500-006 cisco Number: 500-006 Passing Score: 800 Time Limit: 120 min
Question Set 1 QUESTION 1 How many conferencing bridges can a single full-capacity Cisco TelePresence Conductor support? A. 1 B. 10 C. 15 D. 25 E. 30 F. 104 G. 500 H. 2400 Correct Answer: E QUESTION 2 In the Cisco TelePresence Conductor web pages, which logs can you view? A. system log, event log, and CDR log B. system log and event log C. event log and configuration log D. system log, event log, configuration log, and CDR log Correct Answer: C QUESTION 3 A user complains that their rendezvous conference fails to connect. What should the administrator check on the Cisco TelePresence Conductor?
A. NTP is working correctly. B. The auto-dialed participant is defined for that user. C. H.323 is enabled on the System Administration page. D. The conference bridge has an Active status. Correct Answer: D QUESTION 4 What are the system components of provisioning? A. Cisco VCS, Cisco TMS, and Cisco Jabber B. Cisco VCS and Cisco TMS C. Cisco VCS, Cisco TMS, and Cisco TMSPE D. Cisco VCS, Cisco Unified CM, Cisco TMSPE E. Cisco VCS, Cisco Unified CM, Cisco TMS, and Cisco TMSPE Correct Answer: C QUESTION 5 Which four licenses and option keys are required in order to provision and register a Cisco Jabber Video for TelePresence client? (Choose four.)
A. Cisco TMS: Jabber Video capacity option key B. Cisco TMS: direct managed system licenses C. Cisco Jabber: user licenses D. Cisco VCS: Device Provisioning option key E. Cisco VCS: Registration license BDE QUESTION 6 What are the minimum required configuration settings for the provisioning Root folder? A. phone book URI, presence server URI, SIP server address B. Maximum In bandwidth, Maximum Out bandwidth, SIP server address C. network DNS domain name, Maximum In bandwidth, Maximum Out bandwidth D. network IPv4 address, network DNS domain name, SIP server address QUESTION 7 Which three directory services can import Cisco TMS users? (Choose three.) A. Active Directory B. Active Directory with Kerberos (Secure AD) C. Novell edirectory D. Lightweight Directory Access Protocol BD
QUESTION 8 If provisioning replication fails for any reason, what should be done to determine the cause of the failure? A. Re-install the Cisco Jabber Video client and try again. B. Run all diagnostic tests on the TMS PE Diagnostics page. C. Capture Cisco TelePresence Jabber Video logs and find the problem. D. Run a Wireshark trace on the communication between the Cisco Jabber Video client and the Cisco VCS. Correct Answer: B QUESTION 9 Which option is related to the error "Unable to communicate with the TMS Provisioning Extension service"? A. The correct option key is not installed. B. HTTPS is not configured. C. The certificate is invalid. D. Cisco TMSPE service needs to be restarted or is not running. Correct Answer: D QUESTION 10 Which three endpoints are provisioned by Cisco TMSPE? (Choose three.) A. Cisco TelePresence System MX Series
B. Cisco TelePresence System EX Series C. Cisco Unified IP Phone 9971 D. Cisco Unified IP Phone 7960 E. Cisco TelePresence System CTS 500 BE QUESTION 11 What occurs when a conference with eight sites is booked through Cisco TMS? A. TMS will automatically choose the most appropriate MCU that is available on the network. B. TMS will prompt the engineer to book an MCU on the network. C. TMS will cascade the call by using the built-in MultiSite capabilities of the endpoints. D. TMS will automatically activate Multiway. QUESTION 12 Which persistent setting other than system name, E.164 alias, and H.323 ID is configurable for a personal video system? A. SIP URI B. MAC address C. serial number D. IP address
QUESTION 13 What is the purpose of the ISDN and the IP zones in Cisco TMS? A. To configure the neighboring of gatekeepers B. To configure subzones, links, and pipes in gatekeepers C. To display systems correctly in the map mode D. To perform call routing Correct Answer: D QUESTION 14 All Cisco TMS users and administrators are members of which default group? A. users B. video unit administrator C. site administrator D. administrator QUESTION 15 Which is the recommended method for backing up and restoring the SQL database? A. The TMS Tools application on the Cisco TMS server B. The SQL command-line editor
C. Microsoft SQL Server Manager Studio Express D. SQL command-line scripting Correct Answer: C QUESTION 16 What happens if Cisco TelePresence VCS Control only has an 'AnyIPAddress' search rule configured in the traversal zone? A. All calls from the Expressway won't work B. All calls to the Expressway won't work C. Calls dialed with an alias from the Expressway won't work D. Calls dialed with an alias to the Expressway won't work Correct Answer: D QUESTION 17 Refer to exhibit. Exhibit:
You started a conference without Cisco TMS and you want to monitor the conference. Which setting will enable you to monitor the conference? A. Show MCUs B. Show Ad Hoc C. Expand the Active folder D. Expand the Reservations folder
E. Add to Watch List Correct Answer: B QUESTION 18 On which three operating systems can you install Cisco TMS? (Choose three.) A. Windows Server 2003 SP1 or later, 32-bit B. Ubuntu 12.04 LTS C. RHEL D. Windows Server 2008 SP2 or later, Standard 32-bit and 64-bit E. Windows Server 2008 R2 SP1 or later, Standard 64-bit F. Windows Server 2003 R2 G. Solaris H. CentOS DE QUESTION 19 The following Cisco TMS warning is displayed. "No route possible between X and Y." What does this warning indicate? A. One of the endpoints is not registered on the Cisco TP VCS. B. There is a restriction that does not allow calls between zones. C. TMS cannot find one of the selected systems. D. Gateway is not available. Correct Answer: B
QUESTION 20 What is the effect of registering the Cisco TCS with the Cisco VCS using H.323 gateway mode? A. The Cisco TCS does not support this type of registration. B. An unlimited number of recording aliases can be assigned. C. The Cisco TCS is prevented from making an outbound call to a Cisco MCU. D. The Cisco TCS can traverse calls between SIP and H.323. Correct Answer: B QUESTION 21 Which of these constitutes a Cisco TCS recording alias? A. a recording template, a media server configuration, and a call configuration B. a media server configuration and a call configuration C. a recording template and a media server configuration D. a recording template and a call configuration QUESTION 22 Which two statements about Cisco TCS users are true? (Choose two.) A. Users with the creator role can create their own recording aliases.
B. Local users have only limited Cisco TCS permissions. C. Users can be assigned to the Cisco TCS through an Active Directory LDAP server. D. User permissions are based on one of three assignable roles. Correct Answer: CD QUESTION 23 Which two pieces of troubleshooting information does the Cisco TCS provide? (Choose two.) A. log messages that can be accessed by the site manager through the CLI B. recording alias processing progress C. error logs that only Cisco TAC can access D. log messages that can be accessed by the site manager through the web interface Correct Answer: BD QUESTION 24 What does an MCU service prefix of 8 mean for users of a Cisco TelePresence MCU? A. Any conferences created from an endpoint will be prefixed with 8. B. Any dialed number starting with 8 will be routed to the MCU. C. Any gateway services will be prefixed with an 8. D. Any MCU-created conferences will start with an 8. Correct Answer: B
QUESTION 25 What does an endpoint system use to navigate the Auto Attendant menu on the Cisco TelePresence MCU? A. FECC and DTMF navigation B. a special remote that came with the Cisco TelePresence MCU C. only FECC, DTMF is not supported D. web interface of the endpoint QUESTION 26 What software can you use to customize the banner on the Cisco TelePresence MCU? A. SSH terminal client B. web browser C. WinSCP client D. customization software Correct Answer: B QUESTION 27 A customer wants to allow users to create ad hoc conferences by dialing the Cisco TelePresence MCU service prefix of 8, followed by a number for the conference. Which global conference settings allow the customer to do this? A. Media port reservation: Disabled Incoming calls to unknown conferences or auto attendants: Create new ad hoc conference Register ad hoc conferences with gatekeeper: On B. Media port reservation: Enabled Incoming calls to unknown conferences or auto attendants:
Default auto attendant Register ad hoc conferences with gatekeeper: Off C. Media port reservation: Enabled Incoming calls to unknown conferences or auto attendants: Create new ad hoc conference Register ad hoc conferences with gatekeeper: Off D. Media port reservation: Disabled Incoming calls to unknown conferences or auto attendants: Default auto attendant Register ad hoc conferences with gatekeeper: On QUESTION 28 Why would an endpoint stop sending 720p in a call with a Cisco TelePresence MCU? A. The endpoint Ethernet speed renegotiated at half-duplex. B. The Cisco TelePresence MCU is using video to receive bit rate optimization to request a lower bandwidth. C. Another endpoint joined the conference, which brought the conference rate down. D. Another endpoint failed in its negotiation with the Cisco TelePresence MCU. Correct Answer: B QUESTION 29 Which command is used to set the IP configuration for a Cisco TelePresence MCU? A. status <IP address> <netmask> <default GW> <DNS server address> B. xconfigure <IP address> <netmask> <default GW> <DNS server address> C. static <IP address> <netmask> <default GW> <DNS server address> D. set <IP address> <netmask> <default GW> <DNS server address> Correct Answer: C
QUESTION 30 How do you know that all blades on the Cisco TelePresence MSE 8000 have booted correctly? A. The logo will light up. B. The lights on the fan tray will turn green. C. The light in the supervisor blade will turn green. D. Alarm lights come on. Correct Answer: B QUESTION 31 A Cisco TelePresence MCU Auto Attendant does not allow users to set up ad hoc conferences, even though the media port reservation setting is off. What may cause this problem? A. The streaming option was selected instead of the ConferenceMe? option. B. The global conference setting, auto-attendant, is not set up correctly. C. The user endpoint does not have MultiSite? installed. D. The auto-attendant has not been set up correctly. Correct Answer: D QUESTION 32 Which three methods can an engineer use to upgrade the software on the Cisco TelePresence MCU? (Choose three.) A. web interface
B. FTP C. flash drive D. SSH E. serial interface F. RMA the unit G. Telnet BC QUESTION 33 Which three protocols does Cisco TelePresence Server support? (Choose three.) A. SCCP B. H.323 C. H.460 D. TIP E. SIP Correct Answer: BDE QUESTION 34 When the administrator enables remotely managed mode on the Cisco TelePresence Server, which statement is correct? A. Cisco TelePresence Conductor can communicate with the TelePresence Server. B. Cisco TMS is able to gather CDR data. C. SNMPv3 is used as a secure communication channel to the management device. D. Cisco Unified Communications Manager can communicate with the TelePresence Server.
QUESTION 35 A Cisco 5310 MCU is being configured as an ad hoc conference bridge in Cisco Unified Communications Manager. Which two configuration steps must be completed for this to function correctly? (Choose two.) A. Install the Cisco Unified Communications Manager feature key on the MCU. B. Create a SIP trunk from Cisco Unified Communications Manager to the MCU. C. Enable Media Port Reservation on the MCU. D. Disable H.323 and enable SIP on the MCU. Correct Answer: CD QUESTION 36 What is required for Cisco TelePresence Server to communicate with Cisco WebEx, using the PSTN? A. Cisco TelePresence MCU 5300 B. Cisco 3420 ISDN Gateway C. third-party interop key D. Web Conferencing feature key Correct Answer: C QUESTION 37
Endpoints can be placed into different Cisco TelePresence VCS (X5 or above) subzones according to which of the following? A. aliases or IP addresses B. aliases and MAC addresses C. IP addresses only D. aliases, MAC addresses, and IP addresses QUESTION 38 Which Cisco TelePresence VCS function can you use to control the speed of a call within the same subzone? A. links B. pipes C. per-call bandwidth D. default bandwidth Correct Answer: C QUESTION 39 Two Cisco TelePresence VCSs are not configured with DNS. What are the consequences of only setting up one neighbor zone? A. Calls can only be made in one direction. B. All searches will fail between neighbors. C. Calls are not possible between neighbors. D. Registrations are not possible.
QUESTION 40 What does the hop count setting on the firewall traversal configuration limit on the Cisco TelePresence VCS? A. The number of Cisco TelePresence VCSs that a call can travel through. B. The number of firewalls that a call can travel through. C. The number of routers that a call can travel through. D. The number of switches that a call can travel through. QUESTION 41 When can a transform rule be applied on a Cisco TelePresence VCS? A. searches, inter-zone and inter-subzone calls B. searches and inter-zone calls C. searches and inter-subzone calls D. inter-zone and inter-subzone calls Correct Answer: B QUESTION 42 How will FindMe help a user working from either home or the office?
A. Anyone can contact the user using a single identity. B. Users can locate any individual in the company using the address book. C. Users can change their system names according to their current location. D. Anyone can contact the user by giving each endpoint the same configuration. QUESTION 43 Which Cisco TelePresence VCS function is used to enable H.323 endpoints to connect to SIP endpoints? A. zones B. subzones C. TURN D. interworking Correct Answer: D QUESTION 44 What information about a change can you determine from the configuration log on a Cisco TelePresence VCS? A. the E.164 alias of the person who made the change B. the IP SIP address of the person who made the change
C. the H.323 ID of the person who made the change D. the username of the person who made the change Correct Answer: D QUESTION 45 What do you need to do in order to prevent browsers from generating warnings about certificates when they access the Cisco TelePresence VCS? A. Install a certificate from a trusted certificate authority. B. Install a certificate from the TAC. C. Disable certificates on the Cisco TelePresence VCS. D. Disable the CPL scripts from running to check security. QUESTION 46 Which feature must be enabled on the Cisco TelePresence VCS in order to monitor the status of non-presence-enabled clients? A. Presence User Agent B. interworking C. FindMe? D. LDAP
QUESTION 47 What does it mean when an endpoint is Multiway-enabled? A. Endpoints can transfer calls from one endpoint to another. B. Endpoints can make simultaneous SIP and H.323 calls. C. Endpoints can deliver three or more streams of video. D. Endpoints can escalate calls to an MCU. Correct Answer: D QUESTION 48 What will happen if you make configuration changes to a VCS peer in a cluster that is not the master? A. The peer will not allow the changes to be saved. B. The changes will propagate to other peers, including the master. C. The master will overwrite the changes. D. The peer will hold the changes but not synchronize the changes to the master. Correct Answer: C QUESTION 49 In which order will pre-search operations occur on a Cisco TelePresence VCS? A. Transforms, Call Policy, User Policy B. Call Policy, User Policy, Transforms C. User Policy, Call Policy, Transforms D. Transforms, User Policy, Call Policy
QUESTION 50 How many peer relationships are required to implement a hierarchical dial plan for a network of 6 regional VCS controls? A. 1 B. 2 C. 6 D. 15 Correct Answer: C QUESTION 51 Which statement is true about the registration restriction policy within the Cisco TelePresence VCS? A. Allow lists allow all registrations except those listed, Deny lists deny all registrations except those listed. B. Allow lists allow all registrations except those listed, Deny lists allow all registrations except those listed. C. Allow lists deny all registrations except those listed, Deny lists allow all registrations except those listed. D. Allow lists deny all registrations except those listed, Deny lists deny all registrations except those listed. Correct Answer: C QUESTION 52 Which statement is correct about the configuration of the call control device?
A. The Cisco TelePresence Management Suite can auto-provision the dial plan between the Cisco VCS and Cisco Unified Communications Manager, using CDP. B. The Cisco Unified Communications Manager dial plan only supports numeric values. C. The Cisco VCS and Cisco Unified Communications Manager can pass dial plan information between them to create a single directory based on an H.350 schema. D. The Cisco VCS and Cisco Unified Communications Manager support numeric and URI dialing. Correct Answer: D QUESTION 53 What needs to be configured for Endpoint A, registered to Cisco Unified Communications Manager, to dial Endpoint B, registered to Cisco VCS? A. An IPsec VPN tunnel needs to be configured. B. A SIP trunk needs to be configured. C. A Cisco VCS directory needs to be configured. D. A dedicated UCM subscriber needs to be configured for the Cisco VCS. Correct Answer: B QUESTION 54 How many Cisco VCSs can be in a single cluster? A. 1 B. 2 C. 3 D. 4 E. 5 F. 6
G. 7 H. 8 Correct Answer: F QUESTION 55 In which three areas can the Cisco VCS be configured to use an external policy server? (Choose three.) A. CLI policy B. interworking configuration page C. search policy D. call policy E. registration policy F. Conference Factory G. Cisco Unified Presence configuration page Correct Answer: CDE QUESTION 56 A Cisco VCS has a search rule that uses the pattern string of ([78]\d1\d+ Meet\..*). Which three dial strings will match the search rule? (Choose three.) A. meet.richard B. 7881000 C. Meet.Richard D. 8881888 E. 781 F. 781.meet.richard G. 881000
CG QUESTION 57 What two protocols are used in firewall traversal? (Choose two). A. SIP B. H.239 C. H.460.18 & 19 D. Assent E. H.264 Correct Answer: CD QUESTION 58 What will happen if the local zone on a Cisco TelePresence VCS does not have a search rule? A. Calls to locally registered devices will fail. B. Calls from locally registered devices will fail. C. Calls to externally registered devices will fail. D. Calls from externally registered devices will fail.
QUESTION 59 How can you independently restore the default links on a Cisco TelePresence VCS? A. with an xcommand from the API B. by performing a factory reset C. from the bandwidth configuration section of the web interface D. by performing a reboot QUESTION 60 What should you use to back up the configuration of a Cisco TelePresence VCS (X5 software or above)? A. the backup and restore tool B. the serial port and the backup command C. the serial port and the xbackup command D. SCP to download the file called "backup.tft" QUESTION 61 Which troubleshooting tools are available on the Cisco TelePresence VCS (X5 or above)? A. configuration logs for all endpoints registered, endpoint status logs, and Cisco TelePresence MCU conference reports B. system resources, call history, search history, zone and subzone status, warnings, event logs C. H.323, SIP, and ISDN syslogs for each endpoint registered, all logs for all calls on the network D. searches, locate tools, check rules, syslog, call history, current calls, call logs from the endpoints
Correct Answer: B QUESTION 62 Where do you find the Clusterwide Domain Configuration? A. System > Enterprise Parameters B. System > Enterprise Phone Configuration C. Device > Trunk D. User Management > SIP Realm QUESTION 63 Where do you change the Maximum Session Bit Rate for Video Calls? A. Device > Trunk B. System > Location C. Media Resources > Media Resource Group D. System > Enterprise Parameters E. System > Region Correct Answer: E