Upgrading using TRUMP New version of TRUMP has been released to support Tranzeo WiFi radio product binaries up to and including version 5.0.7. TRUMP is Tranzeo s Remote Upgrade Management Program, which can allow you to locate and mass upgrade your network from a single tool. NOTE: It is recommended that you uninstall any previous versions of TRUMP before upgrading to TRUMP Version 1.0.8-fw-5.0.7. You also should delete the C:\Program Files\Tranzeo\Trump folder manually. This is to ensure that the new settings are correctly applied. Please consult the Install Guide for TRUMP-1.0.8-fw-5.0.7.pdf file for step-by-step installation/uninstall instructions, and on how to use it to upgrade your radios. CHANGES IN TRUMP 1.0.8-FW-5.0.7 Added released version 5.0.7 binaries for TR-CPQ, TR-SL2, TR-SL5, TR-SL9, TR-6, TR-5a, TR- FDD, TR-4.9, TR-Multi, and TR-90X KNOWN ISSUES TR6000/TR5a and TR-49 models running firmware < 4.0.2 will need to upgrade to 4.0.5 first, and then to 5.0.7 Need to uninstall previously installed versions of Trump prior to installing this release Need to manually delete C:\Program Files\Tranzeo\Trump folder after uninstall to ensure new changes are used Installing on a system with ActivePERL can lead to TrLocator /TRUMP scan failures, especially when using remote desktop to access the machine running TRUMP. Workaround: Uninstall ActivePERL. You can download the latest version of TRUMP from the Tranzeo Support Website. Victor 2.5 The Tranzeo Victor Program is a utility that allows users to locate and quickly change the IP address of Tranzeo radios. It sends out a broadcast on the network and displays a list of all Tranzeo radios and their corresponding IP addresses. This program replaces the Tranzeo Locator. Victor 2.5 is the latest release. You can download the latest version of Victor from the Tranzeo Support Website. Page 2 of 7 2010-10-21
Firmware Release Notes CHANGES IN 5.0.7 UI: Changed Frames over 1518 and less than 2048 bytes to Frames over 1544 and less than 2048 bytes on Ethernet statistic page Bug Fixes: [902] Fixed power cap per modulation bug introduced in 5.0.6 CHANGES IN 5.0.6 New Features: Amended 5.8GHz band for India CHANGES IN 5.0.5 UI: [1158] Changed label Enable VLAN to Enable MGMT VLAN on network advanced page New Features Added: Amended 900MHz band for Brazil. Based on customer request, added an option to make the web port changeable in bridge mode. Added support for 4I Cards. Bug Fixes: Optimized code to fix memory leak in TCP module, which caused a hard lock-up when accessing web port with DDOS type requests (attempting thousands of simultaneous logins). This behavior was triggered by bugs in some monitoring software. While the issue was extremely rare, it is recommended that all user upgrade to eliminate any chance of this issue. Optimized code to fix a small memory leak in Web Server module, which caused system crash and hard lock-up when accessing web port with DDOS type requests. This issue was found when investigating the above issue. There were no field reports of this issue. Fixed WPA group key update issue which caused CPE's decryption failure for broadcast packets. Removed debug output on dongle console (not visible to customer). Page 4 of 7 2010-10-21
[1424] Power LED does not turn back on until power cycle when re-enabling signal LEDs. MIBS: The following private Tranzeo MIB s were added:.iso.org.dod.internet.private.enterprises.tranzeo.stationstat.stnnumber (number of associated stations).iso.org.dod.internet.private.enterprises.tranzeo.assocstation.stnipaddr (associated station IP).iso.org.dod.internet.private.enterprises.tranzeo.assocStation.stnMacAddr (associated station Mac address) Please refer to the updated MIB V0.6 for more details. You can download the latest MIB from the Tranzeo Support Website. CHANGES IN 5.0.4 UI: Fixed menu border color (IE7 does not support 'grey', must be 'gray') Enable auto scroll for TABs frame so that it can be displayed for small screen (IPOD) FDD Specific Changes [1178] Enable VLAN setting on Network Advanced page NAT MODE CHANGES [1245] New Feature. NAT Connections Timeouts changed to more aggressive values on the CPQ/SL2 series Previous Type New 60 ICMP 10 300 UDP 10 120 TCP SHORT 60 7800 TCP LONG 7800 20 TCP Reset 20 240 others 10 NAT MODE CHANGES Added the ability to alter the NAT Connections Timeout values to Network Configuration, Advanced Tab. Please note that this option only appears if radio is in Router mode. Page 5 of 7 2010-10-21
CHANGES IN 5.0.3 NO USER CHANGES 5.0.3 was created solely to facilitate changes on Tranzeo s Production Line. There are no feature differences between 5.0.2 and 5.0.3. CHANGES IN 5.0.2 UI CHANGES: Split configuration into Basic and Advanced tabs on the following pages: o Wireless Settings o Administrative Settings o Encryption o Statistics o Network Configuration Disabled option WPA Update Interval in CPE mode since it is AP controlled option Interface now removes trailing spaces at the end of SSID automatically; when saving an SSID, and when clicking on an AP with a trailing SSID on AP List o Upgrade will not automatically change SSID containing trailing spaces, but any configuration applied at firmware 5.0+ will remove trailing SSID. o Removes trailing spaces when importing configuration settings Added IP address hyperlink on AP's Stations List page to open CPE s HTTP Interface in new tab Updated System Performance page to prevent memory leak in IE7 and Firefox 3.5 browser. Leak occurred on client PC, not in radio. Wireless Performance page now refreshes the RSSI value Added pop up message box informing user of "Re-associate on new IP" feature may not be compatible with non-tranzeo AP's when in DHCP client mode Added Numbers to the WEP Key boxes Now display system uptime on Information page. o PxP mode has additional link uptime. Note: FDD may be off up to 6 seconds due to polling HTTP Interface now prevents 0.0.0.0 from being set as the default route. This prevented the DHCP gateway option from being set in DHCP client mode in firmware 4.0.5 Changed Network mode drop down box to be compatible with Chrome browser Fixed ARP Table page to clear IP address column when last page isn't completely filled Combined Configuration page for bridge/router mode NEW FUNCTIONS ADDED: Added feature to block DHCP servers behind bridged CPEs from serving other clients on the AP Added configuration settings to autoconfig function: o net.reverse_dhcp_block (new) o net.shaping_rate (new) o net.shaping_policy (new) o net.router.qos.uplink_speed (value range changed) o net.shaping_policy (new) Implemented a TCP throughput test, requires throughput.exe, a Windows Command line tool. o TCP server mode enabled all the time and supports wireless or wired upstream and downstream. Usage: TCP input test (sending data IN to device) throughput.exe -i -r [seconds] [ip_of_radio] Page 6 of 7 2010-10-21
TCP output test {receiving data OUT of device) throughput.exe -o -r [seconds] [ip_of_radio] Added a basic traffic shaping feature to shape traffic transmitted from the device: o Enabled by default with unlimited default value Works in Bridge mode, but doesn't have the QoS classification feature o Router mode still has the QoS classification feature o Shaping applies to aggregate throughput, so for an AP, a setting of 10000 kbps would be shared amongst all CPEs, not per CPE o o Added ability to set numerical traffic limit instead of fixed rates QoS enabled AP will not have Shaping enabled on upgrade, but QoS enabled CPE in router mode will be converted to numerical traffic limit and remain enabled Firmware now returns the firmware version in Victor response Added IP address hyperlink on AP's Stations List page to open CPE in new tab Enabled 1/4 and 1/2 channel support for card type 6C Radio now checks before process files in case users accidently tries to import a firmware image instead of settings file Display system uptime on Information page. o PxP mode displays additional value of Link Uptime. Note: FDD may be off up to 6 seconds due to polling MODELS SPECIFIC ENHANCEMENTS: [FDD] Added slave board status and added client stats MODELS SPECIFIC BUG FIXES: [FDD] Fixed MAC address validation in pxp MAC address fields [900] Fixed stability issue when configuring 1/4 channel in pxp mode Please refer to the General Firmware Changes document for older firmware changes. Page 7 of 7 2010-10-21