IEEE 802.11 a/n Wireless CPE Product Specification Model Name: ZAC-1023-5-13 Version: 0.6
1 Revision History Date Version Author Description 2013/10/14 V0.1 Nancy 1 st release version 2014/01/22 V0.2 Nancy 1. Update software spec 2. Support 8 SSID 3. Change warranty to 2 years 2014/7/3 V0.3 Nancy 1. Support power input change to 24V PoE adapter 2014/7/30 V0.4 Nancy 1. Frequency update 2. Modify safety/country approval from pre-test to certificate. 3. Add NCC support frequency. 4. Add default wireless mode. 2014/8/25 V0.5 Nancy 1. Modify TX power to match EMI test. 2015/9/7 V0.6 Nancy 1. Modify modulation typo. 2. Modify for Outdoor Certification.
2 Specification 2.1 Hardware Specification The Hardware specifications of the product are as below: Table 2-1 Hardware Specification Features Additional Information Chipset Solution CPU: AR9342 RF: AR9342 Standard Compliance - IEEE802.3u MDI / MDIX 10/100 Fast Ethernet - IEEE802.11a/n wireless LAN interface - IEEE 802.11n wireless LAN standard DDRII 64Mbyte Flash 16Mbyte Power input requirement Passive PoE 24V Pin 4,5 VDC+ Pin 7,8 VDC- Ethernet PHY 10/100 Mbps Antenna Antenna Frequency Band Vertical Port HPBW Horizontal Port HPBW Antenna Configuration LAN port Reset Button Internal 11 +/- 2 dbi directional antenna (Vertical, Horizontal) 5150-5250;5250-5470;5470-5725;5725-5850 MHz (XY Plane /H-Plane):67º; (XZ Plane /E-Plane):15º (XY Plane /H-Plane):87º; (XZ Plane /E-Plane):20º 2 * 2 (2 Tx,2 Rx) 1port Reset to factory default Ground Ground terminal x1 System Update Capability - Support Web-UI upgrade via Ethernet port or wireless network - Support TFTP upgrade via Ethernet port LED Definition Power (Single-color LED x1) Green On: Power / system on Green Off: power / system off LAN (Single-color LED x1) Off: No Ethernet connection detected Green On: Ethernet connection detected Green Blinking: Sending / receiving data 5G WLAN (Single-color LED x1) Green Off: WLAN disabled Green On: WLAN enable Green Blinking: WLAN data transmit Signal *3 (Single-color LED x3) Excellent: 3 LED Green ON Good: 2 LED Green ON Weak: 1 LED Green ON Data Rate 11a: 54M, 48M, 36M, 24M, 18M, 12M, 9M, 6Mbps auto fallback 11n: HT20 MCS0~15
HT40 MCS0~15 Data modulation type BPSK/QPSK/CCK/DQPSK/DBPSK 802.11a: OFDM 802.11n: OFDM RF frequency range 1 2 FCC: 5.15GHz~5.25GHz ; 5.725GHz~5.85GHz NCC: 5.15GHz~5.25GHz ; 5.725GHz~5.85GHz CE: 5.15GHz~5.35GHz ; 5.47GHz~5.725GHz Power Consumption (W) <12W Average Output Power @ 802.11a 25 Date 5150~5725MHz 5725~5850MHz (Single Chain) (± 2dBm) 3 Rate/Frequency 4 6, 9, 12, 18, 24Mbps 23dBm 20 dbm 36Mbps 22 dbm 20 dbm 48Mbps 21 dbm 20 dbm 54Mbps 20 dbm 20 dbm 802.11an At HT20 Date Rate/Frequency 5150~5725 MHz 5725~5850 MHz MCS0, MCS8 23dBm 20 dbm MCS1, MCS2, MCS3, MCS9, 23 dbm 20 dbm MCS10, MCS11 MCS4, MCS12 22 dbm 20 dbm MCS5, MCS13 21 dbm 20 dbm MCS6, MCS14 20 dbm 20 dbm MCS7, MCS15 19 dbm 19 dbm 1 Disable 5600~5650MHz due to Environment Canada weather satellites operating in the band are protected. 2 Disable 5250~5350MHz & 5470~5725MHz due to DFS band at FCC domain. 3 The listed value is the target power calibrated in the card. The actual power will vary depending on each country s regulation. For detailed CTL table settings please contact our sales representative. 4 The output power been measured from U.FL connector without RF cable loss.
Sensitivity (at single chain) 802.11an At HT40 Date Rate/Frequency 5150~5725 MHz 5725~5850 MHz MCS0, MCS8 21dBm 20 dbm MCS1, MCS2, MCS3, MCS9, 21 dbm 20 dbm MCS10, MCS11 MCS4, MCS12 21 dbm 20 dbm MCS5, MCS13 21 dbm 20 dbm MCS6, MCS14 20 dbm 20 dbm MCS7, MCS15 19 dbm 19 dbm Mode 11a 11n HT20 11n HT40 6Mbps -89 9Mbps -88 12Mbps -85 18Mbps -83 24Mbps -80 36Mbps -76 48Mbps -71 54Mbps -70 MCS 0/8-83 -80 MCS 1/9-80 -77 MCS 2/10-78 -75 MCS 3/11-75 -72 MCS 4/12-71 -68 MCS 5/13-67 -64 MCS 6/14-66 -63 MCS 7/15-65 -62
2.2 Firmware Specification The Firmware Specifications of ZAC-1023-5-13 as below, default wireless mode: FAP Function Catalog Detail Function Default settings Web Language English/Chinese English Status Information Connections Statistics ARP Table Bridge Table DHCP Client List Network Activity System Basic Settings: 1. Device Name 2. Country/Region 3. Device Mode Wireless Network Settings: Time Setting RADIUS Settings Firewall Setting (Router Mode Only) Basic Wireless Settings Table 2-2 Firmware Specification (Fat AP Mode) Network Mode Spanning Tree STP Forward Delay Enable 802.1Q VLAN Management VLAN ID WAN Access Type 1. Static IP 2. DHCP Client 3. PPPoE WAN IP Address LAN Access Type 1. Static IP 2. DHCP Client LAN IP Address DHCP Server DHCP Relay 1. Current Time 2. Time Zone Select 3. Enable NTP client update IP Address of Authentication RADIUS Server 1. Src IP Filtering 2. Dest IP Filtering 3. Src Port Filtering 4. Dest Port Filtering 5. Port Forwarding 6. UDP Pass-through 7. DMZ Disable Wireless LAN Interface Operation Mode AP Mode Function: apxxxxxx United States (for FCC) Bridge Enable 1 (second) 0 Static Manual, 192.168.0.99 Static Manual, 192.168.1.1 GMT 0.0.0.0 Unselected AP
1. SSID 2. Broadcast SSID 3. 802.11 Mode 4. HT Protect 5. Frequency/Channel 6. Extension Channel 7. Channel Model 1. 20MHz 2. 40MHz 8. Maximum Output Power 9. Date Rate 10. Channel Protection 1. 2. CTS to self 3. RTS-CTS Wireless Client Mode Function: 1. SSID 2. Lock AP MAC 3. 802.11 Mode 4. Channel Model 1. 20MHz 2. 40MHz 5. Maximum Output Power 6. Channel Protection 1. 2. CTS to self 3. RTS-CTS 7. Enable MAC Clone Bridge Mode Function: 1. 802.11 Mode 2. Frequency/Channel 3. Extension Channel 4. Channel Model 1. 20MHz 2. 40MHz 5. Maximum Output Power (per chain) 6. Data Rate 7. Channel Protection 1. 2. CTS to self 3. RTS-CTS AP Repeater Mode Function: 1. SSID 2. Broadcast SSID 3. 802.11 Mode 4. HT Protect 5. Frequency/Channel 6. Extension Channel 7. Channel Model 1. 20MHz 2. 40MHz Wireless Enabled 802.11a/n 5745MHz (149) 20MHz Full Auto Wireless 802.11a/n 20MHz Full 802.11a/n 5745MHz (149) 20MHz Full Auto Wireless Enable 802.11a/n 5745MHz (149) 20MHz
8. Maximum Output Power (per chain) 9. Date Rate 10. Channel Protection 1. 2. CTS to self 3. RTS-CTS Profile Settings 1. VAP Profile Settings (up to 8 profiles) Full Auto In Each Profile: Basic Settings 1. Profile Name 2. SSID 3. Broadcast SSID 4. Wireless Separation 5. WMM 6. Station Number Limitation 7. Max. Station Num 8. VAP VLAN ID 9. IGMP Snooping Profile1~8 Wireless Enabled Enabled 32 0 Enabled Security Settings 1. Open System Open System 2. Shared Key(64/128/152-bits WEP) 3. Legacy 802.1X 4. WPA 5. WPA2 6. WPA + WPA2 7. WPA-PSK(TKIP) 8. WPA2-PSK(AES) 9. WPA-PSK + WPA2-PSK Advanced settings A-MPDU Aggregation Enabled A-MSDU Aggregation Short GI Enabled RTS Threshold(256~2347) 2347 Fragmentation Length(256~2346) 2346 Beacon Interval(40~3500ms) 100 DTIM Interval (1-255) 1 Preamble Type Auto IGMP Snooping Enabled Distance 1000 (m) Channel Protection (/CTS to self/rts-cts) Access Control Support up to 32 MAC addresses for each profile with modes below: 1. Disable 2. Allow Listed 3. Deny Listed Traffic Shaping 1. Overall Traffic Shaping 1. Incoming Traffic Limit
Manageme nt Remote Management Configuration Management 2. Incoming Traffic Burst 3. Outgoing Traffic Limit 4. Outgoing Traffic Burst 2. VAP Traffic Shaping (per VAP profile) 1. Outgoing Traffic Limit 2. Outgoing Traffic Burst Embedded Web Configuration Interface 1. HTTP 2. HTTPS 3. SSL Remote Console 1. Telnet 2. SSH 3. FTP SNMP Management 1. V1 (RFC 1157) 2. V2c (RFC 2011-2013) 3. V3 (RFC 2571-2576) 4. SNMP trap transmit Capability to store configuration backup Configuration changes via: 1. Local command line 2. Remote command line (SSH) 3. Load config file 4. Web interface Configuration to Restore factory (or service provider) defaults via: 1. Web 2. Push button FTP WISE (Windows-based Utility Software) CPE Management HTTP Telnet V2 Enabled Firmware Upload Upgrade Device s Firmware Configuration File 1. Backup and Restore Configuration 2. Reset Settings to Factory Default 3. Reboot Device Password Settings Change Password password Certificate Settings Import / Delete User s Certificate Files for Wireless Client Mode s User Authentication (802.1X, WPA, or WPA2) Tools System Logs Syslog (RFC 3164) Support Site Survey Ping Watchdog Wireless Network (AP) Scan Tool Enable Ping Watchdog IP Address to Ping Ping Interval Startup Delay Failure Count To Reboot 0.0.0.0 300 Seconds 100 Seconds 300
2.3 Power Adapter Specification 2.3.1 Input Voltages and Frequency 2.3.2 Output Voltage, Current and Ripple 2.4 Physical specification The Physical specifications of the product are as below: Table 2-4 Physical Specification Items Description Dimension 205mm(L) 64mm(W) 61mm(H) Weight 500g Enclosure IP55 2.5 Environment specification The Environment specifications of the product are as below: Table 2-5 Environment Specification Items Device Description Power Adapter Spec Operating Temperature(Max) -20 ~ +70 C 0 ~ +40 C Operating Humidity (non-condensing) 10 to 95% RH 20 to 85% RH Storage Temperature -40 ~ +70 C -20 ~ +60 C Storage Humidity (non-condensing) 10 to 95% RH 5 to 95% RH
Warranty Green 24 Months RoHs /REACH Compliant
2.6 Safety/Country Approval We will do EMI/EMC certificate according to the following items: Table 2-6 Safety/Country Approval Items Description ID number FCC CE NCC Part15 sub B +ICES003 Part15 sub E EN301893 V1.7.1 EN 301 489-1 V1.9.2/EN 301 489-17 V2.2.1 EN 300 328 V1.8.1:2012 EN 55022 / EN 55024 EN 60950-1:2006+A11:2009+A1:2010+A12:2011 EN 60950-22 IP55 Report ErP WEEE LP0002 FCC ID : M4Y-ZAC10235IO 2.7 Packaging Specification The following items will be required for the complete packaging of the ZAC-1023-5-13: Table 2-7 Package Item Comments Carton Gift Box / Cushion ZAC-1023-5-13 Power Supply PoE injector Steel Cable Tie Suitable size to fit in Suitable size to fit in Whole product should be in a protective bag Appropriate adapter based on the region Suitable size to fit in Suitable size to fit in
3 Mechanical Spec 3.1 Housing Outline Drawing
4 Pin Assignment Spec Item RJ-45 PCB Jack 1Port Description & Pin Assignment Pin NO. Signal Name Pin Definition (ETH) 1 RX+ Receive(+) 2 RX- Receive(-) 3 TX+ Transmit(+) 4 24V + Power Supply 5 24V + Power Supply 6 TX- Transmit(-) 7 GND GND 8 GND GND RS232 1PORT-4Pin (RS232) Pin NO. Signal Name Pin Definition 1 VCC 3.3V 2 GND GND 3 UART_SOUT UART_TX 4 UART_SIN UART_RX
(Reset) Pin NO. Signal Name Pin Definition 1 AR9342_RES AR9342_RES 2 GND GND 3 FGND FGND 4 FGND FGND