Testking.200-001.139q Number: 200-001 Passing Score: 800 Time Limit: 120 min File Version: 7.8 Cisco 200-001 Implementing Cisco Video Network Devices Great dump, passed with 95%. I agree with you 100% will indeed allow you to pass. Majority of the material in books you will not find on the exam, the questions on the exam are so specific. This is Updated dump. I selected it just because of the course material they gave in its packages and also the price was affordable for everyone. Thanks a lot for the effort you all are putting in getting us certified. Sections 1. Video Concepts 2. Endpoint Configuration 3. Troubleshooting and Support
4. Conferencing Concepts 5. Simulation Questions
Exam A QUESTION 1 Which of these involves combining visual elements from separate sources into a single image? A. Interlacing B. Compositing C. Video conferencing D. Interleaving Correct Answer: B Section: Video Concepts /Reference: answer is right. QUESTION 2 Which two Cisco TelePresence systems would be appropriate for an executive personal office? (Choose two.) A. Cisco Jabber B. Cisco IP Video Phone E20 C. Cisco TelePresence EX Series D. Cisco Jabber Video for TelePresence E. Cisco TelePresence System 500 Correct Answer: CE Section: Endpoint Configuration /Reference: Best answer. QUESTION 3 Refer to the exhibit.
You have just finished installing a 65-inch dual profile system in a multipurpose room. After powering up the entire system, only one display is used. Using the information in the exhibit, why is the second display not displaying anything from the system? A. The Cisco TelePresence profile systems do not support dual display. B. The display is not powered on. C. The dual display option key has not been input into the codec. D. The codec has the appropriate option keys installed, so either the display is not cabled correctly, the codec is configured incorrectly, or there is no input being sent to the display. Correct Answer: D Section: Endpoint Configuration
/Reference: : QUESTION 4 Which DHCP option is used by video endpoints to locate the Cisco Communications Manager TFTP server to download the endpoints configuration? A. option 43 Real 26 B. option 82 C. option 150 D. option 176 E. option 242 Correct Answer: C Section: Endpoint Configuration /Reference: : QUESTION 5 Refer to the exhibit. You are troubleshooting an issue involving Cisco SX20 and EX90. You log in to the codec GUI to make test calls. From which tab do you make test calls via the
codec GUI? A. Diagnostics tab B. Maintenance tab C. Configuration tab D. Call Control tab E. Home tab F. Calls can be made only via the CLI. Correct Answer: D Section: Endpoint Configuration /Reference: proper answer. QUESTION 6 A customer reports that in a CTS1300 room, a microphone switches to a segment that has no one talking. Which step is first in the troubleshooting process? A. Replace the microphones to stop phantom switching. B. Reseat the microphone cables. C. Recalibrate the microphones. D. Reboot the codec. E. Replace the audio expansion box because the microphones connect to an AV expansion box. Real 27 Correct Answer: C Section: Endpoint Configuration /Reference: : QUESTION 7 On a Cisco EX90, if the camera is tilted downward toward the base of the unit, how is the image transmitted? A. black and white
B. rotated 180 degrees C. with a 2.5x zoom D. Video transmission is disabled. Correct Answer: B Section: Endpoint Configuration /Reference: answer is valid. QUESTION 8 Your customer reports that new A/V equipment that plays movies cannot be displayed on their Cisco TelePresence endpoints. This A/V equipment is connected to the Cisco TelePresence codec via an HDMI cable. However, older A/V gear that uses composite cables is able to display content. What is most likely the cause of this issue? A. The composite cables are faulty. B. TIP negotiation is failing between the A/V gear and the Cisco TelePresence device. C. The A/V gear is using HDCP to prevent illegal copying. D. The operating system for the A/V gear is not compatible with the operating system of the Cisco TelePresence device. Correct Answer: C Section: Endpoint Configuration /Reference: : QUESTION 9 Refer to the exhibit.
Under which tab can the log file for the endpoint be found? A. Diagnostics B. Configuration C. Call Control D. Maintenance Correct Answer: A Section: Troubleshooting and Support /Reference: : QUESTION 10 Refer to the exhibit.
Under which tab can the registration status for the endpoint be found? Real 33 A. Diagnostics B. Configuration C. Call Control D. Maintenance Correct Answer: A Section: Troubleshooting and Support /Reference: answer is updated. QUESTION 11 While performing a password recovery on a Cisco TelePresence endpoint, what is the maximum amount of time for input to be received by the device before the system exits the password recovery mode? A. 15 seconds B. 20 seconds
C. 30 seconds D. 40 seconds E. 60 seconds Correct Answer: E Section: Troubleshooting and Support /Reference: : QUESTION 12 Which two of these are required in order to complete the password recovery of a Cisco TelePresence System endpoint? (Choose two.) A. must have FTP enabled on the endpoint B. must have SSH enabled on the endpoint C. must have the security question answer for the endpoint D. must be in the same room as the main display E. must have SFTP enabled on the endpoint F. must call Cisco TAC for the security code Correct Answer: BD Section: Troubleshooting and Support /Reference: : Real 34 QUESTION 13 Which three of these are functions of the Cisco TelePresence Management Suite? (Choose three.) A. automatic software update and release keys B. intelligent call routing engine C. provisioning a Cisco TelePresence System endpoint D. tracing SIP and H.323 calls
E. managing phonebooks for endpoints that are registered to the Cisco Unified Cisco Unified Communications Manager F. rebooting endpoints that are registered to the Cisco TelePresence Video Communications Server Correct Answer: ABF Section: Troubleshooting and Support /Reference: : QUESTION 14 Refer to the exhibit.
When the administrator clicks the ticket number of any of the open tickets, which two actions are presented to the administrator? (Choose two.) A. ignore ticket B. acknowledge ticket C. delete ticket D. close ticket Real 35 E. escalate ticket
Correct Answer: AB Section: Troubleshooting and Support /Reference: : QUESTION 15 Refer to the exhibit.
Which system tab can be used to add video infrastructure devices and endpoints? A. Navigator B. System Overview C. Configuration Templates
D. Provisioning E. Administrative Tools Correct Answer: A Section: Troubleshooting and Support /Reference: : QUESTION 16 You have been informed from the field that a new Cisco TelePresence video endpoint has been deployed with an IPv4 address of 172.28.254.45. You need to check for connectivity from the Cisco Unified Communications Manager server. Which command should be entered to check for Real 36 network connectivity? A. utils network traceroute newsystem.domain254.local B. utils network ping 172.28.254.45 C. ping 172.28.254.45 D. traceroute 172.28.255.255 E. utils network host cucm.osl147.local Correct Answer: B Section: Troubleshooting and Support /Reference: absolutely right answer. QUESTION 17 Refer to the exhibit. Real 37
The screenshots show outputs from the xstatus of a Cisco TelePresence endpoint and the VCS registrations. What are the protocol and direction of the call, the called party, and the transmit rate of the call? A. h.323, incoming, 5919*2345, 1152 Kb/s B. h.323, outgoing, 5919*2345, 1152 Kb/s C. h.323, incoming, 5919*2345, 768 Kb/s D. sip, incoming, 5919*2345, 768 Kb/s E. sip, outgoing, 5919*2345, 768 Kb/s Real 38 Correct Answer: B Section: Troubleshooting and Support /Reference: : QUESTION 18 Which CLI command can be used to reset the Cisco TelePresence System 500-32 personal video system to a factory condition? A. utils factory reset 2 B. utils system factory init C. xcommand defaultvalues set level: 2 D. xconfiguration default factory E. utils reset factory F. xcommand SystemUnit FactoryReset Correct Answer: B Section: Troubleshooting and Support /Reference: : QUESTION 19 Refer to the exhibit.
Real 39
Which two of these can cause the phone status error icon that is shown in the exhibit? (Choose Real 40 two.) A. The Cisco Unified Communications Manager IM and Presence Service is not available. B. The username and password in Cisco Jabber phone services are misconfigured. C. The Cisco Jabber initial audio and video settings need to be set. D. There is no DN configured for the Cisco Unified Client Services Framework in Cisco Unified Communications Manager. E. The Cisco Jabber does not have the correct phone button template and hence cannot register to the Cisco Unified Communications Manager. F. The called user presence status is unknown. Correct Answer: BD Section: Troubleshooting and Support /Reference: : QUESTION 20 Which two of these can cause registration problems for a Cisco TelePresence Codec C40 endpoint running in H.323 mode? (Choose two.) A. The IP default gateway address is incorrect for the endpoint. B. The H.323 license stack is not added to the endpoint. C. The MAC address for the endpoint has not been added to the Cisco TelePresence VCS. D. The E.164 H323Alias has not been configured on the endpoint. E. The URI address has not been configured on the endpoint. Correct Answer: AD Section: Troubleshooting and Support /Reference: : QUESTION 21 What is the main difference between Cisco Jabber and Cisco Jabber Video for TelePresence?
A. Cisco Jabber registers to the Cisco Unified Communications Manager, whereas Cisco Jabber Video for TelePresence registers to the VCS. B. Cisco Jabber Video for TelePresence registers to Cisco Unified Communications Manager, whereas Cisco Jabber registers to the VCS. C. Cisco Jabber has no video calling capabilities, whereas Cisco Jabber Video for TelePresence has video capabilities. D. Cisco Jabber has no presence capabilities, whereas Cisco Jabber Video for TelePresence has presence capabilities. Real 41 E. There is no difference between Cisco Jabber and Cisco Jabber Video for TelePresence. They should not coexist in the same network. Correct Answer: A Section: Troubleshooting and Support /Reference: ALL right. QUESTION 22 On a video endpoint running TC software, which two SIP settings are the minimum needed to register the endpoint to a Cisco VCS? (Choose two.) A. URI B. loginname C. password D. E.164 address E. gatekeeper F. proxy address G. domain Correct Answer: AF Section: Troubleshooting and Support /Reference: : QUESTION 23 Refer to the exhibit.
Users in a Cisco TelePresence room report audio and video quality issues. You have been asked to troubleshoot the issue. You log in to the endpoint GUI and check telephony settings. Which Real 42 option would you recommend to resolve the issue? A. Audio/video quality issues are generally due to low bandwidth. Contact your carrier to increase the bandwidth. B. "DSCP For TelePresence" is not correct. Configure the correct value via codec GUI. C. "DSCP For Audio" is not correct. Configure the correct value via codec GUI. D. DSCP values are correct. Check the QoS configuration on the router. E. The "DSCP For TelePresence" and "DSCP For Audio" values are not correct. Configure the correct value in codec GUI. F. The "DSCP For TelePresence" and "DSCP For Audio" values are not correct. Configure the correct value in the Cisco Unified Communications Manager service parameter. Correct Answer: F Section: Troubleshooting and Support /Reference: : QUESTION 24 When a user attempts to sign in with a Jabber Video for Cisco TelePresence client, which SIP message is the first that is sent? A. INFO B. NOTIFY
C. REGISTER D. SUBSCRIBE Correct Answer: D Section: Troubleshooting and Support /Reference: : QUESTION 25 Your customer has an EX60 at a home-office that is doing direct H.323 dialing. When they place calls to remote sites, they report that they cannot see video or hear audio from the remote sites. What is most likely the cause of this issue? A. NAT mode is not configured on the EX60. B. The HDMI cable that connects the EX60 to the monitor is not plugged in. C. A username and password must be configured on the EX60. D. QoS is not properly configured on the EX60. Correct Answer: A Section: Troubleshooting and Support /Reference: Real 43 : QUESTION 26 A new Cisco DX650 is not registering in the Cisco Communications Manager running version 9.1.2. The latest device package and firmware was uploaded on all Cisco Communications Manager servers in the cluster. What is most likely the cause of this issue? A. A cluster-wide reboot is needed to enable the functionality. B. You must restart the TFTP server. C. The firmware in the Cisco Unified Communications Manager is incorrect. D. The software version in the Cisco Unified Communications Manager is incorrect.
Correct Answer: A Section: Troubleshooting and Support /Reference: valid answer. QUESTION 27 In which two locations can you find registration information for a video endpoint? (Choose two.) A. from the endpoint touch panel on the Settings > System Information screen B. from the endpoint web interface on the Home screen C. from the Cisco VCS in the Status > System screen D. from the Cisco TMS on the Systems > Provisioning screen Correct Answer: AB Section: Troubleshooting and Support /Reference: : QUESTION 28 Refer to the exhibit. Real 44 Which option enables you to create a system snapshot? A. Status B. System C. Configuration
D. Applications E. Users F. Maintenance Correct Answer: F Section: Troubleshooting and Support /Reference: : QUESTION 29 In the web interface for a Cisco VCS or Expressway running X8.2, which page allows you to enable and download logs that include the xconfiguration, xstatus, DEBUG level network logs, and packet captures of both network interfaces? A. Maintenance > Diagnostics > Diagnostic Logging B. Maintenance > Diagnostics > System Snapshot C. Status > Logs > Event Log D. Status > Logs > Configuration Log Correct Answer: A Section: Troubleshooting and Support /Reference: : QUESTION 30 Which two methods can you use to update the configuration automatically using the persistent configuration settings for an endpoint using TMS? (Choose two.) A. Manually refresh the endpoint configuration for the Cisco TMS provisioning page. B. Cisco TMS can be scheduled to push a template to endpoints. C. User can edit the configuration manually for the endpoint from Cisco TMS. D. The endpoint can receive the persistent settings from Cisco TMS after each reboot. E. The endpoint can download the configuration via DHCP option 150. Correct Answer: BD Section: Troubleshooting and Support
/Reference: : Real 45 QUESTION 31 Refer to the exhibit. Which option performs a factory reset of a Cisco TelePresence System endpoint? A. Configuration > System Settings
B. Configuration > Security Settings C. Troubleshooting > Hardware setup D. Monitoring E. Troubleshooting > Configuration Issues F. Troubleshooting > System Restart G. A Cisco TelePresence System endpoint can be reset only via CLI. Correct Answer: E Section: Troubleshooting and Support /Reference: : QUESTION 32 Your customer reports that they have had unwanted calls routing from their Cisco VCS Expressway to their ISDN gateway. Which way is recommended to prevent these calls? A. Configure a Registration Deny List on the Cisco VCS Expressway. B. Configure a Registration Allow List on the Cisco VCS Expressway. C. Implement a CPL on the Cisco VCS Control. D. Implement a CPL on the Cisco VCS Expressway. Correct Answer: D Section: Troubleshooting and Support /Reference: :
QUESTION 33 Which command returns the Cisco VCS to its factory default settings? A. write erase B. factory-default C. xcommand SystemUnit FactoryReset Confirm: Yes D. utils SystemUnit FactoryReset Confim: Yes E. factory-reset Correct Answer: E Section: Troubleshooting and Support /Reference: definite answer. QUESTION 34 You are troubleshooting an issue and you need to connect to presentation codec via CLI. Which CLI command allows you to connect to the presentation codec? A. utils connect presentation B. utils system presentation C. utils presentation connect D. utils presentation system E. set system presentation Correct Answer: B Section: Troubleshooting and Support /Reference: : QUESTION 35 Real 47 Which command causes a Cisco VCS to drop registrations for currently registered endpoints only if they are not currently in a call? A. xconfiguration SystemUnit Maintenance Mode: Off B. xconfiguration SystemUnit Maintenance Mode: On
C. xconfiguration Zones LocalZone DefaultSubZone Registrations: "Deny" D. xconfiguration Registration RestrictionPolicy Mode: "DenyList" Correct Answer: B Section: Troubleshooting and Support /Reference: : QUESTION 36 Refer to the exhibit. Which CLI command should be run to resolve these alarms on a Cisco VCS? A. xcommand DefaultValuesSet B. xconfiguration DefaultLinksAdd C. xcommand DefaultLinksAdd D. xconfiguration DefaultValuesSet Correct Answer: C Section: Troubleshooting and Support /Reference: :
QUESTION 37 Which option describes how to configure SNMP settings on a CTS/TX endpoint? A. can be configured only via codec CLI B. can be configured only via codec GUI C. can be configured only in a device profile in Cisco Unified Communications Manager D. can be configured either via codec GUI or codec CLI Real 48 E. can be configured in codec GUI, codec CLI, or device profile in Cisco Unified Communications Manager Correct Answer: C Section: Troubleshooting and Support /Reference: : QUESTION 38 Refer to the exhibit. When this alarm is seen, what is the maximum number of registrations that a Cisco VCS can support? A. 2500 B. 50 C. 3 D. 0 Correct Answer: C Section: Troubleshooting and Support /Reference: : QUESTION 39
Refer to the exhibit. Real 49 Which Cisco Prime Collaboration capabilities are shown? A. Endpoint and system inventory reporting B. Proactive monitoring and alerts for video endpoint faults C. End-to-end network path troubleshooting D. Real-time monitoring and alerts for video endpoint faults E. Dashboard view of overall voice and video network health
Correct Answer: E Section: Troubleshooting and Support /Reference: QUESTION 40 Which three Cisco TelePresence multipoint media conferencing platforms can utilize Cisco Unified Communications Manager for call control? (Choose three.) A. Cisco TelePresence Multipoint Control Unit B. Cisco TelePresence System 500-32 C. Cisco TelePresence Server D. Cisco TelePresence Media Bridge Server E. Cisco TelePresence Multipoint Switch F. Cisco TelePresence SX20 Correct Answer: ACE Section: Conferencing Concepts /Reference: Real 50 : QUESTION 41 Which two layout or switching modes are supported with the Cisco TelePresence Multipoint Switch? (Choose two.) A. enhanced continuous presence B. active speaker switching C. continuous presence D. speaker switching E. room switching F. active continuous presence Correct Answer: DE Section: Conferencing Concepts
/Reference: : QUESTION 42 Which Cisco TelePresence Multipoint Control Unit Layout view mode gives prominence to one conference participant over the other conference participants while still allowing conference participants to view multiple participants at the same time? A. Enhanced continuous presence B. Active speaker C. Continuous presence D. Room switching E. Speaker switching Correct Answer: A Section: Conferencing Concepts /Reference: : QUESTION 43 Which two systems would be an appropriate solution for a traveling employee? (Choose two.) A. Cisco Jabber B. Cisco C-Series codec Real 51 C. Cisco TelePresence EX Series D. Cisco Jabber Video for TelePresence E. Cisco TelePresence System 500 F. Cisco IP Video Phone E20 Correct Answer: AD Section: Conferencing Concepts /Reference:
: QUESTION 44 What are the best practices for maintaining a high-quality video call regarding latency, jitter, and packet loss? A. 20-ms one-way delay, no jitter, no packet loss B. less than 150-ms one-way delay, 30-ms jitter, less than 3 percent packet loss C. 150- to 400-ms one-way delay, 50-ms jitter, 5 percent packet loss D. 500-ms one-way delay, 50-ms jitter, 5 percent packet loss Correct Answer: B Section: Conferencing Concepts /Reference: : QUESTION 45 An important Cisco TelePresence video multipoint call is in progress and you are getting complaints of pixilation of the video and poor audio quality on one of the involved systems. Which page would be a good place to start for troubleshooting the issue on the affected endpoint? A. B. Real 52
C.
D. A. Option A B. Option B C. Option C D. Option D Correct Answer: A Section: Conferencing Concepts /Reference: : QUESTION 46 Which two of these support an ad-hoc conference call? (Choose two.) A. Cisco TelePresence Multiway with Cisco TelePresence Multipoint Control Unit and Cisco TelePresence Video Communications Server Real 53 B. using the Cisco TelePresence Management Suite Scheduler to schedule a conference call to start in 5 minutes C. using the Booking tab in the Cisco TelePresence Management Suite to configure a new conference D. using the tab Administrative Tools > Configuration > Conference Settings in the Cisco TelePresence Management Suite E. pressing the conference button on a Cisco Unified IP Phone 8941 to conference in a third call
Correct Answer: AE Section: Conferencing Concepts /Reference: : QUESTION 47 Refer to the exhibit.
Which configuration element can be used to specify the Multiway address that can be used by the endpoint to initiate Multiway calls? A. Conference 1 B. NetworkServices Real 54 C. Provisioning D. SIP Profile 1 E. Video Correct Answer: B Section: Conferencing Concepts /Reference: : QUESTION 48 You have been informed from the field that a new Cisco TelePresence video endpoint has been deployed with an IPv4 address of 172.28.254.45. Which three devices could you use to see if the endpoint is registered and available for a call? (Choose three.) A. Cisco Unified Communications Manager server B. Cisco Gigaswitch Router C. Cisco TelePresence Manager Suite server D. Active Directory server E. Cisco TelePresence Video Communication Server F. Cisco 3250 Layer 2/3 Switch Correct Answer: ACE Section: Conferencing Concepts /Reference: : QUESTION 49 Refer to the exhibit.
Which tab can be used in order to check the call statistics for the Cisco TelePresence Codec C60? A. Diagnostics B. Configuration C. Call Control D. Maintenance E. The GUI cannot be used to view call statistics. Real 55 Correct Answer: C Section: Conferencing Concepts /Reference: : QUESTION 50 Cisco TelePresence Video Communication Servers can be clustered to provide resiliency in the enterprise. What is the maximum number of cluster members? A. 2 B. 3 C. 6 D. 7 E. 15 Correct Answer: C Section: Conferencing Concepts /Reference: :
QUESTION 51 Which component of the Cisco TelePresence multipoint media infrastructure is intended for use only with non-immersive endpoints? A. Cisco TelePresence Server B. Cisco TelePresence System 500-32 C. Cisco TelePresence Multipoint Switch D. Cisco TelePresence Multipoint Control Unit Correct Answer: D Section: Conferencing Concepts /Reference: : QUESTION 52 Which Cisco TelePresence endpoint uses only Cisco Unified Communications Manager as its call control device? A. SX20 B. Cisco TelePresence System 500-32 C. EX90 Real 56 D. C60 E. Video Communication Server Correct Answer: B Section: Conferencing Concepts /Reference: : QUESTION 53 When manual discovery is used to register a Cisco TelePresence endpoint to a VCS via SIP, which two pieces of information are required to be configured on the endpoint for registration to occur, assuming that Cisco TMS and DNS are not being used? (Choose two.) A. option 150
B. SIP URI C. proxy address D. H.323 alias E. external manager address F. RTP ports Correct Answer: BC Section: Conferencing Concepts /Reference: : QUESTION 54 Which three of these are valid ways to initially configure a C-Series codec in a network where DHCP is not used? (Choose three.) A. Tandberg Remote Control V B. secure copy program C. CLI using a console cable D. touchscreen interface E. secure web browser F. Telnet Correct Answer: ACD Section: Conferencing Concepts /Reference: : QUESTION 55 Real 57 When dialing, in a format that is consistent for all users of a system, a user who has multiple TelePresence video devices associated, what are the three minimum requirements that must be configured for the user to be able to receive video calls? (Choose three.) A. The Active Directory server must be installed. B. Ensure that the Cisco TelePresence Video Communications Server has the FindMe option key installed.
C. Ensure that FindMe is set to on. D. The NTP server must be set up. E. The Cisco TelePresence Management Suite must be installed. Correct Answer: BCE Section: Conferencing Concepts /Reference: : QUESTION 56 A user wants to use the One Button to Push feature on a Cisco TelePresence System 500-32 video endpoint. Which configuration tool should be used to allow the One Button to Push feature to work? A. Cisco Unified Communications Manager server, phones, devices, One Button to Push B. Cisco Gigaswitch Router, Call Manager Express, One Button to Push C. Cisco TelePresence Manager Suite server, new conference, set Conference type to One Button to Push D. Active Directory server, users, new conference, One Button to Push E. Cisco TelePresence Video Communication Server, new conference, calls, One Button to Push Correct Answer: C Section: Conferencing Concepts /Reference: : QUESTION 57 Which configuration is needed in order for Cisco Jabber Video for TelePresence to initiate Multiway calls? A. Configure the Multiway address under Video Settings in the Cisco Jabber Video for TelePresence client. B. Configure the Mutliway URI address under TelePresence Management Suite > Systems > Provisioning > Users > Configuration Template. C. Configure the Mutliway URI address under Cisco TelePresence Video Communications Server Real 58 > Applications > Cisco Jabber Video for TelePresence. D. The Cisco Jabber Video for TelePresence only supports Multisite calls, which is enabled by default. Correct Answer: B
Section: Conferencing Concepts /Reference: : QUESTION 58 What is the correct order of steps to schedule a One Button to Push conference call between a Cisco TelePresence System 500 and a Cisco TelePresence Codec C40? A. Configure the One Button to Push field under device configuration for the Cisco TelePresence System 500 and Codec C40. B. Configure One Button to Push under Cisco TelePresence Video Communications Server > Applications > OBTP Configuration. C. Configure a new conference under Cisco TelePresence Management Suite > Booking New Conference > Type. D. The One Button to Push feature cannot be configured without a scheduling plug-in application such as Microsoft Outlook. E. Configure the Scheduler tool in the Cisco TelePresence Management Suite. Correct Answer: C Section: Conferencing Concepts /Reference: : QUESTION 59 Which conference types can occur at anytime without the need for the conference to be scheduled, and can be created as permanent conferences? A. ad hoc conferences B. auto-dialed participants C. Multiway conferences D. scheduled conferences E. rendezvous conferences Correct Answer: E Section: Conferencing Concepts /Reference: :
QUESTION 60 Which three options can initiate scheduled or rendezvous meetings hosted on a Cisco TelePresence Server? (Choose three.) A. video endpoint B. Cisco TMS C. Cisco Unified Communications Manager D. Cisco TelePresence Server E. Cisco VCS F. Cisco TelePresence Manager Correct Answer: ABD Section: Conferencing Concepts /Reference: : QUESTION 61 When placing a Multiway call through a Cisco TelePresence Conductor, which IP address on the Conductor should the call be routed to? A. Rendezvous IP address B. Ad hoc IP address C. Scheduled conference IP address D. Management IP address Correct Answer: A Section: Conferencing Concepts /Reference: Real 64
: QUESTION 62 Which type of conference must be booked through Cisco TMS with a start and end time and a predefined set of participants? A. Ad hoc conference B. Multiway conference C. Auto-dialed participant conference D. Rendezvous conference E. Scheduled conference Correct Answer: E Section: Conferencing Concepts /Reference: : QUESTION 63
Real 65
Real 66
Refer to the Exhibits, in order to create a scheduled or ad-hoc multipoint conference, which two tolls can be used? (Choose two) A. Exhibit A B. Exhibit B C. Exhibit C D. Exhibit D E. Exhibit E Correct Answer: BD Section: Simulation Questions /Reference: :
QUESTION 64 Real 67
Real 68
Refer to the exhibits. An administrator needs to perform a factory reset on a C-Series endpoint. What are two valid ways to accomplish this task? (Choose two.) A. Exhibit A B. Exhibit B C. Exhibit C D. Exhibit D E. Exhibit E Correct Answer: AD Section: Simulation Questions /Reference: : Real 69 QUESTION 65
Real 70
The C-Series endpoint (codec) does not register with the Video Communication Server that is located in a different network. Based on the exhibits, what could be causing the issue? A. The subnet mask on the codec is incorrect. B. The ip address of the codec is incorrect. C. The interface that the codec is in is in the wrong VLAN.
D. The codec did not receive a DHCP address from the DHCP server. Correct Answer: A Section: Simulation Questions /Reference: : QUESTION 66 Real 71
Real 72
Real 73
Real 74
Real 75
Real 76
Real 77 When the Cisco Jabber usertries to call extension 3501, Cisco Jabber never places the call No errors or messages are seen and no reordertone is heard. Assuming that the Cisco Jabber calling search space is configured correctly in Cisco Unified Communications Manager, which of these could be causing this issue? A. CTI for the end user must be enabled. B. Cisco Jabber must be reconfigured for desktop mode. C. The username or password is misconfigured in Cisco Jabber. D. The Cisco Jabber Advanced Phone Settings are misconfigured. E. Cisco Jabber does not have the correct phone button template and hence has not registered to the Cisco Unified Communications Manager. F. The called user presence status is unknown. G. The called user has not been added as a contact in Cisco Jabber. Correct Answer: D Section: Simulation Questions /Reference: : QUESTION 67 Real 78
Real 79
Real 80
The Cisco Telepresence Codec C90 is unable to call the Cisco IP Video Phone. Assuming that the calling search space has been configured correctly, which of the these can cause this issue? Real 81 A. The Cisco Telepresence Codec C90 can only be registered to a Cisco Telepresence Video Communication Server. B. A multipoint control unit is required in order for the call to work. C. The Cisco Telepresence Codec C90 can only be registered as a SIP endpoint to Cisco Unified Communications Manager. H.323 is not supported. D. URI dialing has not been configured on Cisco Unified Communications Manager. E. The Cisco Telepresence Codec C90 Profile 1 > CallSetupMode must be configured as a gateway since Cisco Unified Communications Manager does not have a gatekeeper functionality. F. The Cisco Telepresence Codec C90 is not registered as a SIP endpoint on Cisco Unified Communications Manager. The Cisco Telepresence Codec C90 needs to be registered as both SIP and H.323. Correct Answer: C Section: Simulation Questions /Reference: Real 82 QUESTION 68 Which scheduling and management application can be installed on any hardware platform that meets the minimum specifications that the end customer decides to deploy? A. Cisco Video Communications B. Cisco TelePresence Management Suite C. Cisco Digital Media Manager D. Cisco TelePresence Management Switch E. Cisco Unified Communications Manager Correct Answer: B Section: Video Concepts /Reference: :
QUESTION 69 When scheduling a multipoint conference, which three devices are required for the conference to be scheduled and completed successfully? (Choose three.) A. Cisco Unified Communications Manager B. multipoint control unit C. video conferencing endpoints D. Cisco Unity Connection E. Cisco Unified IM and Presence Correct Answer: ABC Section: Video Concepts /Reference: : QUESTION 70 Which encoder is best suited for professional, studio-quality audio and video processing? A. Scientific Atlanta Encoder B. Cisco Digital Media Encoder 1000 C. Cisco Digital Media Encoder 2000 D. Cisco Digital Media Encoder 3000 Correct Answer: C Section: Video Concepts /Reference: : Real 2 QUESTION 71 Which Cisco Video Surveillance product contains the Cisco Video Surveillance Encoding Server? A. Video Communications Server
B. Cisco Video Surveillance Operations Manager C. Cisco Video Surveillance Media Server D. Cisco Video Surveillance Transcoding and Encoding Server E. Cisco Video Surveillance Virtual Matrix Correct Answer: B Section: Video Concepts /Reference: : QUESTION 72 Which of these is the core component of the Cisco Video Surveillance product suite that handles recording and serving of video feeds? A. Video Communications Server B. Cisco IP camera C. Cisco Video Surveillance Operations Manager D. Cisco Video Surveillance Media Server Correct Answer: D Section: Video Concepts /Reference: : QUESTION 73 Cisco Video Surveillance Video Encoder cards perform which function? A. the ability to use existing analog equipment with an IP-enabled video surveillance system B. the ability to convert low-resolution video to high-definition video for video surveillance C. the ability to stream digital media to digital media in an IP-enabled video recording environment D. the ability to encrypt raw video signals to secure video signals Correct Answer: A Section: Video Concepts
/Reference: : Real 3 QUESTION 74 In an ISR Cisco Video Management and Storage System, what is the maximum storage capacity allowed per module? A. 1 TB per module B. 2 TB per module C. 3 TB per module D. 500 MB per module E. 750 MB per module F. 850 MB per module Correct Answer: A Section: Video Concepts /Reference: : QUESTION 75 Which two issues does utilizing an IP network storage solution for IP video surveillance help overcome? (Choose two.) A. analog to IP conversion B. large, expandable storage space C. physical security D. scalability
E. faster bit rate for storage Correct Answer: BD Section: Video Concepts /Reference: : QUESTION 76 Which Cisco TelePresence multipoint platform utilizes only Cisco Unified Communications Manager for call control? A. Cisco TelePresence Multipoint Control Unit B. Cisco TelePresence Multipoint Switch C. Cisco TelePresence Server Real 4 D. Cisco TelePresence Media Bridge Server E. Cisco TelePresence System 500-32 F. Cisco TelePresence SX20 Correct Answer: B Section: Video Concepts /Reference: : QUESTION 77 Which Cisco Video Surveillance device is responsible for providing video streams to monitors after the respective layouts and views are received by the monitors? A. Cisco IP Video Surveillance Operations Manager B. Cisco IP Video Surveillance Virtual Matrix Viewer C. Cisco Video Surveillance Manager D. Cisco Video Surveillance Media Server Correct Answer: D Section: Video Concepts
/Reference: : QUESTION 78 Refer to the exhibit. Real 59
When the Cisco Jabber Video for TelePresence fails to register with the server, which two fields should be configured at a minimum, assuming SRV records are not configured? (Choose two.) A. the internal or external DNS server name for the Cisco TelePresence Video Communications Server B. the internal DNS server name for the Cisco TelePresence Management Suite
C. the SIP domain D. the IP address of the Cisco TelePresence Management Suite for the internal server E. the IP address of the Cisco Unified Communications Manager for the internal server Correct Answer: AC Section: Conferencing Concepts /Reference: : Real 60 QUESTION 79 When configuring the Cisco TelePresence System 500 with a static IP address, where should the IP address be configured? A. in Cisco Unified Communications Manager after adding the Cisco TelePresence System 500 manually B. in the Cisco TelePresence System Administration tool C. in the Cisco TelePresence Management Suite after the Cisco TelePresence System 500 was added under systems D. Static IP address configuration is not possible. Only a DHCP-provided IP address is supported. E. using the on-screen display Correct Answer: B Section: Conferencing Concepts /Reference: : QUESTION 80 Which Cisco MCU feature allows a video participant to dial in to view permanent and active conferences and select a conference to join, or allow them to create a new conference? A. ad hoc conferencing B. ACD C. Auto Attendant D. preconfigured participant
Correct Answer: C Section: Conferencing Concepts /Reference: : QUESTION 81 Which ad hoc multipoint feature is supported only when properly configured and when the endpoint is registered to the Cisco VCS? A. Multisite B. Multiway C. WebEx enabled Cisco TelePresence Real 61 D. Collaboration Meeting Room E. Cisco MCU F. Cisco TelePresence Server Correct Answer: B Section: Conferencing Concepts /Reference: : QUESTION 82 Which statement is true about the Cisco TelePresence System 500-32 system regarding the HVAC needs for the room where it is installed? Real 16 A. The system does not require any additional requirements above the normal HVAC requirements for the room. B. You must supply additional cooling requirements for the room. C. You must supply a room that has energy-efficient lighting to reduce the temperature of the room. D. The temperature of the room will be 10 to 20 degrees warmer than the rest of the building. Correct Answer: A Section: Endpoint Configuration
/Reference: : QUESTION 83 What is the optimum distance for a person sitting using the Cisco TelePresence System 500? A. The camera can adjust automatically B. 0.5 meters and 0.75 meters (1.5 and 2.5 feet) C. 1.2 meters and 1.8 meters (4 and 6 feet) D. 3.0 and 5.0 meters (10 and 15 feet) Correct Answer: C Section: Endpoint Configuration /Reference: : QUESTION 84 You have installed a C-Series endpoint in an office where DHCP is not supported. At a minimum, which four network items must be configured for the endpoint to be able to register with H.323 on a Cisco TelePresence Video Communication Server located at the external headquarters location? (Choose four.) A. Unique IPv4 address B. Subnet mask C. Default gateway D. Cisco VCS IPv4 address E. Active Directory IPv4 address F. SMTP server IPv4 address Correct Answer: ABCD Section: Endpoint Configuration /Reference: actual answer. QUESTION 85
Which two additional items can be configured for an endpoint to register with the Cisco TelePresence Video Communication Server for H.323 to function correctly? (Choose two.) A. Unique system ID B. Unique H.323 ID C. Unique DNS entry ID D. Unique E.164 alias E. Unique real-time transport protocol port numbers F. Unique NTP server IPv4 address Correct Answer: BD Section: Endpoint Configuration /Reference: : QUESTION 86 Which two additional items must be configured for an endpoint to register manually with the Cisco TelePresence Video Communication Server for the SIP to function correctly? (Choose two.) A. E.164 alias B. H.323 ID C. SIP uniform resource indicator D. Configured SIP registrar and proxy server E. NTP server IPv4 address F. unique system ID Correct Answer: CD Section: Endpoint Configuration /Reference: accurate answer. QUESTION 87 What is the importance of defining option 150 in the DHCP server for Cisco TelePresence endpoints?
A. Option 150 is not important. B. It is the TFTP server IPv4 address where the video endpoint retrieves its configuration file while booting. C. It is the IPv4 address of the default gateway for the subnet that the video endpoint is connected to. D. It is the configured SIP registrar and proxy server. Real 18 E. It is the unique NTP server IPv4 address. Correct Answer: B Section: Endpoint Configuration /Reference: : QUESTION 88 Refer to the exhibit. Real 19 Real 20 Which SIP URI should be dialed in order to reach the endpoint that is registered with the IP address of 172.29.1.221 from another endpoint with a URI of sip:e20@dca256.test? A. 52900121 B. sip:ex90@osl147.local C. ex90@osl148.local D. 172.29.1.221 E. ex90 Correct Answer: B Section: Endpoint Configuration /Reference: authenticated.
QUESTION 89 Refer to the exhibit.
Which two strings that could be dialed to start a multipoint conference that is hosted by the multipoint control unit? (Choose two.) Real 21 A. 52900121 B. ex90@osl147.local C. ex90@osl148.local D. 5919 E. ex90 F. mcu8510@osl147.local Correct Answer: DF Section: Endpoint Configuration /Reference: : QUESTION 90 Refer to the exhibit.
You must dial the interactive response system of the multipoint control unit. What are the appropriate dual-tone multi-frequency digits to create an ad-hoc conference with an identifier of 2345?
A. 2345 Real 22 B. 2345# C. 5919*2345 D. 5919*2345# Correct Answer: D Section: Endpoint Configuration /Reference: : QUESTION 91 When you register the Cisco TelePresence System 500-32 video system with the Cisco Unified Communications Manager, what is the most important item for the registration to be input into the server? A. the IPv4 address of the Cisco TelePresence System 500-32 B. the IP telephone media access control address that is used to manage the system C. the media access control address of the Ethernet port of the Cisco TelePresence System 500- D. The Cisco TelePresence System 500-32 will always automatically register with the Cisco Unified Communications Manager server. Correct Answer: C Section: Endpoint Configuration /Reference: answer is straight.
QUESTION 92 Which well-known port is used to access the Cisco IP Video Surveillance Operations Manager via a secure, ActiveX web session? A. 20 Real 5 B. 80 C. 421 D. 434 E. 443 F. 8080 Correct Answer: E Section: Video Concepts /Reference: : QUESTION 93 Which two of these are considered to be provisioning and scheduling management tools in a Cisco TelePresence environment? (Choose two.) A. Cisco TelePresence Manager B. Cisco Video Surveillance Operations Manager C. Cisco TelePresence Management Suite D. Cisco TelePresence Multipoint Control Unit E. Cisco Video Surveillance Management Server Correct Answer: AC Section: Video Concepts /Reference: answer is fine. QUESTION 94 When you configure a zone for firewall traversal, which type of zone is the Cisco VCS-C configured for? A. client
B. server C. proxy D. gateway E. neighbor Correct Answer: A Section: Video Concepts /Reference: : QUESTION 95 Real 6 When a call is placed from a Cisco VCS registered SIP-only endpoint to an H.323-only endpoint, which type of call license is consumed? A. traversal call B. non-traversal call C. on-net call D. interworking call E. off-net call F. Cisco Unified Workspace Licensing Correct Answer: A Section: Video Concepts /Reference: upgraded answer. QUESTION 96 On the Cisco VCS-E, what is the default port number for the H.323 connection on the first traversal zone between a Cisco VCS-C and Cisco VCS-E? A. 1719 B. 1720 C. 5060 D. 6001
E. 7001 Correct Answer: D Section: Video Concepts /Reference: : QUESTION 97 Which protocol does the Cisco TelePresence Content Server use for call signaling? A. MGCP B. Cisco Proprietary C. SCCP D. H.323 Correct Answer: D Section: Video Concepts /Reference: answer is obvious. QUESTION 98 What is the maximum number of servers that a Cisco TelePresence Content Server cluster can have? A. 6 B. 7 C. 8 D. 10 E. 12 Correct Answer: D Section: Video Concepts /Reference: :
QUESTION 99 XYZ Corporation has more than 1000 Cisco video endpoints and they want a high availability solution for scheduling and OBTP. Which option do you recommend? A. standalone Cisco TelePresence Manager server B. cluster of Cisco TelePresence Manager servers C. standalone Cisco TelePresence Management Suite server D. cluster of Cisco TelePresence Management Suite servers in active/passive failover mode E. load-balanced cluster of Cisco TelePresence Management Suite servers F. Cisco Prime collaboration manager Correct Answer: D Section: Video Concepts /Reference: : QUESTION 100 Refer to the exhibit. Real 8
In this SDP, which IP address and port should the receiving end send its primary video channel media to? A. 192.168.1.4:2048 B. 192.168.1.4:50000 C. 192.168.1.5:50002 D. 192.168.1.5:50008 Correct Answer: C Section: Video Concepts /Reference: : QUESTION 101
Which Cisco feature upscales SD and low-bandwidth video participants up to four times, allows them to appear closer to HD in a video call, and is supported on Cisco MCU and Cisco TelePresence Server multiparty solutions? A. ClearPath B. ClearVision C. WebEx enabled TelePresence D. Active Presence E. Individual Transcoding Correct Answer: B Section: Conferencing Concepts /Reference: Okay. QUESTION 102 In locally managed mode, what is the maximum number of 720p HD video ports in a Cisco MSE 8710 Cisco TelePresence Server cluster running version 4.0? A. 48 B. 60 C. 72 D. 84 E. 96 F. 108 Correct Answer: E Section: Conferencing Concepts
/Reference: : QUESTION 103 Real 62 A Cisco TelePresence Server is operating in locally managed mode. In which two ways can a Cisco EX60 user who is connected to a conference that is hosted on a Cisco TelePresence Server change the screen layout? (Choose two.) A. Using the remote control B. Using DTMF keys 2 and 8 C. Using FECC D. Via the Cisco TelePresence server GUI Correct Answer: BC Section: Conferencing Concepts /Reference: : QUESTION 104 In a Multiway call escalation, which SIP message is sent from the Multiway initiator to the participants to provide the bridge URI? A. TRANSFER B. REFER C. REDIRECT D. 200 OK Correct Answer: B Section: Conferencing Concepts /Reference: : QUESTION 105 In a Cisco TelePresence conference that is hosted on a Cisco MCU, a single pane shows the person who is currently talking. What is this pane called?
A. The host B. The active participant C. The active speaker D. The active floor Correct Answer: C Section: Conferencing Concepts /Reference: answer is fixed. QUESTION 106 During the initial setup of the Cisco TelePresence System 500, you are required to do an initial camera setup that fails. What might be a primary reason that the failure occurs? A. The camera cannot focus on the target. B. The room is too dark. C. The system is too far away from the target. D. The cable to the camera is not connected correctly. Correct Answer: B Section: Endpoint Configuration /Reference: great answer. QUESTION 107 In the H.264 video codec, which type of video frame is sent when the remote side requests a fast picture update? A. I-frame B. P-frame C. B-frame D. C-frame Correct Answer: A Section: Video Concepts
/Reference: fit answer. QUESTION 108 Which component provides flexible options for storing video and audio using a combination of Real 9 network-attached storage, direct-attached storage, and SAN storage deployments? A. Cisco Video Surveillance Media Server B. Cisco Video Surveillance Virtual Matrix Software C. Cisco Video Surveillance Storage System D. Cisco Video Surveillance Transcoding and Encoding Server E. Cisco ISR Video Management and Storage Module Correct Answer: C Section: Video Concepts /Reference: fixed answer. QUESTION 109 Refer to the exhibit. Which system does this web user interface refer to?
A. Cisco Unified Communications Manager B. Cisco Video Communications Server C. Cisco Digital Media Manager D. Cisco TelePresence Management Suite Correct Answer: D Section: Video Concepts /Reference: answer is real. QUESTION 110 Which description of medianet is true? A. A set of protocols that accelerate the delivery of media across the network Real 10 B. A family of switches and routers that support multimedia applications C. When the network works together with the endpoints to scale, optimize, and enhance the performance of collaboration components D. A capability of the network to enhance video streaming quality E. A Cisco proprietary feature that is built on hardware DSP resources Correct Answer: C Section: Video Concepts /Reference: : QUESTION 111 Which option is the embedded component that enables endpoints and collaboration applications to support medianet functionality? A. Media Services Interface B. Open API C. XMPP D. SNMP E. Medianet Agent F. SDN
Correct Answer: A Section: Video Concepts /Reference: : QUESTION 112 Which benefits does the Capture-Transform-Share solution provide? A. voice conferencing services B. WAN optimization services C. security and firewall services D. video conferencing services E. DNS, DHCP, and AD services F. video on demand and video streaming services Correct Answer: F Section: Video Concepts /Reference: : Real 11 QUESTION 113 Which of these needs to be enabled in Cisco Unified Communications Manager in order for the Cisco TelePresence System 500-32 to be able to share a presentation with a Cisco TelePresence System Codec C40 endpoint that is registered to a VCS? A. Allow ix application media B. Send send-receive SDP in mid-call invite C. Allow presentation sharing using BFCP D. Allow presentation sharing using H.235 E. Deliver conference bridge identifier
Correct Answer: C Section: Endpoint Configuration /Reference: : QUESTION 114 What is the main difference between a Cisco TelePresence Multipoint Control Unit and a Cisco TelePresence Multipoint Switch? A. The Cisco TelePresence Multipoint Control Unit is a hardware bridge. The Cisco TelePresence Multipoint Switch is a software bridge. B. The Cisco TelePresence Multipoint Control Unit is a software bridge for immersive and non- immersive endpoints. The Cisco TelePresence Multipoint Switch is a hardware bridge for non- immersive endpoints. C. The Cisco TelePresence Multipoint Control Unit delivers automatic voice-activated switching. The Cisco TelePresence Multipoint Switch provides active presence. D. The Cisco TelePresence Multipoint Control Unit has a latency of less than 10 ms, whereas the Cisco TelePresence Multipoint Switch has a latency of 100 ms. Correct Answer: A Section: Endpoint Configuration /Reference: : QUESTION 115 When placing a call from Cisco Jabber Video for TelePresence to the Cisco TelePresence System Codec C40, which FECCs are available? A. Only zoom-in and zoom-out are available. Real 12 B. Only left and right are available. C. Only up and down are available. D. No FECC is available. E. Left, right, up, down, zoom-in, and zoom-out are all available. Correct Answer: E Section: Endpoint Configuration
/Reference: : QUESTION 116 Which statement is correct regarding the difference between Multisite and Multiway conferencing? A. Multisite requires configuration on the endpoint, whereas Multiway requires the Multiway options key to be installed. B. Multisite requires the presence of a multipoint control unit, whereas Multiway relies on the endpoint conferencing capability. C. Multisite is used to conference in multiple sites, whereas Multiway is intrasite multipoint conferencing. D. Multisite requires the Multisite options key to be installed and configured at the endpoint, whereas Multiway requires a Cisco TelePresence Video Communications Server and a centralized multipoint control unit. Correct Answer: D Section: Endpoint Configuration /Reference: well written answer. QUESTION 117 Which of these devices require configuration in order for an endpoint to initiate a Multiway conference? A. Endpoint only B. Cisco TelePresence Video Communications Server only C. Multipoint control unit only D. Endpoint and multipoint control unit only E. Endpoint and Cisco TelePresence Video Communications Server only F. Endpoint, Cisco TelePresence Video Communications Server, and multipoint control unit Correct Answer: F
Section: Endpoint Configuration /Reference: fine. QUESTION 118 Refer to the exhibit. Which multipoint feature can be configured using the exhibit that was taken from the Cisco TelePresence Video Communications Server? A. Multisite B. Multiway C. both Multisite and Multiway D. Multiway conferences between devices that are registered only to the local Cisco TelePresence Video Communications Server
E. Multisite conferences between Cisco Video Jabber for TelePresence devices only Correct Answer: B Section: Endpoint Configuration /Reference: : QUESTION 119 Threat monitoring in physical access security can be based upon which three of these? (Choose three.) A. Doors Real 15 B. Badges C. Age D. Weather E. Height F. Fingerprints Correct Answer: ABF Section: Endpoint Configuration /Reference: appropriate answer. QUESTION 120 When connecting to a pan-tilt-zoom camera to a C-Series codec, what type of cable must be used for camera control? A. An Ethernet crossover cable (RJ45-to-RJ45) B. An Ethernet cable (RJ45-to-RJ45) C. A serial cable (DB25-to-DB9) D. A VISCA cable (DB9-to-RJ45) Correct Answer: D Section: Endpoint Configuration
/Reference: : QUESTION 121 Which video-bridging solution supports single-screen units and multiscreen systems and keeps multiscreen units grouped together logically during a call? A. Cisco MCU B. Cisco PVDM C. Cisco TelePresence Server D. Cisco TMS E. Cisco TCS Correct Answer: C Section: Endpoint Configuration /Reference: : QUESTION 122 Real 23 Which video-room solution supports internal and external microphones for audio transmission at the same time? A. MX300G2 B. SX80 C. SpeakerTrack60 D. C90 E. Jabber for Windows Correct Answer: A Section: Endpoint Configuration /Reference: answer is upgraded. QUESTION 123
An executive in XYZ Corporation wants to purchase a desktop video endpoint that can be used for conferencing, as well as a monitor when not in a conference. Which option do you recommend? A. C20 B. EX90 C. C90 D. SX80 E. MX300 2nd generation F. Cisco TelePresence Profile Series endpoint Correct Answer: B Section: Endpoint Configuration /Reference: appropriate answer. QUESTION 124 Which Cisco video endpoints run on the Android operating system? A. EX-Series B. DX-Series C. C-Series D. MXP-Series Correct Answer: B Section: Endpoint Configuration /Reference: nice answer. QUESTION 125 Which three Cisco TelePresence endpoints are considered immersive endpoints? (Choose three.) A. TX9000 B. EX90 C. C20
D. T3 E. SX10 F. CTS-3000 G. Jabber Video for TelePresence Correct Answer: ADF Section: Endpoint Configuration /Reference: : QUESTION 126 Which two Cisco TelePresence collaboration endpoints can improve communications, relationships, and user productivity? (Choose two.) A. Cisco WebEx Connect IM B. Cisco Digital Media Players C. Cisco DX650 D. Cisco MX300 G2 Correct Answer: CD Section: Endpoint Configuration /Reference: answer is great. QUESTION 127 Which all-in-one dual-screen solution can be used for an average meeting room without the need for external monitors? A. MX700 B. MX300G2 C. EX90 D. SX80 E. TX9000 F. MX200G2 Correct Answer: A
Section: Endpoint Configuration /Reference: Real 25 : QUESTION 128 Which personal Cisco TelePresence unit can be used as a replacement for a person's computer monitor on their desk? A. EX90 B. MX800 C. TX9000 D. SX10 E. SX80 Correct Answer: A Section: Endpoint Configuration /Reference: : QUESTION 129 Which two codecs are supported on the Cisco Video Surveillance 6400E IP Camera? (Choose two.) A. H.263 B. H.264 C. H.265 D. VP8 E. G.711 F. MP3 G. G.729 Correct Answer: BE Section: Endpoint Configuration
/Reference: to the point answer. QUESTION 130 Which two statements about PoE support on Cisco Video Surveillance 6000 Series IP Cameras are true? (Choose two.) A. PoE is not supported on the Cisco 6000 Series IP Cameras, and you must use a Cisco 12 VDC Real 28 power adapter. B. PoE is not supported on the Cisco 6000 Series IP Cameras, and you must use third-party 24 VAC power adapter. C. The port switch must be 802.3at-compliant to power the camera. D. The port switch must be 802.3af-compliant to power the camera. E. The Cisco 6000 Series IP Camera requires a network cable and a connection to a standard 10/100BaseT-compliant PoE router or switch. Correct Answer: DE Section: Endpoint Configuration /Reference: assessed answer. QUESTION 131 Which call control device does the Cisco DX650 use? A. Video Communications Server B. Cisco Unified Communications Manager C. Cisco TelePresence Server D. Cisco TelePresence Manager E. Video Communications Server and Cisco Unified Communications Manager F. Cisco Unified Communications Manager and Cisco TelePresence Server Correct Answer: B Section: Endpoint Configuration /Reference: appropriate answer.
QUESTION 132 Which level of AES encryption does Cisco Unified Presence and Cisco Unified Communications IM and Presence use? A. 256 bit B. 128 bit C. 2048 bit D. 8 bit E. 512 bit Correct Answer: A Section: Endpoint Configuration /Reference: : Real 29 QUESTION 133 Which optional feature is available for some video endpoints to enable multiparty calls to be hosted directly on the local endpoint? A. WebEx enabled Cisco TelePresence B. Multiway C. Multisite D. MeetMe E. ad hoc Correct Answer: C Section: Endpoint Configuration /Reference: : QUESTION 134 Which two endpoints support the multisite option? (Choose two.) A. C20
B. SX10 C. Jabber D. SX-20 E. EX90 F. EX60 Correct Answer: DE Section: Endpoint Configuration /Reference: : QUESTION 135 Which three Cisco TelePresence endpoints support hosting embedded multisite conferences? (Choose three.) A. EX60 B. EX90 C. C20 D. C90 E. SX10 F. SX20 G. Jabber Video for Cisco TelePresence Real 30 Correct Answer: BDF Section: Endpoint Configuration /Reference: great answer. QUESTION 136 Which function does FECC provide? A. the ability to transfer calls between the SIP and H.323 protocols B. the ability to pan, tilt, and zoom the camera at the far end
C. the ability to switch between content channels D. the ability to send DTMF tones Correct Answer: B Section: Endpoint Configuration /Reference: real answer. QUESTION 137 In a Cisco TelePresence MX300 G2, what is the minimum bandwidth for 1080p30? A. 768 kbps B. 1152 kbps C. 1472 kbps D. 1873 kbps E. 2560 kbps Correct Answer: C Section: Endpoint Configuration /Reference: : QUESTION 138 Which two options are characteristics of Cisco Jabber? (Choose two.) A. allows desktop sharing B. allows you to locate the active speaker C. allows instant messaging D. allows the One Button To Push feature Correct Answer: AC Section: Endpoint Configuration /Reference:
answer is up to dated. QUESTION 139 Refer to the exhibit.
What can be deduced from the log shown in the exhibit, which was taken from a Cisco TelePresence Codec C60?