Multimedia Bluetooth Tower Speaker KASPRBTTOWA Quick Start Guide &WARNING: CHOKING HAZARD - Small parts and batteries. Not for children. Use with adult supervision only
In the Box Base Stand Remote Control Quick Start Guide 2 sets of screws/washers 3.5mm Auxiliary Cord Tower Speaker Installing the Battery 1 2 3 Note: The battery for the remote control (1 x CR2025 lithium battery) is included. To replace the battery, push and slide out the battery door in the remote control. Replace the battery with a new CR2025 battery, with the polarity + facing upwards. Slide the door back into position.
Controls Top Panel 1 2 3 4 5 6 7 8 9 10 11 1. FM Radio indicator light 2. Bluetooth indicator light 3. AUX IN jack/indicator light 4. USB charging port (use to charge external devices) 5. button: Standby power / hold to turn ON/OFF 6. Mode button: press to change input mode (FM, Radio, Bluetooth, AUX IN) 7. button: skip to previous track / hold to scan FM stations 8. button: press to play/pause / mute in FM mode / hold to enter Bluetooth pairing mode 9. button: skip to next track / hold to scan FM stations 10. VOL- button: decrease volume 11. VOL+ button: increase volume Back Panel 12 13 12. Power switch: main power 13. Light switch: turn LED lights on/off
Remote Control Setup 1 4 7 10 2 3 5 6 8 9 11 12 1. key: Standby power / turn ON/OFF 2. MODE key: press to change input mode (FM, Radio, Bluetooth, AUX IN) 3. key: Press to mute volume 4. FM Scan key: Auto scan FM radio 5. CH- key: preset FM radio station 6. CH+ key: preset FM radio station 7. key: skip to previous track / hold to scan FM stations 8. key: skip to next track / hold to scan FM stations 9. key: play/pause 10. PAIR key: enter pairing mode, or unpair 11. VOL key: decrease volume 12. VOL+ key: increase volume 1 2 1. IR remote sensor 2. Whole tone speakers 3. Base stand 4. Screws 5. Washers 5 3 4 1. Connect the wooden base to the main body using the supplied screws and washers. 2. Insert the AC plug into a power socket.
Pairing Speaker with a Bluetooth Device 1. Plug the speaker into a power source. 2. Turn the speaker ON by pressing the Main power switch on the back of the unit. 3. Press the standby power button on the speaker or on the remote control to turn on the unit. 4. Press the MODE button on the speaker or the PAIR key on the remote control repeatedly until the Bluetooth indicator light flashes GREEN. 5. Keep the speaker and Bluetooth enabled device within 3 feet of each other during the Within 3 feet pairing process. 6. Set your mobile phone or other Bluetooth enabled device to search for Bluetooth devices. Pairing with an iphone Go to SETTINGS > GENERAL > BLUETOOTH Ensure that Bluetooth is turned ON Pairing with a Blackberry Go to SETTINGS/OPTIONS > BLUETOOTH Enable Bluetooth
Pairing with an Android Phone Go to SETTINGS > BLUETOOTH > MENU > Search for devices. (Make sure Bluetooth is turned ON) Pairing with other phones/devices Review the instruction manual that came with your phone or device. 7. When the Bluetooth enabled device finds the speaker, select Kogan BT Tower from the list of found devices. 8. If required, enter the password 0000. Select OK or Yes to pair the two units. 9. After successful pairing, the indicator light will become solid GREEN. The unit will stay paired unless unpaired manually by the user, or is erased due to a reset of the device. If your device should become unpaired or you find you are unable to connect, repeat the above steps or press the PAIR button to start the pairing process again. Note: if the speaker has already been connected to the Bluetooth device/phone, the speaker will reconnect to it automatically. Note: the screenshots on the previous page are typical of many Bluetooth enabled devices on the market today, and are used here to assist in the explanation of the pairing process. Your Bluetooth enabled device's interface and interaction with the speaker may slightly differ from the illustrations above. Using your Bluetooth Speaker 1. Flip the main power switch on the rear of the unit to the ON position. 2. Press the button to turn the unit ON. 3. Press the MODE button on the speaker or the MODE key on the remote control repeatedly to switch to Bluetooth mode. The source indicator will light up GREEN accordingly.
4. Press the VOL- and VOL+ buttons on the speaker or on the remote control to adjust the volume level. 5. Press the key on the remote control to turn the sound off. Press it again to turn the sound back on. Playing Music Make sure that the Bluetooth connection between the speaker and the Bluetooth enabled device is active. (See Bluetooth pairing & linking operation.) 1. Press the button on the speaker or the key on the remote control to play a track. Press again to pause. 2. Press on the speaker or the remote control to skip forward to the next track and to skip backward to the previous track. 3. Press VOL- and VOL+ on the speaker or the remote control to adjust the volume level. Note: you may also adjust the volume from your mobile phone's volume control. FM Radio Mode 1. Press the MODE button on the speaker or on the remote control repeatedly until the FM indicator turns GREEN. 2. Press the or buttons on the speaker or the remote control to tune up/down through the radio stations. 3. To scan to the next available station, press and HOLD the or buttons for one second. 20 stations will be saved as presets. 4. Press the FM SCAN key on the remote control to search all available stations. 5. Press the and buttons on the speaker or the CH+ and CH- keys on the remote control to select a preset station. Note: to enhance radio reception, fully unwind and extend the FM antenna cable located on the back of the speaker. Using as Wired Speakers 1. Plug one end of the included 3.5mm auxiliary cord into the headphone jack on your device. 2. Plug the other end of the 3.5mm auxiliary cord into the AUX jack on top of the speaker. 3. Flip the POWER switch on the back of the speaker to the ON position, then press the button to turn the unit ON. 4. Press the MODE button on the speaker or on the remote control repeatedly until the AUX indicator turns GREEN. 5. Use your device's audio controls for music playback. Note: only VOL+ and VOL- buttons on the speaker are operational when a device is plugged into the AUX jack.
Troubleshooting Tips Issue I can pair the tower speaker with my bluetooth device but I cannot hear any music. I cannot get the tower speaker into Pairing Mode. My bluetooth device is not able to pair with the tower speaker. Suggested solution 1. Make sure your Bluetooth device supports A2DP profile. 2. Turn up the volume on your Bluetooth device. 3. You may have to unpair the speaker, then re-pair the speaker to your device. 1. Make sure the tower speaker system is turned ON before beginning the pairing process. 2. Press the Pair button and wait for the indicator light to flash GREEN. 3. The speaker should now be in pairing mode. 1. Make sure that the tower speaker is turned ON before beginning the pairing process. 2. Keep your tower speaker and bluetooth enabled device within 3 feet of each other during the pairing process. 3. Press the pair button and wait for the indicator light to flash GREEN. 4. Check that your device's Bluetooth function is turned ON. 5. Try repeating the pairing process. See ( Pairing Speaker with a Bluetooth Device ). Safety Instructions Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this tower speaker near water. Clean only with a dry cloth. Do not block any ventilation openings. Do not install near any heat sources such as radiators, heaters, stoves, ovens or any other devices that produce heat. Protect the power cord from being walked on or pinched particularly at plugs or the point where they exit from the speaker. Unplug the tower speaker during lightning storms or not being used for a long period of time. Refer all servicing issues to the Kogan customer support team.