Installation manual Card reader Sirius i80(p) o Product o Installation o Connection o Technical data

Installation manual Card reader Sirius i80(p) o Product o Installation o Connection o Technical data

Publication January 2014, Keyprocessor BV Paasheuvelweg 20 1105BJ Amsterdam, The Netherlands www.keyprocessor.com Tel.: +31-20-4620700 This manual represents the knowledge at the above mentioned time. Keyprocessor works nonstop to improve her products. For the most recent technical information please contact your consultant or dealer. Content overview Publication... 2 Content overview... 2 1 The product... 3 1.1 Sticker i-serie... 3 1.2 Spacers... 3 1.3 Default reader configurations... 4 1.3.1 Polyx/Orbit Mifare- MifareDesfire... 4 1.3.2 Chip Serie nummer (CSN)... 5 1.3.3 Sirius i-80 programmable using configuration cards... 5 1.3.4 Sirius i-80 programmable using PS application and configuration cards... 5 2 Installation and use... 6 2.1 Location... 6 2.2 Mounting instructions... 6 2.3 Use of the i80/p... 7 3 Connection... 8 3.1 Sirius i80 connector lay-out... 8 3.2 If door controller Polyx... 8 3.2.1 Direct connection (RS485)... 9 3.2.2 Connection using an Adapterboard... 10 3.3 If door controller Orbit... 11 3.3.1 Connecting with UTP cable... 11 3.3.2 Connection with CKY 3x2x0,14mm²... 11 4 Technical data... 12 4.1 Cable specifications... 13 4.1.1 Data signal Clock/Data... 13 4.1.2 Data signal Wiegand... 13 4.1.3 Data signal RS485... 14 4.2 Certificates... 15

1 The product The Sirius i-series card reader is a versatile card reader which supports multiple card technologies and communication protocols. In addition, this card reader is able to support different technologies simultaneously like Mifare classic and DESFire EV1. The card reader is equipped with a function to automatically adjust the antenna on and off when no activity takes place around the card reader. The detection is based on proximity. The purpose of this functionality is to create a card reader as energy efficient as possible and only activate the antenna when a person or card is detected near to the card reader. This manual provides the necessary information concerning the installation instructions, mounting and use of the card reader which is supplied as standard. The Sirius i-series card reader: Sirius i80 Sirius i80/p 1.1 Sticker i-serie On the back of the card reader a sticker placed. This sticker features a QR code. After scanning this QR code, all necessary information will be downloaded automatically. 1.2 Spacers The spacer is designed for the following purpose. It can make the card reader more robust for external influences but it can also be useful when installing the Sirius card reader on existing plants. 801-6120 Sirius i80(p) Spacer 801-6121 Outside mounting spacer

1.3 Default reader configurations When using a default Sirius i-series card reader, four configurations are possible The configurations are described in the paragraphs below. Remark: For more information about the additional options, please contact your contact at Keyprocessor. Remark: The Sirius-i80/P (Pincode) card reader will only work in combination with a Polyx door controller. 1.3.1 Polyx/Orbit Mifare- MifareDesfire Part number: 801-5101 Standard communication: A Polyx based on RS485 An Orbit based on Clock/Data - MIFARE Classic & MIFARE DESFire EV1(coded) Output length when using Clock/Data: When using Mifare Classic, the output length is 8 digits When using Mifare DESFire, the output length is 12 digits Standard LED function: When the reader is provided with power, the LED color is Red. When the LED connection is switched to GND, the LED color is Green Standard IO function: When using Mifare Classic, the output length is 8 digits A standard configured card reader does not use the extra IO functionality. When this function is needed, you need to order another card reader. See chapter 1.3.3 & 1.3.4 Programmable: The card reader is not programmable.

1.3.2 Chip Serie nummer (CSN) Part number: I80 801-5112 I80p 801-5122 Default Card reader protocol: An Orbit based on Clock/Data. Output length based on Clock/Data: The length of the Chip Serial Number (CSN) is 4 byte swapped (10 digits decimal) Attention! When using a 7 byte (random) CSN, the card reader must communicate with a Polyx. In this case you need to order another card reader. See chapter 1.2.3 & 1.2.4 Standard LED function: When the reader is provided with power, the LED color is Red. When the LED connection is switched to GND, the LED color is Green Standard IO function: A standard configured card reader does not use the extra IO functionality. When this function is needed, you need to order another card reader. See chapter 1.2.3 & 1.2.4 Programmable: The card reader is not programmable. 1.3.3 Sirius i-80 programmable using configuration cards Part number: 801-5113 After connecting the Power to the card reader, the LED turns blue / purple. A configuration card is needed to turn the reader in operational mode. You can order a configuration card via Keyprocessor. To create 'custom' configuration cards extra costs will be calculated. 1.3.4 Sirius i-80 programmable using PS application and configuration cards Part number: 501-5114 After connecting the Power to the card reader, the LED turns blue / purple. A configuration card is needed to turn the reader in operational mode. The card reader is fully programmable using a PC application and you re able to create your own configuration cards.

2 Installation and use By the use of ferrite, the card reader is insensitive to be installed on a metal surface. 2.1 Location Determine the location where the Sirius card reader should be installed. There is a maximum cable length between the reader and door controller. Exception: using an external power supply, you can increase the achievable distance between the door controller and card reader. Install the reader with a minimum lateral distance of 20 cm from each other. 2.2 Mounting instructions Mount the card reader preferably on an outlet Picture 1: Sirius i80 measurements Pull the cable through the mounting plate of the Sirius reader. The screw hole of the card reader should be placed on the underside. Mount the back plate of the card reader to the outlet, using the existing screws. When not removed, remove the orange colored film of the Buzzer Click the front of the card reader at the top of the mounting plate Attach the front of the card reader to the mounting plate with the supplied 'special mounting bolts.

2.3 Use of the i80/p When entering the PIN code, the finger must be released at least 1 cm from the panel before the next digit is entered.

3 Connection Remark! Depending on the configuration of the card reader, the inputs and outputs of the card reader can be used. 3.1 Sirius i80 connector lay-out Connect the cable as shown in this chapter Pin number Clock/Data Wiegand RS485 7 Vcc (+) Vcc (+) Vcc (+) 6 GND (-) GND (-) GND (-) 5 Ext. Input 1(LED) Ext. Input 1(LED) Ext. Input 1 4 Clock D1 Ext. Output 2 3 Data D0 Ext. Output 1 2 Ext. Input 2 Ext. Input 2 B 1 Ext. Output 1 Ext. Output 1 A The reader accepts a supply voltage of 5.0-16.0 VDC. A higher input voltage results in a lower power consumption and provide cost-effective wiring with a smaller diameter of the conductor. When using an external power supply, it must comply with the SELV guidelines. 3.2 If door controller Polyx The Sirius card reader can be connected in two ways with the Polyx : directly or by using an Adapterboard For optimal communication, it is recommended to have the latest version of one of the following operating system 2.6 JFSS2 3.3 UbiFS

Remark! Browse to the polyx to see the version information. For more information about the versions, see the KP_Install_update_Polyx manual. 3.2.1 Direct connection (RS485) Recommended cable type between a Polyx and the Sirius card reader is: (see chapter 4.1 for more information) CAT5 UTP four twisted pairs of 24AWG copper conductors CAT6 UTP four twisted pairs of 24AWG copper conductors A direct connection (without using an Adapterboard) between the Sirius card reader and a Polyx is NOT possible when: Sirius and Polyx are installed in different buildings and thus the connection leaves the building or the wiring is no UTP cable (CAT5 or CAT6) or an existing (non UTP) cable is reused or overvoltage protection for the card reader is required or An external power supply is required for the card reader. If any of the above conditions applies, see section 3.2.2. Polyx, directly connected to a Sirius card reader: Picture T-568B Pin number RJ- 45 Plug Polyx PRT 2/3 TIA/EIA-568-B Cable color Signal Connection Sirius i30 card reader 1 White/orange B 2 2 Orange A 1 3 White/green B 2 4 Blue Vcc (+) 7 5 White/blue 6 Green A 1 7 White/brown 8 Brown GND (-) 6

3.2.2 Connection using an Adapterboard Recommended cable type between a Polyx and the Sirius card reader, using an Adapterboard is: Shielded cable with twisted pairs If a direct connection is not possible, an Adapterboard must be placed between Polyx and the Sirius card reader. Adapterboard and Polyx are connected with a default UTP cat5 cable (or higher) (plug connection). Connecting wires as shown in the diagrams below. Or screw connection on Adapterboard Or RJ45 connection on Adapterboard TIA/EIA-568-B Cable color Signal Connection Sirius i80 Sirius i80(/p) card reader A (or 1) 1 White/orange B 2 B (or 2) 2 Orange A 1 Y (or 3) 3 White/green B 2 + 4 Blue Vcc (+) 7 5 White/blue Z (or 6) 6 Green A 1 7 White/brown 8 Brown GND (-) 6 Connect GND of the Adapterboard to the local Earth. Connect the shield of the ground cable to the GND connection of the Adapterboard. Do not place any jumpers! For more information see the Adapterboard manual. Possible connections of the card reader Sirius on the Adapterboard

3.3 If door controller Orbit Recommended cable type between the Orbit and Sirius card reader: CKY 3x2x0,14mm² CKY 4x2x0,14mm² CAT5 UTP four twisted pairs of 24AWG copper conductors CAT6 UTP four twisted pairs of 24AWG copper conductors 3.3.1 Connecting with UTP cable TIA/EIA-568-B Cable color Connection on the Orbit Connection Sirius i80 card reader White/orange Data/D0 3 Orange - - White/green Clock/D1 4 Blue +5V 7 White/blue LED 5 Green - - White/brown GND 6 Brown GND 6 3.3.2 Connection with CKY 3x2x0,14mm² Cable color Connection on the Orbit Connection Sirius i80 card reader Green Data/D0 3 Yellow Clock/D1 4 Pink +5V 7 Grey LED 5 White GND 6 Brown GND 6

4 Technical data Model Sirius i80 card reader Interface Sirius Clock/Data, Wiegand Sirius - Polyx (RS485) Data type Read Read/write Readable cards Mifare 1K, Mifare 4K, Mifare DESFire 0.6, Mifare DESFire EV1 8K and ISO14443A compatible card Mifare 1K, Mifare 4K, Mifare DESFire 0.6, Mifare DESFire EV1 8K, Rijkspas and ISO14443A compatible card Power supply 5-16V DC Average: 0,7W Peak: 1,4W Led consumption, both on On 12V, max. 1,8W 100% LED input LED input with pull-up, active low Ext. output Ext. input 1 Dimensions (mm) i80 Reading Distance i80 Environmental Rating i80 5-16V DC Average: 0,7W Peak: 1,4W max. Voltage 45V; Open collector output; sinked current. Max. current 500mA Resistance 1kOhm 80x80x19 5mm-70mm for ISO14443A Mifare card; (depending on environment and transponder) IP64 Operating Temperature -31º to 150º F (-35º to 65º C) Storage Temperature -67º to 185º F (-55º to 85º C) Operating Humidity 5% to 95% relative humidity non-condensing Transmit Frequency 13.56 MHz Standard ISO14443 A Indicators 2x RGB LED and 1 buzzer Connection 7-pin screw connector Certifications CE

4.1 Cable specifications Cable specifications (non-shielded) min.conductor size with Maximum cable length 12 VDC supply 1 = 5V DC Interface Meters Feet mm 2 AWG 40 130 0.14 26 Wiegand 80 260 0.25 24 120 390 0.34 22 Clock/Data 20 1 66 1 0.25 24 0.14 26 0.34 22 RS485 (cable power) RS485 (external power) 120 200 0.25 24 150 490 0.34 22 600 1965 0.25 24 4.1.1 Data signal Clock/Data 4.1.2 Data signal Wiegand

4.1.3 Data signal RS485

4.2 Certificates