WIRELESS FIRST RESPONDER/ RANGE HAILER OPERATING MANUAL

TABLE OF CONTENTS: TOPIC Equipment Features & Benefits Standard Components & Accessories Loudspeaker, Wireless Transmitter Pack & Microphone Specifications Loudspeaker Battery Charging Transmitter Pack Battery Installation General Operating Safety Guidelines Introduction to Remote/Wireless Operations Remote/Wireless Operations Remote/Wireless Operations Connecting to an External Audio Source Remote/Wireless Operations Connecting to a DVR & Microphone Local/Wired Operations Battery Charging, Maintenance & Storage PAGE #(s) 1 2 3 4 4 5 5 6 6 7 8 9 10

EQUIPMENT FEATURES & BENEFITS: Wireless First Responder Loudspeaker Unit with 2 channel VHF Integrated/Internal Wireless Receiver & Transmitter Pack The Wireless First Responder (WFR) is a tool designed to help to ensure that your agency s message is heard loud and clear in virtually any general public address or high risk application. HOSTAGE/CRISIS NEGOTIATIONS: Allows Crisis Negotiator to initiate immediate communications with a subject or multiple subjects involved in a standoff situation. Unlike a bullhorn which discloses the location of the operator, the WFR Loudspeaker unit's remote/wireless function allows for communication while staying out of harms way and under proper cover. TACTICAL RESPONSE: Allows Tactical staff to broadcast their commands, instructions, or surrender ritual loudly and clearly to an individual subject or a large group of unruly individuals. Unlike a bullhorn which requires the operator to hold the device, the WFR allows for hands free operations allowing for immediate weapon access. EMERGENCY MANAGEMENT: Allows First Responders to give instructions to the public from safe distances to help ensure minimal exposure to potentially contaminated individuals and direct victims of a natural disaster to relief stations. Remote/Wireless Operations Delivered with a Transmitter Pack that wirelessly transmits audio data to the WFR Loudspeaker unit s internal/integrated VHF Receiver to distances of 150 to 200 ft. Remote/Wireless Volume Control Delivered with Remote Volume Control Dial that connects to Transmitter Pack to allow operator to increase/decrease the WFR Loudspeaker unit s volume level remotely during remote/wireless operations. Expandable/Scalable The VHF Transmitter Pack can wirelessly transmit audio data to up to (3) WFR Loudspeaker units simultaneously to broadcast audio over a larger area (see Wireless First Responder Range Hailer Configuration). Local/Wired Operations WFR Loudspeaker unit is equipped with MIC IN and LINE IN ports to allow the unit to broadcast audio when connected directly to a microphone or other external audio device source (CD player, MP3 player, Digital Voice Recorder, etc ). Compact & Portable WFR Loudspeaker unit dimensions are 8.5 X 7.1 X 11.2 and weighs less than 9 lbs with battery. Rechargeable Battery Powered When fully charged WFR Loudspeaker unit can be powered from its internal rechargeable battery for ~ 8 hours (an UNLIMITED operating time can be achieved when unit is connected to an external power supply). Remote/Local Audio Broadcast & Recording Capability Delivered with an external Digital Voice Recorder and appropriate cables/adapters to allow for local/remote broadcast of pre recorded audio messages/commands or the ability to record audio broadcast through the WFR Loudspeaker unit for review/documentation purposes. Custom Padded Deployment Case Helps protect the WFR Loudspeaker unit when being operated in inclement weather conditions. 1.

STANDARD COMPONENTS & ACCESSORIES: Wireless First Responder Item #: ETG WFR SYS (1) Loudspeaker Unit with Integrated/ Internal 2 channel VHF Wireless Receiver (1) 12v Rechargeable Battery (1) AC Power Adapter/Charger (1) Handheld Microphone (1) 2 Channel VHF Wireless Transmitter Pack with 9v Alkaline Battery (non rechargeable) (1) Remote Volume Control Dial with Stereo Splitter Cable (1) Lapel Microphone (1) Headset Microphone (1) Digital Voice Recorder Kit, includes: (1) Digital Voice Recorder (1) USB 2.0 Data Transfer Cable (1) 3.5mm (1/8") Stereo Patch Cable (2) AA Alkaline Batteries (non rechargeable) (1) Custom Padded Loudspeaker Deployment Case Wireless First Responder Range Hailer Configuration Item #: ETG WFR RH (3) Loudspeaker Unit with Integrated/ Internal 2 channel VHF Wireless Receiver (3) 12v Rechargeable Battery (1) Tribank AC Power Adapter/Charger (allows up to (3) Loudspeakers to be powered/charged simultaneously). (3) Handheld Microphone (1) 2 Channel VHF Wireless Transmitter Pack with 9v Alkaline Battery (non rechargeable) (1) Remote Volume Control Dial with Stereo Splitter Cable (1) Lapel Microphone (1) Headset Microphone (1) Digital Voice Recorder Kit, includes: (1) Digital Voice Recorder (1) USB 2.0 Data Transfer Cable (1) 3.5mm (1/8") Stereo Patch Cable (1) 6.35mm (1/4") to 3.5mm Plug Adapter (2) AA Alkaline Batteries (non rechargeable) (3) Custom Padded Loudspeaker Deployment Case (1) Tripod with Custom Mounting Platform (supports up to (3) Loudspeakers simultaneously) Tri Bank AC Power/Charger Range Hailer Configuration: (3) Loudspeakers on Tripod with Custom Mounting Platform IMPORTANT NOTE: Standard Components & Accessories Delivered/Featured in this Operating Manual are Subject to Change Without Notice. 2.

LOUDSPEAKER, WIRELESS TRANSMITTER PACK & MICROPHONE SPECIFICATIONS Loudspeaker Specifications: Wireless Transmitter Pack Specifications: WEIGHT: ~ 8.1 lbs (3.67 kg) with battery installed WEIGHT: ~ 6 oz. (170.10 g) with battery installed DIMENSIONS: 8.5" X 7.1" X 11.2" (217 mm X 180 mm X 284mm) DIMENSIONS: 3.0" X 2.50" X 0.75" (144.30 mm X 63.5 mm X 19.05 mm) MIC IN: LINE IN: Power Supply: Charge Time: Operating Time: ~ 4 hrs INPUTS: 6.5mm (1/4") TRS Connector Port, Unbalanced 3.5mm (1/8") TRS Connector Port, Unbalanced POWER: 12vdc/2600mAh ~ 8 hrs (unlimited when connected to external power) Tx FREQUENCY CHANNELS: MODULATION SYSTEM: EFFECTIVE Tx RANGE: INPUT: POWER SUPPLY: POWER CONSUMPTION: 2 channel VHF Selectable; Frequency 1 (F1): 169.445 MHz, Frequency 2 (F2): 170.245 MHz FM 150 to 200 ft.. (45.72 M) Line of Sight (LOS) 3.5mm (1/8") Connector Port 9v Alkaline Battery (non rechargeable) ~ 30mA A/C Power Adapter/Charger: 18vdc/3 A Mains Voltage: 100 240v~, 50/60 Hz, 1.5 A (switching mode adapter) INTEGRATED/INTERNAL WIRELESS RECEIVER: Rx FREQUENCY CHANNELS: MODULATION SYSTEM: POWER SUPPLY: POWER CONSUMPTION: 2 channel selectable VHF; Frequency 1 (F1): 169.445 MHz, Frequency 2 (F2): 170.245 MHz FM Integrated with WFR Loudspeaker unit's Rechargeable Battery 25mA Microphone Specifications: (Front View) LAPEL MICROPHONE: HEADSET MICROPHONE: HANDHELD MICROPHONE: Omni Directional/Electret Condenser with 3.5mm (1/8") Mini Jack Connector Omni Directional/Electret Condenser with 3.5mm (1/8") Mini Jack Connector Dynamic/Hyper cardiode with 3 ft. (0.91 M) Spiral Cable with 6.5mm (1/4") Jack Connector Custom Padded WFR Loudspeaker Unit Deployment Case (Side View) (Front View) Lapel Mic Headset Mic Handheld Mic IMPORTANT NOTE: Specifications of Standard Components & Accessories Delivered/Featured in this Operating Manual are Subject to Change Without Notice. 3.

LOUDSPEAKER BATTERY CHARGING: The Loudspeaker and its internal/integrated 2 channel VHF Wireless Receiver are powered by (1) 12v rechargeable battery. When this battery is fully charged, the Loudspeaker and Wireless Receiver components can be operated for approx. 8 hours. An unlimited operating time can be achieved when the Loudspeaker unit is connected to an external power supply/120v electrical outlet. To charge a single Loudspeaker's battery: 1. Connect the AC Power Adapter/Charger to the AC Cable. 2. Connect the AC Cable to a 120v electrical wall outlet. 3. Insert the AC Power Adapter/Charger's pin into the Loudspeaker's DC IN power port (located on side). 4. Leave the Loudspeaker connected to the external power supply until the battery is fully charged. NOTE: The battery charging process may take up to (4) hours. The charge level of the battery may be checked by pressing the Loudspeaker's "CHECK BATTERY LEVEL" button (located on top). 5. Once fully charged, disconnect AC Power Adapter/Charger and AC Cable. The Wireless First Responder Range Hailer Configuration is delivered with a Tri Bank AC Power/Charger. The Tri Bank AC Power/Charger component allows for up to (3) Loudspeakers to be powered and/or charged from an external power supply simultaneously. To charge up to (3) Loudspeaker batteries simultaneously: 1. Set up the Tripod and Custom Mounting Platform. Tri Bank AC Power/Charger 2. Place a Loudspeaker into each of the trays located on the Custom Mounting Platform. 3. Use the handle located on the Tri Bank AC Power/Charger case to suspend the component from the "lip" located on the bottom on the Custom Mounting Platform. 4. Insert Tri Bank AC Power/Charger's AC plug into a 120v electrical wall outlet. 5. Insert the Tri Bank AC Power/Charger pin(s) into the "DC IN" power port(s) of the Loudspeaker(s) (located on side). 6. Leave the Tri Bank AC Power/Charger connected until the to the Loudspeaker battery is/are fully charged. NOTE: The battery charging process may take up to (4) hours. The charge level of the battery may be checked by pressing the Loudspeaker's "CHECK BATTERY LEVEL" button (located on top). 7. Once fully charged, disconnect the Tri Bank AC Power/Charger from the Loudspeaker(s) and electrical wall outlet. TRANSMITTER PACK BATTERY INSTALLATION: The Loudspeaker's internal/integrated Wireless Receiver receives audio signals from the 2 channel VHF Wireless Transmitter Pack which is powered by (1) 9v alkaline (non rechargeable) battery. When a new/unused battery is installed, the Wireless Transmitter Pack can be used for approx. 8 hours. To install a 9v battery into the Wireless Transmitter Pack: 1. Set the Wireless Transmitter Pack's switch (located on top) to the "TX OFF" position. 2. Open the Wireless Transmitter Pack s battery compartment cover (located on rear). 3. Install the 9v battery into the battery compartment accordance with the terminal's polarity (+/ ). 4. Replace the battery compartment cover. 4.

GENERAL OPERATING SAFETY GUIDELINES: Read, follow, heed all warnings and keep this operating manual. Do NOT use Loudspeaker(s) near water or during severe weather. Do NOT Throw, Drop or Aggressively Handle Loudspeaker(s) or Wireless Transmitter Pack as they contain sensitive electronic components! Do NOT use components near ANY heat source such as radiators, heat registers, stoves or other devices (including amplifiers) that produce heat. Unplug Loudspeaker(s) during lightning storms. Refer all servicing to Enforcement Technology Group, Inc. (ETGI) personnel. Servicing is required when component(s) have been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into component(s), componen(s) have been exposed to rain or moisture, component(s) do NOT operate normally or component(s) has been dropped. CAUTION!: To reduce the risk of electric shock; do NOT remove the top cover (or the rear section) as NO user serviceable parts are located inside. CAUTION!: Loudspeaker(s) contain a rechargeable battery. Rechargeable batteries must NOT be exposed to fire this poses a DANGER OF EXPLOSION. Incorrectly replacing the battery poses a DANGER OF EXPLOSION. Only use batteries of the same type. The capacity of the battery may diminish at low temperatures. CAUTION!: The Loudspeakers are capable of delivering sound pressure levels in excess of 105dB, which may cause permanent hearing damage. INTRODUCTION TO REMOTE/ WIRELESS OPERATIONS: Remote/wireless operations refers to the Transmitter Pack's ability to wirelessly transmit audio data from the audio source in which it is connected to the internal/integrated wireless receiver contained within a single or multiple Loudspeakers to distances between 150 to 200 ft. away.** To allow for wireless transmission to occur, the following MUST be ensured: 1. The Wireless Transmitter Pack and Loudspeaker(s) must be powered on. 2. An audio source (microphone or external audio source such as a Digital Voice Recorder, MP3 player, or CD Player, etc ) must be connected to the Wireless Transmitter Pack s MIC/AUDIO SOURCE IN jack. 3. The Wireless Transmitter Pack and the Loudspeaker(s) must be set to the same frequency. **It is important to note that the effective remote/wireless operating range varies and dependent upon several factors. These factors include, but are not limited to the power level of each component as well as the operating environment/the number of obstacles that are blocking the wireless transmission path. Establishing a clear, line Of sight (LOS) path between the Wireless Transmitter Pack and the Loudspeaker(s) will maximize the effective remote/wireless operating range. The Wireless Transmitter Pack is also delivered with a Remote Volume Control Dial. This component allows the operator to remotely increase/decrease the Loudspeaker(s) audio broadcast volume output level. 5.

INTRODUCTION TO REMOTE/ WIRELESS OPERATIONS (Continued): IMPORTANT NOTE: LOUDSPEAKER MAXIMUM VOLUME OUTPUT LEVEL & REMOTE VOLUME CONTROL The position of the Loudspeaker's MIC LEVEL dial (located on side) establishes the maximum volume output level of the unit. To prevent damage to the Loudspeaker's circuitry, the unit's MIC LEVEL dial should NEVER be set to a position of more than 80% percent of its MAX level. During remote/wireless operations, the Wireless Transmitter Pack's Remote Volume Control Dial can be used to decrease the Loudspeaker's volume output level and/or return the unit to its maximum volume output level as dictated by the "MIC LEVEL" dial. REMOTE/WIRELESS OPERATIONS: 1. Insert the Remote Volume Control Dial's male plug into the Wireless Transmitter Pack s MIC/AUDIO SOURCE IN jack. NOTE: Check that the Remote Volume Control Dial component is set to a low/mid volume output level (positioned to the left). 2. Insert the Remote Volume Control Dial's male plug into the Wireless Transmitter Pack s MIC/AUDIO SOURCE IN jack. NOTE: Check that the Remote Volume Control Dial component is set to a low/mid volume output level (positioned to the left). 3. Insert the Lapel or Headset Microphone's male pin into the Remote Volume Control Dial's female jack. ** 4. Power on the Wireless Transmitter Pack by setting the device's switch (located on top) to either the Tx F1 POWER ON (Frequency 1) or F2 TX F2 POWER ON (Frequency 2) position. NOTE: The Wireless Transmitter Pack s LED will turn on to signal that the device is receiving power. 5. Check that the Loudspeaker's internal Wireless Receiver's frequency select switch (F1/F2 located on top) is to the SAME frequency (either F1 or F2) that the Wireless Transmitter Pack is set to. 6. Replace the Loudspeaker's rear compartment cover. 7. Check that the Loudspeaker's MIC LEVEL dial is set to a low/mid volume output level (positioned to the left) and power up the Loudspeaker by pressing the unit's POWER button (located on side). NOTE: The POWER button will turn green signaling that the unit is receiving power. 8. After powering on the Loudspeaker, turn the unit s MIC LEVEL dial (clockwise) towards the MAX setting. NOTE: To prevent damage to the Loudspeaker's circuitry, do NOT positioned the MIC LEVEL dial to more than 80% of its MAX level. 9. To prevent damage to the Loudspeaker during use or when operating in inclement weather, place the unit inside the custom/padded deployment case (provided). NOTE: If Range Hailer configuration is used place Loudspeaker(s) on Tripods and Custom Platform Mount. 10. Speak into the Lapel or Headset Microphone connected to the Remote Volume Control Dial connected to the Wireless Transmitter Pack. NOTE: The audio signals picked up by the microphone will be wirelessly transmitted and broadcast through the Loudspeaker. To increase Loudspeaker s volume output level, turn the REMOTE VOLUME CONTROL DIAL clockwise. To decrease the Loudspeaker s volume output level, turn the REMOTE VOLUME CONTROL DIAL counter clockwise. 11. After operations, power off the Wireless Transmitter Pack by setting the device s switch to the Tx Power OFF position. NOTE: The Wireless Transmitter Pack s LED will turn off to signal that the device has been powered off. 12. Follow the procedures listed in the Battery Charging, Maintenance & Storage section of this manual. 6.

REMOTE/WIRELESS OPERATIONS CONNECTING TO AN EXTERNAL AUDIO SOURCE: ** NOTE: The Wireless Transmitter Pack may also be connected to an external audio source such as a Digital Voice Recorder, MP3 player, CD player, etc to allow the device's audio to be broadcast through the Loudspeaker(s). To connect the Wireless Transmitter Pack to an external audio source: 1. Insert the Remote Volume Control Dial's male plug into one of the two female jacks located on the Stereo Splitter Cable. NOTE: Check that the Remote Volume Control Dial component is set to a low/mid volume output level (positioned to the left). 2. Insert one of the Stereo Patch Cable's male plugs into the external audio device source s 3.5mm (1/8 ) HEADPHONE or EAR output jack. NOTE: To connect to an external audio device source with a 6.35mm (1/4 ) output port, use the 3.5mm to 6.35mm Adapter (provided). 3. Insert the Stereo Patch Cable's other male plug the Remote Volume Control Dial's female jack. 4. Power up and set the external audio source s volume output to a mid/high level. 5. To begin the wireless audio broadcast, press the external audio device s play button and follow steps 2 8 in the REMOTE/WIRELESS OPERATIONS section of this manual. Connecting an External Audio Source to the Wireless Transmitter Pack Diagram Stereo Patch Cable Stereo Splitter Cable Digital Voice Recorder (External Audio Source Example) Remote Volume Control Dial Wireless Transmitter Pack ** NOTE: The Wireless Transmitter Pack may also be connected to the Lapel or Headset Microphone AND a Digital Voice Recorder simultaneously. This allows for the operator to digitally record the audio that is being picked up by the microphone/broadcast through the Loudspeaker(s). NOTE: When the Wireless Transmitter Pack is Configured in this manner one is NOT able to use the Remote Volume Control Dial feature. 7.

REMOTE/WIRELESS OPERATIONS CONNECTING A DVR & MICROPHONE: To connect the Wireless Transmitter Pack to a Lapel or Headset Microphone AND a Digital Voice Recorder, please follow these steps: 1. Insert the Stereo Splitter Cable's male plug into the Wireless Transmitter Pack's "MIC IN" jack. 2. Insert the Lapel OR Headset Microphone s male plug into one of the two Stereo Splitter Cable's female jacks. 3. Insert one of the Stereo Patch Cable's male plugs into the Digital Voice Recorder's 3.5mm (1/8 ) MIC IN jack. 4. Insert the Stereo Patch Cable's other male plug the Stereo Splitter Cable's available female jack. 5. Power on the Digital Voice Recorder and press the device s REC button. 6. To begin the wireless audio broadcast and recording follow steps 4 10 in the REMOTE/WIRELESS OPERATIONS section of this manual. Connecting a Digital Voice Recorder & Lapel OR Headset Microphone to the Wireless Transmitter Pack Diagram Stereo Patch Cable Stereo Splitter Cable OR Lapel Mic Headset Mic Digital Voice Recorder (External Audio Source Example) Wireless Transmitter Pack 8.

LOCAL/WIRED OPERATIONS: Local/wired operations refer to the Loudspeaker's ability to broadcast audio when it is connected directly to a microphone or an external audio source. 1. Insert the Handheld Microphone s plug into the Loudspeaker's MIC IN. port. NOTE: To avoid feedback during operations, NEVER hold the microphone directly in front of the Loudspeaker when powered on.** 2. Check that the Loudspeaker's MIC LEVEL dial is set to a low/mid volume output level (located on side) and power on the Loudspeaker unit by pressing the POWER button. NOTE: The POWER button will turn green signaling that the unit is receiving power. 3. After powering on the Loudspeaker, turn the MIC LEVEL dial (clockwise) towards the MAX setting. NOTE: To prevent damage to the Loudspeaker's circuitry, do NOT positioned the MIC LEVEL dial to more than 80% of its MAX level. 4. Set the Handheld Microphone s switch to the ON position. 5. To prevent damage to the Loudspeaker during use or when operating in inclement weather, place the unit inside the custom padded loudspeaker deployment case (provided). 6. To power off the Loudspeaker, press the POWER button. NOTE: The POWER LED will turn off signaling that the unit is powered off. 7. Follow the procedures listed in the Battery Charging, Maintenance & Storage section of this manual. ** NOTE: The Loudspeaker also broadcast audio data from other external audio sources such as a Digital Voice Recorder, MP3 player, CD Player, etc To connect the Loudspeaker to an external audio source: 1. Insert one of the 3.5mm (1/8") Stereo Patch Cable male plugs into an external audio device source s 3.5mm (1/8 ) female HEADPHONE or EAR output jack. NOTE: To connect to an external audio device source with a 6.35mm (1/4 ) output jack, use the 6.35mm (1/4") to 3.5mm Plug Adapter (provided). 2. Insert the other end of the 3.5mm (1/8") Stereo Patch Cable into the Loudspeaker's the LINE IN jack (located on side). 3. Power on and set the external audio source s volume level to a mid/high setting. 4. To begin the external audio device source audio broadcast, press the external audio device s play button and follow steps 2 7 in the LOCAL/WIRED OPERATIONS section of this manual. Connecting the Loudspeaker to an External Audio Source Diagram: Stereo Patch Cable 9.

BATTERY CHARGING, MAINTENANCE & STORAGE: IMPORTANT NOTE: To maximize the performance of the Loudspeaker, the following battery charging/maintenance procedures should be followed EACH time that a Loudspeaker has been used OR once every month. To charge a single Loudspeaker battery: Connect the AC Power Adapter/Charger to the AC Cable. Connect the AC Cable to a 120v electrical wall outlet. Insert the AC Power Adapter/Charger's pin into the Loudspeaker's DC IN power port (located on side). Leave the Loudspeaker connected to the external power supply until the battery is fully charged. NOTE: The battery charging process may take up to (4) hours. The charge level of the battery may be checked by pressing the Loudspeaker's "CHECK BATTERY LEVEL" button (located on top). Once fully charged, disconnect AC Power Adapter/Charger and AC Cable. The Wireless First Responder Range Hailer Configuration is delivered with a Tri Bank AC Power/Charger. The Tri Bank AC Power/Charger component allows for up to (3) Loudspeakers to be powered and/or charged from an external power supply simultaneously. To charge up to (3) Loudspeaker batteries simultaneously: 1. Set up the Tripod and Custom Mounting Platform. Tri Bank AC Power/Charger 2. Place a Loudspeaker into each of the trays located on the Custom Mounting Platform. 3. Use the handle located on the Tri Bank AC Power/Charger case to suspend the component from the "lip" located on the bottom on the Custom Mounting Platform. 4. Insert Tri Bank AC Power/Charger's AC plug into a 120v electrical wall outlet. 5. Insert the Tri Bank AC Power/Charger pin(s) into the "DC IN" power port(s) of the Loudspeaker(s) (located on side). 6. Leave the Tri Bank AC Power/Charger connected until the to the Loudspeaker battery is/are fully charged. NOTE: The battery charging process may take up to (4) hours. The charge level of the battery may be checked by pressing the Loudspeaker's "CHECK BATTERY LEVEL" button (located on top). 7. Once fully charged, disconnect the Tri Bank AC Power/Charger from the Loudspeaker(s) and electrical wall outlet. 10.