Photoelectrics Diffuse-reflective, Background Suppression Type PH8CNB... Miniature sensor range Range: mm Sensitivity adjustment by potentiometer Modulated, red light 65 nm Supply voltage: to VDC Output: ma, NPN or PNP preset Make and break switching function LED indication for output and power Protection: reverse polarity, short circuit and transients Cable and plug versions Excellent EMC performance Excelent colour matching Product Description The PH8CNB... is part of a family of inexpensive general purpose diffuse reflective sensors with backgrund suppression in industrial standard 8 mm cylindrical and square ABS housing. The sensors are useful in applications where high-accuracy detection as well as small size is required. Compact housing and high power LED for excellent performance-size ratio. The potentiometer used for adjustment of the sensitivity makes the sensors highly flexible. The output type is NPN or PNP and the output switching function is NO and NC. Ordering Key Type Housing style Housing size Housing material Housing length Detection principle Sensing distance Output type Output configuration Connection type Sensitivity adjustment PH8CNBNAMSA Type Selection Housing style Range Connection Ordering no. Ordering no. S n NPN PNP Make and break switching Make and break switching M8 Square type mm Cable PH 8 CNB NASA PH 8 CNB PASA M8 Square type mm Plug PH 8 CNB NAMSA PH 8 CNB PAMSA M8 Square type mm Pigtail PH 8 CNB NATSA PH 8 CNB PATSA Specifications Rated operating distance (S n) Up to mm, reference target: Kodak test card R7, white, 9% reflective, x mm Maximum detecting distance White object 9% refl. mm Grey object 8% refl. mm Black object 6% refl. 5 mm Blind zone 8 mm Sensitivity control Adjustable by potentiometer Electrical adjustment Mecanical adjustment Temperature drift.%/ºc Hysteresis (H) % Rated operational volt. (U B ) to VDC (ripple included) Ripple (U rpp ) % Output current Continuous (I e) ma Short-time (I) ma (max. load capacity nf) No load supply current (I o) ma @ U B max ma @ U B min Minimum operational current (I m).5 ma -state current (I r ) µa Voltage drop (U d ) VDC @ I e max Protection Short-circuit, reverse polarity and transients Light source InGaAlP, LED, 65 nm Light type Red, modulated Emitter angle ± º @ half sensing distance Ambient light. lux Incandescent lamp Operating frequency (f) 5 Hz Response time - (t ) ms - (t ) ms Power delay (t v) ms Output function Open collector NPN or PNP Specifications are subject to change without notice (.6.7)
Specifications (cont.) Output switching function Indication Output Power Environment Installation category Pollution degree N.O. and N.C. LED, yellow LED, green III (IEC 666/666A; 697-) (IEC 666/666A; 697-) Degree of protection IP 67, IP 69K* (IEC 659; 697-) Ambient temperature Operating Storage Vibration Shock Rated insulation voltage -5 to +6 C (- to + F) - to +7 C (- to +58 F) to 5 Hz,. mm/5 G (IEC 668--6) g / ms, pos, neg per axis (IEC 668--6, 668--) 5 VAC (rms) IEC protection class III Housing material Body Backpart Front material Cable gland Trimmer shaft Locknuts Mounting bracket Connection Cable Plug Pigtail Weight Cable version Pigtail version Plug version CE-marking Approvals * The IP69K test according to DIN 5-9 for high-pressure, high-temperature wash-down applications. The sensor must not only be dust tight (IP6X), but also able to withstand high-pressure and steam cleaning. The sensor is exposed to high pressure water from a spray nozzle that is fed with 8 C water at 8 KPa (8 bar) and a flow rate of 6L/min. The nozzle is held 5 mm from the sensor at angles of,, 6 and 9 for s each. The test device sits on a turntable that rotates with a speed of 5 times per minute. The sensor must not suffer any damaging effects from the high pressure water in appearance and function. ABS, grey PC-Transparent PMMA, red POM, Black POM, Dark Grey PP, black PPA, black PVC, grey x.5 mm, Ø =.5 mm M, -pin (CBNF-series) PUR, grey, cm x.5 mm, Ø =.5 mm M, -pin (CBNF-series) 85 g g 5 g Yes culus (UL58) Supply class 9 6 Detection Diagram Sensing Conditions Sensing range [inches]..9 5.9 7.9 9.8.6. White background 9% [inches] 6,%....9.9 5.9 6.9 7.9 8.9 9.8,%,% [mm] - - -.8. -. -.8 -. [inches] Distance from background [%],% 8,% 6,%,%,% - 5 5 Sensing range [mm] -.6 5,% 5 5 75 5 5 75 5 5 White background 9% [mm] Poly. (Black gr) Poly. (Gray) Poly. (White) Specifications are subject to change without notice (.6.7)
Operation Diagram Tv = Power delay Power supply Object (target) Break Output (N.C.) Make Output (N.O.) Present Not Present Tv Tv Dimensions Cable/Pigtail version.5..5 Power Indicator 5 Operation 7.5 (Green Indicator (Yellow) Power Indicator (Green) 5.5.5 Emitter Sensitivity Control Pigtail M.5 Optical Axis 6. M8 x. 5.5 Receiver Ø 9.9 Ø.5 Plug version.5..5 Power Indicator 5 Operation 7.5 (Green) Indicator (Yellow) Power Indicator (Green) 5.5.5 Emitter Sensitivity Control.5 Optical Axis.8 M8 x. 5.5 Receiver M x plug Specifications are subject to change without notice (.6.7)
Wiring Diagrams NPN BN V PNP BN V BK WH WH BK BU BU V GND V GND Mounting Systems Min.. mm Max..5 mm PH8 mounting with a combination of x APH8-MB and x M8 locknut. Maximum torque.9 NM M8 Locknut APH8-MB APH8-MB Ø 7 6.5 Ø 7 6.5 Installation Hints To avoid interference from inductive voltage / current peaks, separate the proximity switch cables from any other power cables. E.g. Engine, contactor or solenoid cables Relief of the cable strain Protection of the sensing face Sensor mounted on a mobile carrier Correct Correct > mm The cable should not be pulled A proximity switch should not serve as mechanical stop Any repetitive flexing of the cable should be avoided Specifications are subject to change without notice (.6.7)
Delivery Contents Photoelectric switch: PH8CNB... Installation instruction on plastic bag Screwdriver Mounting bracket APH8-MB M8 locknuts Packaging: Plastic bag Accessories Connector type CGA.. / CBNF.. series Specifications are subject to change without notice (.6.7) 5