v Connection + - ground Volt lights are built with flying leads and have load limiting resistors for use with any regulated volt DC power source. Flying/tinned leads V power supply v Connection + - Volt lights are built with flying leads and have load limiting resistors for use with any regulated volt DC power source. Flying/tinned leads V power supply ground ICS Connection gate - 0-0V Analog - + Inline Current Source built into the power cable. Requires v power source ICS ICS (IC) Continous in-line controller V power supply ICS and ICS S Connection Analog Dimming - + ICS and S ICS (I) Combination strobe/continous in-line controller trigger+ (active HIGH) Not used Inline Current Source built into the power cable. V power supply ICS S (IS) Requires v power source Default-OFF strobe/continous in-line controller Default off for ICS S version V power supply
C Connection For Use With: C Connector For use with: DCS Series Controllers C Connection For Use With: CS00, CS00-IC, CS00, CS00-IC, CS0, CS0, MS0, MS0 S000, S6000, S6000-AS C Connector For use with: Legacy Controllers (Not recommended for new applications) C Connection For Use With: C Connector For use with: Pulsar 0 Strobe Controller. M Add On Connection For Use With: v, ICS, and ICS wiring
ICS Specifications M Connector Pin-Out Male end view. Ai lights are built with the male connector standard. Volt Pin +V IN 0-0V ANALOG -V IN GATE ACTIVE LOW GRAY Not Connected ICS Pin +V IN 0-0V ANALOG -V IN GATE ACTIVE LOW GRAY Not Connected Connection Diagram ICS Pin Dimensional Information PIN COLOR DESC. +V IN Not used -V IN ACTIVE HIGH GRAY Analog Dimming, 0-0V
ICS Wiring Diagrams Power Connection Options STANDARD OPERATION LIGHT IS ALWAYS ON +VDC ACTIVE LOW GATE LOW TRIGGER SHUTS LIGHT OFF +VDC.7K TRIGGER NPN 0-0V ANALOG CONTROL LINEAR OUTPUT ADJUST +VDC 0-0V ADJUST. ACTIVE HIGH GATE HIGH TRIGGER SHUTS LIGHT OFF +VDC.7K TRIGGER PNP 0-0V ANALOG CONTROL LINEAR OUTPUT ADJUST WITH EXTERNAL POTENTIOMETER +VDC K 0-0V ADJUST.
ICS Wiring Diagram for Optional Manual Intensity Control Power Connection Options MP-ICS Manual Dimming Control Wiring Diagram for ICS All connections are made at the input ICS /S Specifications Parameter Specification Notes Input Voltage Range Strobe output +8 to 0 VDC V nominal 0 - A* * Pulse-width/Light head dependent Max. Repetition Rate 00 Hz ** ** Light head dependent Current Output Adj. Min to Max Current adj. as established by factory setting Maximum current set assuming 00µSec operation Max. Input Current.A Approx 00mA local Trigger Active HI: Active HI: TTL compatible, 0VDC tolerant Mode Select Bypass triggering mode Mechanical & Environmental Storage Temperature Operating Temperature Housing Material Weight Size -0 to +C 0 to +70C High Impact Polycarbonate Approx.7 oz Approx.L x 0.67W x 0.70H Cable Not Included Inches ICS PINOUT GRAY VIN + VIN - Not used Active HIGH trigger input Analog dimming, 0-0V
ICS /S Wiring Diagrams WIRING DIAGRAMS -0VDC * ON i / / PIN OFF I/O PNP / SOURCING i / / PIN *External resistors may not be needed Check documentation on I/O for recommendations and voltage limits -0VDC * i / / PIN OFF ON I/O NPN / SINKING i / / PIN The i does not have a true sinking input. The emitter must be tied to the trigger as shown *External resistors may not be needed Check documentation on I/O for recommendations and voltage limits i / GRAY / PIN -0VDC i / / PIN Analog Dimming: 0 = 0%, 0 = 00% output Analog dimming works in both strobe and continuous 6
ICS /S Wiring Diagrams WIRING INFORMATION TYPICAL CONNECTION - CONTINUOUS USE +V (PIN ) (PIN ) ANALOG GRAY (PIN ) i Light is on continuous when power is applied. Analog control is optional for remote dimming (0-0VDC) TYPICAL CONNECTION - STROBE MODE +V (PIN ) (PIN ) TRIGGER+ (PIN ) ANALOG GRAY (PIN ) i Light is on continuous when power is applied. The first trigger pulse will initiate STROBE MODE. The controller remains in STROBE MODE until the power is toggled. Output light pulse width always follows the duration of the input trigger width. A period of overdrive occurs within msec from the beginning of the pulse. After this period of time, the on-time of the pulse is at the continuous output level. ADAPTIVE OVERDRIVE DIAGRAM 7
M Connector Pin-Out Male end view. Ai lights are built with the male connector standard. Volt Pin +V IN 0-0V ANALOG -V IN GATE ACTIVE LOW GRAY Not Connected ICS Pin +V IN 0-0V ANALOG -V IN GATE ACTIVE LOW GRAY Not Connected ICS Pin +V IN Not used -V IN ACTIVE HIGH GRAY Analog Dimming, 0-0V Dimensional Information 0.7 0.80 0.90.6 DIMENSIONS IN MM 8
Warranty Information Every Advanced illumination, Inc. (Ai) product is thoroughly inspected and tested before leaving the factory. Products are warranted to be free of defects in workmanship and materials for a period of two years from the original date of purchase. Should a defect develop during this period, please contact Ai Customer Service or your Ai distributor for a Return Merchandise Authorization (RMA), and return the complete product, freight prepaid, to Ai. If a defect is found, Ai will - at our discretion - repair or replace the product without charge. Ai claims no liability for any implied warranties, including merchantability and fitness for a specific purpose. Electromagnetic Compatibility This product was tested and complies with the regulatory requirements and limits for electromagnetic compatibility (EMC) as stated in the product specifications. These requirements and limits are designed to provide reasonable protection against harmful interference only when the product is operated in its intended industrial electromagnetic environment. To minimize the potential for electromagnetic interference or unacceptable performance degradation, install and use this product in strict accordance with the instructions in the product documentation. Customer Service For information on existing orders, or to make an order adjustment, contact us Monday through Friday 8:00 am to :00 pm, EST or send an email to orders@advill.com. Company Information Advanced Illumination 0 State Garage Road, Rochester VT. 0767 Phone: 80.767.80 Fax: 80.767.8 Email: info@advancedillumination.com Web: advancedillumination.com 0 Advanced Illumination Inc. All rights reserved 9