KSR Series Single Rail LCD Console with PS/2 KVM Switch User Manual Rev 1.0
Packing List KSR Series User Manual The complete KSR-115XX / 117XX / 119XX package consist of: One 1U 19 rack mount console Two rails with front and rear bracket Two long brackets. (Needed for rack depth 828 ~ 1000mm) One 1.8M signal cable One power cord One user manual CD One quick installation guide Two key Six flat screws. (for rail mount to console body) Six screws. (for replace long bracket) The complete KSR-12001 package consist of: One 1U 19 rack mount console Two rails with front and rear bracket One 1.8M signal cable Two 1.8M USB cable One 1.8M DVI cable One Audio cable One power cord One user manual CD One quick installation guide Two key Six flat screws. (for rail mount to console body) The complete KSR-12008 / 12016 package consist of: One 1U 19 rack mount console Two rails with front and rear bracket One 1.8M signal cable One power cord One user manual CD One quick installation guide Two key Six flat screws. (for rail mount to console body) I
Check to make sure that the unit was not damaged in shipping. If you encounter a problem, contact your dealer. Please read this manual thoroughly, and follow the installation and operation procedures carefully to prevent any damage to the product, and/or any of the devices that connect to it. Safety Instructions 1. Please read these safety instructions carefully. 2. Please keep this User s Manual for later reference. 3. Please disconnect this equipment from AC outlet before cleaning. Don t use liquid or sprayed detergent for cleaning. Use moisture sheet or clothe for cleaning. 4. For pluggable equipment, the socked-outlet shall be installed near the equipment and shall be easily accessible. 5. Please keep this equipment from humidity. 6. Lay this equipment on a reliable surface when install. A drop or fall could cause injury. 7. Do not leave this equipment in an environment unconditioned, storage temperature above 60 0 C, it may damage the equipment. 8. The opening on the enclosure is for air convection hence the equipment from overheating. DO NOT COVER THE OPENING. 9. Make sure the voltage of the power source connect the equipment to the power outlet. 10. Please keep the power cord such a way that people can not step on it. Do not place anything over power cord. The power cord must rate for the voltage and current marked on the product s electrical ratings label. The voltage and current rating of the cord should be greater than the voltage and the current rating marked on the product. 11. All cautions and warning on the equipment should be noted. 12. If the equipment is not in use for long time, disconnect the equipment from mains to avoid being damaged by transient over-voltage. 13. Never pour any liquid into ventilation openings; this could cause fire or electrical shock. 14. Never open the equipment. For safety reason, qualified service personnel should only open the equipment. 15. If one of the following situations arises, get the equipment checked by service II
personnel. The Power Cord or plug is damaged. Liquid has penetrated into the equipment. The equipment has been exposed to moisture. The equipment has not worked well or you can not get it work according to User s Manual. The equipment has dropped and damaged. If the equipment has obvious signs or breakage. III
Index of Contents KSR Series User Manual Packing List... I Safety Instructions... II Index of Contents... IV 1. General Information... 1 1.1 Overview... 1 1.2 Product Specification... 2 1.2.1 KSR-11501 / 11508 / 11516 Specification... 2 1.2.2 KSR-11701 / 11708 / 11716 Specification... 6 1.2.3 KSR-11901 / 11908 / 11916 Specification... 10 1.2.4 KSR-12001 / 12008 / 12016 Specification... 14 2. Panel Controls and OSD Function... 18 2.1 Auto Tune... 18 2.2 Input Source... 19 2.3 Brightness... 19 2.4 Contrast... 20 2.5 Color... 20 2.6 Position... 21 2.7 Language... 22 2.8 Recall... 23 2.9 Exit... 23 2.10 Power Indicator... 23 3. Installation... 24 3.1 Install KSR-115XX / 117XX / 119XX into Cabinet... 24 3.1.1 Notes... 24 3.1.2 Hardware Kits Contents... 24 3.1.3 Installation Steps... 25 3.1.4 Replace Longer Bracket Steps (For rack depth 828~1000mm) 27 3.1.5 Unload Steps... 27 3.2 Install KSR-120XX Console into Cabinet... 29 3.2.1 Notes... 29 3.2.2 Hardware Kits Contents... 29 3.2.3 Install Console Steps... 30 3.3 Installing the Video Card and Video Driver... 32 3.3.1 Configuring the Display Settings... 32 3.3.2 Connecting the Console... 33 IV
3.4 Turning on the Console... 34 3.5 Testing the Console... 34 4. KVM SWITCH... 36 4.1 Introduction... 36 4.2 Feature... 36 4.3 Technical Specifications... 37 4.4 System Requirements... 38 4.5 Cable Diagrams... 38 4.6 Product Details... 39 4.7 Hardware Installation... 39 4.8 Operation & Usage... 41 4.8.1... 41 4.8.2... 41 4.8.3 OSD Main Screen Headings... 42 V
1. General Information 1.1 Overview KSR Series User Manual The KVM console is an ideal solution for network administration with multiple servers / platforms. Their 15 / 17 / 19 / 20.1-inch large size TFT LCD color display and ultra-low-profile compact industrial keyboard / touchpad provide the user-friendliest and most reliable environment for network administrators. All these functions are integrated in a 19-inch 1U space with rugged construction design to achieve ultra space saving and high reliability for high quality industrial network applications. The KVM console provide superior picture quality and state-of-the-art features mounted in an industrial grade, rack mount console. The console forms a rugged enclosure that protects the panel from industrial hazards and permits easy access to panel controls. The KVM console panels provide flicker-free color images at optimal resolutions. The panels 0.297 x 0.297 mm pixel pitch 15 inch (0.264 x 0.264 mm pixel pitch 17 inch, 0.098 x 0.294 mm pixel pitch 19 inch, 0.255 x 0.255mm pixel pitch 20.1 inch) ensures crisp images with clear definition, even at high resolutions. The KVM console panels are intelligent, microprocessor-based, and have an ergonomically designed display. The KVM console panels employ the latest in active matrix thin film transistor (TFT) technology, providing crisp screen images and wide viewing angles. Unlike CRT panels, LCD panels are inherently immune to the magnetic fields commonly found on the plant floor or communications centers. LCDs are also typically brighter than conventional CRT technology, making them ideal for the high ambient lighting conditions found in many of today's factory environments. On-screen menus allow for display adjustments. In addition, the panels' Plug-n-Play+ features support Windows 95/98,NT and XP, while a universal power supply ensures global applicability. The KVM console panels are compatible with most analog RGB (red, green, blue) display standards, including PS/2, optional for Sun Micro System, Apple Macintosh Centris, Quadra, and Macintosh II family signals. The LCD panel is capable of displaying crisp and vibrant color graphics with VGA, S2GA, XGA (non-interlaced), SXGA, UXGA, and most Macintosh compatible color video cards. 1
1.2 Product Specification 1.2.1 KSR-11501 / 11508 / 11516 Specification KSR Series User Manual Model name KSR-11501 Number of ports 1 Dimension 482 x 447.5 x 44 mm / 19.0 x 17.6 x 1.7 inches Package Dimension 677 x 564 x 206 mm / 26.7 x 22.2 x 8.1 inches Net Weight 11.0 Kg / 24.3 lbs Gross Weight 18.0 Kg / 39.7 lbs Display Size 15 inches Panel Type Active Matrix TFT LCD Resolution Capabilities Maximum Resolution up to 1024 x 768 (XGA) Pixel Pitch Supports 0.297 mm x 0.297 mm Viewing Angle (CR>10) Right-Left View 130 (Typ) Up-Down View 100 (Typ) Contrast Ratio 400:1 Brightness White 250 cd/m² (Center 1 point Typ) Back Light Dual Lamps for Back Light Supported Colors 16M Colors (8-bit with FRC) Response Time Rising Time 5 ms, Decay Time 11 ms Operating System Dos, Windows (3.1, 9x, 2000, NT4, ME, XP, 2003 Server) Linux, Novell 3.12-6, HP UX, SUN Connectors PC Port / Daisy Chain Connectors 1 x VGA HDDB 15-pin 2 x PS/2 Mini Din 6-pin Power Connector 1 x AC Inlet Signal Cable KC-0303 Keyboard Mouse 106 key PS/2 keyboard with touch pad Sync 45 ~ 80 KHz Power Source 100 ~ 240 VAC input Power Consumption 16W, 10.41W for Panel Temperature Operate 0 ~ 50 C / 32 ~ 122 F Storage -20 ~ 60 C / -4 ~ 140 F Humidity 10% ~ 90% RH Chassis Construction Heavy duty steel materials Keyboard Language US, UK, German, French, Spanish, Italian, Portuguese, Dutch, Swiss, Belgium, Swedish, Hebrew, Norwegian, Danish, Japanese, Mandarin, Russian, Arabic Certification CE / FCC, UL / CUL / C-Tick Table 1-1. KSR-11501 Specification 2
Model name KSR-11508 Number of ports 8 Dimension 592 x 447.5 x 44 mm / 23.3 x 17.6 x 1.7 inches Package Dimension 788 x 564 x 206 mm / 31.0 x 22.2 x 8.1 inches Net Weight 12.0 Kg / 26.5 lbs Gross Weight 18.5 Kg / 40.8 lbs Display Size 15 inches Panel Type Active Matrix TFT LCD Resolution Capabilities Maximum Resolution up to 1024 x 768 (XGA) Pixel Pitch Supports 0.297 mm x 0.297 mm Viewing Angle (CR>10) Right-Left View 130 (Typ) Up-Down View 100 (Typ) Contrast Ratio 400:1 Brightness White 250 cd/m² (Center 1 point Typ) Back Light Dual Lamps for Back Light Supported Colors 16M Colors (8-bit with FRC) Response Time Rising Time 5 ms, Decay Time 11 ms Operating System DOS, Win3.x, Win95 / 98 / 98SE / 2000 / ME / XP / Vista, WinNT, Netware, HP Unix, Linux Connectors PC Port Connectors 8 x HDDB 15-pin Daisy Chain Connectors 1 x VGA HDDB 15-pin 2 x PS/2 Mini Din 6-pin Power Connector 1 x AC Inlet Signal Cable KC-1501C Keyboard Mouse 106 key PS/2 keyboard with touch pad Sync 45 ~ 80 KHz Power Source 100 ~ 240 VAC input Power Consumption 16W, 10.41W for Panel Temperature Operate 0 ~ 50 C / 32 ~ 122 F Storage -20 ~ 60 C / -4 ~ 140 F Humidity 10% ~ 90% RH Chassis Construction Heavy duty steel materials Keyboard Language US, UK, German, French, Spanish, Italian, Portuguese, Dutch, Swiss, Belgium, Swedish, Hebrew, Norwegian, Danish, Japanese, Mandarin, Russian, Arabic Table 1-2. KSR-11508 Specification 3
Model name KSR-11516 Number of ports 16 Dimension 592 x 447.5 x 44 mm / 23.3 x 17.6 x 1.7 inches Package Dimension 788 x 564 x 206 mm / 31.0 x 22.2 x 8.1 inches Net Weight 12.5 Kg / 27.6 lbs Gross Weight 19.0 Kg / 41.9 lbs Display Size 15 inches Panel Type Active Matrix TFT LCD Resolution Capabilities Maximum Resolution up to 1024 x 768 (XGA) Pixel Pitch Supports 0.297 mm x 0.297 mm Viewing Angle (CR>10) Right-Left View 130 (Typ) Up-Down View 100 (Typ) Contrast Ratio 400:1 Brightness White 250 cd/m² (Center 1 point Typ) Back Light Dual Lamps for Back Light Supported Colors 16M Colors (8-bit with FRC) Response Time Rising Time 5 ms, Decay Time 11 ms Operating System DOS, Win3.x, Win95 / 98 / 98SE / 2000 / ME / XP / Vista, WinNT, Netware, HP Unix, Linux Connectors PC Port Connectors 16 x HDDB 15-pin Daisy Chain Connectors 1 x VGA HDDB 15-pin 2 x PS/2 Mini Din 6-pin Power Connector 1 x AC Inlet Signal Cable KC-1501C Keyboard Mouse 106 key PS/2 keyboard with touch pad Sync 45 ~ 80 KHz Power Source 100 ~ 240 VAC input Power Consumption 16W, 10.41W for Panel Temperature Operate 0 ~ 50 C / 32 ~122 F Storage -20 ~ 60 C / -4 ~140 F Humidity 10% ~ 90% RH Chassis Construction Heavy duty steel materials Keyboard Language US, UK, German, French, Spanish, Italian, Portuguese, Dutch, Swiss, Belgium, Swedish, Hebrew, Norwegian, Danish, Japanese, Mandarin, Russian, Arabic Table 1-3. KSR-11516 Specification 4
Figure 1-1. KSR-11501 Dimension Figure 1-2. KSR-11508 Dimension Figure 1-3. KSR-11516 Dimension 5
1.2.2 KSR-11701 / 11708 / 11716 Specification KSR Series User Manual Model name KSR-11701 Number of ports 1 Dimension 482 x 447.5 x 44 mm / 19.0 x 17.6 x 1.7 inches Package Dimension 677 x 564 x 206 mm / 26.7 x 22.2 x 8.1 inches Net Weight 12.0 Kg / 26.5 lbs Gross Weight 18.5 Kg / 40.8 lbs Display Size 17 inches Panel Type Active Matrix TFT LCD Resolution Capabilities Maximum Resolution up to 1280 x 1024 (SXGA) Pixel Pitch Supports 0.264 mm x 0.264 mm Viewing Angle (CR>10) Right-Left View 170 (Typ) Up-Down View 160 (Typ) Contrast Ratio 1000:1 Brightness White 250 cd/m² (Center 1 point Typ) Back Light Dual Lamps for Back Light Supported Colors 16.7M Colors (8-bit with FRC) Response Time Rising Time 1.2 ms, Decay Time 3.8 ms Operating System Dos, Windows (3.1, 9x, 2000, NT4, ME, XP, 2003 Server) Linux, Novell 3.12-6, HP UX, SUN Connectors PC Port / Daisy Chain Connectors 1 x VGA HDDB 15-pin 2 x PS/2 Mini Din 6-pin Power Connector 1 x AC Inlet Signal Cable KC-0303 Keyboard Mouse 106 key PS/2 keyboard with touch pad Sync 45 ~ 80 KHz Power Source 100 ~ 240 VAC input Power Consumption 13.35 W for Panel Temperature Operate 0 ~ 50 C / 32 ~ 122 F Storage -20 ~ 60 C / -4 ~ 140 F Humidity 10% ~ 90% RH Chassis Construction Heavy duty steel materials Keyboard Language US, UK, German, French, Spanish, Italian, Portuguese, Dutch, Swiss, Belgium, Swedish, Hebrew,Norwegian, Danish, Japanese, Mandarin, Russian, Arabic Certification CE / FCC, UL / CUL / C-Tick Table 1-4. KSR-11701 Specification 6
Model name KSR-11708 Number of ports 8 Dimension 592 x 447.5 x 44 mm / 23.3 x 17.6 x 1.7 inches Package Dimension 788 x 564 x 206 mm / 31.0 x 22.2 x 8.1 inches Net Weight 13.0 Kg / 28.7 lbs Gross Weight 20.5 Kg / 45.2 lbs Display Size 17 inches Panel Type Active Matrix TFT LCD Resolution Capabilities Maximum Resolution up to 1280 x 1024 (SXGA) Pixel Pitch Supports 0.264 mm x 0.264 mm Viewing Angle (CR>10) Right-Left View 170 (Typ) Up-Down View 160 (Typ) Contrast Ratio 1000:1 Brightness White 250 cd/m² (Center 1 point Typ) Back Light Dual Lamps for Back Light Supported Colors 16.7M Colors (8-bit with FRC) Response Time Rising Time 1.2 ms, Decay Time 3.8 ms Operating System DOS, Win3.x, Win95 / 98 / 98SE / 2000 / ME / XP / Vista, WinNT, Netware, HP Unix, Linux Connectors PC Port Connectors 8 x HDDB 15-pin Daisy Chain Connectors 1 x VGA HDDB 15-pin 2 x PS/2 Mini Din 6-pin Power Connector 1 x AC Inlet Signal Cable KC-1501C Keyboard Mouse 106 key PS/2 keyboard with touch pad Sync 45 ~ 80 KHz Power Source 100 ~ 240 VAC input Power Consumption 13.35 W for Panel Temperature Operate 0 ~ 50 C / 32 ~ 122 F Storage -20 ~ 60 C / -4 ~ 140 F Humidity 10% ~ 90% RH Chassis Construction Heavy duty steel materials Keyboard Language US, UK, German, French, Spanish, Italian, Portuguese, Dutch, Swiss, Belgium, Swedish, Hebrew,Norwegian, Danish, Japanese, Mandarin, Russian, Arabic Table 1-5. KSR-11708 Specification 7
Model name KSR-11716 Number of ports 16 Dimension 592 x 447.5 x 44 mm / 23.3 x 17.6 x 1.7 inches Package Dimension 788 x 564 x 206 mm / 31.0 x 22.2 x 8.1 inches Net Weight 13.5 Kg / 29.8 lbs Gross Weight 21.0 Kg / 46.3 lbs Display Size 17 inches Panel Type Active Matrix TFT LCD Resolution Capabilities Maximum Resolution up to 1280 x 1024 (SXGA) Pixel Pitch Supports 0.264 mm x 0.264 mm Viewing Angle (CR>10) Right-Left View 170 (Typ) Up-Down View 160 (Typ) Contrast Ratio 1000:1 Brightness White 250 cd/m² (Center 1 point Typ) Back Light Dual Lamps for Back Light Supported Colors 16.7M Colors (8-bit with FRC) Response Time Rising Time 1.2 ms, Decay Time 3.8 ms Operating System DOS, Win3.x, Win95 / 98 / 98SE / 2000 / ME / XP / Vista, WinNT, Netware, HP Unix, Linux Connectors PC Port Connectors 16 x HDDB 15-pin Daisy Chain Connectors 1 x VGA HDDB 15-pin 2 x PS/2 Mini Din 6-pin Power Connector 1 x AC Inlet Signal Cable KC-1501C Keyboard Mouse 106 key PS/2 keyboard with touch pad Sync 45 ~ 80 KHz Power Source 100 ~ 240 VAC input Power Consumption 13.35 W for Panel Temperature Operate 0 ~ 50 C / 32 ~ 122 F Storage -20 ~ 60 C / -4 ~ 140 F Humidity 10% ~ 90% RH Chassis Construction Heavy duty steel materials Keyboard Language US, UK, German, French, Spanish, Italian, Portuguese, Dutch, Swiss, Belgium, Swedish, Hebrew, Norwegian, Danish, Japanese, Mandarin, Russian, Arabic Table 1-6. KSR-11716 Specification 8
Figure 1-4. KSR-11701 Dimension Figure 1-5. KSR-11708 Dimension Figure 1-6. KSR-11716 Dimension 9
1.2.3 KSR-11901 / 11908 / 11916 Specification KSR Series User Manual Model name KSR-11901 Number of ports 1 Dimension 532 x 447.5 x 44 mm / 20.9 x 17.6 x 1.7 inches Package Dimension 715 x 564 x 206 mm / 28.1 x 22.2 x 8.1 inches Net Weight 12.5 Kg / 27.6 lbs Gross Weight 19.5 Kg / 43.0 lbs Display Size 19 inches Panel Type Active Matrix TFT LCD Resolution Capabilities Maximum Resolution up to 1280 x 1024 (SXGA) Pixel Pitch Supports 0.098 mm x 0.294 mm Viewing Angle (CR>10) Right-Left View 170 (Typ) Up-Down View 160 (Typ) Contrast Ratio 1000:1 Brightness White 250 cd/m² (Center 1 point Typ) Back Light Dual Lamps for Back Light Supported Colors 16.7M Colors (8-bit with FRC) Response Time Rising Time 1.3 ms, Decay Time 3.7 ms Operating System Dos, Windows (3.1, 9x, 2000, NT4, ME, XP, 2003 Server) Linux, Novell 3.12-6, HP UX, SUN Connectors PC Port / Daisy Chain Connectors 1 x VGA HDDB 15-pin 2 x PS/2 Mini Din 6-pin Power Connector 1 x AC Inlet Signal Cable KC-0303 Keyboard Mouse 106 key PS/2 keyboard with touch pad Sync 45 ~ 80 KHz Power Source 100 ~ 240 VAC input Power Consumption 13.6 W for Panel Temperature Operate 0 ~ 50 C / 32 ~ 122 F Storage -20 ~ 60 C / -4 ~ 140 F Humidity 10% ~ 90% RH Chassis Construction Heavy duty steel materials Keyboard Language US, UK, German, French, Spanish, Italian, Portuguese, Dutch, Swiss, Belgium, Swedish, Hebrew, Norwegian, Danish, Japanese, Mandarin, Russian, Arabic Certification CE / FCC, UL / CUL / C-Tick Table 1-7. KSR-11901 Specification 10
Model name KSR-11908 Number of ports 8 Dimension 642 x 447.5 x 44 mm / 22.4 x 17.6 x 1.7 inches Package Dimension 827 x 564 x 206 mm / 32.6 x 22.2 x 8.1 inches Net Weight 14.0 Kg / 30.9 lbs Gross Weight 21.5 Kg / 47.4 lbs Display Size 19 inches Panel Type Active Matrix TFT LCD Resolution Capabilities Maximum Resolution up to 1280 x 1024 (SXGA) Pixel Pitch Supports 0.098 mm x 0.294 mm Viewing Angle (CR>10) Right-Left View 170 (Typ) Up-Down View 160 (Typ) Contrast Ratio 1000:1 Brightness White 250 cd/m² (Center 1 point Typ) Back Light Dual Lamps for Back Light Supported Colors 16.7M Colors (8-bit with FRC) Response Time Rising Time 1.3 ms, Decay Time 3.7 ms Operating System DOS, Win3.x, Win95 / 98 / 98SE / 2000 / ME / XP / Vista, WinNT, Netware, HP Unix, Linux Connectors PC Port Connectors 8 x HDDB 15-pin Daisy Chain Connectors 1 x VGA HDDB 15-pin 2 x PS/2 Mini Din 6-pin Power Connector 1 x AC Inlet Signal Cable KC-1501C Keyboard Mouse 106 key PS/2 keyboard with touch pad Sync 45 ~ 80 KHz Power Source 100 ~ 240 VAC input Power Consumption 13.6 W for Panel Temperature Operate 0 ~ 50 C / 32 ~ 122 F Storage -20 ~ 60 C / -4 ~ 140 F Humidity 10% ~ 90% RH Chassis Construction Heavy duty steel materials Keyboard Language US, UK, German, French, Spanish, Italian, Portuguese, Dutch, Swiss, Belgium, Swedish, Hebrew, Norwegian, Danish, Japanese, Mandarin, Russian, Arabic Table 1-8. KSR-11908 Specification 11
Model name KSR-11916 Number of ports 16 Dimension 642 x 447.5 x 44 mm / 22.4 x 17.6 x 1.7 inches Package Dimension 827 x 564 x 206 mm / 32.6 x 22.2 x 8.1 inches Net Weight 14.5 Kg / 32.0 lbs Gross Weight 22.0 Kg / 48.5 lbs Display Size 19 inches Panel Type Active Matrix TFT LCD Resolution Capabilities Maximum Resolution up to 1280 x 1024 (SXGA) Pixel Pitch Supports 0.098 mm x 0.294 mm Viewing Angle (CR>10) Right-Left View 170 (Typ) Up-Down View 160 (Typ) Contrast Ratio 1000:1 Brightness White 250 cd/m² (Center 1 point Typ) Back Light Dual Lamps for Back Light Supported Colors 16.7M Colors (8-bit with FRC) Response Time Rising Time 1.3 ms, Decay Time 3.7 ms Operating System DOS, Win3.x, Win95 / 98 / 98SE / 2000 / ME / XP / Vista, WinNT, Netware, HP Unix, Linux Connectors PC Port Connectors 16 x HDDB 15-pin Daisy Chain Connectors 1 x VGA HDDB 15-pin 2 x PS/2 Mini Din 6-pin Power Connector 1 x AC Inlet Signal Cable KC-1501C Keyboard Mouse 106 key PS/2 keyboard with touch pad Sync 45 ~ 80 KHz Power Source 100 ~ 240 VAC input Power Consumption 13.6 W for Panel Temperature Operate 0 ~ 50 C / 32 ~ 122 F Storage -20 ~ 60 C / -4 ~ 140 F Humidity 10% ~ 90% RH Chassis Construction Heavy duty steel materials Keyboard Language US, UK, German, French, Spanish, Italian, Portuguese, Dutch, Swiss, Belgium, Swedish, Hebrew, Norwegian, Danish, Japanese, Mandarin, Russian, Arabic Table 1-9. KSR-11916 Specification 12
Figure 1-7. KSR-11901 Dimension Figure 1-8. KSR-11908 Dimension Figure 1-9. KSR-11916 Dimension 13
1.2.4 KSR-12001 / 12008 / 12016 Specification KSR Series User Manual Model name KSR-12001 Number of ports 1 Dimension 527.2 x 436.4 x 43.8 mm / 20.8 x 17.2 x 1.7 inches Package Dimension 827 x 564 x 206 mm / 32.6 x 22.2 x 8.1 inches Net Weight 16.5 Kg / 36.4 lbs Gross Weight 22.5 Kg / 49.6 lbs Display Size 20.1 inches Panel Type Active Matrix TFT LCD Resolution Capabilities Maximum Resolution up to 1600 x 1200 (UXGA) Pixel Pitch Supports 0.255 mm x 0.255 mm Active Display Area Horizontal: 408.0 mm, Vertical: 306.0 mm Viewing Angle (CR>10) Right-Left view 178 (Typ), Up-Down View 178 (Typ) Contrast Ratio 700 : 1 Brightness White 300 cd/m² Back Light Six Lamps for Back Light Supported Colors 16.7M Colors (8-bit with FRC) Response Time Rising Time 7 ms, Decay Time 9 ms Operating System Dos, Windows (3.1, 9x, 2000, NT4, ME, XP, 2003 Server) Linux, Novell 3.12-6, HP UX, SUN Connectors PC Port 1 x VGA HDDB 15-pin 2 x PS/2 Mini Din 6-pin 2 x USB 1 x DVI, 1 x Audio line in (optional) Power Connector 1 x DC jack Signal Cable KC-0303 Keyboard Mouse 106 key PS/2 keyboard with touch pad Sync 45 ~ 80 KHz Power Source 100 ~ 240 VAC input Power Consumption 35W Temperature Operate 0 ~ 50 C / 32 ~ 122 F, Storage -20 ~ 60 C / -4 ~ 140 F Humidity 10% ~ 90% RH Chassis Construction Heavy duty steel materials Keyboard Language US, UK, German, French, Spanish, Italian, Portuguese, Dutch, Swiss, Belgium, Swedish, Hebrew, Norwegian, Danish, Japanese, Mandarin, Russian, Arabic Table 1-10. KSR-12001 Specification 14
Model name KSR-12008 Number of ports 8 Dimension 527.2 x 436.4 x 43.8 mm / 20.8 x 17.2 x 1.7 inches Package Dimension 827 x 564 x 206 mm / 32.6 x 22.2 x 8.1 inches Net Weight 18.0 Kg / 39.7 lbs Gross Weight 23.5 Kg / 51.8 lbs Display Size 20.1 inches Panel Type Active Matrix TFT LCD Resolution Capabilities Maximum Resolution up to 1600 x 1200 (UXGA) Pixel Pitch Supports 0.255 mm x 0.255 mm Active Display Area Horizontal: 408.0 mm, Vertical: 306.0 mm Viewing Angle (CR>10) Right-Left view 178 (Typ) Up-Down View 178 (Typ) Contrast Ratio 700 : 1 Brightness White 300 cd/m² Back Light Six Lamps for Back Light Supported Colors 16.7M Colors (8-bit with FRC) Response Time Rising Time 7 ms, Decay Time 9 ms Operating System DOS, Win3.x, Win95 / 98 / 98SE / 2000 / ME / XP / Vista, WinNT, Netware, HP Unix, Linux Connectors PC Port Connectors 8 x HDDB 15-pin Daisy Chain Connectors 1 x VGA HDDB 15-pin 2 x PS/2 Mini Din 6-pin Power Connector 1 x AC Inlet Signal Cable KC-1501C Keyboard Mouse 106 key PS/2 keyboard with touch pad Sync 45 ~ 80 KHz Power Source 100 ~ 240 VAC input Power Consumption 35W Temperature Operate 0 ~ 50 C / 32 ~ 122 F Storage -20 ~ 60 C / -4 ~ 140 F Humidity 10% ~ 90% RH Chassis Construction Heavy duty steel materials Keyboard Language US, UK, German, French, Spanish, Italian, Portuguese, Dutch, Swiss, Belgium, Swedish, Hebrew, Norwegian, Danish, Japanese, Mandarin, Russian, Arabic Table 1-11. KSR-12008 Specification 15
Model name KSR-12016 Number of ports 16 Dimension 527.2 x 436.4 x 43.8 mm / 20.8 x 17.2 x 1.7 inches Package Dimension 827 x 564 x 206 mm / 32.6 x 22.2 x 8.1 inches Net Weight 18.5 Kg / 40.8 lbs Gross Weight 24.0 Kg / 52.9 lbs Display Size 20.1 inches Panel Type Active Matrix TFT LCD Resolution Capabilities Maximum Resolution up to 1600 x 1200 (UXGA) Pixel Pitch Supports 0.255 mm x 0.255 mm Active Display Area Horizontal: 408.0 mm, Vertical: 306.0 mm Viewing Angle (CR>10) Right-Left view 178 (Typ) Up-Down View 178 (Typ) Contrast Ratio 700 : 1 Brightness White 300 cd/m² Back Light Six Lamps for Back Light Supported Colors 16.7M Colors (8-bit with FRC) Response Time Rising Time 7 ms, Decay Time 9 ms Operating System DOS, Win3.x, Win95 / 98 / 98SE / 2000 / ME / XP / Vista, WinNT, Netware, HP Unix, Linux Connectors PC Port Connectors 16 x HDDB 15-pin Daisy Chain Connectors 1 x VGA HDDB 15-pin 2 x PS/2 Mini Din 6-pin Power Connector 1 x AC Inlet Signal Cable KC-1501C Keyboard Mouse 106 key PS/2 keyboard with touch pad Sync 45 ~ 80 KHz Power Source 100 ~ 240 VAC input Power Consumption 35W Temperature Operate 0 ~ 50 C / 32 ~ 122 F Storage -20 ~ 60 C / -4 ~ 140 F Humidity 10% ~ 90% RH Chassis Construction Heavy duty steel materials Keyboard Language US, UK, German, French, Spanish, Italian, Portuguese, Dutch, Swiss, Belgium, Swedish, Hebrew, Norwegian, Danish, Japanese, Mandarin, Russian, Arabic Table 1-12. KSR-12016 Specification 16
Figure 1-10. KSR-12001 Dimension Figure 1-11. KSR-12008 Dimension Figure 1-12. KSR-12016 Dimension 17
2. Panel Controls and OSD Function KSR Series User Manual Controls Auto Menu Description Soft power on/off button. Adjacent LED is lit when on. Auto-synchronize and scale down display to any valid factory preset timings. Press to scroll the function you want to adjust. Press to scroll the function you want to adjust. To access the main menu. This button also acts as the Enter button. Table 2-1. Panel Controls Figure 2-1. KSR-115XX / 117XX OSD Control Bar Figure 2-2. KSR-119XX / 120XX OSD Control Bar 2.1 Auto Tune Press the auto tune button. The panel will adjust the display size automatically and also tune the panel to its best condition. 18
2.2 Input Source 1. Press the menu button. 2. Use the Down and Up button to scroll. Auto tune. Input Source Brightness Contrast Color Position Language Recall Exit 3. Press the menu button to enter,and you will see: VGA / DVI 4. Use the Down and Up button to select the input source of signal. 5. Press the menu button to enter 2.3 Brightness 1. Press the menu button. 2. Use the Down and Up button to scroll. Auto tune. Input Source Brightness Contrast Color Position Language Recall Exit 3. Press the menu button to enter. 4. Use the Down and Up button to adjust the brightness of the display. 5. Press the menu button to enter. 19
2.4 Contrast KSR Series User Manual 1. Press the menu button. 2. Use the Down and Up button to scroll. Auto tune. Input Source Brightness Contrast Color Position Language Recall Exit 1. Press the menu button to enter. 2. Use the Down and Up button to adjust the contrast of the display. 3. Press the menu button to enter. 2.5 Color 1. Press the menu button. 2. Use the Down and Up button to scroll. Auto tune. Input Source Brightness Contrast Color Position Language Recall Exit 20
3. Press the menu button to enter. And you will see: Icon Description 9300 K To set CIE coordinates at 9300 K color 7500 K To set CIE coordinates at 7500 K color 6500 K To set CIE coordinates at 6500 K color User To set user defined CIE Auto color To auto adjust color Return To exit and return to the previous page Table 2-2. Icon Description 4. Use the Down and Up button to adjust the color of the display. 5. Press menu to enter. 2.6 Position 1. Press the menu button. 2. Use the Down and Up button to scroll. Auto tune. Input Source Brightness Contrast Color Position Language Recall Exit 3. Press the menu button to enter. And you will see: Icon Image Pos OSD Pos Return Description To adjust the position of the image. To adjust the position of the OSD. To exit and return to the previous page Table 2-3. Icon Description 21
4. Use the Down and Up button to scroll. 5. Press the menu button to enter. KSR Series User Manual 2.7 Language 1. Press the menu button. 2. Use the Down and Up button to scroll. Auto tune. Input Source Brightness Contrast Color Position Language Recall Exit 3. Press the menu button to enter. And you will see: English German French Italian Spanish 4. Use the Down and Up button to scroll. 5. Press the menu button to enter. 22
2.8 Recall KSR Series User Manual 1. Press the menu button. 2. Use the Down and Up button to scroll. Auto tune. Input Source Brightness Contrast Color Position Language Recall Exit 3. Press the menu button to enter, and you will see: Yes/ No 4. Select Yes button then Menu button to recall the factory setting. Select No to return to the previous page. 2.9 Exit Press the exit button to quit OSD menu. 2.10 Power Indicator GREEN RED RED RED ON STANDBY SUSPEND OFF OSD On Screen Display 23
3. Installation 3.1 Install KSR-115XX / 117XX / 119XX into Cabinet 3.1.1 Notes KSR Series User Manual 1. Please check all peripherals according the list before installation. To make sure that the whole unit was not damaged and lost during shipping process. If you encounter any problem, please contact your dealer. 2. Before installation, make sure all peripherals and computer have been turned off. 3. The cabinet depth range must be in 504 ~ 1000 mm for KSR-11501 / 11701 (554 ~1000 mm for KSR-11901). And the depth range must be 614 ~ 1000 mm for KSR-11508 / 11516 / 11708 / 11716 (664 ~1000 mm for KSR-11908 / 11916). Contact your dealer for deeper cabinet application. 4. Reliable grounding of rack-mounted equipment should be maintained. Particular attention should be given to supply connections other than direct connections to the branch circuit. 3.1.2 Hardware Kits Contents 1. Rail with front and rear bracket x 2. (Please identify the brackets. Right and left sides are different. For rack depth 504 ~ 828 mm) 2. Long bracket x 2. (Needed for rack depth 828 ~ 1000mm) 3. Flat screw x 6 (for rail mount to console body) 4. Screw x 6 24
5. Key x 2 KSR Series User Manual 3.1.3 Installation Steps 1. Loose (Not release) four rear screws then adjust rear bracket to fit your cabinet. 2. Install front and rear bracket on cabinet. 3. Tight-up four rear screws. 4. Repeat step 1~3 for the other side. 5. Push console into left and right rails. (Be careful when take out console.) 25
6. Unlock and pull rail lock switch (left and right at the same time) then push console to the end. lock unlock 7. Install three screws in rear of the console. (Both sides) rail-lock switch 8. Finish installation as below. 26
3.1.4 Replace Longer Bracket Steps (For rack depth 828~1000mm) 1. Release six screws. 2. Take rear bracket out. Original bracket 2 Input rear long bracket to rear of the rail then adjust rear bracket to fit your cabinet. Tight-up 2~3 screws upon the length you need. One is forbidden. Rear long bracket 4. Repeat step 1~3 for the other side. 5. Repeat 3.1.3 step to install console. 3.1.5 Unload Steps 1. Make sure the console is lock. 2. Release three screws in rear of the console. (Both sides) 27
3. Unlock. KSR Series User Manual 4. Pull console out until console lock. 5. Pull rail-release switch and pull console out.(both sides. Be careful when pull out console.) rail-release switch 6. Push rail-lock switch on the rail and push rail back.(both sides) rail-lock switch on the rail 28
3.2 Install KSR-120XX Console into Cabinet 3.2.1 Notes KSR Series User Manual 1. Please check all peripherals according the list before installation. To make sure that the whole unit was not damaged and lost during shipping process. If you encounter any problem, please contact your dealer. 2. Before installation, make sure all peripherals and computer have been turned off. 3. The cabinet depth range must be in 666 ~ 962 mm KSR-12001 (671 ~ 965 mm KSR-12008 / 12016). Contact your dealer for deeper cabinet application. 4. Reliable grounding of rack-mounted equipment should be maintained. Particular attention should be given to supply connections other than direct connections to the branch circuit. 3.2.2 Hardware Kits Contents 1. Rail with front and rear bracket x 2 2. Screw (length = 6 mm) x 6 3. Key x 2 29
3.2.3 Install Console Steps KSR Series User Manual 1. Adjust rail until two screws appear. Loose (Not release) two rear screws then adjust rear bracket to fit your cabinet. Rail 2. Install front and rear bracket on cabinet. 3. Tight-up two rear screws. 4. Repeat step 1~3 for the other side. 5. Pull rail until it lock and keep the part A in front of the rail (Both sides).then push console into left and right rails. (Be careful rear box loose when take out console from carton.) 30
Part A 6. Pull rail release switch (left and right at the same time) then push console to the end. Rail-release switch 7. Install three screws in rear of the console (Both sides). 8. Finish installation as below. 31
3.3 Installing the Video Card and Video Driver KSR Series User Manual Before connecting the LCD console, make sure your computer has a video card already installed for the panel. After you connect the console, install the video software driver. The video driver is supplied by the video card manufacturer and may be found on the CD-ROM that came with your computer. If you need information on installing a video card or video driver, refer to the manual that came with your video card. 3.3.1 Configuring the Display Settings After connecting the console and turning on your computer, you may need to configure one or more of the following display settings: Display mode (also called desktop area or video resolution) Refresh rate (also called vertical scan rate or vertical sync) Color depth (also called color palette or number of colors) Each video card has several controls that let you adjust the display settings. However, the software and driver for each video card is unique. In most cases, you adjust these settings by using a program or utility provided by the manufacturer of the video card. Most video cards use the Windows Display Properties control panel to configure the display. To open the Windows Display Properties, click the right mouse button in a blank area of the Windows desktop and then select Properties. The Settings tab usually lets you change the Color Palette and the Desktop Area (x by y pixel resolution). Some video cards integrate additional features into the Windows Display Properties control panel to give you an exceptional setup that is flexible and easy to use. For example, the control panel may include an Advanced Properties button, an Adjustment tab, or a Refresh tab for changing other settings. Other video cards have a separate utility for setting display properties. Whenever you change the resolution, color, or refresh rate, the image size, position, or shape may change. This behavior is normal. You can readjust the image using the panel on-screen controls. For more information on the panel on-screen controls, refer to Chapter 2. For more information on configuring the display settings, refer to the manual that came with your video card. 32
3.3.2 Connecting the Console KSR Series User Manual 15 / 17 / 19 - inch LCD console: To connect an LCD console to a computer, perform the following steps Figure 3-1. The Rear View of Single Port LCD Console 1. Turn off your computer. You should always turn off your computer before connecting or disconnecting a device. 2. Connect the video (VGA) connector of the KVM cable to the video card connector on the rear panel of your computer. 3. Identify and connect the PS/2 mouse and PS/2 keyboard connector to the correct PS/2 ports on the rear panel of your computer. 4. Connect the AC power cord to the power inlet on the console and then to a power outlet. 20.1 LCD console: To connect an LCD console to a computer, perform the following steps Figure 3-2. The Rear View of Single Port LCD Console 1. VGA port 2. PS/2 keyboard 3. PS/2 mouse 4. PS/2-USB select 5. USB 2.0 port 6. Audio line in (optional) 7. USB 2.0 port (front USB) 8. DVI port 9. AC Inlet 33
1. Turn off your computer. You should always turn off your computer before connecting or disconnecting a device. 2. Connect the video (VGA) connector of the KVM cable to the video card connector on the rear panel of your computer. 3. Identify and connect the PS/2 mouse and PS/2 keyboard connector to the correct PS/2 ports on the rear panel of your computer. Or you can use USB interface to connect your computer. (Use PS/2-USB switch to select your interface. The switch has to be on PS/2 side when you use PS/2 interface connector.) Please don't plug PS/2 and USB cables at the same time 4. Connect the AC power cord to the power inlet on the console and then to a power outlet. 3.4 Turning on the Console Make sure all cables and the power cord are connected properly. Be sure to tighten all connector screws. Grab the front handle. Pull the console all the way out then lift the panel up. This will disengage the momentary on/off switch and the unit should power on. The LED on the left or underneath of the panel will be green light. 3.5 Testing the Console To test that the console is working properly, perform the following steps: 1. Power up the console, and then turn on your computer. 2. Make sure the video image is centered within the screen area. Use the OSD controls to adjust the image (see note below) or press the Auto button on the left or underneath of the panel. If the unit does not power on when the panel is pulled up, try to push the power on/off button underneath or on the left of the LCD panel to power up the unit. 34
You can adjust the horizontal and vertical position, contrast, and brightness to better suit your video card and your personal preference. Refer to Chapter 2 for more information on using the on-screen menu to adjust the video display Before you begin, make sure that powers to all the devices you will be connecting up have been turned off. To prevent damage to your installation due to ground potential difference, make sure that all the devices on the installation are properly grounded. Consult your direct vendor for any technical issues if necessary. 35
4. KVM SWITCH 4.1 Introduction KSR Series User Manual This PS2 KVM (Keyboard, Video and Mouse) Switch allows multiple computers (PCs or servers) controlled by one set of keyboard, monitor and mouse. It ensures easy switch by front panel button, Hot-keys or the friendly On Screen Display (OSD) menu with connection up to 128 computers (by chaining 16-port PS2 KVMs). Not only naming for each computer can be done for easy identification, it also protects access by passwords. Additionally with the Auto Scan function it helps you managing all connecting systems at ease. 4.2 Feature Software free, easy installation, fully plug-and-play design. Compatible with typical PS/2 computers, monitors and keyboards. Supports IntelliMouse, IntelliMouse Explorer, and Logitech Net Mouse etc. Compatible using DOS, Win3.x, Win95 / 98 / 98SE / 2000 / ME / XP / Vista, WinNT, Netware, HP Unix, Linux etc. Supports Hot plug-and-play (if computer and operation system also supports this feature) Supports high resolution video at 1024 x 768 KSR-115 series (1280 x 1024 KSR-117 / 119 series, 1600 x 1200 KSR-120 series), with DDC2 monitor compatibility. Auto Scan function scans for all connecting computer at intervals between 5~255 seconds. Use power adaptor to provide electricity. Front panel channel selection button and indication lights. By daisy-chaining it can connect up to 64 computers (for all 8-port PS2 KVM connection) or 128 computers (for all 16-port PS2 KVM connection) Separate naming for each computer for easy identification. Provide password protection and operation level restriction. 19 rack mount kit for easy rack installation Exclusive port for daisy-chain connection Firmware upgrade facility through RS-232 interface Dual power input- When primary power connection fails, secondary power automatically initiates to prevent unwanted device shutdown. 36
4.3 Technical Specifications KSR Series User Manual Model No. KSR-11508 / 11708 / 11908 / 12008 KSR-11516 / 11716 / 11916 / 12016 PC Port 8 16 PC Port Connector (All Female Types) HDDB 15-pin Daisy Chain Port Connector 1 x VGA HDDB 15-pin and 2 x Mini Din 6-pin (All Female Types) special cable On Screen Display Control Yes Scan Intervals 5~255 Sec. Keyboard Emulation PS/2 Mouse Emulation PS/2 VGA Resolution 1024 x 768 KSR-11508 / 11516, 1280 x 1024 KSR-11708 / 11716 / 11908 / 11916, 1600 x 1200 KSR-12008 / 12016 Bandwidth 200MHz Daisy Chain MAX Level 8 levels Table 4-1. Technical Specification 37
4.4 System Requirements Model No. KSR-11508 / 11708 / 11908 / 12008 Computer side 8 x HDDB 15-pin male to one HDDB 15-pin male with two Mini Din 6-pin male special cable Table 4-2. System Requirements Model No. KSR-11516 / 11716 / 11916 / 12016 Computer side 16 x HDDB 15-pin male to one HDDB 15-pin male with two Mini Din 6-pin male special cable Table 4-3. System Requirements 4.5 Cable Diagrams PC Port Special Cable: HDDB 15-pin male to one HDDB 15-pin male (VGA) with two Mini Din 6-pin male (PS/2) special cable Figure 4-1. HDDB 15-pin / VGA + PS/2 x 1 (1.8M) Daisy Chain Cable (VGA with PS/2 Cable): One HDDB 15-pin male (VGA) with two Mini Din 6-pin male (PS/2) to one HDDB 15-pin male (VGA) with two Mini Din 6-pin male (PS/2) Figure 4-2. Daisy Chain Cable 38
4.6 Product Details KSR Series User Manual Rear panel of KSR-11508 / 11708 / 11908 / 12008: Rear panel of KSR-11516 / 11716 / 11916 / 12016: Figure 4-3. Rear Panel 4.7 Hardware Installation Before installation, please make sure all of peripherals and computers have been turned off. This example of installation is based on 8 port console and you also can think that 16 port console have the same installation procedures Step 1 Each PC port connector is HDDB 15-pin type. Locate your input cable. It will have a HDDB 15-pin male connector at one end. Plug it into any label computer port on the rear of console unit. The other end of input cable will have three connector; a HDDB 15-pin male type for PC video, a Mini Din 6-pin male type for keyboard and Mini Din 6-pin male type for mouse. To plug these three connectors into the respective ports of computer. Repeat the same procedure to all of PCs. Figure 4-4. Hardware Installation 39
Step 2 Double-check all of the connections. You can check the color of keyboard and mouse connector to make sure the keyboard and mouse cables connect to the correct ports. Step 3 Attach the power cord to the console unit and plug the other end into an electrical receptacle. Switch on your monitor. You can see the power LED on, and you can hear a beep. Step 4 Daisy Chain If daisy chaining is needed please use the daisy chain cable included with package. Please do not use other type of cable for daisy chaining PS2 KVMs. Figure 4-5. Daisy Chain 40
4.8 Operation & Usage KSR Series User Manual 4.8.1 At factory default the PS2 KVM will not ask for password unless it is set by user. You may press Scroll Lock twice followed by F2 to bring up password setting menu. Before you are familiarized with this device, it is strongly recommended to use without password. If password is forgotten, please send PS2 KVM to your distributor for factory reset. 4.8.2 To switch port, you may enter OSD menu to select port, or, use Hot-Key to perform switching. To bring up OSD menu, please press Scroll Lock twice to activate OSD Main Menu as illustrated below (Figure4-6). Figure 4-6. OSD Main Menu 41
4.8.3 OSD Main Screen Headings KSR Series User Manual indicates the computer is powered on at selected port indicates the computer attached at this port has password protected. All ports at factory default do not have password assigned, therefore no icon present USER1~8 Port name of corresponding port number. USER 1~8 illustrated as factory default setting. indicates the PC port is set for Auto Scan Mode. At factory default all PC port is active for Auto Scan. S Every time switching is made PS2 KVM beeps for notification. Please press Scroll Lock twice followed by S to turn beeper on or off _ to select 1~8 computer Ports (1~8 PC Port) + to select A~H computer port (9~16 PC Port) R to set factory default. Password will not be erased after this operation Select computer at previous port Select computer at next port PgUp Select previous bank PgDn Select next bank 1 1 Left hand side 1 indicates current active port, right hand side 1 indicates current active bank. F1 Edit computer name F2 Password setting F3 Select scan port F4 Auto scan mode F5 Hot key setting ESC Exit OSD SCAN Scan rate RATE VERSION Firmware version 42
Use right hand side of OSD commands for adjust settings Function keys: F1, F2, F3, F4, F5, ESC and left arrow key First row on right hand window - 1,1,Bank1 : indicates currently PS2 KVM active at Bank 1, computer port 1. SCAN RATE set at 10 second Firmware version now at version 1.0 F1 Edit computer name (EDIT) On the OSD menu, please press F1 to edit PC port name as illustrated below (Figure4-7) Now please use the secondary function key to F1(SAVE), F2(ERASE), or ESC(QUIT) Edit the desirable name at cursor position, maximum 12 characters. F1- Save port name settings and brings back to OSD main menu F2- Erase all texts. To erase individual character, please use Backspace ( ) ESC to exit EDIT menu Figure 4-7. Edit PC Port Name Menu 43
F2- Password setting (SECURITY) Press F2 at OSD main menu to activate password setting ( SECURITY). Password setting menu for PORT USER pops up as illustrated below (Figure4-8). In this screen you may use the secondary OSD function keys: F1(SUPERUSER), ESC(QUIT), ENTER(Complete). F1- To set password please press F1(SUPERUSER) to set SUPERUSER password (Figure4-10). No password for SUPERUSER is set at factory default. Please enter password of maximum 8 characters. To remove SUPERUSER password, press ENTER at New Password field. ENTER- Press ENTER to complete settings ESC- When setting is finished, press ESC return to OSD main menu. Figure 4-8. Set PC Port Password Figure 4-9. Retype Your Password For Verification (CONFIRM) 44
Figure 4-10. Set Super User Password 45
PC port without Password illustrated below (Figure4-11): Figure 4-11. PC port without Password At factory default, no password is set for PS2 KVM Switch as illustrated above. Selected PC port is powered on with indication. To setup password please open OSD, select SECURITY. Please refer to (Figure4-8) and (Figure4-9). PC port with password illustrated below (Figure4-12): Figure 4-12. PC port with Password Password request OSD appears for Port-1 computer with powered on status. Enter password directly. Password allowable length at 1 to 8 characters only (8 characters max). Press ENTER after password input to commence operation for this PC. SUPERUSER PASSWORD illustrated below (Figure4-13): Figure 4-13. SUPERUSER PASSWORD If SUPERUSER password is set, PS2 KVM Switch will ask for password when KVM is powered on or at RESET. Please enter password follow by ENTER key to continue operation. F3- SELECT SCAN PORT Press F3 at OSD main menu to select Auto Scan active port. If a port is selected for Auto Scan, a icon appears, press F3 again, the icon will disappear. 46
F4- AUTO SCAN Press F4 at OSD main menu to enter Auto Scan function menu as illustrated below (Figure4-14). The secondary function keys are F1, F2 and F3 F1- To start complete scanning, please press F1 (BROADCAST). All ports will be scanned regardless whether the port is connected with active computer. The scanning process will be stopped when ESC is pressed. As scan terminates, KVM switch maintains at last scanned PC port OSD. F2- To start scanning powered on PC only, please press F2 (POWERED ON PC). To stop scanning, please press ESC button. As scan terminates, KVM switch maintains at last scanned PC port OSD. F3- To scan selected PC, please press F3 (SCAN SELECT PC) to commence scanning. To stop scanning, please press ESC button. As scan terminates, KVM switch maintains at last scanned PC port OSD. ESC- Press ESC to Exit the Auto Scan menu. Figure 4-14. AUTO SCAN F5- HOT-KEY At OSD main menu, please press F5 to enter HOT-KEY setting menu (Figure4-15). In the HOT KEY setting menu, secondary selection keys are F1, F2, F3, ENTER. Press F1 to select Scroll Lock as Hot-key Press F2 to select Num Lock as Hot-key Press F3 to select Caps Lock as Hot-key Press ENTER to save setting and exit the Hot-key setting menu 47
Figure 4-15. HOT KEY OSD RATE / SCAN RATE SETTING To set scan rate please press button to enter Scan Rate/OSD Rate setting menu as illustrated below (Figure4-16). The secondary menu functions are F1 and ENTER button SCAN RATE SETTING Please note that scan rate is set 10 seconds at factory default. Please enter desirable time interval (5~255 seconds) in the cursor and press ENTER to confirm setting. OSD RATE SETTING Press F1 to enter OSD TIME setting screen (Figure4-17). Please enter OSD RATE at bottom right corner (005~255 seconds). Press ENTER to complete setting (005~255 seconds) and returns to OSD main menu. Please press ESC to clear OSD display if OSD Time is not set. When OSD Time is set, please wait until setting time terminates. Note that ESC button OSD cancellation cannot be used when OSD Time is set. When entering OSD RATE and SCAN RATE please enter complete three digits. For example, to enter 5 seconds, please input 005; to enter 10 seconds, please input 010. 48
Figure 4-16. Main OSD Scan Rate Setting Menu Figure 4-17. OSD time setting menu 49