Exam Questions 500-006 Implementing Cisco TelePresence Video Solution - Part 2 https://www.2passeasy.com/dumps/500-006/
Question No : 1 Which Cisco TelePresence C Series Codec command will move the on-screen display to monitor output 4? A. configuration video osd output: 4 B. xconfiguration video osd output: 4 C. command video osd output: 4 D. xcommand video osd output: 4 TC 7.2 Admin Guide Video OSD Output Define on which monitor the on-screen menus, information and icons should be displayed-the OSD (On Screen Display) is where you find trig menus, dialogs, icons and indicators, and the navigation is done with a remote control. Requires user role: ADMIN Value space: Question No : 2 Which menu on the Cisco TelePresence VCS should you refer to in order to verify that an endpoint has registered? A. Application B. Status C. Security D. Configuration The Registrations by device page (Status > Registrations > By device) lists each device currently registered with the VCS, and allows you to remove a device's registration. If the VCS is part of a cluster, all registrations across the cluster are shown. Note that an H.323 device can register with more than one alias; in such cases this page will show only one alias and (when present) one E. 164 number for that device. Note also that a single device can support both the SIP and H.323 protocols; in such a case the SIP registration and the H.323 registration will appear as separate entries on this page. Question No : 3 After you change the IP address of a Cisco TelePresence Codec C90, you are unable to use Telnet or a browser to connect to that address. However, you are able to use ping to connect to the new address. What are the two possible causes? (Choose two.) A. The configuration failed and there is another device with the same address that responds to the ping.
B. The codec disabled the Telnet and HTTP services after the IP address change. C. The codec needs to reboot after the IP address change in order to bind the services to the new address. D. The gatekeeper configuration failed and you need to set up the gatekeeper address and the discovery type again. Answer: A,C Question No : 4 The camera remote control is not responding. What can an engineer check in order to determine if the camera remote control or the system is causing the problem? A. The monitor is on the right channel. B. The switch inside the remote control is switched on. C. The light flashes on the camera when a key is pressed. D. The batteries are correctly placed within the remote. Answer: C Question No : 5 Which two items should you check on the local Cisco TelePresence C Series Codec when audio is not received? (Choose two.) A. The microphone is plugged in. B. The microphone is turned on in the menus. C. The volume on the monitor is turned up. D. The far end is sending audio. Answer: C,D Question No : 6 You are having trouble upgrading the Cisco TelePresence C Series Codec system using the web interface. How else might you attempt the upgrade? A. Use the API command interface. B. Use the HTTP or HTTPS Interface. C. Use the menus and a USB drive. D. Use the remote ISDN connection.
Question No : 7 How many digital video inputs does a Cisco TelePresence Codec C40 have? A. 2 B. 0 C. 1 D. 3 E. 5 Answer: D http://wwwxiscoxom/c/en/us/products/collateral/collaboration-endpoints/telepresence-codec-c40/ data sheet c78-628593.html 2xHDMIand1xDVI-l Question No : 8 What will happen if the local zone on a Cisco TelePresence VCS does not have a search rule? A. Calls to locally registered devices will fail. B. Calls from locally registered devices will fail. C. Calls to externally registered devices will fail. D. Calls from externally registered devices will fail. Answer: A If the alias is found within the Local Zone, in one of the external zones, or a routing destination is returned by the policy service, the VCS attempts to place the call. If the alias is not found, it responds with a message to say that the call has failed. Question No : 9 How can you independently restore the default links on a Cisco TelePresence VCS? A. with an xcommand from the API
B. by performing a factory reset C. from the bandwidth configuration section of the web interface D. by performing a reboot Answer: A xcommand DefaultLinksAdd Question No : 10 What should you use to back up the configuration of a Cisco TelePresence VCS (X5 software or above)? A. the backup and restore tool B. the serial port and the backup command C. the serial port and the xbackup command D. SCP to download the file called "backup.tft" Answer: A The Backup and restore page (Maintenance > Backup and restore) is used to create and restore backup files of your VCS data. Question No : 11 Which troubleshooting tools are available on the Cisco TelePresence VCS (X5 or above)? A. configuration logs for all endpoints registered, endpoint status logs, and Cisco TelePresence MCU conference reports B. system resources, call history, search history, zone and subzone status, warnings, event logs C. H.323, SIP, and ISDN syslogs for each endpoint registered, all logs for all calls on the network D. searches, locate tools, check rules, syslog, call history, current calls, call logs from the endpoints Question No : 12 Where do you find the Clusterwide Domain Configuration? A. System > Enterprise Parameters
B. System > Enterprise Phone Configuration C. Device > Trunk D. User Management > SIP Realm Answer: A Question No : 13 Where do you change the Maximum Session Bit Rate for Video Calls? A. Device > Trunk B. System > Location C. Media Resources > Media Resource Group D. System > Enterprise Parameters E. System > Region Answer: E Question No : 14 How many peers can you configure per neighbor zone? A. 1 B. 2 C. 3 D. 4 E. 5 F. 6 G. 8 H. 12
Answer: E Question No : 15 When trunking a Cisco VCS to Cisco Unified Communications Manager, what value should the H.323 mode be set to? A. On B. Off C. Auto D. Best Effort http://www.cisco.com/c/dam/en/us/td/docs/telepresence/infrastructure/vcs/config_guide/x8-2/cisco-vcs- SIPTrunk-to-Unified-CM-Deployment-Guide-CUCM-8-9-and-X8-2.pdf
Powered by TCPDF (www.tcpdf.org) << Practice Test Demo - 2PassEasy >> THANKS FOR TRYING THE DEMO OF OUR PRODUCT Visit Our Site to Purchase the Full Set of Actual 500-006 Exam Questions With Answers. We Also Provide Practice Exam Software That Simulates Real Exam Environment And Has Many Self-Assessment Features. Order the 500-006 Product From: https://www.2passeasy.com/dumps/500-006/ Money Back Guarantee 500-006 Practice Exam Features: * 500-006 Questions and Answers Updated Frequently * 500-006 Practice Questions Verified by Expert Senior Certified Staff * 500-006 Most Realistic Questions that Guarantee you a Pass on Your FirstTry * 500-006 Practice Test Questions in Multiple Choice Formats and Updatesfor 1 Year