CertifyMe Number: 642-176 Passing Score: 800 Time Limit: 120 min File Version: 8.8 http://www.gratisexam.com/ CertifyMe 642-176
Exam A QUESTION 1 Refer to the exhibit. What are the two options available when using the Security Audit configuration task in Cisco SDM? (Choose two.) A. Perform a virus scan. B. Perform a secure audit on the router. C. Perform a one-step lockdown on the router. D. Perform a denial-of-service attack on the router to verify that it is protected. E. Perform a real-time inspection of incoming traffic destined for the router. Correct Answer: BC /Reference: QUESTION 2 The recommended WAN access method for a simplified and cost-effective Cisco Single-Site Secure Network Foundation deployment provides which type of service? A. best-effort B. low latency C. guaranteed quality D. guaranteed bandwidth
Correct Answer: A /Reference: QUESTION 3 Refer to the exhibit. From this Cisco SDM Security Audit Wizard screen, what should you do to secure the router? A. Click Next. B. Click Fix All, then Next. C. Click Fix All, then clear CDP check box, then Next. D. Click Fix All, then clear CDP check box, then Next, then immediately reboot the router. E. Click Fix All, then clear CDP check box, then Next, then manually disable CDP on the WAN interface. F. Click Fix All, then clear CDP check box, then Next, then manually disable CDP on the WAN interface, then immediately reboot the router. Correct Answer: E /Reference: QUESTION 4
Refer to the exhibit. In a Cisco Single-Site Secure Network Foundation implementation, which factor affects your choice of switch configuration? A. type of QoS scheme that is being used B. maximum number of supported IP phones C. maximum amount of packet latency acceptable D. type of security scheme that is being implemented Correct Answer: B /Reference: QUESTION 5 What is the reason for running spanning tree in a Cisco Single-Site Secure Network Foundation solution? http://www.gratisexam.com/ A. to allow management of all network devices B. to aggregate logical network groups together at one central point C. to protect the network in case someone inadvertently creates a physical loop in it D. to ensure that if a device fails another device will automatically take over for it E. to connect like devices, such as phones or computers, in logical network groups
Correct Answer: C /Reference: QUESTION 6 Refer to the exhibit. Which Cisco SDM configuration task would you select to configure a static route to the service provider? A. NAC B. NAT C. Routing D. Quality of Service E. Intrusion Protection Correct Answer: C /Reference: QUESTION 7 Which statement correctly describes network security settings in Cisco Network Assistant for the Catalyst Express 500 switch?
A. The default network security setting is "HIGH". B. The "LOW" setting enables broadcast storm control and limits the number of devices that can connect to a switch port. C. The "LOW" setting disables broadcast storm control and has no effect on the number of devices that can connect to a switch port. D. The "LOW" setting enables broadcast storm control, but has no effect on the number of devices that can connect to a switch port. E. The "LOW" setting disables broadcast storm control but limits the number of devices that can connect to a switch port. Correct Answer: B /Reference: QUESTION 8 Refer to the exhibit. The exhibit is an example of which technology being implemented? A. PAT B. QoS C. 802.1Q D. VLANs E. spanning tree Correct Answer: A /Reference:
QUESTION 9 Which three of these are prerequisites for resetting a Catalyst Express 500 switch when Cisco Network Assistant is unavailable? (Choose three.) A. a switch with no connected devices B. physical access to the switch C. a PC pre-configured with a specific IP address and mask D. at least one enabled switch port that is unconnected to any device E. a PC or laptop with Windows 2000 or Windows XP installed and a web browser that has JavaScript enabled Correct Answer: BDE /Reference: QUESTION 10 If voice and data traffic will be sent and received via a WAN link, what must be configured to provide a certain amount of dedicated bandwidth and to prioritize the voice traffic over other types of network traffic? A. IPSec VPN B. NAT C. QoS mechanisms D. EIGRP routing protocol E. Static routing F. Firewall Correct Answer: C /Reference: QUESTION 11 When using Cisco Network Assistant to configure a WS-CE500-24LC switch, which three are available choices in the port settings window? (Choose three.) A. group mode selections B. duplex mode selections C. port security selections D. auto MDIX selections E. status selections Correct Answer: BDE /Reference: QUESTION 12
When enabling IPS on an ISR using the Cisco SDM IPS Wizard, in what location can the SDF be placed? A. on the NVRAM of the ISR B. on the RAM of the ISR C. on the flash memory of the ISR D. on the USB memory stick of the ISR E. on the IPS Module of the ISR Correct Answer: C /Reference: QUESTION 13 Drop A. B. C. D. Correct Answer: /Reference: Answer: Check certifyme eengine, Download from Member Center QUESTION 14 You are designing a solution that needs to support a full-rate T3 connection. Which router model does the Cisco Single-Site Secure Network Foundation 1.1 Design and Implementation Guide suggest for this solution? A. Cisco 2801 B. Cisco 2811 C. Cisco 2821 D. Cisco 2851
E. Cisco 3825 F. Cisco 3845 Correct Answer: F /Reference: QUESTION 15 During which phase of the Steps to Success methodology for Cisco SMB Security Solutions would the Network Readiness Assessment be used to assess the readiness of an existing network infrastructure and determine which, if any, modifications should be made prior to implementation? A. Plan B. Prepare C. Position D. Perform E. Design F. Develop Correct Answer: B /Reference: QUESTION 16 Refer to the exhibit. Which Cisco SDM configuration task is used to enable the translation of the inside network private IP address to the public IP address?
A. Interface and Connections B. Firewall and ACL C. VPN D. Security Audit E. Routing F. NAT Correct Answer: F /Reference: QUESTION 17 Refer to the exhibit. What does "locking down" the router entail?
A. Prohibiting console access to the router. B. Disabling HTTPS access to Cisco SDM. C. Preventing any alterations to the router's running configuration. D. Shutting down all the router's interfaces. E. Disabling all the vulnerable services on the router. Correct Answer: E /Reference: QUESTION 18 Which two statements about configuring an unconnected Catalyst Express 500 switch from setup mode using a PC are true? (Choose two.) A. you may use either the CLI or CNA for configuration. B. You may make a direct connection to the PC from any port on the switch. C. You must use CLI for initial configuration. D. You must use Cisco Network Assistant to set up the initial configuration. E. You may only make a direct connection from the console port of the switch to the PC serial port. F. You may only make a direct connection from the port with the flashing green LED to the PC. Correct Answer: DF
/Reference: QUESTION 19 Which WAN connection requires a different interface than the standard interfaces provided in the Cisco Single- Site Secure Network Foundation deployment design? A. DSL B. VPN C. Cable D. Metro Ethernet E. Frame Relay Correct Answer: E /Reference: QUESTION 20 Drop A. B. C. D. Correct Answer: /Reference: Answer: Check certifyme eengine, Download from Member Center QUESTION 21 Which two statements about 802.1Q trunking in Secure Network Foundation Design Guide for Single Site Deployments are correct? (Choose two.)
A. There is no 802.1Q trunking used in these designs. B. 802.1Q trunking is used between the access switch and the router. C. Trunking ensures that traffic from only one VLAN is carried on that trunk. D. When 802.1Q trunks are configured, they are also called Native VLANs. E. The Cisco Control VLAN carries only layer 2 control traffic. Correct Answer: BE /Reference: QUESTION 22 To protect the network from external and internal threats, where should Cisco IPS be enabled on an ISR? A. on the untrusted (outside) interface of the ISR B. on the trusted (inside) interface of the ISR C. on the WAN and LAN interfaces of the ISR D. on the console and auxiliary ports of the ISR E. globally on the ISR Correct Answer: C /Reference: QUESTION 23 During which phase of the Steps to Success methodology for Cisco SMB Security Solutions would the Security Technology Requirements document be used to determine a customer's security requirements? A. Prepare B. Plan C. Position D. Perform E. Design F. Develop Correct Answer: B /Reference: QUESTION 24 Which two WAN access methods are specified for a simplified and cost-effective Cisco Single-Site Secure Network Foundation deployment design? (Choose two.) A. DSL B. Cable C. MPLS
D. Wireless E. Leased Line/Frame Relay Correct Answer: AB /Reference: QUESTION 25 Drop A. B. C. D. Correct Answer: /Reference: Answer: Check certifyme eengine, Download from Member Center QUESTION 26 When using the Steps to Success Methodology, where does Quote Builder fit into the deal process flow? A. It encompasses the Validate and Solve steps. B. It encompasses the Discover, Validate, and Present steps. C. It encompasses the Discover, Solve, and Close steps. D. It encompasses the Discover, Validate, and Solve steps. E. It encompasses the Discover, Validate, Solve and Present steps. Correct Answer: A /Reference:
QUESTION 27 Refer to the exhibit. In a Cisco Single-Site Secure Network Foundation implementation, which factors affect the router configuration you select? A. type of QoS scheme that is being used B. maximum amount of packet latency acceptable C. type of security scheme that is to be implemented D. maximum number of supported IP phones per platform Correct Answer: D /Reference: QUESTION 28 In an environment in which multiple VLANs have been defined on Catalyst Express 500 switches, which two statements are correct for ports that have been configured with the Smartport role of "IP Phone+Desktop"? (Choose two.) A. The ports may belong to a configurable data VLAN. http://www.gratisexam.com/ B. The names of the VLANs used by the Smartports are not relevant.
C. The names of the VLANs used by the Smartports are case insensitive. D. The names of the VLANs used by the Smartports are case sensitive. E. The ports may belong to many VLANs, depending on how many PCs are connected to each port. Correct Answer: AD /Reference: QUESTION 29 Refer to the exhibit. Which two interfaces are enabled for 802.1Q encapsulation? (Choose two.) A. Router 1, gig 0/0 B. Router 1, gig 0/1 C. SW1, Gig Port 9 D. SW2, Fast Port 1 to 24 Correct Answer: BC /Reference:
QUESTION 30 When determining a customer's technical requirements for a Cisco Unified Communications solution, which important tool can be used to determine the bandwidth used by different codecs with various voice protocols over different media? A. Network Codec Aggregator Tool B. Voice Codec Bandwidth Calculator C. Bandwidth Estimator Tool D. Voice Bandwidth Calculator E. Unified Communications Bandwidth Tool Correct Answer: B /Reference: QUESTION 31 Refer to the exhibit. All of the computing devices shown are on the same logical network, as if they were all connected to the same switch. Which two features make this possible? (Choose two.) A. PAT B. QoS C. 802.1Q D. VLANs E. spanning tree Correct Answer: CD /Reference: QUESTION 32 Your customer has 21 users, each requiring both PC and IP phone connectivity. Which is the correct configuration for this customer?
A. 1 Cisco 2801 ISR, 1 Catalyst Express 500-24PC B. 1 Cisco 2811 ISR, 1 Catalyst Express 500G-12TC, 2 Catalyst Express 500-24PC C. 1 Cisco 2821 ISR, 1 Catalyst Express 500G-12TC, 2 Catalyst Express 500-24PC D. 1 Cisco 2851 ISR, 1 Catalyst Express 500G-12TC, 3 Catalyst Express 500-24PC Correct Answer: A /Reference: QUESTION 33 Refer to the exhibit. Which three of these are accurate descriptions of values that you will find in the Verified column for different types of products? (Choose three.) A. if the configuration is complete, the word "Done" will be displayed B. if the solution is not orderable, a check mark will be displayed C. if the solution is not configured, a check mark will be displayed D. if the configuration is incomplete, the words "Not Configured" will be displayed E. if the part is a non-configurable part, the words "Not Configurable" will be displayed F. if the solution is configured and orderable, a check mark will be displayed Correct Answer: DEF /Reference: QUESTION 34 Which statement describes the remote sites in a Cisco Single-Site Secure Network Foundation solution with remote teleworkers? A. They use public IP addresses that are routable through the Internet. B. They are part of the VLANs at the central site; they are in the same subnets. C. They are in separate subnets but are part of the private address space of the network. D. They are separate from the central site and use NAT to route through the Internet to the central site. Correct Answer: C
/Reference: QUESTION 35 Refer to the exhibit. Which Cisco SDM configuration task would you use to to enable access and inspection rules on the WAN interface, preventing any external traffic from entering the network unless that traffic is a reply to a session that originated in the internal network? A. Interface and Connections B. Firewall and ACL C. VPN D. Routing E. NAT F. Additional Task Correct Answer: B /Reference: QUESTION 36 Which two statements correctly identify factors to consider when configuring WAN QoS? (Choose two.) A. Voice traffic uses Assured Forwarding.
B. Voice traffic uses priority queuing. C. Voice signaling traffic uses priority queuing. D. Voice signaling traffic uses Assured Forwarding. E. Voice signaling traffic should use priority queuing with Assured Forwarding. F. Voice traffic should be classified in the Best Effort traffic class and use priority queuing with Expedited Forwarding. Correct Answer: BD /Reference: QUESTION 37 Drop A. B. C. D. Correct Answer: /Reference: Answer: Check certifyme eengine, Download from Member Center QUESTION 38 Refer to the exhibit. Which two statements correctly identify the reasons why there is only one static route and there are no dynamic protocols for the configuration shown? (Choose two.)
A. The configuration has not been completed yet on the router. B. There is only one L3 device, thus dynamic routing is not needed. C. Switch Agg 1 and R1 have not achieved L3 adjacency yet, thus whatever routing protocol has been configured on R1 is not completely up. D. The LAN functions at L3, so dynamic routing does not need to be enabled. E. There is only one entry and exit path to the service provider, so one static route is sufficient. Correct Answer: BE /Reference: QUESTION 39 Which routing method is used to determine the forwarding paths for IP traffic in a Secure Cisco Single-Site Secure Network Foundation solution with remote teleworkers? A. static and default routes B. Open Shortest Path First C. Routing Information Protocol D. Enhanced Interior Gateway Protocol Correct Answer: A /Reference: QUESTION 40 When using Cisco Network Assistant to configure Smartports, which two of the following roles can belong only to a VLAN of the type "access"? (Choose two.) A. phone + desktop B. switch C. router D. desktop E. trunk Correct Answer: AD
/Reference: QUESTION 41 Drop A. B. C. D. Correct Answer: /Reference: Answer: Check certifyme eengine, Download from Member Center QUESTION 42 When determining a customer's security requirements using the security site survey from the Steps for Success methodology, which three of these should be included in the customer's security policy and procedures? (Choose three.) A. third-party due diligence policy review B. security personnel policy C. encryption policy D. remote access policy E. application change control policy Correct Answer: ADE /Reference:
QUESTION 43 Which three of these are characteristics of UTP cable? (Choose three.) A. It comes in eight-pair wire bindles. B. An insulating material covers each of the individual copper wires in it. C. The wires in each pair are wrapped around each other. D. EMI and RFI cause only limited degradation to signals running over it. E. It comes in seven categories. F. It has an external diameter of approximately 0.28 inches. Correct Answer: BCD /Reference: QUESTION 44 When resetting a Catalyst Express switch to factory default settings, which three options are available from the Software Recovery window? (Choose three.) A. erase the system configuration B. boot with the factory default image C. boot to a password recovery window D. erase the system configuration and boot with the factory default IOS image E. erase the system configuration and boot from a TFTP-supplied IOS image Correct Answer: ABD /Reference: QUESTION 45 Drop A. B.
C. D. Correct Answer: /Reference: Answer: Check certifyme eengine, Download from Member Center QUESTION 46 You are designing a solution that needs to support 40 IP phone users. Which router model does the Cisco Single-Site Secure Network Foundation 1.1 Design and Implementation Guide suggest for this solution? A. Cisco 2801 B. Cisco 2811 C. Cisco 2821 D. Cisco 2851 E. Cisco 3825 F. Cisco 3845 Correct Answer: C /Reference: QUESTION 47 During which phase of the Steps to Success methodology for Cisco SMB Security Solutions would the Network Readiness Assessment be used to assess the readiness of an existing network infrastructure and determine which, if any, modifications should be made prior to implementation? A. Plan B. Prepare C. Position D. Perform E. Design F. Develop Correct Answer: A /Reference: QUESTION 48 You are designing a solution that needs to support 30 IP phone users. Which switch model and how many switches does the Cisco Single-Site Secure Network Foundation 1.1 Design and Implementation Guide suggest for this solution? A. 2 Catalyst 3750G-12S-S B. 2 Catalyst Express 500G-12TC C. 2 Catalyst Express 500-24PC
D. 1 Catalyst 3750G-12S-S, 1 Catalyst Express 500-24PC E. 1 Catalyst Express 500G-12TC, 1 Catalyst 3750G-12S-S F. 1 Catalyst 3750G-12S-S, 1 Catalyst Express 500-24PC Correct Answer: C /Reference: QUESTION 49 Drop A. B. C. D. Correct Answer: /Reference: Answer: Check certifyme eengine, Download from Member Center QUESTION 50 Drop
A. B. C. D. Correct Answer: /Reference: Answer: Check certifyme eengine, Download from Member Center QUESTION 51 Refer to the exhibit. In a Cisco Single-Site Secure Network Foundation implementation, which factors affect the router configuration you select?
A. type of QoS scheme that is being used B. maximum amount of packet latency acceptable C. type of security scheme that is to be implemented D. maximum number of supported IP phones per platform Correct Answer: D /Reference: QUESTION 52 Refer to the exhibit. All of the computing devices shown are on the same logical network, as if they were all connected to the same switch. Which two features make this possible? (Choose two.)
A. PAT B. QoS C. 802.1Q D. VLANs E. spanning tree Correct Answer: CD /Reference: QUESTION 53 Which two statements correctly identify factors to consider when configuring WAN QoS? (Choose two.) A. Voice traffic uses Assured Forwarding. B. Voice traffic uses priority queuing. C. Voice signaling traffic uses priority queuing. D. Voice signaling traffic uses Assured Forwarding. E. Voice signaling traffic should use priority queuing with Assured Forwarding. F. Voice traffic should be classified in the Best Effort traffic class and use priority queuing with Expedited Forwarding. Correct Answer: BD /Reference: QUESTION 54 When using Cisco Network Assistant to configure Smartports, which two of the following roles can belong only to a VLAN of the type "access"? (Choose two.) A. phone + desktop B. switch C. router D. desktop E. trunk Correct Answer: AD /Reference: QUESTION 55 Which three of these are characteristics of UTP cable? (Choose three.) A. It comes in eight-pair wire bindles. B. An insulating material covers each of the individual copper wires in it. C. The wires in each pair are wrapped around each other.
D. EMI and RFI cause only limited degradation to signals running over it. E. It comes in seven categories. F. It has an external diameter of approximately 0.28 inches. Correct Answer: BCD /Reference: QUESTION 56 The recommended WAN access method for a simplified and cost-effective Cisco Single-Site Secure Network Foundation deployment provides which type of service? A. best-effort B. low latency C. guaranteed quality D. guaranteed bandwidth Correct Answer: A /Reference: QUESTION 57 If voice and data traffic will be sent and received via a WAN link, what must be configured to provide a certain amount of dedicated bandwidth and to prioritize the voice traffic over other types of network traffic? A. IPSec VPN B. NAT C. QoS mechanisms D. EIGRP routing protocol E. Static routing F. Firewall Correct Answer: C /Reference: QUESTION 58 Refer to the exhibit. Which Cisco SDM configuration task is used to enable the translation of the inside network private IP address to the public IP address?
A. Interface and Connections B. Firewall and ACL C. VPN D. Security Audit E. Routing F. NAT Correct Answer: F /Reference: QUESTION 59 Drop
A. B. C. D. Correct Answer: /Reference: Answer: Check certifyme eengine, Download from Member Center QUESTION 60 Which two WAN access methods are specified for a simplified and cost-effective Cisco Single-Site Secure Network Foundation deployment design? (Choose two.) A. DSL B. Cable C. MPLS D. Wireless E. Leased Line/Frame Relay Correct Answer: AB /Reference: QUESTION 61 Refer to the exhibit. Which two interfaces are enabled for 802.1Q encapsulation? (Choose two.)
A. Router 1, gig 0/0 B. Router 1, gig 0/1 C. SW1, Gig Port 9 D. SW2, Fast Port 1 to 24 Correct Answer: BC /Reference: QUESTION 62 Your customer has 21 users, each requiring both PC and IP phone connectivity. Which is the correct configuration for this customer? A. 1 Cisco 2801 ISR, 1 Catalyst Express 500-24PC B. 1 Cisco 2811 ISR, 1 Catalyst Express 500G-12TC, 2 Catalyst Express 500-24PC C. 1 Cisco 2821 ISR, 1 Catalyst Express 500G-12TC, 2 Catalyst Express 500-24PC D. 1 Cisco 2851 ISR, 1 Catalyst Express 500G-12TC, 3 Catalyst Express 500-24PC Correct Answer: A
/Reference: QUESTION 63 Refer to the exhibit. Which Cisco SDM configuration task would you use to to enable access and inspection rules on the WAN interface, preventing any external traffic from entering the network unless that traffic is a reply to a session that originated in the internal network? A. Interface and Connections B. Firewall and ACL C. VPN D. Routing E. NAT F. Additional Task Correct Answer: B /Reference: QUESTION 64 Drop
A. B. C. D. Correct Answer: /Reference: Answer: Check certifyme eengine, Download from Member Center QUESTION 65 Drop A. B. C. D. Correct Answer:
/Reference: Answer: Check certifyme eengine, Download from Member Center QUESTION 66 Refer to the exhibit. In a Cisco Single-Site Secure Network Foundation implementation, which factors affect the router configuration you select? A. type of QoS scheme that is being used B. maximum amount of packet latency acceptable C. type of security scheme that is to be implemented D. maximum number of supported IP phones per platform Correct Answer: D /Reference: QUESTION 67 Refer to the exhibit. In a Cisco Single-Site Secure Network Foundation implementation, which factor affects your choice of switch configuration?
A. type of QoS scheme that is being used B. maximum number of supported IP phones C. maximum amount of packet latency acceptable D. type of security scheme that is being implemented Correct Answer: B /Reference: QUESTION 68 Which three of these are prerequisites for resetting a Catalyst Express 500 switch when Cisco Network Assistant is unavailable? (Choose three.) A. a switch with no connected devices B. physical access to the switch C. a PC pre-configured with a specific IP address and mask D. at least one enabled switch port that is unconnected to any device E. a PC or laptop with Windows 2000 or Windows XP installed and a web browser that has JavaScript enabled Correct Answer: BDE /Reference: QUESTION 69 Drop
A. B. C. D. Correct Answer: /Reference: Answer: Check certifyme eengine, Download from Member Center QUESTION 70 Refer to the exhibit. All of the computing devices shown are on the same logical network, as if they were all connected to the same switch. Which two features make this possible? (Choose two.) A. PAT B. QoS C. 802.1Q D. VLANs E. spanning tree
Correct Answer: CD /Reference: QUESTION 71 You are designing a solution that needs to support 40 IP phone users. Which router model does the Cisco Single-Site Secure Network Foundation 1.1 Design and Implementation Guide suggest for this solution? A. Cisco 2801 B. Cisco 2811 C. Cisco 2821 D. Cisco 2851 E. Cisco 3825 F. Cisco 3845 Correct Answer: C /Reference: QUESTION 72 Which three of these are characteristics of UTP cable? (Choose three.) A. It comes in eight-pair wire bindles. B. An insulating material covers each of the individual copper wires in it. C. The wires in each pair are wrapped around each other. D. EMI and RFI cause only limited degradation to signals running over it. E. It comes in seven categories. F. It has an external diameter of approximately 0.28 inches. Correct Answer: BCD /Reference: QUESTION 73 When using Cisco Network Assistant to configure Smartports, which two of the following roles can belong only to a VLAN of the type "access"? (Choose two.) A. phone + desktop B. switch C. router D. desktop E. trunk Correct Answer: AD
/Reference: QUESTION 74 Which three of these are characteristics of UTP cable? (Choose three.) A. It comes in eight-pair wire bindles. B. An insulating material covers each of the individual copper wires in it. C. The wires in each pair are wrapped around each other. D. EMI and RFI cause only limited degradation to signals running over it. E. It comes in seven categories. F. It has an external diameter of approximately 0.28 inches. Correct Answer: BCD /Reference: QUESTION 75 Drop A. B. C. D. Correct Answer: /Reference: Answer: Check certifyme eengine, Download from Member Center
QUESTION 76 If voice and data traffic will be sent and received via a WAN link, what must be configured to provide a certain amount of dedicated bandwidth and to prioritize the voice traffic over other types of network traffic? A. IPSec VPN B. NAT C. QoS mechanisms D. EIGRP routing protocol E. Static routing F. Firewall Correct Answer: C /Reference: QUESTION 77 Refer to the exhibit. Which Cisco SDM configuration task would you use to to enable access and inspection rules on the WAN interface, preventing any external traffic from entering the network unless that traffic is a reply to a session that originated in the internal network? A. Interface and Connections B. Firewall and ACL C. VPN D. Routing E. NAT
F. Additional Task Correct Answer: B /Reference: QUESTION 78 Drop A. B. C. D. Correct Answer: /Reference: Answer: Check certifyme eengine, Download from Member Center http://www.gratisexam.com/