Wiring Diagram and Programming Instructions for MAW6 Digital Keypad and Proximity Card/F reader www.grantsautomation.com.au grant@grantsautomation.com.au
Wiring Diagrams for MAW6 Digital Keypad For Pedestrian Gates fitted with an electric Strike Lock or magnetic Lock Maw6 Digital Keypad/Touch Tag Reader BuzzA Pink BuzzB Pale Blue WG DO Green WG D1 White Alarm Grey Exit P/B Yellow or In Brown 9 to 28VDC Red Black NO Blue COM Purple NC Orange Alarm Exit Electric Strike Lock 12VDC Magnetic Lock 12VDC 12VDC Power Supply Can be unregulated with an output between 9V and 28VDC or Exit Button will activate the Devices output timer in the same manner that entering a correct code or touching a programmed tag or card does. Ideal as a way for pedestrians to exit without a code. or In is for a magnetic reed or micro switch fitted to a gate to activate an alarm if not closed in 1 minute after use. For 12V Automatic Gate Operator or 240V Operator with 12VDC output for accessories. BuzzA Pink Maw6 Digital Keypad/Touch Tag Reader BuzzB Pale Blue WG DO Green WG D1 White Alarm Grey Exit P/B Yellow or In Brown 9 to 28VDC Red Black NO Blue COM Purple P/B in P/B com 12V out Automatic Gate Operator Control Board NC Orange
Wiring Diagrams for MAW6 Digital Keypad For 24V Automatic Gate Operator or 240V operator with 24VAC or DC output for accessories. Maw6 Digital Keypad/Touch Tag Reader BuzzA Pink BuzzB Pale Blue WG DO Green WG D1 White Alarm Grey Exit P/B Yellow or In Brown 9 to 28VDC Red Black NO Blue COM Purple NC Orange P/B in P/B com 24V~ out 24V~ in 12V out Automatic Gate Operator Control Board VC12V Voltage Converter For Access Control/Alarms system Maw6 Digital Keypad/Touch Tag Reader BellA Pink BellB Pale Blue WG DO Green WG D1 White Alarm Grey Exit P/B Yellow or In Brown 9 to 28VDC Red Black NO Blue or Bell Alarm D0 D1 12V out Access Control/Alarm COM Purple NC Orange
Programming Instructions for MAW6 Digital Keypad and Card reader FEATURES: Up to 2000 User Codes (4 Digits), touch tags or cards all with a seperate user ID number so they can be removed even if tag or card is lost or code is forgotten. te: need to keep a log book Can use Code or Tag/Card or Code Tag/Card for extra security Activation time from 0 to 99 seconds. Users can change their own Code or Card without Master Code Keypads give a visual as well as acoustic signaling while entering codes PROGRAMMING: To Add a User Code or Tag/Card by ID To Add many Tags/ Cards To Remove a User Code or Tag/Card by ID press 1 press 1 press 2 Enter <User ID Number># 1 to 2000 Swipe Tag/Card Enter <User ID Number># 1 to 2000 will beep beep beep if this user already has a code or card sec if Tag/Card OK or beep beep Enter <User Code># (4 digits) or Swipe Tag/Card Add more? remove more? sec if Code or Card OK or beep beep programming mode programming mode Add more? programming mode www.grantsautomation.com.au grant@grantsautomation.com.au
PROGRAMMING: To Remove a Tag/Card with Tag/Card press 2 Swipe Tag/Card Set Tag/Card only Option press 30 # programming mode Set Tag/Card OR Code Option (default) press 32 # programming mode remove more? programming mode To Remove all User Codes or Tags/Cards Set Tag/Card & Code Option press 31 # programming mode To Change Activation Time press 4 Enter time in seconds from 0 to 99 YELLOW LED goes GREEN for 1/2 sec if OK or beep beep beep if not OK press 20,000 # programming mode programming mode www.grantsautomation.com.au grant@grantsautomation.com.au
Programming Instructions for MAW6 Digital Keypad To Change a User Code To Change the Master Code Restoring Settings. Enter <User ID Number># Enter <old User Code> # Enter <new User Code># (4 digits) Enter <new User Code># (4 digits) to confirm YELLOW LED goes GREEN for 1/2 sec if OK or beep beep beep if not OK press 0 Enter <new Master Code># (6 to 8 digits) Enter <new Master Code># (6 to 8 digits) to confirm YELLOW LED goes GREEN for 1/2 sec if OK or beep beep beep if not OK The factory settings can be recovered it necessary without loosing any user codes, tags or cards programmed in. To do this remove power from the device, then after 15 seconds press and hold the # key and restore power. When the decive beeps left go of the # key as the factory settings have been restored. programming mode programming Record Master Code Here: mode Record User ID numbers and Codes Here: User Name and/or Description User ID Number User Code www.grantsautomation.com.au grant@grantsautomation.com.au