BREATHALYSER
Congratulations on buying your new Wingmate Pro breathalyser. We hope you enjoy owning your Wingmate Pro breathalyser. If you have any questions regarding the unit or want to speak with us further, please visit andatech.com.au or call 1300 800 200 (between 9am and 5pm Monday to Friday). Wingmate Pro Components Mouthpiece Slot Breath out (do not cover) Digital LCD Display Power Button Contents: Breathalyser, mouthpieces (x5), AAA batteries (x2), and user s manual Battery Cover (Back) Specifications Sensor Indication of B.A.C Accuracy Operation Temperature Storage Temperature Warm Up Time Response Time Display Power Supply Use Mouthpiece Dimensions (mm) Weight Calibration Fuel Cell Sensor 0.000 to 0.400 %BAC ±0.005 %BAC at 0.050 %BAC 5 C to 40 C 0 C to 40 C 15 ~ 35 seconds 3 ~ 22 seconds 3-Digit LCD Two 1.5V AAA size alkaline batteries Compatible with Wingmate mouthpieces 114 (height) X 47 (width) X 24 (thickness) 61.5g (84g including batteries) Recommended every 500 tests or 6 months, whichever comes first. Australian Standards Requirement: 1 month
Display Device is ready to take a test. Start blowing. Battery low. Replace with new batteries. Test result is displayed as a 3 decimal place %BAC reading Displays test result Dual colour LCD backlight. See Warnings Display section in the manual. Result is above 0.050% BAC Operating Instructions 1. Insert a mouthpiece into the mouthpiece slot 2. Press the power button. ON will display and the breathalyser will start warming up, which will take about 15 ~ 35 seconds. 3. The breathalyser will beep and display BLO on the screen. Blow steadily into the mouthpiece and continue blowing until you hear another beep. (If you do not blow into the breathalyser within 20 seconds, it will automatically switch off. Press the power button to switch it back on.) 4. The breathalyser will display a circling line as it analyses the breath sample. It will then beep and display the result for 20 seconds. backlight will change to red and display WARN and sound an audible alert. dim down in the last 5 seconds). another test. The breathalyser will start warming up for a second test. 5. To take another test, repeat from step 2. 6. Switch the breathalyser off by pressing the power button for 2 seconds. Please note:
Warnings Display The breathalyser s LCD Backlight will turn red when any of these errors occur. If the result is higher than 0.050% BAC, the breathalyser will display WARN and sound an audible alert. If the result is above 0.400% BAC, Hot signal is displayed along with alarm sound. If you have tested over 500 times, CAL will show up on the display screen for 3 seconds before warming up for a test. Please send the breathalyser back for calibration. The battery voltage is too low to perform a test. The device will turn off automatically after showing this signal. Please replace with new 1.5V alkaline batteries. The breath sample was not strong enough for a measurement. Please power on the unit again and make sure the breath is strong and steady during sampling. When the ambient temperature is out of the working temperature range (5 C~ 40 C) the unit shows OUT and then turns off. Keep and use the unit within the recommended temperature range. How to Change Batteries Step 1: Apply a small amount of pressure on the battery cover located on the back of the unit. Step 2: Push down and away from the unit to release the cover. Step 3: Replace with new alkaline batteries in the proper positive(+) and negative(-) positions as indicated. Then, replace the battery cover.
unit Pro The Wingmate Pro uses a fuel cell sensor to measure breath alcohol levels. Depending upon the amount of alcohol registered by the sensor after a period of time, it will require recalibration. Andatech recommends the Wingmate Pro is calibrated every 6 months or after 500 uses, whichever comes first. To maintain the unit to Australian Standards, calibration every one (1) month is required.
Version 1.0. Updated December 2015.
Product Registration Wingmate Pro