Laser Barcode Scanner Model no. LS6007 FS5027 User s Manual
FCC Compliance This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment. Limited Warranty No warranty of any kind is made in regard to this material, including, but not limited to, implied warranties of merchantability or fitness for any particular purpose. We are not liable for any errors contained herein or for incidental or consequential damages in connection with furnishing, performance or use of this material. We shall be under no liability in respect of any defect arising from fair wear and tear, willful damage, negligence, abnormal working conditions, failure to follow the instructions and warnings, or misuse or alteration or repair of the products without written approval.
Table of Contents 1. INTRODUCTION.. 2~3 2. INSTALLATION.....4~7 3. SET UP FROM BAR CODE LABEL...8 Multi-interface Functions. 9~11 Interface-Serial.. 12~13 1D Symbologies On/Off.14~15 2D Symbologies On/Off.16 Symbologies Set Up.17~21 Termination String Setup Bar Codes..22 1
Introduction 2
RIOTEC LS6007 FS5027 2D Laser barcode scanner, using Intermec engine, combines the best scanning performance and value. The device provides an accurate, easy, and fast method of data entry and data storage for computerized information systems. It is easy to install drivers to operate. RIOTEC LS6007 FS5027 2D laser barcode scanner can compatible several interfaces (RS232-USB, RS-232,) and numerous configurations, is a powerful and reliable handheld scanner without compromise. All the operating parameters are programmed by bar code programming menu and stored in non-volatile RAM which can retain the settings after power is turned off. LED (blue/red) Exit Window Buzzer Buzzer Trigger Handle Exit Window LED When a barcode is successful decoded, the blue LED light of the scanner will turn on and off. The scanner will beep once. 3
Installation Insert the plug on the free end of the Communications Cable into the appropriate connector on the host as below described: 1. USB cable Connection: Connect with host Reset Configuration to Defaults If you are unsure of the scanner configuration or have scanned the incorrect codes, please scan the Reset Configuration to Defaults barcode below. This will reset the scanner to its factory defaults settings in USB interface. 2. RS232 cable Connection: connect with host Require 5V adapter for power supply 4
NOTE: for Serial port (RS232 cable), please plug the power connector of 5V power adapter to RS232 cable. 1. Be sure that Host computer is turned OFF 2. Connect scanner cable to the USB port(com port) on the host system. 3..Ensure that all connections are secure. Turn on your host. 4. And please operate the scanner under the right software application. 5. Install the software PL-2303 Driver Installer.exe to the host system.. 6. Go to My Computer One click right button of mouse Administrate Device Administrator Connect Port (COM and LPT). 7. Choose Prolific USB-to-Serial Com Port, and see identify COM number, ex. COM 5. 8. Go to START Programs Accessories Communications Hyper Terminal. 9. Run Hyper Terminal and make the right setting: 9600, 8-data bits, NONE-parity, 1-stop bit, NONE-flow control. 10. Aim the scanner at a barcode, ensure that the scanner is in trigger mode (default), and press the trigger. 11. On successful decode, the blue LED light will turn on and off. The scanner will beep once. And will show the bar code data on the screen. Detail set up on the Hyper Terminal, please see at the Figure 1 to Figure 3. 5
Reset Configuration to Defaults If you are unsure of the scanner configuration or have scanned the incorrect codes, please scan the Reset Configuration to Defaults barcode. This will reset the scanner to its factory defaults settings. Please read following 2 barcode to reset to defaults. Load All Factory Default Pro CMD:0001000 Save as User Default Pro CMD:0001150 Load User Default Pro CMD:0001160 6
If USB(HID) VERSION,PLEASE SET THE OUT PUT MODE AS USB(HID) Operation 12. Be sure that Host computer is turned OFF. 13. Ensure that all connections are secure. 14. Turn on your host. And please operate the scanner under the right software application, such as Notepad or Word(RS232 interface should be under Hyper Terminal and make the right setting). 15. Aim the scanner at a barcode, ensure that the scanner is in trigger mode (default), and press the trigger. 16. On successful decode, the blue LED light will turn on and off. The scanner will beep once. Tip Do not hold the scanner directly over a barcode at 90. Scanning light bounces directly back into the scanner from the barcode label is known as specular reflection which will create a "dead zone" where decoding is difficult. Practice a few times to find what range of angles works best. Maintenance Cleaning the scan window is the only maintenance required. A dirty window may affect scanning accuracy. Wipe the scanner window gently with a lens tissue or other material suitable for cleaning optical material. Do not spray water or other cleaning liquids directly onto the window. 7
Setup from Bar Code Label 8
** Code Programming ON Pro CMD:0006010 ** Code Programming OFF Pro CMD:0006000 Multi-Interface Functions Please read following 2 barcode to reset to defaults. RESET CONFIGURATION TO DEFAULTS Save as User Default Pro CMD:0001150 Load User Default Pro CMD:0001160 Operating settings ** Hand-held Mode Sensor Mode Pro CMD:0302000 Pro CMD:0302010 Continuous Mode Pro CMD:0302020 9
** Code Programming ON Pro CMD:0006010 ** Code Programming OFF Pro CMD:0006000 Sensor Mode Timeout Sensor Mode ** High Sensitivity (= 4) Pro CMD:0313000 Pro CMD:0312020 Normal Sensitivity (= 7) Low Sensitivity (= 10) Pro CMD:0312010 Enhanced Sensitivity (= 1) Pro CMD:0312000 Program Sensitivity Pro CMD:0312030 Pro CMD:0312040 10
** Code Programming ON Pro CMD:0006010 ** Code Programming OFF Pro CMD:0006000 Allow Reading All = enable to read all symbologies and programming codes Prohibit Reading All = allow reading programming codes only. Pro CMD:0001020 Allow Reading All 1D Pro CMD:0001010 Prohibit Reading All 1D Pro CMD:0001040 Allow Reading All 2D Pro CMD:0001030 Prohibit Reading All 2D Pro CMD:0001060 Pro CMD:0001050 11
** Code Programming ON Pro CMD:0006010 ** Code Programming OFF Pro CMD:0006000 Interface Serial - 1 SERIAL BAUD RATE - 2400 BAUD RATE SERIAL BAUD RATE - 4800 Pro CMD:0100010 Pro CMD:0100020 SERIAL BAUD RATE - 9600 SERIAL BAUD RATE - 14400 Pro CMD:0100030 Pro CMD:0100040 SERIAL BAUD RATE -19200 SERIAL BAUD RATE -38400 Pro CMD:0100050 Pro CMD:0100060 SERIAL BAUD RATE -57600 SERIAL BAUD RATE -115200 Pro CMD:0100070 Pro CMD:0100080 12
** Code Programming ON Pro CMD:0006010 ** Code Programming OFF Pro CMD:0006000 Interface Serial - 2 SERIAL DATA BITS - 8 PARA- METERS SERIAL DATA BITS - 6 Pro CMD:0103030 Pro CMD:0103010 SERIAL DATA BITS - 7 SERIAL DATA BITS - 5 Pro CMD:0103020 Pro CMD:0103000 SERIAL STOP BITS - 1 SERIAL STOP BITS - 2 Pro CMD:0102000 SERIAL PARITY - NONE Pro CMD:0102010 SERIAL PARITY - ODD Pro CMD:0101000 Pro CMD:0101020 SERIAL PARITY - EVEN Pro CMD:0101010 13
** Code Programming ON Pro CMD:0006010 ** Code Programming OFF Pro CMD:0006000 CODE 39 ENABLE 1D Symbologies On/Off - 1 CODE 39 CODE 39 DISABLE Pro CMD:0408020 CODE 93 - ENABLE CODE 93 Pro CMD:0408010 CODE 93 - DISABLE Pro CMD:0410020 CODE 128 - ENABLE CODE 128 Pro CMD:0410010 CODE 128 - DISABLE Pro CMD:0400020 CODABAR - ENABLE CODABAR Pro CMD:0400010 CODABAR - DISABLE Pro CMD:0409020 I 2OF5 - ENABLE INTERLEAVED 2 OF 5 Pro CMD:0409010 I 2OF5 - DISABLE 14
Pro CMD:0405020 CHINA POST 25 - ENABLE China post 2 5 Pro CMD:0405010 CHINA POST 25 - DISABLE Pro CMD:0406020 Pro CMD:0406010 15
** Code Programming ON Pro CMD:0006010 ** Code Programming OFF Pro CMD:0006000 UPC-A ENABLE 1D Symbologies On/Off 2 UPC/EAN UPC-A DISABLE Pro CMD:0404020 UPC-E ENABLE Pro CMD:0404010 UPC-E DISABLE Pro CMD:0403020 EAN-8 ENABLE Pro CMD:0403010 EAN-8 DISABLE Pro CMD:0401020 EAN-13 ENABLE Pro CMD:0401010 EAN-13 DISABLE Pro CMD:0402020 Pro CMD:0402010 EAN-128 ENABLE UUC/EAN EAN-128 DISABLE Pro CMD:0412020 Pro CMD:0412010 16
** Code Programming ON Pro CMD:0006010 ** Code Programming OFF Pro CMD:0006000 Data Matrix -ENABLE 2D Symbologies On/Off - 1 Data Matrix Data Matrix -DISABLE Pro CMD:0504020 **Forward Direction Barcode Only Pro CMD:0504010 Both Pro CMD: 0504320 Pro CMD:0504322 Backward Direction Barcode Only Pro CMD:0504321 QR Code -ENABLE QR Code QR Code -DISABLE Pro CMD:0502020 Enable Chinese-Sensible Code Chinese-Sensible Code Pro CMD:0502010 Disable Chinese-Sensible Code Pro CMD:0508020 Aztec -ENABLE Aztec Pro CMD:0508010 Aztec -DISABLE 17
Pro CMD:0503020 Pro CMD:0503010 PDF 417ENABLE PDF 417 PDF 417 DISABLE Pro CMD:0501020 **Forward Direction Barcode Only Pro CMD:0501010 Both Pro CMD:0501320 Backward Direction Barcode Only Pro CMD:0501322 Pro CMD:0501321 Symbologies Set Up - 1 CODE 128 CHECK DIGIT ENABLE CODE 128 CHECK DIGIT CODE 128 CHECK DIGIT -DISABLE Pro CMD:0400150 TRANSMIT UCC/EAN-8 CHECK ENABLE UCC/EAN -8 CHECK BYTE Pro CMD:0400160 TRANSMIT UCC/EAN-8 CHECK DISABLE Pro CMD:0401040 Pro CMD:0401030 18
TRANSMIT UCC/EAN-13 CHECK ENABLE UCC/EAN -13 CHECK BYTE TRANSMIT UCC/EAN-13 CHECK DISABLE Pro CMD:0402040 TRANSMIT UPC-E CHECK ENABLE UPC-E CHECK BYTE Pro CMD:0402030 TRANSMIT UPC-E CHECK DISABLE Pro CMD:0403040 TRANSMIT UPC-A CHECK ENABLE UPC-A CHECK BYTE Pro CMD:0403030 TRANSMIT UPC-A CHECK DISABLE Pro CMD:0404040 Pro CMD:0404030 ** Code Programming ON Pro CMD:0006010 ** Code Programming OFF Pro CMD:0006000 NO Check, Transmit All Interleaved 2 of 5 CHECK BYTE Check, Transmit No Check Pro CMD:0405050 Pro CMD:0405060 Check, Transmit All Pro CMD:0405070 NO Check, Transmit All CHINA POST 25 CHECK BYTE 19 Check, Transmit No Check
Pro CMD:0406050 Pro CMD:0406060 Check, Transmit All Pro CMD:0406070 NO Check, Transmit All CODE 39 CHECK BYTE Check, Transmit No Check Pro CMD:0408050 Check, Transmit All Pro CMD:0408060 Pro CMD:0408070 ** Code Programming ON Pro CMD:0006010 ** Code Programming OFF Pro CMD:0006000 NO Check, Transmit All CODEBAR CHECK BYTE Check, Transmit No Check Pro CMD:0409050 Check, Transmit All Pro CMD:0409060 Pro CMD:0409070 20
NO Check, Transmit All CODE 93 CHECK BYTE Check, Transmit No Check Pro CMD:0410050 Check, Transmit All Pro CMD:0410060 Pro CMD:0409070 21
** Code Programming ON Pro CMD:0006010 ** Code Programming OFF Pro CMD:0006000 Symbologies Set Up 2 EXPAND UPC-E TO UPC-A ENABLE UPC/EAN FORMATING EXPAND UPC-E TO UPC-A DISABLE Pro CMD:0401100 Expand to UPC-A ENABLE Pro CMD:0401090 Expand to UPC-A DISABLE Pro CMD:0403120 2 Digits Addenda ENABLE UCC/EAN-8 Addenda Code Pro CMD:0403110 2 Digits Addenda DISABLE Pro CMD:0401060 Pro CMD:0401050 5 Digits Addenda ENABLE 5 Digits Addenda DISABLE Pro CMD:0401070 2 Digits Addenda ENABLE UCC/EAN-13 Addenda Code Pro CMD:0401080 2 Digits Addenda DISABLE Pro CMD:0402060 Pro CMD:0402050 5 Digits Addenda ENABLE 5 Digits Addenda DISABLE 22
Pro CMD:0402080 Pro CMD:0402070 23
** Code Programming ON Pro CMD:0006010 ** Code Programming OFF Pro CMD:0006000 Symbologies Set Up 3 2 Digits Addenda ENABLE UPC-E Addenda Code 2 Digits Addenda DISABLE Pro CMD:0403060 Pro CMD:0403050 5 Digits Addenda ENABLE 5 Digits Addenda DISABLE Pro CMD:0403080 2 Digits Addenda ENABLE UPC-A Addenda Code Pro CMD:0403070 2 Digits Addenda DISABLE Pro CMD:0404060 Pro CMD:0404050 5 Digits Addenda ENABLE 5 Digits Addenda DISABLE Pro CMD:0404080 Pro CMD:0404070 24
** Code Programming ON Pro CMD:0006010 ** Code Programming OFF Pro CMD:0006000 TERMINATION STRING SETUP BAR CODES Step 1 STRING# 1 TERMINATION CHAR - CR Step 2 Pro CMD:0310000 Step3 Pro CMD:0309010 Pro CMD:0000160 STRING# 1 TERMINATION CHAR - LF Step 1 Step 2 Pro CMD:0310000 Pro CMD:0309000 Step 3 25
Pro CMD:0000160 26
27 Version: 1.0 Date: MAY 27, 2009 P/N: 79.60301.011