attach the assembled LCD Arm and display down onto the pole. If necessary, tighten the collar to secure position. Follow by tightening the hex grub screw using the Allen Wrench 2.5mm until the assembly is firmly in place. Page 10
1) Ensure the assembled DE640S mount is fully extended. Be sure to leave enough slack in the cables to allow for movement of the arms so that they are not stretched or pulled out when the display is moved. 2) Feed the cables through the cable entry slot on the underside of the arm. 3) Attach the Cable Clip to secure cables to the pole. Page 11
1) Adjust the screw on top of the arm using the Allen Wrench 4mm to adjust the amount of resistance in the arm range of +/- 40 degrees. Page 12
1) Adjust the screws to suit your desired display tilt and swivel of +/- 90 degrees and also display orientation of 360 degrees. Page 13
DYCONN PRODUCT WARRANTY To obtain warranty service, contact Dyconn customer service at (855) 239-2666 or visit www.dyconn.com. Dyconn disclaims any liability for modification, improper installations, or installations over specified weight range. Dyconn will not be liable for any damages arising out of the use of, or inability to use of Dyconn products. Warranty specification is subject to change without prior notice. Page 14